Related
I was performing the radio update on my MDAIII and now he hangs in the bootloader with USB in the upper middle und 2.08 in the under middle. All resets won`t bring it back to life. If I try to reinstall the update all I get is a blank message screen (update from version to version) in my Vista. How can I get out of there.
I did everything what was stated here
The original BAUpgradeUT won`t find my device. The MAUpgradeUt_noID.exe gives me the blank screen with the update from to screen.
Drake008 said:
I was performing the radio update on my MDAIII and now he hangs in the bootloader with USB in the upper middle und 2.08 in the under middle. All resets won`t bring it back to life. If I try to reinstall the update all I get is a blank message screen (update from version to version) in my Vista. How can I get out of there.
I did everything what was stated here
The original BAUpgradeUT won`t find my device. The MAUpgradeUt_noID.exe gives me the blank screen with the update from to screen.
Click to expand...
Click to collapse
I'm using a Vista PC.
After the Radio update to 1.15 the error described above is not to go away yet.
What to do, I'm nearly in tears.
Finally I got it back but with an old Romupdate from T-Online. Is there someone who got the QTC 9090 update (latest one)
That was fast..
im glad you solved your problem.
i think someone here has it.
just post what you need and make it as a title for others to read in the digest.
Im not a expert but is vista the problem??
Most likely.
Failed MDA II flash with vista notebook
Hello everybody,
I just read this thread in hope to find a solution for my problem, which is quite similar to the one described here initially.
I got a used MDA III with T_Mobile ROM. Since I'm a customer with O2, I wanted to change the ROM to O2 as well. I followed the directions given in an other thread here (don't have the link just now) and during the flashing, the flash application suddenly had no connection to my MDA III anymore. It was securely settled in its craddle an connected to my laptop via USB. Now my MDA III is stuck in Bootloader Mode with USB v2.07 displayed on the screen.
Each retry of installing either the O2 or the T_Mobile ROM now meet with the error 101: no connection. I read here that you managed to update successfully with a vista pc. Thus I wanted to ask, how you did that since I just don't seem to find the reason for the connection failing each time.
Here is what i tried to establish connection so far:
* disabled virus scanner & firewall
* unplugged the mda III and plugged it in again. It was recognized as a new device but that didn't help the connection issue
Could you please post what you did to make the update work under vista? Help would be greatly appreciated
mda3newbie said:
Hello everybody,
I just read this thread in hope to find a solution for my problem, which is quite similar to the one described here initially.
I got a used MDA III with T_Mobile ROM. Since I'm a customer with O2, I wanted to change the ROM to O2 as well. I followed the directions given in an other thread here (don't have the link just now) and during the flashing, the flash application suddenly had no connection to my MDA III anymore. It was securely settled in its craddle an connected to my laptop via USB. Now my MDA III is stuck in Bootloader Mode with USB v2.07 displayed on the screen.
Each retry of installing either the O2 or the T_Mobile ROM now meet with the error 101: no connection. I read here that you managed to update successfully with a vista pc. Thus I wanted to ask, how you did that since I just don't seem to find the reason for the connection failing each time.
Here is what i tried to establish connection so far:
* disabled virus scanner & firewall
* unplugged the mda III and plugged it in again. It was recognized as a new device but that didn't help the connection issue
Could you please post what you did to make the update work under vista? Help would be greatly appreciated
Click to expand...
Click to collapse
Try on computer with Windows XP and kill activesynk (wcecomm.exe on taskmanager/processes)
Maybe it will work. If u cant flash O2 ROM try to use "MaUpgradeUt_noID.exe". On my Qtek 9090 allways flash using this APPS and allways work.
U can try too format device first, put it on candle and use "mtty1.42.exe". On XP, kill active sync, and open mtty1.42.exe and select port USB and put OK. Do "Enter" on command and should appear USB>. After this write Task 28. This will format all your PC. Try install SO after this. This command delete all files on PPC. I have attach files that you maybe need.
thankfor the tipp and sorry for my late reply. Since I have no XP PC available i tried the mtty1.42.exe on my vista notebook. When i run it however, it only lists com port 1-3, no usb port. Do i have to make a special configuration on vista for it to work?
Thanks in advance,
mda3newbie
mda3newbie said:
thankfor the tipp and sorry for my late reply. Since I have no XP PC available i tried the mtty1.42.exe on my vista notebook. When i run it however, it only lists com port 1-3, no usb port. Do i have to make a special configuration on vista for it to work?
Thanks in advance,
mda3newbie
Click to expand...
Click to collapse
In vista i dont know...sorry for my late reply too.... in XP u must kill ActiveSync process called wincecom.exe. in vista, maybe u have to kill the Windows Mobile Device Center....i dont know...
