I Cook roms so I flash about 15 or 20 times a day. I have a problem suddenly where my TP wont flash.
I get into bootloader and GET USB at the bottom
SPL-0.85.Olinex on the top which mean all should be ok but when i flash it gets stuck on 0 persent
I tried a stock rom, I tried Task 29 flash ...all does the same.
I tried flashing via sd card but it gets stuck on Loading
I tried mtty and did task 28/9 set etc etc and that still works but nothing else
Any ideas?
Its a GSM Rhodium 100 By the way
Grumps said:
I Cook roms so I flash about 15 or 20 times a day. I have a problem suddenly where my TP wont flash.
I get into bootloader and GET USB at the bottom
SPL-0.85.Olinex on the top which mean all should be ok but when i flash it gets stuck on 0 persent
I tried a stock rom, I tried Task 29 flash ...all does the same.
I tried flashing via sd card but it gets stuck on Loading
I tried mtty and did task 28/9 set etc etc and that still works but nothing else
Any ideas?
Its a GSM Rhodium 100 By the way
Click to expand...
Click to collapse
I was doing this while working on my version of the new AT&T ROM and started seeing WIERD issues like it would flash then when it loaded it would say a file was missing. Soft reset and it wouldnt say that but 10 minutes later it would act up again.
I thought I had a brick and was about to call warranty return and flash back to stock. I did the stock flash first (the new one that I was building mine from) and I havent had a problem since. I then put back my modded ROM and have reflashed another 50 times with no problems. That was in Aug.
Grumps said:
I Cook roms so I flash about 15 or 20 times a day. I have a problem suddenly where my TP wont flash.
I get into bootloader and GET USB at the bottom
SPL-0.85.Olinex on the top which mean all should be ok but when i flash it gets stuck on 0 persent
I tried a stock rom, I tried Task 29 flash ...all does the same.
I tried flashing via sd card but it gets stuck on Loading
I tried mtty and did task 28/9 set etc etc and that still works but nothing else
Any ideas?
Its a GSM Rhodium 100 By the way
Click to expand...
Click to collapse
Have you tried on a different PC maybe? I hope you get this sorted out dude, good luck!
hx4700 Killer said:
I was doing this while working on my version of the new AT&T ROM and started seeing WIERD issues like it would flash then when it loaded it would say a file was missing. Soft reset and it wouldnt say that but 10 minutes later it would act up again.
I thought I had a brick and was about to call warranty return and flash back to stock. I did the stock flash first (the new one that I was building mine from) and I havent had a problem since. I then put back my modded ROM and have reflashed another 50 times with no problems. That was in Aug.
Click to expand...
Click to collapse
I was getting the same problems the las week or so a few times it was doing this where it got stuck on 0% but i would just reste and it would work but now its dead. i tried our stock rom in SA and tried from TMUS and ATT but nothing would take. I PM'd oli and cmonex. MAybe they know sumting about mtty that we dont.
seeM_ZA said:
Have you tried on a different PC maybe? I hope you get this sorted out dude, good luck!
Click to expand...
Click to collapse
Jip tried two other one my home pc with Win 7 and my chicks laptop with xp as well but nothing...
The odd thing is that when i switch it off and put it on charge and i unplug it from the charger the orange charge light stays on
check if your windows have automatic updates recently? i posted in your romthread and then made a search to try help you out love you are using threaded e-mail and need your updates , i read some had issues back in the blackstone forum that their usb drivers updated and then had same issue as you, so one remotley possible issue could be your usb drivers somehow mysteriously changed.
but i am not sure just trying to help
mtty output with casrd inserted
set 14 0
HTCST ÚÈÒHTCE
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 321
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
Network ID is 0xFFFFFFFF
Other SKU
Card inserted
SD clk rate 19MHz
Cmd5 CMD_TIMEOUT
SD clk rate 144KHZ
SD 2.0 HC card
TURBO mode : SD Clk rate 24 MHz
SD Init OK
SDFATChkConf: RhOpenFile() failed RHODCONF.txt
hmmhmm1222 said:
check if your windows have automatic updates recently? i posted in your romthread and then made a search to try help you out love you are using threaded e-mail and need your updates , i read some had issues back in the blackstone forum that their usb drivers updated and then had same issue as you, so one remotley possible issue could be your usb drivers somehow mysteriously changed.
but i am not sure just trying to help
Click to expand...
