Hi all,
I have a Spanish Vodafone P3600. (S300). I've run into problems while updating the radio ROM and several other things.
I've managed to change the SPL, all versions, no problem. Even the hard SPL. The problem arises with almost ALL ROMS and ALL RADIO ROMS. I put the PDA in bootloader mode and I begin the updating process. Well, it stays at 0% all the time, both in PC screen and PDA screen. When I am tired of waiting (more than 30) minutes, then I have to take the battery off. The PDA goes into bootloader and I have to apply the unbrick procedure.
I have only been able to put the FAMAN 3.5 Spanish ROM (WM6) so the PDA works when I unbrick it. However, it does not have RADIO ROM and it shows "no GSM" at boot and obviously I cannot use it as a phone.
Is it broken? Why can't I flash the radio ROM? Somebody with a similar problem?
Thank you all very much in advance.
Best,
Unsolvable problem
Thanks all for the feedback. Pof was kind enough to address the problem.
I ditched the radio bootloader (not the regular bootloader) and a a result I cannot flash the radio. It seems that the phone has to be sent for repair.
"if it works... don't touch it" I should have paid attention to this
Hi, i've bough a p3600 on ebay.
The seller tell me the phone is out because he flash a bad radio version on the phone.
I try to upgrade some file. ( Rom OS, Radio, SPL,etc ...)
I try the splexploit...
BUT ... The phone already stay on startup. i can see HTC startup screen,the windows startup screen ...but never the today screen.
I try hard reset, htc official rom, cookeed rom,...but when i flash a rom with "gsm", the update freeze at 13%
I try with usb and with sdcard..same thing, already stay at 13% !
But if i flash hard spl, 100%, if i flash OS, 100%, just the radio freeze at 13%
Any idea please ?
update
after the boot, i've got a "no gsm" message near the radio version
other people got the same problem like me ...
God oli, help me please
I more or less had the same thing and solved it with the sc card flash page.
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
A rom that works for me to flash it back to the working original
http://www.allaboutphones.nl/forum/request-originele-spv-m700-rom-p3600-rom-t727.html
To download you have to register with them.
GL
Hi, updating the radio to 1.56 crashed, now I have the No gsm message and doesn't boot, running mtty from bootloader with info2 command it says supercid but I can't update any official rom SPA, WWE, ITA... the error is "vender id invalid". I've tried the sd method but returns to bootloader .
Any help will be appreciated.
You should try SSPL : http://forum.xda-developers.com/showthread.php?t=293632
And if it doesn't work the Des' Crash-Proof SPL :
http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
and try to flash a radio rom again !
doesn't work
try again and again ...the phone block at 13% ( when the radio upgrade begin) ...
pfffff
I've the same problem and after several attempts without result I sent the phone to the workshop and they told me the problem is with the main board! (this cost almost the price of phone itself). Moreover, I've seen some where here that the problem could be caused by radio chip but I couldnt get the detail.
If you find a solution give me a tip.
i've test lot of thing.
I progress with mtty. but i've got a problem ..i can't downgrade the phone under SPL 1.05.
SPL 1.04 can "reset" the radio, or enter directly to the radio bootloader. With that, i can save my phone.
Try mmty (see the wiki => bootloader info) and with the mfg spl, you can try the method.
Guys,
I've got the same problem...
I've sim and cid unlocked my spv m700 some time ago, using wonderful software from pof. Everything went smooth.
Today I've decided to update radio rom to 1.38.00.11 to enable gps.
I've launched RUU, everything was ok till 44%, when I've got message "Communication error".
After that program tried to recover rom without success, I've got another message "Image corrupted"...
I've tried to reboot my spv (both SR and HR), after rebooting I see:
M 05
B 05 D 1.23
then those symbols disappear and I see only Orange logo.
That's it... The end...
Should I reload radio rom or both rom and radio rom to my DEAD spv? If yes - how?
Please help as I'm very disappointed, frustrated and so on!
Thank you!
Update: A-A-A!!! I did it! I revived my spv! Let me explain how (I'm kinda new to all this rom and and ssl things, so forgive me for mistakes, if there are any):
1 I ran unbrick software. Yesterday it did not work (said, that could not find smth), but today it worked fine.
2 I ran RUU and BINGO! That's it!
BTW, I have vista, but it still worked (I think, thanks to Windows Mobile Device Center, which I have installed).
Also, I killed wmd process in Task manager in the beginning (have read this recommendation somewhere).
Thanks to everybody for their help!
nyco,
could you please explain briefly what you did exactly and which radio and rom you used
thanks and regards
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Thanks stepw...
when I hit task 2A nothing happens.
Original ROM doesnt respond. I flash with cooked ones. Result 100% successful. I restart the phone- hang at boot screen.
stepw said:
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Click to expand...
Click to collapse
Hi,
I'm already under the hard SPL. and "task 2A" not working.
