I received a replacement handset for my Orange M700 yesteray after the other 1 was dropped and shattered. I have a minor problem in that if I try running the Trin_Unlock_v1 package (on XP) it seems to complete successfully but always hard-resets the device before running the unlock application. I ran Des SPL to flash from SD, completes successfully but after a soft reset or simply using the power button to turn device off I can no longer send sms, mms or make calls calls once turned back on again.
Has HTC or Orange altered to ROM somehow to cause this?? I have tried MARY, UDK 6.1 Full, Dopods WM6, A3XL 3.1.1 Lite and all give the same set of results.
Any help would be a bonus
Related
Hello,
Today my vibrator goes mad, so I decided to send my phone back (I still have the warranty).
In order to proceed, I have to put back the official SFR ROM, and luckily I found this link on the wiki : ftp://xda:[email protected]/Uploads/Trinity/SFR_S300+_ROM_French_1.23.163.2_Only_OS.rar
So I did a little backup of all my data, I take off the memory card, and I started the installation.
But at 9%, it bugs. Hopefully, the ROMUpdateUtility display a message that I have to put off and put in the USB cable, and retry the installation. Its seems that works, because the transfer was complete and the phone reboot automatically .
But when the phone reboot, it display the classical boot screen SFR Bonjour, show some numbers (M 05 - B 05 - D 1.23 - R 1.50.08.11 - G 32.83.7020.20h) and when this numbers disappear the phone freeze.
I've try to wait half an hour, but the SFR boot screen stay, and the phone didn't respond to anything (I've try to put the power cable, and the LED set on only if the phone is off). I have to put off the battery to turn off the phone.
If somebody could help me, please!
And excuse me if I made any mistake, english is not my native language.
I have the same issue......
I have the same issue, my SPVM700 just sits on the initial splash screen after I tried to re-flash it to the original Orange ROM [as I too had to return it for a warranty repair]. I used Mozzer's Orange ROM [http://forum.xda-developers.com/showthread.php?t=309959] to restore it - the procedure looked the same as with other ROMs I had successfully loaded but it was only when I tried to restore the official MNO ROM that my Trinity bricked.
I can access the bootloader screen [TRIN100 IPL-0.50, SPL-9.99CP] and can flash the device, where the progress bar always reaches 100% on the PC and the PDA and then the PDA automatically reboots, however, it does not advance past the splash screen.
I have tried the Hard-SPL fix [ http://forum.xda-developers.com/showthread.php?t=299659 ] and then re-flashed the device with other ROMs that I had tried previously [Schaps, AX3L, HTC Official WM5 P3600 ROM etc..] but still get no joy - is there something that I should have done prior to re-loading the original ROM that I have missed and is my Trinity now forever a brick?
you've presumably tried a hard reset? but it's not written above so i thought i'd just check.. (pressing two soft reset buttons and pushing the stylus in the reset hole?)
Yes I did try a hard reset even though I didn't expect much from it as I had just replaced the ROM [effectively wiping the ROM and replacing it with a different ROM] and none seemed to boot. Once the device has started booting up, the only way to switch it off is to disconnect the battery [and the only way to switch it back on is to soft reset] so I am guessing there is a hardware issue caused by returning the device to the Original MNO build as this was the ROM upgrade that trashed the device - other ROMs tested prior to this had loaded successfully.
Sorry to bring this back but since the link is in Behemot's sig, it is not resolved yet. Have you guys loaded SSPL before flashing? If you haven't, the OEM Rom won't boot with HardSPL. Try flashing another custom Rom and use this method before flashing the Shipped Rom.
Good luck.
ask ilos for original SFR rom or search for extenue SFR rom. or contact me by personal message and give me your mail i have the SFR ROM without radio ROM (you can get the radio on this forum)...
Sorry, I've forget to update this thread...
So, for me the only solution was to bring back the device to an SFR store (it is still under warranty).
I believed they would reproach me that the RADIO was not the original one or something like that, but no. They didn't make any remark and send my device back with an official SFR ROM.
The only thing is that they take more than a month instead of the traditional two weeks to fix it.
So all is ok for me.
I hope you will solve your problem
Hi all,
I have been visiting these forums for 2 years now and have downloaded some great tools and ROMs to enhance my Trinity, however something all of a sudden has gone very wrong!
I upgraded to WM6.1 Elegance edition about 3/4 months ago, CID unlocked the phone about a month ago and everything has been working like a dream.
However just today, I attempted to turn the volume down on my phone during a meeting (I always forget to normally!) and there was no display. After few battery resets, again no display. It starts up, loads the the Elegance splash screens and then hangs on the screen before when the OS should appear.
My decision was to flash the ROM again. I cant flash using Activesync as it wont pick up on the hung screen, so I started the bootloader and got as far as 1% of the flash and it will restart. So I tried the SD Card method when resulted in a "loading" screen appearing for a few seconds and then it goes back to the standard bootloader and displayed a 00068002 error.
I am out of ideas, I hear mtty.exe is a good program for this kind of thing, but what I want to know is if this is fixable or if I should give up!
I have been working on this since 2pm today none stop!
Can any of you guys give me any suggestions please?!?!?