Click to collapse
Ok ill try thanx. surely it should flash with sd card as well
surley it would... but i find sd card method works sometimeson some roms and other times not, not sure why tho
Nope
No drivers or anything was updated. So thats not the problem
Dammit surely someone must know.
Goin to bed now will try more tomorrow
thx anyways guys
Grumps said:
I Cook roms so I flash about 15 or 20 times a day. I have a problem suddenly where my TP wont flash.
I get into bootloader and GET USB at the bottom
SPL-0.85.Olinex on the top which mean all should be ok but when i flash it gets stuck on 0 persent
I tried a stock rom, I tried Task 29 flash ...all does the same.
I tried flashing via sd card but it gets stuck on Loading
I tried mtty and did task 28/9 set etc etc and that still works but nothing else
Any ideas?
Its a GSM Rhodium 100 By the way
Click to expand...
Click to collapse
Yes it is, move alone now.
PPL nothing to see here!
Is there a way in mtty to replace the spl maybe with file upload or something so i can get it repaired under warranty
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: Rhodium, Bootloader Version : 0.85.OliNex
Built at: Jun 23 2009 17:31:14
Copyright (c) 1998-2006 High Tech Computer Corporation
Board ID=0x80
CPU ID=0x4117B362
TURBO HW =1
TURBO SW =1
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_kby00n00hm
DEVICE ID=0xBC
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x1000
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 21 (0x15) is reversed block
BLOCK 22 (0x16) is reversed block
BLOCK 23 (0x17) is reversed block
BLOCK 24 (0x18) is reversed block
BLOCK 25 (0x19) is reversed block
BLOCK 26 (0x1A) is reversed block
BLOCK 27 (0x1B) is reversed block
BLOCK 28 (0x1C) is reversed block
BLOCK 29 (0x1D) is reversed block
BLOCK 30 (0x1E) is reversed block
BLOCK 31 (0x1F) is reversed block
BLOCK 32 (0x20) is reversed block
BLOCK 127 (0x7F) is bad block
OS NOT FOUND !!!
There is a way to flash the stock SPL via SD card. Check out the HardSPL thread and a search should find it.
steviewevie said:
There is a way to flash the stock SPL via SD card. Check out the HardSPL thread and a search should find it.
Click to expand...
Click to collapse
I tried that as well. Stays stuck on loading. Will try some more maybe it will come right
I am having the same problem with my Rhodium. Heres what i get from mtty:
set 14 0
HTCST ÚÈÒHTCE
Cmd>task 29
Format BINFS start
CE start start block=321, total block=3775
ERASE block 2778 FAIL !!!
Write 0xFF start page=0x5040, total page=0x3AFC0
Format BINFS end
Cmd>task 8
Cmd>
I have been trying for hours and hours mtty task 29 and reset and try to load ROM, it still is not working...........
Maybe maybe not
I found a guy close to my office who says he has some flashing software he bought. he reckons he can flash it abck to stock like it came from the factory. Says it will take about 45 minutes cause if it doesnt work he has to open the phone and bridge ic's or something and then flash it. says i can watch him do it. Will charge me 35$ if he gets it right. Will go there in the morning and try and get it sorted. Maybe i can get the software from him somehow. Will let you know
Grumps said:
I found a guy close to my office who says he has some flashing software he bought. he reckons he can flash it abck to stock like it came from the factory. Says it will take about 45 minutes cause if it doesnt work he has to open the phone and bridge ic's or something and then flash it. says i can watch him do it. Will charge me 35$ if he gets it right. Will go there in the morning and try and get it sorted. Maybe i can get the software from him somehow. Will let you know
Click to expand...
Click to collapse
Umm, good luck with that
Yeah, keep us updated on that please...
