Related
Im upgrading my xda11s to the latest official o2 upgrade. The problem is that it has installed the new radio version ok, but it has been stuck on 12% for about 3/4 of an hour installing the extended rom, and th pc doesn't seem to be doin anything. Can anyone give me any advice on what to do next thanx
neildunne said:
Im upgrading my xda11s to the latest official o2 upgrade. The problem is that it has installed the new radio version ok, but it has been stuck on 12% for about 3/4 of an hour installing the extended rom, and th pc doesn't seem to be doin anything. Can anyone give me any advice on what to do next thanx
Click to expand...
Click to collapse
just try again....
This happend to me and it was
an issue with my firewall.. it blocked the comunication.. I had to switch it off and start again... I think I was using zone alarm at the time.. If that helps
does anyone know why this happens?
has anyone found a workaround?
i think this rom work well... i using about one week
most modern roms take 10-15 mins to pass from 98% to 100%...so wait...and wait...and wait...
Ditto
You gots to wait!
i should still wait 15 minutes after the computer says 100%
it has been 15 minutes and still at 99% how much longer
the update utility says congratulation! wtf
20 minutes and i am almost ready to flashback?
whats the problem? what roms haved you tried updating from i,ve tried
2.26 2.3 and 3.2 rc1?
both in the computer and the wizard it stay at the same number, if the computer finished be4 then there is a problem...
Whats your IPL/SPL version number?
had the same problem,
and wasn't patient :$
now i get stuck in the boatloader :s
another upgrade isn't a go since i itz not connected
to active sync?
is there a way out :s
haha, you don't have to be connected to activesync.
Just boot it in boot loader mode and plug it in. You can flash like that.
That's actually how I do all my flashes.
I am just on bootloader ...
itz stuck there :s
any reponse
i would like to try flashing again any ideas because it didn't work the first five times.
Me too
I have a G3 T-Mobile wizard (no .001), and it stuck at 99% with the PC version saying finished. I waited 25 minutes, gave up (there is a battery issue!) and reflashed with Molski's 2.26.
how can u flash it again?
I am in bootloader and stuck there no updates work nothing :s
prestonmcafee said:
I have a G3 T-Mobile wizard (no .001), and it stuck at 99% with the PC version saying finished. I waited 25 minutes, gave up (there is a battery issue!) and reflashed with Molski's 2.26.
Click to expand...
Click to collapse
If you have .0001 then you have a G4 Wizard and NOT a G3 Wizard.
Molski
no no
molski said:
If you have .0001 then you have a G4 Wizard and NOT a G3 Wizard.
Molski
Click to expand...
Click to collapse
Yes, but I have "no .001", which should have been "no .0001".
Is your rom the same as T-Mobile 2.26 if I don't install the extended rom? (I install my own extended rom manually.)
Kartboy: As goldrush98 said, you don't have to be connected to activesync. If you see "usb" on the tri-color bootloader screen, just start the rom flash program and it will flash the new ROM. Worked for me.
please stick to topic
the topic is ell AKU 3.2 rom 99% crash not ell AKU 3.2 rom ipl/spl
i do not think the crash has to do with ipl b/c i know i have a G3
where is the developers response
Same issue here.
I have the same problem here. Mine gets to 99% on the phone and the computer says it's done. I've waited over an hour for the phone to finish.
Hi,
I wanted to update my trinity in the version of S300+ (French) with the original HTC ROM.
Not only it didn't work, but I lost my phone, I cannot access anything even with Hard Reset and battery removal...
When I want to upgrade, it's going till 1% and then it stops and I'm getting a message "Error 286" Cannot connect with phone.
I cannot hard reset, I cannot do anything! When I hard reset, I'm always coming back to the bootloader (I think it's the bootloader, the screen with colors, where it says numbers and it's says USB).
Any idea? A upgrade with miniSD will help?
Thanks!
Start flash utility again and wait untill it starts again (can take sometime).
I had it to when I first flashed a rom.
Hi,
I tried it already, but it's always blocking at 1% of progress and it's telling me in the computer Error 286, and the phone resets and comes back to the bootloader...
Any idea?
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
This will solve all your problems:
http://forum.xda-developers.com/showthread.php?t=308691
sharedworld said:
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
Click to expand...
Click to collapse
Put the phone in BOOTLOADER, then disactive ACTIVESYNC (form menu). After then start MTTY (you found it in the forum) set it on USB and then give the command:
task 32 Enter
task 28 Enter
task 2A Enter
info 8 Enter
task 8 Enter
After the last command the PDA restart and then you make a normal flash.
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
qubit76 said:
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
Click to expand...
Click to collapse
Please give more instruction howto
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
biohazard said:
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
Click to expand...
Click to collapse
SFR dosen't give any ROM... But the problem is that I cannot get out the bootloader, but I'll use the solution given here.
Thanks!
sharedworld said:
SFR dosen't give any ROM... !
Click to expand...
Click to collapse
Looks there]...and flash again
shym said:
Looks there]...and flash again
Click to expand...
Click to collapse
It's a DUMP... And not a full one... For ex. you do not get the splash screens...
