Hi there,
let me first thank you for this great site you put up here!
And here comes my question:
I want to hook up my USB GPS Mouse (made for the notebook -
meaning it get's it's power via USB) up to my XDA.
And now I wonder if I can simply solder the data +/- cables
from the USB Mouse to the USB data +/- pins on the XDA plug
(so I could still use the same cable for ActiveSync on the PC),
or if I have to solder the data +/- cables from the USB mouse
to the serial RX/TX pins as described on the 'The XDA's connectors'
page of this site...
I was planning to hook both the GPS and the XDA up to my car
power adaptor in a kind of a Y constellation:
::::::::::::::::::::::::::::::::__________ Power
:::::::::::::::::::::::::::::::/
::::::::::::::::::::::::::::::/
::::::::::::::XDA ----------
::::::::::::::::::::::::::::::\
:::::::::::::::::::::::::::::::\___________ GPS
and use Power for both.
Maybe someone can tell me about the data hookup.
Thanks, Lars.
I don't have answers but some things you have to consider.
1) The XDA is a slave device. I presume the GPS receiver is one too. I really wonder if they can communicate with eachother
2) Based on how you describe this you want to power the receiver from the the car. I assume you have checked the right voltage requirements for the receiver and that the powersupply can deliver the currents required for both the XDA and the receiver. My personal experience is that the latter shouldn't be too much of a problem, but it can't hurt to check.
3) Combining USB and Serial the way you describe it is not a good idea. (mark the last character '.' as in PERIOD).
Robert
Power Supply
Hi Robert,
thanks for your suggestions.
Indeed both (the original ActiveSync cable from the XDA and the
USB GPS) get their power off a USB port on the notebook so
this must be the same voltage requirements.
This ActiveSync cable is a combined car charging cable with an
USB 'A' type connector on the end which you can plug either into
the USB port on the notebook (where it also ActiveSync's) or into
the car's power adapter (where it only charges).
So this both same voltage. And the car power adaptor should
nominally supply enough power for both...
But I don't understand what you said about it not beeing a good
idea to hook up the USB data to the SERIAL data.
When plugged into the notebook in WinXP the USB GPS installs
a 'Prolific USB-to-Serial COM5' to emulate to the programms
working with it a com5 (or com1 or com2 depending on your
hardware settings) communications port. So I guess the data
coming from the USB GPS is just the same as if delivered via
serial cable and all the driver does is faking to be a serial port
to any programm asking for data from com5.
And I think a USB device is 'not really' a passive device as it starts
popping out ASCII data strings as soon as it get's power (no matter
if there is a device to read the data or not).
So I figure when you plug it into the XDA and tell the XDA by means
of USB wakeup (USB_VDD pin 13) that there is an active USB
connection, that it will start trying to figure out what the heck the
connected cable is trying to tell it.
And here is the tricky part where I don't know if the XDA might not
believe it is beeing Sync'ed and therefore starts ActiveSync.
Anyone with any experience or suggestions there...??
(Sorry for the rather lenghty post)
Greetings, Lars.
Lars,
seems like you got the power all figures out
regarding the usb/serial discussion.
If I understand you correctly you can plug the USB connector of the GPS receiver into the USB port of the PC.
'somewhere' in the PC this is modified into a virutal serial port in order to enable serialport aware programs to work with the GPS receiver as well.
This is a good concept but at an electrical level that still means that the GPS receiver is connected in an USB fashion. There is nothing Serial Port about that. In a way you already pointed that out in your messages by using the word 'emulate'.
You can hook it up to the USB part of the XDA but still I doubt about the master/slave discussion of USB.
Regards Robert
No cahnce.
Save yourself time/money.
Forget it.
Lars said:
Hi there,
let me first thank you for this great site you put up here!
And here comes my question:
I want to hook up my USB GPS Mouse (made for the notebook -
meaning it get's it's power via USB) up to my XDA.