Dont forget, put the Qtek 9090 in Boot Loader Mode (Pressing Power Button + Record Button + Reset), maybe will appear USB and u can format the device.
If this does not work, try on Windows XP....Find a friend with Windows XP and ask him to use his PC only to do that.
Maybe somebody in forum have the Windows Vista and can help u....
Sorry my terrible english....
Sjogos said:
Try on computer with Windows XP and kill activesynk (wcecomm.exe on taskmanager/processes)
Maybe it will work. If u cant flash O2 ROM try to use "MaUpgradeUt_noID.exe". On my Qtek 9090 allways flash using this APPS and allways work.
U can try too format device first, put it on candle and use "mtty1.42.exe". On XP, kill active sync, and open mtty1.42.exe and select port USB and put OK. Do "Enter" on command and should appear USB>. After this write Task 28. This will format all your PC. Try install SO after this. This command delete all files on PPC. I have attach files that you maybe need.
Click to expand...
Click to collapse
hi guys I tried the step by step process and when im enterin( Task 28 ) then pressed Enter -
Invalid command : Task28
For a help screen, use command ? or h
does any one know where the problem is??
Try this
Downlaod the XDA IIs .exe file and run it - no need to put into USB mode
http://www.o2online.ie/wps/wcm/conn...es+&+accessories/Xda+Range/Software+upgrades/
this should reset to factory default (o2)
it runs on vista too
I am not 100% sure it will work but worth a try
diesel_dog said:
Im not a expert but is vista the problem??
Click to expand...
Click to collapse
Yes, i know my reply is late but the problem ist 100% Vista! i Tryed 2 ours with vista...then i decided to format my pc and to install XP. At the first try it worked!
DESPERATELY NEED HELP.
Every time i connect my wizard to my machine using the USB cable, i get the following message in baloon.
"One of the USB Devices attached to this computer has malfunctioned, and windows does not recognize it."
It appears as "Unknonw Device" on windows device manager.
This started happening when i changed my ROM to AMP.v2.Vanilla. Prior to that my wizard was connecting fine. I have been trying to resolve this for days now but no luck.
Following are the things i have tried.
1. Un-installed Activesync & re-installed.
2. Soft & Hard Reset the device.
3. Tried going in bootloader so that i can install my preivous rom, but the machine still doesnt recognize the device and gives the same message as mentioned above.
4. Removed all the USB controllers and re-installed in the machine.
5. Tried on different machines but same results, so its not machine specific.
6. Tried with a new cable to so its not the cable, it has to be the device.
Anyone who can help with this. I am sure i am not the only one having this trouble.
Any kind of help is appreciated. Just need to connect and go back to my preivous rom.
FYI: I am running WINXP SP2 on my machine.
ROM: 10.0.0.10
Radio: 02.69.11
Protocal: 1.1.13.30
Thanks in advance.
Nick.
You can flash in bootloaders mode,its not necessary to activesync.Get you phone in Bootloaders (tri color screen) by holding down Camers button and either Soft Reset or push Power On button,it'll go into bootloaders,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the bootloaders,its good to go and run the RUU in the Rom,it'll start to flash and upgrade.Solve the activesync problem afterwards.
Thanks for the reply mate but i have already tried that.
I went into the booloader and connected the usb. It does show USB at the screen, however my PC doesnt recognize it and the RUU doesnt run. It says to connect the device.
I am not at all worried abt the activesync. Syncing is the last thing i'll think. I just want to connect and go back to my previous rom.
Any other suggestions.
Please see attached screen shots.
This sounds like a hardware issue on your phone. I doubt this works but go to start -> settings -> connections -> usb-pc and either check or uncheck the box then close that app.
If that doesn't work Search for the thread on flashing from the miniSD card. But again, this sounds like the usb on your phone has failed.
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
hmm,
Hard reset your phone and uncheck the option 'allow network connections' or something in the phone settings...> connections...> usb to pc
This error occurs when there is an “open port error” before upgrading ,You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again. disable or stop any antivirus/firewall running or any other such program which might be hindering the flash,don't surf the net.
Kill 'WCESCOM' altogether,in the Task Manager,stopping activesync.
nick_shire said:
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
Click to expand...
Click to collapse
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
IS there a place i can get step by step process of flashing through SD card?
For all the forums, i am not able to understand anything./
Even the mtty doesnt work, it doesnt open the usb port.
No Luck as of now.....Am very desperately waiting for any Saviour....PLEASE
No other way out,except to get the freakin mini usb port repaired or replaced.
zabardast_1 said:
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
Click to expand...