Hi all,
This morning I wanted to flash the new HTC ROM.
Flashed: RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship (Succesfull)
Restore_Stock_SPL_114_2.zip (Succesfull)
But then my deviece rebooted and now it shows:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
____________________________________________________________
Blackstone_CustomRUU_v1.0
Gives me Error: 292 Invalid Vender ID
HDa4-BMCF5567-HUEbc568-BMCF55670
____________________________________________________________
I tried USPL but gives a error that deviece is not responding
I tried several spl's, nothing hard spl, nothing...
Several coocked and shipped roms nothing...
Some cases it goes to flashing screen but stays at 0%
and some cases it goed to flashing screen goes to 1% and then gives the error...
Can someone help me?
have you just tryed with mtty tool ?(it reset you doc),it works with jasjar.
babak said:
have you just tryed with mtty tool ?(it reset you doc),it works with jasjar.
Click to expand...
Click to collapse
Babak jan,
mtty khatarnak hastesh....
mikham yek lahze waysam.
EN:
Mtty is kinda dangerous,
I'ma wait for some other tips before using mtty.
xmoo said:
Hi all,
This morning I wanted to flash the new HTC ROM.
Flashed: RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship (Succesfull)
Restore_Stock_SPL_114_2.zip (Succesfull)
But then my deviece rebooted and now it shows:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
____________________________________________________________
Blackstone_CustomRUU_v1.0
Gives me Error: 292 Invalid Vender ID
HDa4-BMCF5567-HUEbc568-BMCF55670
____________________________________________________________
I tried USPL but gives a error that deviece is not responding
I tried several spl's, nothing hard spl, nothing...
Several coocked and shipped roms nothing...
Some cases it goes to flashing screen but stays at 0%
and some cases it goed to flashing screen goes to 1% and then gives the error...
Can someone help me?
Click to expand...
Click to collapse
USPL was not working for me when I needed to use it to upgrade the ROM on my touch hd.
What I did was run it on Windows XP instead of Windows Vista and the device responded.
Install ActiveSync 4.5 on Windows XP, disable USB connection in ActiveSync settings, and connect PDA to computer via USB whilst the PDA is on bootloader.
Then run USPL.
prank1 said:
USPL was not working for me when I needed to use it to upgrade the ROM on my touch hd.
What I did was run it on Windows XP instead of Windows Vista and the device responded.
Install ActiveSync 4.5 on Windows XP, disable USB connection in ActiveSync settings, and connect PDA to computer via USB whilst the PDA is on bootloader.
Then run USPL.
Click to expand...
Click to collapse
Well the first try failed.
the phone didn't get connected to xp (using vmware)
So gonna try @ home.
I'm going to try this:
No connection, wait 5 min, than put battery back and preform a HR.
xmoo said:
Well the first try failed.
the phone didn't get connected to xp (using vmware)
So gonna try @ home.
I'm going to try this:
No connection, wait 5 min, than put battery back and preform a HR.
Click to expand...
Click to collapse
This didn't help......
Gonna try the xp method when I get back 2 home
xmoo said:
This didn't help......
Gonna try the xp method when I get back 2 home
Click to expand...
Click to collapse
You tried flashing your carrier's stock ROM (if available)?
Ta
Dave
DaveShaw said:
You tried flashing your carrier's stock ROM (if available)?
Ta
Dave
Click to expand...
Click to collapse
This was unbranded.....
But going to try to flash the dutch rom.
Funny thing is sometimes it starts flashing but after 1% the screen goes black and back to home menu of bootloader.
Most of the times it just stays @ 0%
xmoo said:
This was unbranded.....
But going to try to flash the dutch rom.
Funny thing is sometimes it starts flashing but after 1% the screen goes black and back to home menu of bootloader.
Most of the times it just stays @ 0%
Click to expand...
Click to collapse
Fire up MTTY and do an "info 2". It should give you the CID of the device - try and find a matching Ship EXE for that CID.
*Instructions for MTTY are in the Kaiser Stuck in Bootloader link in my sig BTW.
Ta
Dave
DaveShaw said:
Fire up MTTY and do an "info 2". It should give you the CID of the device - try and find a matching Ship EXE for that CID.
*Instructions for MTTY are in the Kaiser Stuck in Bootloader link in my sig BTW.
Ta
Dave
Click to expand...
Click to collapse
I don't know if it is you or what else.
This time bootloader said loading.....
While loading I ran the dutch rom update.
And now it's flashing.
IT WORKS!!!!!
RUU_BlackStone_HTC_NLD_1.14.404.3_Radio_52.49a.25.26_1.09.25.14_Ship
xmoo said:
I don't know if it is you or what else.
This time bootloader said loading.....
While loading I ran the dutch rom update.
And now it's flashing.
IT WORKS!!!!!
RUU_BlackStone_HTC_NLD_1.14.404.3_Radio_52.49a.25.26_1.09.25.14_Ship
Click to expand...
Click to collapse
The dutch image must match the CID / Model on your device.
Glad it's sorted.
Dave
xmoo said:
Babak jan,
mtty khatarnak hastesh....
mikham yek lahze waysam.
