Related
hello couple weeks ago i found htc s730 in Norway but the phone have password
when i turn it on it says :
Password
denne enheten er last. Skviv inn enhetspassordet, og klikker du meny> Avbryt fot du slar nummeret.
My question is : is it possible to "unlock it" or mayby i have to install new ROM?
thanks for all your help
You found the phone just laying around? The owner who lost the phone probably locked it.
I would do a hard reset of it to wipe the data and start over. If theres any information you can see or use on it to return it to the person missing it that would be good. Otherwise hard reset and enjoy.
yes i found it on sidewalk with empty battery and without any simcard
ok. but i have no idea how to do this.
can somebody tell me how to do the hard reset s730 ?
thanx 4 all ya comments
...
Everything works fine
restart to the factory settings hepls awesome.
thank U once again
Cant do hard reset ..
i have the same problem..
not that i have found a phone but that it has pasword on it and they person who has the phone cant remember the password..
we would loove to do the hard reset.. but it doesnt work..
holding down the two soft buttons and then holding down power button for 1 sec.. it does nothing at all...
anyway else to do it ?
remeber,, i cant get into the menus due to the password..
The sequence of pushing and holding down is key to success:
1.) switch off
2.) push and hold l+r softkey
3.) switch on (no long push, just normal - but keep L+R pushed)
4.) wait for the prompt for reset
5.) release keys
6.) follow instructions on screen (could be "press 0 to ...")
QHelmer said:
i have the same problem..
not that i have found a phone but that it has pasword on it and they person who has the phone cant remember the password..
we would loove to do the hard reset.. but it doesnt work..
holding down the two soft buttons and then holding down power button for 1 sec.. it does nothing at all...
anyway else to do it ?
remeber,, i cant get into the menus due to the password..
Click to expand...
Click to collapse
HTC Wings S730 Soft reset
Restarting your Phone
Restart your phone when a program is not performing properly or the phone is not responding to any keypresses.
To restart the phone
1.Remove the battery.
2.Wait for three seconds, then reinsert the battery and turn on your phone.
WARNING! If the phone is restarted while a program is running, unsaved work will be lost.
HTC Wings S730 Hard reset
Press and hold both soft buttons + press POWER button for 1 sec.
Resetting your Phone
Resetting your phone will remove all the data from its memory and restore the phone back to the factory default settings.
Important If Encrypt files placed on storage cards is or was enabled before, then backup all files from the storage card before using Clear Storage, performing a hard reset, or updating the ROM system software. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.
WARNING! All your data will be deleted, it is recommended that you back up your data first before resetting your phone.
To reset your phone
1.Click Start > Expert > Clear Storage.
2.Follow the on-screen instructions to reset the phone. The phone will restart after it has been reset.
thank you Tobbie and Hakim Rahman for trying to help..
but it doesnt work..
it just boots the phone.. then asks for the security code for the phone..
Then the softkeys seem not to work ok. They are used very often and usually are the first to quit their duty. They will not work in the applications later as well, so possibly this is the reason why it was lost.
Another idea (not sure if THAT works): slide out the qwerty-keyboard and use these softkeys for the excercise, maybe that works?
A definite way to come to a hard reset is to put a new ROM on the phone. It will however only work if the phone is either CID unlocked (permanently with SuperCID or temporarily with GoldCard) or you have the original CID matching ROM update at hand.
Go to http://www.shipped-roms.com/index.php?category=windows mobile&model=Wings and pick one that fits.
Then perform a normal upgrade. If that is not possible due to the locked phone, put it in bootloader mode first:
- push and hold camera key
- switch on or insert USB cable
-> you should see 3 colour screen
From there you can start the ROM Update.
QHelmer said:
thank you Tobbie and Hakim Rahman for trying to help..
but it doesnt work..
it just boots the phone.. then asks for the security code for the phone..
Click to expand...
Click to collapse
I think you need upgrade SPL to HardSPL...
This look at the Threads of Jockyw2001 :
Wings SSPL and HardSPL
--------------------------------------------------------------------------------
The attached SSPL and HardSPL are based on the Wings MFG SPL v0.91
- download the attached files
- REMOVE SIM and SD CARDS !!
- connect usb cable
- create a SPL backup by running spl-backup.bat from SPL-backup-kit (make sure you Wings is "application unlocked", run the attached SDA_ApplicationUnlock on PC)
- copy sspl-0.91-wings.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you only want to test the sspl try flashing the attached splash screen by running CustomRUU.exe from flash-splash-wings
- you can now flash the hardspl-0.91-wings.nbh by running CustomRUU.exe from flash-hardspl-wings
- after installing the uspl or hardspl you can flash any rom, cooked rom, radio or splash screen
Note:
The HardSPL is never overwritten which in case of flashing trouble is a great insurance. Should you want to flash another SPL or USPL you must run the SSPL.