Click to collapse
Dang, thats right. I forgot that on the Wizard you can only flash a previously saved rom image. Can't just flash roms like you can on the Tilt.
Yep, basically, you have to get the USB port fixed as you are stuck where you are currently at on the Wizard I'm afraid.
Thanks guys. Have given my Wizard to get the Mini USB Port changed. I have my fingers crossed. Hope it works.
What exactly happens to the mini usb port?
I am having the same problem syncing.
The phone hooks up, charges, and makes the "connected" sound when I plug it into the usb port, but NO activesync...DOH!!!
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
nick_shire said:
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
Click to expand...
Click to collapse
Dear NIce_shire,
i am having the same problem and i got it resolved just by holding and tightly pressing the mini usb in my device. Its basically the problem with mini usb port of pda (Hardware) not a software one. Get it reparied from market or do it by urself. Good Luck!
USB link?
Hi mfrazzz
I have the same problem - USB link stopped working after a Radio upgrade. Definitively not a h/w USB miniport problem. Even when I get the Wizard G3 phone into bootloader and the USB word is at the bottom in the white line, flashing ROMs does not work as the RUU reports Error message stating no USB link (BTW, ActiveSync also reports no mobile device present and doesn't connect).
Is this a bricked phone then?
Thanks.
DesperateDan
PS The set is an MDA Vario and I had successfully installed S.V.I.s Manila 4.5 Beta (IPL 1.01, SPL 1.01 shows now, but was IPL 1.01, SPL 1.06 prior to installing Manila and Radio was 1.12.10 and I upgraded it to 2.69.11 and then the bloody thing stopped working and the USB link can't be enabled again)
Dear all,
I was facing the same issue of "USB device malfunctioned" and got it resolved yesterday. Its not because of software neither coz of cable (i did changed lots of cables but faced the same issue), its just because of mini USB in device. Its working perfectly alright now, it may not be replaced even dont need replacement at all. It needs minor soldering, even you can do it by urself. Just open 4 screws at its back (two under the camera cap one is below stylus placement and 4th is on opposite side) and open it. No need to be worried about......
Regards,
Barjees
HELP PLEASE!!
Ok so i think i bricked my wizard!
I have the t-mobile MDA wm5 unlocked g3.
I've flashed it to the WM6 Rom and everything had been working well, except there was no MMS feature on the phone at all which sucked! . My girlfriend thought it would be better if she did the "windows mobile update" icon feature that was on the phone to speed up the phone....She downloaded the updates & my phone shut off!! When it rebooted everything seemed normal...
1st.
T-mobile screen
IPL 2.26
SPL 2.26
GSM 02.25.11
OS 10.1.0.811
-Then i get the green windows mobile splash screen, but after i get an error message!!
*Device Authentication*
“Device authentication failure. Please contact the product manufacturer. For reference, please provide your device ID.
3563820017905901 38000050bf3f5173”
Ive tried to boot in safe mode to try & flash my phone again but for sum reason my computer wont recognize my phone is plugged in! What do i need to do?!? Please help, any help is thankful!
is not a bricked wizard men
easy men easy... but please tell to your girl dont push everything that she dont nderstands... Everybody knows that upgrade official is only for original OS like windows XP or VISTA..
Firs of all
Put your Wizard on bootloaders mode... plug in via usb the PC Active sync wont recognize your phone.. then run the original shipped Stock ROM and then your Coocked rom...
But if the PC at the same time you place your Device on Bootloaders and plug it via USB... shows a pop up message that said Windows cant recognize your device or unknown device or something... Restart your Pc... Hard reset your PDA... and replug your Device as I said it before... if not check your USB cable maybe a broken cable failure...
IF NOT?????!!!!!!!! then Use another PC with XP!!!!!
If it still on his not reconized message you are in serious problem but your girfriend Too...
Good luck
Easy..."Device Authentication failure" is caused by your ROM. Just flashing another custom ROM and the message should go away.
I'm surprised that the chef that made your WM6 rom left the Windows Update feature in there, it was bound to crash a cooked rom, since the update service never worked properly anyway.
I'm sure flashing another rom will resolve this.
yeah, flash the rom (you might want to try WizFlo 20273 v6.1.1.3 - i'm on it, and loving it). heck, you can even do a hard reset and that would probably resolve it.
Hello!
Please I need help, i want to send my Xperia back for warranty reasons, but i can not manage to get the Stock Spl back on my Phone.
I have done the same as in the Video turturals from BioVolt
(here:
HTML:
http://forum.xda-developers.com/showthread.php?t=497511
)
I am using My Brothers Laptop, which runs on Windows Vista, because I have a Macbook.