And now I wonder if I can simply solder the data +/- cables
from the USB Mouse to the USB data +/- pins on the XDA plug
(so I could still use the same cable for ActiveSync on the PC),
or if I have to solder the data +/- cables from the USB mouse
to the serial RX/TX pins as described on the 'The XDA's connectors'
page of this site...
I was planning to hook both the GPS and the XDA up to my car
power adaptor in a kind of a Y constellation:
::::::::::::::::::::::::::::::::__________ Power
:::::::::::::::::::::::::::::::/
::::::::::::::::::::::::::::::/
::::::::::::::XDA ----------
::::::::::::::::::::::::::::::\
:::::::::::::::::::::::::::::::\___________ GPS
and use Power for both.
Maybe someone can tell me about the data hookup.
Thanks, Lars.
Click to expand...
Click to collapse
Guess U R right
Hi Guys thanx for the feedback,
I spent an afternoon researching on this stuff and am very disappointed that I have to admit you are both right.
Now way (other than putting some 'intelligent' converter between the USB GPS and the RX/TX pins of the XDA) to make the USB 'language' sound like 'SERIALean'.
I think there should still be a possibility:
Let everything run via the USB, persuade the XDA it's not ActiveSync talking to it and write a driver that talks to the GPS via the open USB connection and sends the proper commands to recieve the NMEA ASCII.
And then you would still need to tell your route software to take the incoming data from the virtual (or emulated) COM port...
And when I read the above chapter once more :shock: I find this is definitly not a job for me!!
So I will just get a serial GPS an hook it up the nomal way.
Cheers and thanx again, Lars.
Hi,
Just read your post. I am new to pda land. Just bought a xda2
I have a laptop which I use with a gps usb mouse via usb on the laptop. Am I right in thinking that I could have bought a ps2 mouse and used a ps2 changer to usb and it would have worked??
If so can't I buy a usb to ps2 changer in order to plug into a car connection cable which has the ps2 and the xda conection and a ciger lighter plug for power? OR is there a similar cable for a usb connect for gps?
Am I missing something here?
Thanks
P
Related
Hi everybody,
I've got problems with connecting my Rikaline 6010 to the Car Kit. With the help of the forum I know now, wich pins I have to connect together. But I'm not be able to bring power to the Mouse. I have the +5V and GND connected but the LED on the mouse won't turn on. With a simple car adapter for the mouse and the xda it works perfect. I try to look inside the cable of the car adapter and it looks lite the cable, I build myself.
Maybe I have to short some pins inside the connector ??
Does anybody have a Rikaline 6010 successful connected to the xda car kit ?
thanks a lot
rob.
Make sure the switched power supply is connected.
I assume you are using the official XDA carkit.
I did some reverse engineering on this carkit and found that the GPS powerline is only working if the switched power line for the carkit is connected.
After disconnecting this line the GPS power will stay on for 1 hour and then automatically switch of.
Have you checked if there is power on the GPS connector of the carkit when nothing is connected? Maybe the current demand is to high? For pinlayout check www.vanhemert.biz
Francois
Hi Francois,
I think my problem is not the car kit. After it doesn't work with the carkit, I tried to connect my car-adapter-cable with the cable, I made myself to the gps-mouse. And also there, the mouse doesn't get power. So I simply put +5V and GND to the pins of the mouse-connection and it doesn't work.
Maybe GND must be connected to two pins or to the GND-pin AND the PS2-connector's metall ?
I think, I have to buy a H203e to make it work....
rob.
Pinlayout
I have looked at the data sheet (http://www.rikaline.com/pdf/gps-6010-manual-e.pdf) and it looks straightforward. Pin 2 and 4 should do the job but I can imagine that you need a correct RS232 signal to get the thing up and running. Are you sure that the LED is just an indication of power or does it only light if power and RS-232 is correct?
As you can see in the schematics on my website I had trouble opening the COM port on my XDA, Communication just did not start unless I pulled the DCD line (pin 6) to Vcc. This will activate Active sync in the same way as the original cable set I used to have.