Features:
SuperCID / Security Level=0
Does not check NBH signatures
Based on 0.91 MFG bootloader, rtask, fat2sd, sd2fat enabled
Accept any password
Model ID check only 4 chars
SPL overwrite DISABLED (to bypass, use sspl-0.91-wings.exe)
Bypasses "Task 2A" (this formats entire flash which renders your Wings into a brick, we don't want that)
Important:
Use at your own risk! I'm not responsible for any damage to your device caused by using the attached files
Hi Hakim Raman,
...the suggested procedure will not work as you must have access to the device first for application unlock and executing applications. This is only an optional procedure if the poor guy wants to play with custom ROMs later. One step after the other...
I have a problem and I've search the forums and search google and I find people with somewhat of the same situation im in... but the methods to fix them don't work.
My problem is,
I have a T-Mobile WING (Herald)
I am flashed on soft SPL with SPL 4.70.Yang
I am ROM flashed to Touch-It WM6.1
I want to flash back to the stock T-Mobile Rom
I run the Stock RUU and it enters the bootloader and at 1% the wing resets
I then get a connection error 260 and the flash will not proceed.
I have tryed restarting my device/computer. unplugging my usb putting in another slot... and still nothing. Any help would be appreciated I'm really unhappy with Touch-It and want to go back to stock and do some customization that way.
you need to extract the .nbh file from the stock rom using 7-zip or winrar on the ruu executable. Make sure you don't extract the spl.nbh file. I think the file you want is something like RUU_signed.nbh
then put it into your HardSPL folder and flash away
Yep. Besides, 4.70.Yang is a HardSPL, not a softspl. If you want the SPL to also return back to stock for warranty issues, then just use USPL along with the tmobile NBH. If not, do what fzzyrn said for the best results.
Got to this thread:http://forum.xda-developers.com/showthread.php?t=421304
Go to post #2 and download the Herald-USPL-beta3
extract the nbh file from your rom and place it in the ruu folder that is located in the flash center folder.
run the utility.
spacemonkey333 said:
Got to this thread:http://forum.xda-developers.com/showthread.php?t=421304
Go to post #2 and download the Herald-USPL-beta3
extract the nbh file from your rom and place it in the ruu folder that is located in the flash center folder.
run the utility.
Click to expand...
Click to collapse
And that links to this.
My T-mobile Dash 620
I HAVE THE SAME PROBLEM . I WAS UPDATIND THE ROM OF MY 620 WITH HTC_S620_WWE_BT_3.66.424.1_4.1.13.44_02.94.90_Ship AND THE PHONE RESTART ADN WHEN THE PROCCESS GOT 25% POP UP A MESSAGE ERROR 260 AND IT WAS RECOMMENDING ME UNPLUG THE USB CABLE AND REMOVE THE BATTERY AND CONNECT IT AGAING SO. I TRIED HARD RESET AND IT DOESNT CONNECT THRU ACTIVESYNC AND ITS STUCK AT THE BOOTLOADER SCREEN (HTC). I TRIED REFLASHING RADIO AND NOTHING WORKS. PLEASE HELP ME. I BROKE MY PHONE.
ROMEROPOLACO said:
I HAVE THE SAME PROBLEM . I WAS UPDATIND THE ROM OF MY 620 WITH HTC_S620_WWE_BT_3.66.424.1_4.1.13.44_02.94.90_Ship AND THE PHONE RESTART ADN WHEN THE PROCCESS GOT 25% POP UP A MESSAGE ERROR 260 AND IT WAS RECOMMENDING ME UNPLUG THE USB CABLE AND REMOVE THE BATTERY AND CONNECT IT AGAING SO. I TRIED HARD RESET AND IT DOESNT CONNECT THRU ACTIVESYNC AND ITS STUCK AT THE BOOTLOADER SCREEN (HTC). I TRIED REFLASHING RADIO AND NOTHING WORKS. PLEASE HELP ME. I BROKE MY PHONE.
Click to expand...
Click to collapse
The S620 is not a herald and every phone is different, so I'm not sure if we could help you out. Does your phone have a HardSPL? Have you used HardSPL before? Even if the activesync icon doesn't start trying to sync it doesn't mean that it's not connected, it just means that it has nothing to sync (since it's in bootloader mode.)
I FIXED
I Did These Steps:
I Turned My Phone Off
I Pressed The Camera Icon Button
I Turned The Phone On (no Loose The Camera Button)
It Got Into Boot Mode
I Plugged To The Usb Cable
I Oppenned The Ruu For My Phone Version
And Wowla Fixed
Thank You Guys For Your Help
The Answer is in a Careful Search
This post is being made to you about... a month too late. But that's because I just got the Wing yesterday and started trying out roms today. Anyway, ran into the same problem earlier today and found the answer in the forums. I've written the following for those who might need all the steps. In your case, read from step 3. Anyway, in case you still have this problem, here's what you do:
1. Hold camera button when pressing the soft reset to get into the bootloader; it should be in red blue green and white. something like that.
2. Connect the usb to the computer and run the stock RUU Utility (this can be found on the official t-mobile website. look under something like support/downloads for the Tmobile Wing)
3. When it hits the 1%, the phone will automatically restart. When it does this, it breaks the connection between the computer and the phone. At that instant, hold the camera button and the soft reset button. Then, when you let go of the reset button, it should go back to boot loader.