Macars, try only with radio ripped or full original rom (from htc or cooked with radio) because some cooked rom have only OS.
Can you tell me what SPL you have?
Hard SPL?
Have you try splxploit ?
Can you tell me what rom you try oviplokos1 ?
thanks,
it shows SPL 9.99 and with this I cannot flash anything so what I do is to update with splxploit and then the phone changes to SPL 1.2 olipro. With 1.2 I can only flash coocked ROM and will go until the end 100% successful- (original ROM the phone does not respond), but when restarts with newly loaded cooked ROM the phone hangs at window login screen and when put it in bootloader the SPL 9.99 returns again.... the story goes on like this.
I'm becoming mad....
hi,
you can only flash cooked rom because the rom you flash contains only OS. When you flash HTC rom, the rom contains os+radio+spl+....other thing ...
Try this method to downgrade your SPL (9.99) to oli 3.20 :
1°) run splxploit
2°)when the phone reboot on the spl 1.20 oli, run HardSPL 3.20 olipro. (search on the wiki or the trinity forum
3°)upgrade to 3.20 oli ...
Now, when you go to the bootloader, you can see SPL 3.20 oli.
Try reflashing a radio only (see the upgrading topic, you will see radio 1.56.xxxx)
Tell me if this method work.
When i'm on spl 3.20 oli, i can load radio rom to 0%
when I downgrade my phone to spl 1.05, and i can run the upgrading to 7% (best score )
To downgrade to SPL 1.05:
edit the "unbrick.bat" on the splxploit folder.
Replace TRIN_HardSPL.nb to TRIN_SPL105.nb
try to find SPL 1.04. I'm sure if i got the spl 1.04 i can revive the phone
Did exactly as you said final result:
When i'm on spl 3.20 oli, i can load radio rom to 0% (and stays there )
hi,
ok, try to load spl 1.05 with splxploit, and when it is load, run radio upgrade (1.56.xxxx)
Try to find spl 1.04 and mtty it can be reset the radio bootloader
if you find 1.04, give me it
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
macars said:
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
Click to expand...
Click to collapse
arf :/
You got exactly the same problem i have.
did you check if you have bad block (with mtty)
try format the phone with mtty.
i contact pof, but he doesn't answer me
Hey
My first post - weee
I been reading and learning from this forum for quite some time now. And I have flash my rom a few times succesfully.
But I upgrade recently to wm 6.5 with the original rom for HTC.
Its not as good as my 6.1 rom, so i have tried to install a different ROM with wm 6.5.
My problem is that it starts ok - the tricolor screen comes and it says USB in the bottom of the screen. The screen then turns white and a status bar is shown (and on the screen of my pc as well). It says 0 % and stays there for 5 minuts or so. Then it says Error 262 and the I have take out the battery and start med phone again.
When i remove the battery and starts the phone im back to my old wm 6.5 original rom - so no harm done.
Why cant i flash my phone ?
I have tried (after reading a lot) to
- unlock the CID ?
- Hard reset
- Soft reset
- using a different rom
Am I missing something or ?
Try flashing from the card rather than PC. or from PC but take out the sdcard. Also make sure you have Hard-SPL still.
Pezzie said:
Hey
My first post - weee
I been reading and learning from this forum for quite some time now. And I have flash my rom a few times succesfully.
But I upgrade recently to wm 6.5 with the original rom for HTC.
Its not as good as my 6.1 rom, so i have tried to install a different ROM with wm 6.5.
My problem is that it starts ok - the tricolor screen comes and it says USB in the bottom of the screen. The screen then turns white and a status bar is shown (and on the screen of my pc as well). It says 0 % and stays there for 5 minuts or so. Then it says Error 262 and the I have take out the battery and start med phone again.
When i remove the battery and starts the phone im back to my old wm 6.5 original rom - so no harm done.
Why cant i flash my phone ?
I have tried (after reading a lot) to
- unlock the CID ?
- Hard reset
- Soft reset
- using a different rom
Am I missing something or ?
Click to expand...
Click to collapse
take out sd card
do hard reset
do wipe data
go to step 0 and begin with unlocker
flash stock rom
now flash rom you would like.
worst case, if you have trouble flashing it - key--combo to bootloader and flash/hardspl from there
Thx
I unlocked the phone using HARD SPL after removing the SD card and flashed it.
It works
Thx for the help.
Do you have a HardSPL? If not, then you won't be able to flash. You need to do some more reading.
shannonknable said:
Do you have a HardSPL? If not, then you won't be able to flash. You need to do some more reading.
Click to expand...
Click to collapse
YOU need to do some more reading. Specifically one post above... the OP had fixed his issue with HardSPL...
I had that problem a couple of times actually. For me, it was that my port isn't quite as tight as it used to be. (That's what she said) So I just have to make double sure that my phone doesn't move during the flashing sequence AT ALL. Otherwise the same problem will occur.