Good luck,
Francois
Hi,
thanks for your reply. The LED on the GPS-Mouse have to turn on simply by bringing power to it. I've tried that by using my car adapter cable and simply connect the mouse to the cable and not connect the xda...and the LED turns on.
I've ordered today a Hi203E and I will try to conncet it as you described on your homepage....hope it will work (if not, I'll be back ;-))
thanks a lot
rob.
Hi Francois,
today I received my Hi203e and I will try to connect it to the carkit.
One Question:
Is the connector, which is shown on your homepage and labeled with "to gps" the female connector, which is wired to the gps-mouse or the male connector, which is wired on the selfmade cable between carkit and PS2-connector of the mouse ??
thanks
rob.
hi,
ok, my previous question is now obsolet. The connector, which is wired to the Hi203e, is male (at my Rikaline6010 it is female). So I have to buy a female connector and build new cable. I made a first test by bringing the +5V and GND of the carkit over an adaptercable to the gps-mouse and (yippie) it worked. The LED on the mouse turns on !! Looks pretty good.
...to be continued (if I have the new connector...)
rob.
Hi Francois,
I've got it now and it works perfect. Thanks again for the Info's on your webpage.
2 points:
I've got a low noise (frequently repeated) in the speaker, when the gps is active. Is there something to do against that ?
And how can I stop the activation of active-sync, when i put the xda into the carkit ?
Do you know that ?
thanks
rob
noise...
rob said:
I've got a low noise (frequently repeated) in the speaker, when the gps is active. Is there something to do against that ?
Click to expand...
Click to collapse
I would guess this is the speaker wire picking up the GSM signal, nothing to do with the GPS. Try re-aligning so that the wires relative to the antenna of the XDA. If that doesn't work, you could experiment with ferrite beads (these ugly black blocks on all modern cables) on the wires.
Same problem here, but...
I found that if I start serial communication with the GPS unit, i will hear some interferance via the speaker. It looks like the auto mute functions does not work immediatlly after inserting the XDA and "the connection is left open".
Workaround:
Pressing the red phone button to generate a tone (keypress) activates the automute and the interferance will disappear. (at least is does in my case)
Auto start of the active sync process:
This is caused by the DCD line pulled to Vcc. I first owned a standard GPS Y-cable (XDA/GPS/Lighter) and it showed the same behaviour. My first experiment was to not use the DCD line (just gnd, tx and rx)but at that time TomTom could not open the COM port. I did no further investigation but one of the forum members suggested to disable the IR connection and auto sync, this should free the com port to TomTom and not start active sync automatically. Again I have not tested it but if you will, i am interested.
Good luck,
francois
hi,
Been reading this thread with alot of interest...
can someone help me with a problem, I have the O2 carkit installed in my car, and i also have a rikaline 6010 that i would like to attach it.
I have found the GPS connector that i need to attach the GPS reciever to but when i check the connector for +5v its not there...
Does anyone know where i can connect it to... looks like the person who connect my carkit could'nt be bothered about connecting up the GPS connector properly...
and also the colour of wires that everyone mentions, mine are a different colour...
i have the following from my rikaline reciever, 4 in total...
red
black
green
white
does anyone know what connects to what????
Many Thanks
Zetex
Rikalinegps 6010 with cables - from eBay
This receiver is available with cable for XDA via eBay (see link below), but you guys have got me worried. I'm thinking of buying the Rikaline 6010 but am I going to have to do all this business of rewiring etc? What's the economical way of buying all the other bits that I need (Software, Car Kit etc)?
I'm looking for some easy to follow advice. Keep it simple please.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=4668&item=3094896604&rd=1
:? :? :?
I don't know much about USB. I was thinking coming up with ONE cable with three connectors like the one I draw blow.
Code:
XDA -------USB (to laptop or ac adaptor)
|
|
GPS (the generic GPS connect).