So when I do the Steps on the HardSPL programm and finally there comes the Process bar on the Screen of the Laptop. then my X1 turns off and there comes the green-red-....-Screen, which is normal according to the video turtural. Then the phone goes to grey/white screen and says Loading....
Finally the HardSPL programm pops up an error Page where it says that it cannot connect to the PDA Phone. The Phone keeps showing the loading screen and never stops. So i removed the Battery.
I have the tmobile R1 DE ROM currently on it Because it was the Stock Rom.
Please can anybody tell me What is the Problem and how to Solve it?
Is it maybe because I am trying it with Vista and not with XP?
If yes can anybody tell me how to do it with Vista??
Thanks
lernst_07 said:
Hello!
Please I need help, i want to send my Xperia back for warranty reasons, but i can not manage to get the Stock Spl back on my Phone.
I have done the same as in the Video turturals from BioVolt
(here:
HTML:
http://forum.xda-developers.com/showthread.php?t=497511
)
I am using My Brothers Laptop, which runs on Windows Vista, because I have a Macbook.
So when I do the Steps on the HardSPL programm and finally there comes the Process bar on the Screen of the Laptop. then my X1 turns off and there comes the green-red-....-Screen, which is normal according to the video turtural. Then the phone goes to grey/white screen and says Loading....
Finally the HardSPL programm pops up an error Page where it says that it cannot connect to the PDA Phone. The Phone keeps showing the loading screen and never stops. So i removed the Battery.
I have the tmobile R1 DE ROM currently on it Because it was the Stock Rom.
Please can anybody tell me What is the Problem and how to Solve it?
Is it maybe because I am trying it with Vista and not with XP?
If yes can anybody tell me how to do it with Vista??
Thanks
Click to expand...
Click to collapse
vista is not % 100 compatible with x1.so i ll recommend you to use xp.you ll be allright.because i did in xp without problem.in the vista or mac you can install wmware and you can get virtual xp if you want.you can google for more info about wmware.good luck mate.
I've done it with vista ok:
Tips: Disconnect from internet (Shut down wifi/lan)
Turn of Windows firewall/standalone firewall
Turn off anti-virus software
remove SD card
Try to remove hard spl again
Once finished re-enable all firewall/virus stuff before you go back on the internet
Hi, I've an Ba with WM6.5 in it. But when I want to reflash it, the BA wasn't detected by my computer. I've put it into the bootloader mode, but it just shows Serial, even I've waiting for almost 2 hours. But when I boot the OS, it can connected to the PC via ActiveSync. What's going on here?? Is my BA or my cradle broken??
are you running XP if so open CTRL ALT DEL then look for wscesscom or somthing and end task and then WcessMgr OR somthing and end task and try
You should see Troubleshooting in the WIKI ~ http://forum.xda-developers.com/wiki/ActiveSync
I've done all of that, but still not working. I think it's not in the activesync, because I can connect my BA to the PC, the problem looks like in the bootloader mode.... It just standing there shows "serial" and "V2.07", even I've connect it to the USB port... Any ideas??
Is there are any possibility I can repair my bootloader (if it's really broken)??, or Can I reflash my BA with other way around?? Without using the bootloader maybe??
UPDATE:
Later, I think I began to recognize the problem...
In every tutorial for Win7 that I read (this tutorial and d-two's tutorial), I was ask to update the driver of "Microsoft USB Sync". But in my case, that "Microsoft USB Sync" wasn't shown. I think it's because I haven't sync my BA with the PC yet (I've just reinstall my Windows, so all of the setting is gone). If you sync your BA, you will get the "Microsoft USB Sync" on your device manager.
But now, the problem is, I can't sync my BA with the PC, because of error in my PIM (Contact, Calendar, Task, Phone, Messages, etc). I only able to explore my devices through ActiveSync/Windows Mobile Device Center, not synchronize it. Even my ActiveSync/WMDC shows an error on the connection. So, I can't update/install the driver for "Microsoft USB Sync", because my BA have an error connection with the PC. Any ideas to solve it??
And would cloning method worked for my devices?? I mean, I get a cloning from another BA, install it in my BA, and then repeat the reflash process with my preferred ROM??
Please, need help over here....
try a hard reset
Broken Power Switch ...
Dear experts,
My device is PDA2K, last week i did upgrad from original windows to WM6.5 Pro_QVGA, Radio 1.12.00 ...... but the power switch is broken
..... as your experience how did that happened!!!! it was on cradle connected to WinXP, but since that day i'm trying to do flashing to install another Windows ...... i failed ...
Please Please Please .... Help me to do flashing or formating from pc or sd card ... because i'll never get into bootloader in my life.
Thank you ...