Kind regards,
Jonathan
Should be a cinch
Did you SPL the Phone before flashing roms?
If you put the phone into the bootloader mode The RGB screen and kill of activesync you should be able to run one of the flash update programs.
If I have flashing problems its usually Active sync so I kill it then run the flash program.
I've got a sneaky suspision your battery might be causing the problem.
Hi there, thanks for the reply. As I was new to upgrading I havent used SPL on the phone before flashing the ROMS. I did use an unlock tool recently as i wanted to try a different network SIM to see if it worked when I was in South America, so the phone is unlocked to all networks. Are you saying if I SPL now it should sort the problem out? If so how do I do this withour ActiveSync working - can you use SD?
Another thing I failed to mention was that when I start an upgrade and it follows all the steps, it doesnt say the current ROM on the screen where you press update ROM. It just gives the name of the new ROM and the current one is left blank.
I have disabled Active Sync before attempting the update. It seems to go through fine and then the phone restarts wafter 1% of the update.
What makes you think it is the battery? I am happy to spend under 20 pound on ebay if you think it will fix the issue!
try unbrick.bat.......my trinity was also stuck.......unbrick.bat save my day....
The same happened to me several time....I could not find a solution other than this one:
1. Flash the official HTC ROM.
2. Flash the required ROM then.
it works for my TrinTy.
Hey guys,
I have two WINgs and I Hard SPLed one already and I Flash it regularly
the other one was at the T-mobile Rom and stable till it starting restarting at every call.
So i treid to Unlock it also like the other one
So I backed up all my contacts and Messeges with PimBackup
and after i Installed the three files
security removal, Aserg and cannonyang
when I try to Hard SPL through RUU with USB so it tells me no connection although its connected in Activsync
I searched the forums and Bypassed the Connection issue by entering the Boot loader through the phone and it got to 2 percent and told me i need a newer RUU although it is the Same as the other Wing for the versions and I have done the other one Fine
when I tried to do it again and still bypassed into the boot loader through the phone it now tells me that There is no Connection to the device. Although the USB sign is available in the bottom.
Now I have Also searched the forums and found Aserg suggesting that we install the Native T-mobile Rom
It connected fine and went into
1% of updating Image and then it gave me a communication Error
Now I noticed two things:
1. it Goes into Bootloader and CHills there
2. It Changed the IPL number from 4.26.0000 to 4.10.0000
but SPL remained 4.26.0002
Does any one have a Solution for this Problem Guys?
Is it bricked now and I just can't see it?
Please help because all my contacts are are on it and i am working with crappy nokia instead of it that has none of them.
you can import your contacts from PIM backup onto your other device if it has PIM also, you know that right?
Now some questions
Did you install the cabs that papamopps said to?
Can you still flash the RUU? It seems you have the newer Wing SPL but the older IPL.
I dont' know if this is the problem of onkolog rom or just the way i flash my phone.
First i use the old rom of davideuck Davideuck_V-7, CE OS 5.2.20769 on 29,March . I then got trouble with battery drained with this rom when i used SPB 3.0.
I try to update to new 6.1 rom of onkolog on 1, May
This is what i did.
My phone was on and connected to my PC. I then run HardSPL 1.56 successfully.
The phone was on again and i run the wrapper file in the same folder with onkolog rom. It run smoothly but when it recognized my O2 network it told me to be restarted after 5 seconds and when the "htc" words appear my phone hang.
i need to do a soft reset and this time it worked.
I then tried to install flip it. It required to restart after install and this time i got hang again.
I install htc Tweak and use it soft reset, some times it worked sometimes my phone hang and i need to do soft reset.
The same problem appear when i used A-A reset software.
I then decided to go back to early version of onkolog 6.1 rom (used older version of hspl) on 1-April and still got the same problem.
I tried to reflash with uspl but still stucked with usb driver.
Can anybody tell me how to show this problem . I really like the idea of onkolog but maybe he is too busy to answer me.
Hi, i have a serious problem with my diamond...if someone knows how to fix it, i will be a lot of gratefull.
I have htc diamond movistar, with cooked rom 2.0.3 - BsB 1.1, during 4 mounths, 0 problems.
Yesterday, the diamond has reset 2 times...ok...but the third was the last. It died. Not turn on...never.
I can't revive them in any way. Do not start with any of my original 2 batteries .. It does not recognize the network stream, or the PC, ActiveSync does not recognize ... soft reset and hard reset doesnt rapair anything...
It starts 1 of 50 times, and when he makes, I only can put the bootloader mode, is the only thing i can do. And the bootloader recognice the usb mode. So i should can flash...no?
To send the diamond to technical service, i have to put the original rom and hardspl, but i can´t. All times that i try to flash, the process fail.
I had try to put the original spl (1.93), and the process arrives to 100%, but after the reset, bootloader says that i have 1.24 hardspl yet !!
And when i try to put any rom, cooked or original, always fails the process at diferent percentages...15%, 26%...65%... Always the same error, [302], connection fails.
So... is difficult that the diamond turn on, the rom doesn´t work and no pass of MOVISTAR logo...the bootloader works, but all the flashings that i try, fails.
¿¿How i can put the original spl and original rom to send to technical service??
THANKSSSS!!!