Hi,
I had a Vario 3 (Kaiser) and am used to the LED flashing for bluetooth, missed sms and calls etc. I upgraded to the COmapct IV last week adn i see an LED there but it never flashes - is this normal???
Any tweaks to get it working like the Vario 3 did?
any help appreciated.
Thanks
There is no led, that's light sensor.
ah right... should have checked it properly
thanks for the swift reply
Related
Hello!
I bought my T-mobile MDA VARIO G4 few months ago and now I have some problems. When I am writing Emails or SMS just suddenly keyboard locks and I am able to write message only with stylus. When this happens also all the keys on the phone freeze and after I push the main key on the front several times I get screen telling me that I have to align screen and I have to follow the mark on the screen with my stylus.
So my Wizard is becoming Magician and I don’t want that, because I bought this device in the first place because of the full keyboard.
I have two explanations for my problems:
a) Problem is in a software and I would like to upgrade the ROM, but I don’t know how or where can I get the latest ROM (as far as I know it has to be from T-mobile, because my phone is CID locked)
b) Problem is in hardware because I had once my MDA in moistures atmosphere. I work in a hotel and I had to inspect Turkish sauna once and my phone was exposed to water steam for about 10 minutes. Problem didn’t started immediately but one day later, so I am assuming that this could also be the cause for all the problems.
I would be very glad if you could help me with your advices.
I apologies for my English, I am not a native speaker.
Can I install this ROM http://www.tm-phonedownloads.com/download_manager_mda_vario.html
on my device, regarding that I have CID locked device??
Hi,
I bought a secondhand Herald a while ago, it is 4 months and came with the original invoice. I been using it for 2 weeks and whas very happy. For me a big improvement over my Qtek 9000. I encountered a few times when opening/closing the slider that the phone goes into softreset, looks like a pover interruption. But then after using it in my car with TT6 the phone froze up, a soft reset brought back life but now it does no longer respond to the touchscreen. Advice from HTC helpdesk, do a hardreset. Hard reset done and gues what...to activate windows mobile please tap the screen...Still no response. Before the hardreset the phone whas working normally except for the touchscreen, now its a brik...
I read that other people had the same, softreset while opening/closing slider, anybody any idea? Of course It has to go in for repair under warranty, but if it turns out that the P4350 is not very reliable I will sell it.
Hmm...I just realized that I posted in the wrong Herald section... if any of the
forum guys could place it in the correct section?
Yves
Hi Guys!
(Sorry for my Bad English, but im German )
I have a really annoying Problem with my HTC TyTN II !!!
My Kaiser is always pluged to the Sync- or Charge-Cable on my Desk. It's also slided up, so i can see the Display all the time.
If there is a incomming Call and i'll slide down the Kaiser, the Call will be Canceled!!!
When i unplug it from the Charge- or Sync-Cable the Phone Call will also canceled!!
I've wrote a eMail to the HTC Support 4 weeks ago, but no answer till today...
Is there a Way to solve this issue?! Maybe a Registry Hack or something?!?
Thx alot!
Greetz,
infernalshade
with the slide problem that isnt a fault as far as im aware as it happens to me (I must admit that it is a bit annoying)
Uhm OK...
Then there is no way to fix it?
I just tried to reproduce these issues with my Tilt, and I could not.
When I slid open-and-up my Tilt and then called it, I was able to slide it closed and back to normal with my phone still ringing. I then repeated the steps with it plugged into USB, and still no problem.
Are you still running a stock (unmodified) ROM? I am running a cooked WM 6.1 ROM, and that could be the solution. I only have access to 1 Tilt, so I cannot test the symptoms with a WM6 ROM.
I have the Original ROM...and i think i don't want to cook my ROM...
Uhm...now i reproduced the Problem again and now it works
Strange!
But thx for help
Hello everybody,
First, sorry if I make mistakes I'm French.
My Diamond worked perfectly, until yesterday... Now it doesn't want to ring anymore when someone calls me. It vibrates, the screen turns on, but that's all. They're is absolutly no reason, since it is obviously not in "vibrating mode" (sorry I don't know how to say in english :s)
Please help me! What can I check (for example with phm registry editor)?
Many thanks.
In the TouchFlow 3D home screen "slide" to the Settings tab, the click on "Sound". At the bottom of the screen there is a volume control. It is probably set to "0" since you get no ring signal. Change it to 80% or something
jeah, ive got the same probs, just try it like said up there, or try softkeys on the left side or just suftreset
my probs had gone as i made a softreset
Thanks but I've already checked all settings. That's why I say there is no reason it doesn't ring.
I had a similar problem running one of the cooked roms, it was fine for a few days then all of a sudden it wouldnt ring. There was still sound when I played music etc just no audio for the ring, I checked all settings too. I ended up reflashing with a different rom which solved the problem.
Many thanks wilkewhaq.
My PC died 2 days ago, that's why I'm no longer able to flash my Diamond, so I have to buy a new one, and I'll flash it -_-
I flashed with belite 0.95 yesterday, it solved the issue, but today, it starts again.. -_-
Do you think it could work (more than one day...) with an other rom? I don't think it's due to my Diamond...
Thanks.
I had a similar problem. But I changed my ring tone and later on it is working. Perhaps check 'system volume' or 'Ring volume'.
Hi,
I am new to the HTC Touch Pro. But not to XDA-Developers. I had a Blue angel and a TyTN II. But they kinda sucked, so I went over to the Touch Pro. Lets go to the point now.
I am looking for a program what makes your led stay on, Always. If you turn it off, it still should be on. I've seen that the led numbers affect the way the leds around the ring behave. I've been searching around for a program, but what should I search for? Its hard to search for. If I could have found it easily, I am very sorry. But I have been watching all around on google.
Thanks for watching this Thread,
-Armazia
=/ Is there noone who knows a program for this?
heya..yeah i'm searching for it too..because i missed it since i upgraded my raphael..i was buying the t-mobile mda touch pro when it came brandnew out. there was the possibility to configure the led for every special event like: new "mms, new sms, standby..."...it was in the system-configuration menue under "notifications".. i cant find the original base cab/rom from t-mobile (germany). i just found the updated one for the mda touch pro. so hopefully someone is finding that cab file...
-WaqihZal-
Well,do you know about some SDK for the LEDs? I want to have notification blinking in some cases also and I want to programm it myself.