NOTE: the ac adaptor output port is an USB port
it serves for three ways
a), XDA -> Laptop, charge and syn in the same cable, draws power from laptop
b). GPS -> laptop, draws power from laptop
c). XDA -> GPS, in this case, USB connector connects to the ac adapter and power both GPS and XDA.
I believe the XDA---USB cable can be purchased easily. I can break the cable and somehow insert the GPS connector. since GPS only used a power pin, two data pin, a ground pin, I figure I only need to find out how to get these four pin into the original cable.
My question is
1. do I need any USB-serial sort of convertor between the lines? Or it is ok to connect GPS(serials signal) to USB cable
2. The ac adapter was to power the XDA which I blieve is 6V, and GPS needs 5 V, is it OK?
3. anyone alreadys knows how to plug the four GPS pins to USB cable? would save me a lot of trouble.
It would be cool to have a cable connects between all devices. If you can care for a DC-AC convertor in your car, this set should solve all your problem anywhere.
help is appreciated.
Most GPS units are serial. The XDA does have serial, so you can use that. You only need to connect the ground and two data pins. Specified input power for the XDA is 5v.
You can see what I did with a cradle to make a car kit here:
http://www.mywirelessoffice.com/xda/carkit/
This is a pin spec and photo of the connector:
http://www.mywirelessoffice.com/xda/connector/
There is a source for bare connetors, I believe the link is here on the XDA-Dev site somewhere.
Re: XDA -> Laptop USB, GPS-> laptop USB, are they the
It is possible. But note:
1. I assume you are using a serial GPS (with appropriate wiring), then it is OK. USB GPS CANNOT be used.
2. USB sync cable is wired to tell XDA that USB sync cable is connected so as to "wake up" the USB port. In such case, I do not know wheter the serial port can be accessed. As such has not been done before you have to try before you know.
I would suggest you make a cable just for GPS use, and use another cable for sync/charge (this is quite cheap), unless you found that your original idea works.
pine said:
I don't know much about USB. I was thinking coming up with ONE cable with three connectors like the one I draw blow.
Code:
XDA -------USB (to laptop or ac adaptor)
|
|
GPS (the generic GPS connect).
NOTE: the ac adaptor output port is an USB port
it serves for three ways
a), XDA -> Laptop, charge and syn in the same cable, draws power from laptop
b). GPS -> laptop, draws power from laptop
c). XDA -> GPS, in this case, USB connector connects to the ac adapter and power both GPS and XDA.
I believe the XDA---USB cable can be purchased easily. I can break the cable and somehow insert the GPS connector. since GPS only used a power pin, two data pin, a ground pin, I figure I only need to find out how to get these four pin into the original cable.
My question is
1. do I need any USB-serial sort of convertor between the lines? Or it is ok to connect GPS(serials signal) to USB cable
2. The ac adapter was to power the XDA which I blieve is 6V, and GPS needs 5 V, is it OK?
3. anyone alreadys knows how to plug the four GPS pins to USB cable? would save me a lot of trouble.
It would be cool to have a cable connects between all devices. If you can care for a DC-AC convertor in your car, this set should solve all your problem anywhere.
help is appreciated.
Click to expand...
Click to collapse
Hello,
I have a USB OTG cable and dell keyboard that I have tested and work in OTG mode on a Nexus 7, however i cannot get them to function with my HP Touchpad 32gb, running CM9 2.6.35, built on Sun Oct 28.
The device recognizes when I plug in anything via USB, but only as a generic Linux USB hub, and not as any particular device. Are there any steps to take to debug this? Has anyone had experience with this type of an issue?
Thanks for your help,
Cory
I don't know if this is the issue, but I know the touchpad doesn't support OTG like the the Nexus does. I think you need a Y-adapter + OTG to provide power since the micro usb port doesn't give any power to the device you connect. Someone correct me if I'm wrong though.
Apparently even a powered USB requires a powered Y cable to be properly recognized. I hacked together a quick Y cable manually, by splicing in another USB cable's power and ground (Red and black) to the respective locations on a female USB cable. Works as expected.
I am now communicating with an Arduino over Serial
Thanks!
