i was installing WM5 on my wizard when it gave an error at 85% and stopped. only starts in bootloader but wont install a new one. whats the solution?
thanx
Well... we'll need a little more info in order to help. What is your current ipl/spl? What ROM were you trying to upgrade to? Did you get any kind of error message when the RUU stopped?
was 2.24
and i wanted higher so i downloaded one of the O2 roms
ruu gave a "file not good for ur fon" kinda error
Well.... get into bootloader mode (press the voice button while starting the device until you get the three colored screen) and you can flash the original rom again.
Did you CID-unlock your device first? No? Read read read before flashing again. Start at the sticky.
thing is, how do i flash the fon in bootloader mode?
If you connect it to the pc it will say USB at the bottom of your device screen. You can just flash at this point. No need for activesync. If no USB appears on the screen than you're not in bootloader mode.
ruu says no connection cos it always tries to check the current version first.
Hi,
When I Flashing my ROM (CR86 THD v2.6) it stuck on 88%. What should I do?
Can Someone Help ME Please.
Thanks.
Please HELP HELP HELP!
Now when I tried to flash it again with the cr86 THD v2.5 it said
ERROR 264 : CONNECTION
ERROR [264, 274] : CONNECTION
ERROR [302~318] : UPDATE ERROR
ERROR [320~328] : INVALID COMMAND
These errors seldom occur. However, if one of these errors occur, it could not be recovered and the device had to be sent back to the customer service center. In this case, you have to flash a new ROM code...
I see you have a K-Jam, try this.
Download your original ROM from “HERE” scroll down to K-JAM to find your ROM.
Put the phone in bootloader mode and try flashing the original ROM.
if you can still set your wizard in bootloader mode, try to flash button rom on your device.
Hi, my htc hd starts with 'smart mobility R1.14.25.24
D1.59.48753' and goes to windows version 6.1 initial screen (preparing for first use), then restarts again. I checked the boot loader screen and it comes with
blac100 32m
spl -1.54.0000
microp-blackstone led v6.
I did try to do USPL v2.5, i get the message 'usb port can not be opened'.Would someone please help to get my phone working? Really appriciate any help.
Hi,
Maybe try to flash with other rom, using SD card.
valanxda said:
Hi, my htc hd starts with 'smart mobility R1.14.25.24
D1.59.48753' and goes to windows version 6.1 initial screen (preparing for first use), then restarts again. I checked the boot loader screen and it comes with
blac100 32m
spl -1.54.0000
microp-blackstone led v6.
I did try to do USPL v2.5, i get the message 'usb port can not be opened'.Would someone please help to get my phone working? Really appriciate any help.
Click to expand...
Click to collapse
Put your phone into its bootloader and try to run USPL.exe. Did you remember to disable antivirus?
Fallen Spartan said:
Put your phone into its bootloader and try to run USPL.exe. Did you remember to disable antivirus?
Click to expand...
Click to collapse
Thanks. I did disable the antivirus. still not working.
Yesterday I tried orange ROM 'OrangeUK_HTCTouchHD_1.59.61.2_Radio_52.64.25.34_1.14.25.24_Ship_phone_software', hoping it would make the phone working. The update was successful, but the same problem.
valanxda said:
Thanks. I did disable the antivirus. still not working.
Yesterday I tried orange ROM 'OrangeUK_HTCTouchHD_1.59.61.2_Radio_52.64.25.34_1.14.25.24_Ship_phone_software', hoping it would make the phone working. The update was successful, but the same problem.
Click to expand...
Click to collapse
Try to install a newer version of the HSPL.
If you can't get USPL to work, have you tried HSPL? Your using a rom based on 1.56+ so you'll need to use HSPL 1.56
I just tried HSPL. I followed the thread http://forum.xda-developers.com/showthread.php?t=505377. Flashing for dummies. When I run the first step 'HSPLWrapper_Blackstone_156OliNex', it sits on 0% for long time and finaly came up with error msg. I tried the option 'recovery', but no use. I have done a hard reset. Still same position where it started. . I'm very sad now..
valanxda said:
I just tried HSPL. I followed the thread http://forum.xda-developers.com/showthread.php?t=505377. Flashing for dummies. When I run the first step 'HSPLWrapper_Blackstone_156OliNex', it sits on 0% for long time and finaly came up with error msg. I tried the option 'recovery', but no use. I have done a hard reset. Still same position where it started. . I'm very sad now..
Click to expand...
Click to collapse
What error message do you get? There should be an error code eg 260 or 262 etc. The different errors have different meanings and different solutions to fix them.
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
valanxda said:
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
Click to expand...
Click to collapse
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
valanxda said:
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
Click to expand...
Click to collapse
Error 262 is a very common error.
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
Click to expand...
Click to collapse
Try to reboot and try to rerun a few times. If this doesn't work you will need to run the manual sspl.
Troubleshooting - manual SSPL
* Boot up your phone.
* Copy SSPL-Manual-TouchHD.exe to your phone. In a file browser on your phone browse to where you copied SSPL-Manual-TouchHD.exe and run it.
* Your phone will reboot into its bootloader and should show SPL v 1.07.OliNex.
* When it shows USB at the bottom then run HSPLWrapper_blackstone_156OilNex.exe from your computer again.
* If bootloader now shows 1.56.olinex you can then flash to your new rom.
Click to expand...
Click to collapse
When you say you tried the manual solution is this what you meant. You may need to reflash to your stock (original) rom first and then run manual sspl from there.
As this is now becoming a flashing problem, please post further responses in the Dummies Guide thread and I'll help you there. This thread will probably be closed soon.
As per post above, please post in dummies guide thread
Thread closed
Hi everyone,
I have rooted my device and everything is working fine after update to 1.29.1540.16 and my phone start getting error " Unable to charge device". I trying to get it unroot because i believe its software issue.
I download this one "RUU_M7_UL_JB_50_BrightstarUS_WWE_1.29.1540.3" and try to factory reset my phone but it got RUU Error 152 everytime.. and now my phone stuck on htc logo with 4 triangles and i have to " fastboot oem boot " everytime ( .
Anyone please help me about this please.. I want my phone back to original software like before ..
sorry my for my bad english :
Can someone please explain this picture to me, and how to fix it. I find myself trying to relock my bootloader however I get this error at part 2. Btw it works perfectly when my phone is on. But in fastboot after every plug back in it continiues to give me this message. Thank you in advance.