4. At this point, the Rom Utility should give you the error. Do not take out the battery as instructed. Just disconnect the usb, reconnect the usb, wait for the computer to recognize it (it should appear in my computer) and then just continue the utility.
Good luck. =)
i had the same problem flashing my P4350 yesterday. tried a lot of different things, the solution for me was:
1. start flashing from the bootloader
2. just to hold the camera button when the phone restarted after 1% (nothing else, no soft reset or anything).
this resulted in the phone restarting in bootloader again, and after that it just resumed upgrading the rom.
koekiemonster said:
i had the same problem flashing my P4350 yesterday. tried a lot of different things, the solution for me was:
1. start flashing from the bootloader
2. just to hold the camera button when the phone restarted after 1% (nothing else, no soft reset or anything).
this resulted in the phone restarting in bootloader again, and after that it just resumed upgrading the rom.
Click to expand...
Click to collapse
This one works for me. Thx!
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
...........See my post below, Please. I am still having the problem stated below.
I have installed hard spl unsigned. And i have downloaded this rom....
showthread.php?t=506533 (cant post links)
I have put the .nbh file within the internal SD of my Diamond. I press volume down and soft reset and it enters bootloader but i do not get the chance to install the rom?
How can i get this to work i have been searching on here and google and tried everything but with no luck.
Thank you.
read this ?
http://forum.xda-developers.com/showthread.php?p=5244284
Thank you for the reply, I did read and use before hand and again after.
I went to the other method but it kept sticking at 0% i think it was due to the spl being signed or not.
I am now trying to do it through copying the nbh file over (named correctly and in the right location) pressing volume down back and soft reset button.... but i have a problem. It gets stuck saying 'Loading...'
Anyone know what is up with this?
Problem now fixed
Hi everybody,
I've tried to install the new Rom6.5 from christian, but first, I have to do an Hard SPL.
I've followed these steps:
step by step:
- this is ONLY for warranty reasons. i.e. the device needs repair and you have to send it to htc to get it serviced. if you plan to restore hardspl then don't even bother flashing this stock package, unless you are some kind of hacker/dev
- IMPORTANT: be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
- now the steps
1. download the stock spl package from this post.
2. download X1_HardSPL_v1 too, from this post.
3. run the hardspl package, but do not press Next button i.e do not go ahead with flash yet.
4. at this point, take the extracted stock SPL, a RUU_Signed.NBH file, and overwrite the other RUU_Signed.NBH in hardspl package.
5. go on with the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to tricolour screen with 0.52.OliNex version), it goes to 100%, reboots, done.
+1. to verify, enter bootloader (see description above in this post), and check version number on tricolour screen. it should say 0.72.0000.
I've replced the .nbh file, but my phone still stands on 0%
on my computer is says ERROR[262]
When i choose the readme it says:
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
What does it actually mean, and what do I have to do now?
I have the original windows 6.1 on my Xperia, but I have the 'aligment problem'.
I need to align for more than an hour, and if I'm lucky....it goes on...but if not...maybe I have to align the *** thing another hour.
I've tried do to an hard, and soft reset. (hold down the little button on the back and push both silver keys on the front. and I've tried to hold the volume down while pressing the on/off button.
Who can help me?
If you can react in dutch, thats even better...
If not...Well...my english is not thát bad so....
Thank for advanced....
smokingred82 said:
Hi everybody,
I've tried to install the new Rom6.5 from christian, but first, I have to do an Hard SPL.
I've followed these steps:
step by step:
- this is ONLY for warranty reasons. i.e. the device needs repair and you have to send it to htc to get it serviced. if you plan to restore hardspl then don't even bother flashing this stock package, unless you are some kind of hacker/dev
- IMPORTANT: be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
- now the steps
1. download the stock spl package from this post.
2. download X1_HardSPL_v1 too, from this post.
3. run the hardspl package, but do not press Next button i.e do not go ahead with flash yet.
4. at this point, take the extracted stock SPL, a RUU_Signed.NBH file, and overwrite the other RUU_Signed.NBH in hardspl package.
5. go on with the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to tricolour screen with 0.52.OliNex version), it goes to 100%, reboots, done.
+1. to verify, enter bootloader (see description above in this post), and check version number on tricolour screen. it should say 0.72.0000.
I've replced the .nbh file, but my phone still stands on 0%
on my computer is says ERROR[262]
When i choose the readme it says:
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
What does it actually mean, and what do I have to do now?
I have the original windows 6.1 on my Xperia, but I have the 'aligment problem'.
I need to align for more than an hour, and if I'm lucky....it goes on...but if not...maybe I have to align the *** thing another hour.
I've tried do to an hard, and soft reset. (hold down the little button on the back and push both silver keys on the front. and I've tried to hold the volume down while pressing the on/off button.
Who can help me?
If you can react in dutch, thats even better...
If not...Well...my english is not thát bad so....
Thank for advanced....
Click to expand...
Click to collapse
I would advice on reading this thread, but start at the beginning
restoring stock rom/stock spl is when you want to get back from customization for warranty reasons so I guess you started at the wrong end