Read this thread, should give you all the info you need:
http://forum.xda-developers.com/showthread.php?t=1582771
Basically the Touchpad has OTG but it provides no power.
wcdolphin said:
Apparently even a powered USB requires a powered Y cable to be properly recognized. I hacked together a quick Y cable manually, by splicing in another USB cable's power and ground (Red and black) to the respective locations on a female USB cable. Works as expected.
I am now communicating with an Arduino over Serial
Thanks!
Click to expand...
Click to collapse
I'm curious if you are able to charge with this cable hack while using usb devices?
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
ZedZardoz said:
I'm curious if you are able to charge with this cable hack while using usb devices?
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
Click to expand...
Click to collapse
if so , he is the first of the many many many who has used this cable..HPTP just is not set up for charge + usb data at the same time
amkaos said:
if so , he is the first of the many many many who has used this cable..HPTP just is not set up for charge + usb data at the same time
Click to expand...
Click to collapse
Agreed. I think people just are not stating reality regarding the ability to charge and use OTG Hosting to USB devices at the same time.
My goal here has been to attach a flash drive with video/audio media and play & charge on long flights. It looks like play, charge are mutually exclusive on my beloved TouchPad.
I've asked for the specific confirmation of this from this YouTube but have never had the poster reply:
https://www.youtube.com/watch?v=p10LgZFIawo&feature=BFa&list=PLCED27D4A23068E04&index=7
There are devices out there that have very advanced micro USB device implementations. Sadly the HP is only superficially supportive.
I for one cannot wait to get my SGN2 smart dock which offers:
Charging
OTG (x3 USB)
Audio out
HML HDMI out
Docked Profile
I want your experience in psu schematics.This is my plan, I will buy a cheap usb hub,,I will power it with dvd player smps 5V at the same time it will supply parallel to pi micro usb socket.My question is ,Do you cut the upstream power from usb hub when you are connecting the hub? do you left it as it is,,may be a diode is present.
PREMOLIKES said:
I want your experience in psu schematics.This is my plan, I will buy a cheap usb hub,,I will power it with dvd player smps 5V at the same time it will supply parallel to pi micro usb socket.My question is ,Do you cut the upstream power from usb hub when you are connecting the hub? do you left it as it is,,may be a diode is present.
Click to expand...
Click to collapse
While I can't answer specifics on what wires to connect I would recommend taking a look at this great guide to building your own PSU for the RPi http://elinux.org/RPi_5V_PSU_construction. This includes circuit diagram layouts.
Sent from my SCH-I535 using xda premium
I have my Pi powered from one of the normal USB ports. The power comes from the 'power' cable of the USB hard disk that is attached to the Pi. The hard disk's main USB cable is plugged into a powered USB hub.
Attached an image.
Do we need push more mA into her. mines running off my Tab2`s charger at the moment which is 2 Amps..??
lodger said:
Do we need push more mA into her. mines running off my Tab2`s charger at the moment which is 2 Amps..??
Click to expand...
Click to collapse
That should be enough amps as most phone and tablet chargers will provide the 5-5.6V of power needed for the RPi to function properly.
Sent from my SCH-I535 using xda premium
2A will be sufficient to power a couple of peripherils including pi itself.
powered USB hub...
Hey guys, it seems ive got power issues with my pi, everything works fine if i just use the two usb ports, but as soon as i plug in my powered usb hub i get keyboard errors, bluetooth dropping, and wifi connection issues, all symptoms of low power. anyone having this issue with thier Raspi & powered usb hub?
justanotherlurker said:
Hey guys, it seems ive got power issues with my pi, everything works fine if i just use the two usb ports, but as soon as i plug in my powered usb hub i get keyboard errors, bluetooth dropping, and wifi connection issues, all symptoms of low power. anyone having this issue with thier Raspi & powered usb hub?
Click to expand...
Click to collapse
Exactly how do you have everything plugged in?