Hope this helps!
whoops same problem to me. I don't read so good when it's friday night. I stand by my advice though for future problems
hi to all.
My problem here:
Every Rom i test, become unusable in a while.
My diamond was bricked few days ago, and i received a new one by my phisical and logical damage insurance.
I'm not a noob (but not a pro )
I've always followed instruction for rom changing. hspl, radio and rom.
I was trying to test several roms, (i'm italian, i've tryed Lovers 6.5, but was slow, so i turned back to 6.1 roms).
I've tryed Kimera, and lot of italian roms. Every time that i begin to customize them (by installations of Oxios Memory, cleartemp, google maps, restore from pimbackup, changing tf3d background, facebook linking my contacts etc) every rom stuck, become slow, and for every operation take more than a minute. Many application shortcut become unavailable, and when it is impossible to reach the reset application (different application from any roms, same problem) and attempt manual reset (soft reset) it performs HARD RESET!!!
Sometimes also performing hard reset, installation batch says "installation error", or error occourred while attempting to install (application name).
First time i was thinking about a rom problem, (strange because many other users doesn't see this problem) so i've changed to another, same problem, another rom same problem, and so on.
So i try to change hspl, from 1.93 to 1.40, same things, several tryes, same problem, so i now turn to hspl 1.34...
_________________
Edit: Hspl 1.34, 1.37 (signed or not), 1.38 and 1.93 show me (in bootloader, or three-colored screen) the same message:
In the red zone
Code:
DIAM100 MFG 64M
SPL-1.40.OlinNex
MicroP-Diam (LED) v11
In the green zone
Code:
PSOC-Diam STAGE_PVT v0x32
Is this situation normal?
_________________
Now i'm testing on 1.34 hspl. If it shows another problem?
Do you think about an hardware error on diamond?
How can i solve/fix this?
Edit: Testing in 1.34 give same problem.
Any Ideas?
Please any help needed, Thanks in advance for patient in reading my bad and ugly english...
SOLVED:
Ruu i was using for Hspl flashing was not correct.
I've tryed another one and it worked.
Now on hspl 1.93 Olinex (now visible on bootloader screen)
Roms don't crash anymore (until now XD)
Thanks for attention, problem solved, now can close this thread
Hi everyone
Yesterday I got a pretty oldie device: HTC Diamond 2 - known as HTC Topaz (MDA Compact 5 - T-Mobile DE branding).
I had many HTC phones before and I loved updating my devices to custom ROMs and even I cooked one
So it's naturally that at first I wanted to apply HardSPL into my new Topaz (especially I prefer English language instead of German ). Unfortunately it was more difficult than I thought.
Always when I try to apply HardSPL ( http://forum.xda-developers.com/showthread.php?t=520312 ), update process freezes at 0%!
I found some users had exactly the same problem but I tried every suggested solutions - with no success.
My data from bootloader:
TOPA 2000 32M
SPL-1.83.0000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW
What have I tried and didn't work:
- Topaz-HardSPL_V5_09R6_CRT_183HSPL - automatic mode returns "Corrupted data", manual - stuck 0%.
- Topaz-HardSPL_V5_00R5_183HSP - as above
- HardSPL + RUU - stuck 0%
- HardSPL on SDCard - frozen at "Loading..."
- update_to_183.zip - RUU: stuck 0%
- update_to_251.zip - RUU: stuck 0%
- TopazSPLRelocker_SPL133 - I know it is an original SPL but... stuck 0%
- SSPL-Manual-TopazV5_09 - freezes device
- MTTY - I tried: format the device. But after that, I still can't apply HardSPL (cmd: task 28 55aa)
- My own cooked ROM (only original Radio + HardSPL) - stuck 0%
- I tried 3 different "RUUs" and TopazAdvanceRUU (original RUU from T-Mobile I tried too)
- Applied SPL from UK branding ROM - vender ID error
What worked:
- The newest ROM from T-Mobile DE ( RUU_Citrine_TMO_DE_2.13.111.3_radio_sign_topaz_61.42tc.25.31_4.49.25.05_ship.exe ) - I got device with this ROM but I applied it again
- SPL.nbh from ROM above has older SPL. I applied it in TopazAdvanceRUU and my device got SPL 1.78.0000 (before 1.83.0000). Full upgrade restores SPL to 1.83.0000
My only idea what can help:
Maybe the only solution is downgrade ROM. I found in Topaz wiki ROM called RUU_Citrine_TMO_DE_1.40.111.1_Radio_Signed_Topaz_61.20t.25.10_3.43.25.19_Ship.exe but links are expired. And still I'm not sure if it would work.
Do you have any idea what could help me? I spent about 10h (6h yesterday and 4h today) and I have no clue what to do
I hope someone knowns the solution for my problem!
Yes, have same problems. Need install ROM with Russian LP.
May somebody help with install hard spl for thos model?