EN:
Mtty is kinda dangerous,
I'ma wait for some other tips before using mtty.
Click to expand...
Click to collapse
Khosh hala ke hal shod moshkelet ham shahri
Eng: I am very pleased that you resolved
xmoo said:
Hi all,
This morning I wanted to flash the new HTC ROM.
Flashed: RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship (Succesfull)
Restore_Stock_SPL_114_2.zip (Succesfull)
But then my deviece rebooted and now it shows:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
____________________________________________________________
Blackstone_CustomRUU_v1.0
Gives me Error: 292 Invalid Vender ID
HDa4-BMCF5567-HUEbc568-BMCF55670
____________________________________________________________
I tried USPL but gives a error that deviece is not responding
I tried several spl's, nothing hard spl, nothing...
Several coocked and shipped roms nothing...
Some cases it goes to flashing screen but stays at 0%
and some cases it goed to flashing screen goes to 1% and then gives the error...
Can someone help me?
Click to expand...
Click to collapse
I have the same problem only my message reads
RUUNBH
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
Glad to read you resolved your problem however I'm stuck please help any advice would be apprecaitted
in mtty, command: set 16 0
will fix it
riz157, try flashing with the original shipped rom the device came with. i had this problem a few days ago. it took a while to work out. the shipped rom did the trick for me.
Oh man
I think I also screwed up my HD. It is stuck on Loading... screen. Won't connect to pc. Can not flash anything to it. Restores ok but after reset it shows "update rom code error,please try again" and then next screen shows Loading... for ever.
Please help me guys.....
Thanks a lot
i have the same problem, upgrade rom code error spl-1.54.0000
please can you help me
thank you
alex5552 said:
i have the same problem, upgrade rom code error spl-1.54.0000
please can you help me
thank you
Click to expand...
Click to collapse
Flash the original rom what came with ur Touch HD!
xmoo said:
Flash the original rom what came with ur Touch HD!
Click to expand...
Click to collapse
what if you dont remmember what was the original one =)
i tryed to delete the HSPL
by hardboot via SD ( LEOIMG )...
i got the same problem ...
with the message:
Upgrade ROM code error, Please Try Again.
1) i took out the SD from the Device
2) pulled out the battery 5 sec wait ...
3) put it back ... Push power button ...
4) on the exclamation mark screen ( after it loads )
5) reinstall the HSPL ...
and wm workes again ....
BUT STILL ....
how can i delete the HSPL properly and put a OWWE on my device.
Tictac0566 said ones i have : ( the original that was on my device )
Quote:
"Well, at least the ROM version is the official Hong Kong ROM for the HD2, including the Radio ROM version."
where to get the Hong Kong ROM =)
RUU_BlackStone_HTC_NLD_1.14.404.3_Radio_52.49a.25. 26_1.09.25.14_Ship
Where can I download this ROM
Rapidshare don't have it no more
Can someone upload this 4 me please
Thanks
Hi all,
please if someone can help me solve problem.
I got few days ago Touch Diamond2. It has WM6.1 ROM on it. I tried to upgrade with official ROM from htc.com to wm6.5 but it hangs on 18% with error "communication error". Phone turned on in recovery mode. After that i tried flashing with custom roms but no luck again. It hangs on HTC screen when booting and nothing happens. I flashed it back with shipped 6.1 ROM from HTCpedia and it started normal.
When i start it in boot load mode it states 1.33 Olinex SPL. Do i need to put original hardSPL before upgrading to official ROM or there is something else i am missing?
Tnx in advance
Borna_bkpdata said:
Hi all,
please if someone can help me solve problem.
I got few days ago Touch Diamond2. It has WM6.1 ROM on it. I tried to upgrade with official ROM from htc.com to wm6.5 but it hangs on 18% with error "communication error". Phone turned on in recovery mode. After that i tried flashing with custom roms but no luck again. It hangs on HTC screen when booting and nothing happens. I flashed it back with shipped 6.1 ROM from HTCpedia and it started normal.
When i start it in boot load mode it states 1.33 Olinex SPL. Do i need to put original hardSPL before upgrading to official ROM or there is something else i am missing?
Tnx in advance
Click to expand...
Click to collapse
updating your Hard-Spl to HSPL 1.83 first ! in order to flash WM 6.5 rom or custom rom
Hi and tnx for quick answer.
Just to confirm. I need to update even if I want to flash official WM6.5 rom from htc.com?
Borna_bkpdata said:
Hi and tnx for quick answer.
Just to confirm. I need to update even if I want to flash official WM6.5 rom from htc.com?
Click to expand...
Click to collapse
I think it could, try it !
Doesn't the official WM6.5 ROM update include an embedded SPL though? Although if flashing from official ROM to custom ROM or vice versa you'd definitely need to update HSPL.
netrial said:
Doesn't the official WM6.5 ROM update include an embedded SPL though? Although if flashing from official ROM to custom ROM or vice versa you'd definitely need to update HSPL.
Click to expand...
Click to collapse
Please Read Carefully the instruction for installing HSPL 1.83 or better to upgrade it to 2.51.OliNex.Make Sure U Have a internet connection on as hspl needs internet to install.