Assuming power to pi from one source, hub to the USB port and your accessories all to the hub: See if you can get your pi to boot with the hub plugged in to the accessory port but nothing to the power micro USB.
I suspect the hub may be causing issues by backfeeding power through the accessory port. This test will tell.
powered USB hub...
cjdalessio said:
Exactly how do you have everything plugged in?
Assuming power to pi from one source, hub to the USB port and your accessories all to the hub: See if you can get your pi to boot with the hub plugged in to the accessory port but nothing to the power micro USB.
I suspect the hub may be causing issues by backfeeding power through the accessory port. This test will tell.
Click to expand...
Click to collapse
You guessed correctly to how i had it all set up. I did exactly what you said, tried booting, but got nothing. i dont think its backfeeding, any other suggestions? this one leaves me scratching my head.
justanotherlurker said:
You guessed correctly to how i had it all set up. I did exactly what you said, tried booting, but got nothing. i dont think its backfeeding, any other suggestions? this one leaves me scratching my head.
Click to expand...
Click to collapse
Are you using seperate power for usb hub ?If it is so you should cut the power terminal from usb hub to pi.See that you are supplying good current to the hub.
Does the USB port have any other function other than power?
Don't think so, only power AFAIK.
I plugged it into my computer and even tried pressing and pressing/holding the button on the Chromecast but my computer didn't indicate any hardware plugged in.
I wonder if the data pins are even wired to anything internally.
UPDATE: The USB cable that comes with it may not work for data transfer, tried it with my phone and it didn't work. So I tried a normal microUSB cable but still nothing.
spunker88 said:
I plugged it into my computer and even tried pressing and pressing/holding the button on the Chromecast but my computer didn't indicate any hardware plugged in.
I wonder if the data pins are even wired to anything internally.
Click to expand...
Click to collapse
If we could plug a mouse or keyboard into it would be great!!
comatose1978 said:
If we could plug a mouse or keyboard into it would be great!!
Click to expand...
Click to collapse
It has bluetooth... so in theory that could be a simple alternative... we just need to figure out how to access hidden menus.
comatose1978 said:
If we could plug a mouse or keyboard into it would be great!!
Click to expand...
Click to collapse
I tried this with a self powered USB OTG cable, just to see if the Chromecast would blink, bing, or do anything to show recognition, no dice. Also tried booting with a USB drive in, no difference.
Universal Charger
Universal Charger:victory:
Examining board
Based on examining the photos of the motherboard on ifixit.com...
Component EM1 appears to be a USB Common Mode Choke. That goes on the D+/D- pair which you can see routed from the USB port, so it wouldn't be present if there wasn't some use for data communication over the USB port. (Cost sensitive equipment.) The flip side of the PCBA shows TP1-TP20 (Where TP19 and TP20 appear to be GND). My guess is in that mix you have a JTAG port for programming/testing the unit initially with a pogo pin rig (evidenced by the dimples observed in each of those locations), and there might be more high/low GPIO pins where one might allow the unit to enter its USB data mode.
-Jon
ften said:
I tried this with a self powered USB OTG cable, just to see if the Chromecast would blink, bing, or do anything to show recognition, no dice. Also tried booting with a USB drive in, no difference.
Click to expand...
Click to collapse
Is there any special kind of powered otg cable to work with this? I looked on Amazon but not sure. I want to grab one incase they make any progress on rooting this.
Sent from my HTCONE using Tapatalk 4 Beta
mustang_52 said:
Is there any special kind of powered otg cable to work with this? I looked on Amazon but not sure. I want to grab one incase they make any progress on rooting this.
Sent from my HTCONE using Tapatalk 4 Beta
Click to expand...
Click to collapse
Looks like its already been rooted. With what looks like a dual usb otg. They don't go deep into what specific cable but, I would guess it is a generic dual usb one off ebay, or amazon, heres a quick one i pulled from amazon http://www.amazon.com/Micro-Cable-P...8&qid=1375052489&sr=8-3&keywords=Dual+Usb+otg
But if you read into it, they say you can root, but unless your a developer you probably wont get any benefit of rooting....yet, if at all.
Obtaining root Link: http://blog.gtvhacker.com/2013/chromecast-exploiting-the-newest-device-by-google/
OneAn9ryN00b said:
Looks like its already been rooted. With what looks like a dual usb otg. They don't go deep into what specific cable but, I would guess it is a generic dual usb one off ebay, or amazon, heres a quick one i pulled from amazon http://www.amazon.com/Micro-Cable-P...8&qid=1375052489&sr=8-3&keywords=Dual+Usb+otg
But if you read into it, they say you can root, but unless your a developer you probably wont get any benefit of rooting....yet, if at all.
Obtaining root Link: http://blog.gtvhacker.com/2013/chromecast-exploiting-the-newest-device-by-google/
Click to expand...
Click to collapse
Please correct me if Im wrong, but the cable you linked only charges the thumbdrive/keyboard/mice/etc NOT the Chromecast so how would one root it since it does need power from usb plug? I've been searching for correct cable and cant find it; link to correct cable would be greatly appreciated!!!
This cable wouldnt work, right? http://www.ebay.com/itm/Usb-type-A-..._USB_Cables_Hubs_Adapters&hash=item4857e3608e
eurominican said:
Please correct me if Im wrong, but the cable you linked only charges the thumbdrive/keyboard/mice/etc NOT the Chromecast so how would one root it since it does need power from usb plug? I've been searching for correct cable and cant find it; link to correct cable would be greatly appreciated!!!
This cable wouldnt work, right? http://www.ebay.com/itm/Usb-type-A-..._USB_Cables_Hubs_Adapters&hash=item4857e3608e
Click to expand...
Click to collapse
I own that cable from Amazon and it should work. It brings in +5v from a charger connected to the female microUSB port and then splits it to the female full size USB port and the the male microUSB port so both the USB host device and the USB peripheral device are getting power.
spunker88 said:
I own that cable from Amazon and it should work. It brings in +5v from a charger connected to the female microUSB port and then splits it to the female full size USB port and the the male microUSB port so both the USB host device and the USB peripheral device are getting power.
Click to expand...
Click to collapse
I ordered this cable http://r.ebay.com/QgwBIW Will report back if it works when I get it.
eurominican said:
Please correct me if Im wrong, but the cable you linked only charges the thumbdrive/keyboard/mice/etc NOT the Chromecast so how would one root it since it does need power from usb plug? I've been searching for correct cable and cant find it; link to correct cable would be greatly appreciated!!!
Click to expand...
Click to collapse
I also bought that powered OTG cable off Amazon and it will power the Chromecast as well as provide the means to flash the Chromecast via a USB thumbdrive. When you apply power to the Chromecast, it automatically flashed the bin from the USB drive. There was no interaction required (or even possible). Of course this was on the original firmware - if your Chromecast updated itself, you have lost the ability to root the device at this time.
Clearly the Chromecast does sense the USB drive and pulls data from it during the initial boot sequence. However I'm not sure if it would ever work for other devices such as keyboards or storage devices, etc.
I'm not sure why anyone would want to hook those types of devices up to the Chromecast however. Once you have root, you can telnet into the device, so adding a keyboard doesn't seem that important. The whole idea of the device is that you send it media from other devices and control it via that other device. Adding storage for example doesn't seem important since it can pull media off the network already (ie a NAS or another computer).
Anyway. That has been my experience with it so far. It's a long winded answer to more than just your question about the OTG plug.
I would personally love the ability to send audio out without having an hdmi TV be on through the usb somehow...
Sent from my Nexus 7 using Tapatalk 4
USB Tethering not working - SGH-i997
Hi all,
i have install Avatar 7.0 to my Samsung SGH-i997 from "http://forum.xda-developers.com/showthread.php?t=2174227". it's look cool.
But when i am trying to USB Tethering, the massage shows as "Unfortunately,Setting has Stopped".
how to Fix this issue.