Right now, mine is stuck on an infinite loop. It wont turn on without being plugged in. When plugged in, I still cant turn it on with the Hardware buttons, but it shows the orange light like its charging. About 5 mins later, it shows the Touch Pro 2 screen, then shuts itself back off. Over and over.
Related
Sorry guys, i'm really new at this. Please be gentle
Ok... here's my problem...
I've tried to install Hard-SPL on my tilt but all i got is the phone resets itself. Everytime i've tried to do it, it does the same thing so I quit. Earlier this week, when I took out my SD card the phone crashed into the Tri-color screen and would not come out of it. I've tried resetting it a lot of times, still fail and no luck. I couldn't get it to hard reset. Don't know why. As far as I know all the rom and radio are AT&T's. Is there a way for me to get it out of this screen? can i still flash it with a different rom, or am i just S.O.L? I've tried the MTTY but I don't think i know what i'm doing. Please help. thank you.
did you try taking out the battery for 3 seconds?
Yes, I left the battery out for about an hour b/c i got so fed up with the screen. Still the same result. I've also tried taking out the SIM and pwr up with out it. Same result. that damn screen is horrible. coulnt' get rid of it.
bacuy82 said:
Sorry guys, i'm really new at this. Please be gentle
Ok... here's my problem...
I've tried to install Hard-SPL on my tilt but all i got is the phone resets itself. Everytime i've tried to do it, it does the same thing so I quit. Earlier this week, when I took out my SD card the phone crashed into the Tri-color screen and would not come out of it.
Click to expand...
Click to collapse
What is wrote in the tricolor screen bottom? USB or Serial?
And do not ever try to mess up with MTTY if you are not 100% sure of what you are doing!
It says Serial when it's not plugged in. USB when it's plugged into the computer. I have windows vista, so i did that whole picture tutorial on how to get the activsync/wmdc driver thing installed. dunno if that will get anywhere. Didn't get far with MTTY anyways, all i get is a cmd error. that was a good point to stop.
I would download a compatible ROM and KaiserUnlocker which can be found here....http://forum.xda-developers.com/showthread.php?t=375583
With your phone in the tri-color screen and connected to the computer run KaiserUnlocker and click on Flash Hard-SPL when it is done exit the application and install the new ROM that you have downloaded. Phone should work after that.
Please, if you're stuck in tri-color, don't flash anything. Don't listem to anyone with 30 posts, etc.
What you want to do is find the reason it's happening, so you don't do something that will make the situation permanent. Search the forums, or look at my posts by clicking on my name & you will see that I know what I speak of.
Find me on MSN/Live Messenger tomorrow & I'll help you diagnose & fix the issue.
It's never wise to cross your fingers & start flashing things, especially unlockers which require radio flashes.
First i like to say thanks to those who replied... a lil quick update...
After i let the phone sit without power for a couple of days, i tried to turn it on this morning without the sim card, it turned on, booted up and everything then after a few minutes i press the power button to take it out of sleep mode, the phone restarted it self and boot like normal again. After like 15 minutes, the phone then went back into bootloader tri/quad color screen again. I took the battery and left out for a few minutes, put it back in turn it on, it goes right into bootloader tri/quad color screen again. Something new, there's also a quick flash of a "loading" white screen then back into the color screen.All done without sim card. I think my phone is a lil bit haunted. what do you guys say?
the phone now goes back between tri color screen and booting up all the way.
bacuy82 said:
First i like to say thanks to those who replied... a lil quick update...
After i let the phone sit without power for a couple of days, i tried to turn it on this morning without the sim card, it turned on, booted up and everything then after a few minutes i press the power button to take it out of sleep mode, the phone restarted it self and boot like normal again. After like 15 minutes, the phone then went back into bootloader tri/quad color screen again. I took the battery and left out for a few minutes, put it back in turn it on, it goes right into bootloader tri/quad color screen again. Something new, there's also a quick flash of a "loading" white screen then back into the color screen.All done without sim card. I think my phone is a lil bit haunted. what do you guys say?
the phone now goes back between tri color screen and booting up all the way.
Click to expand...
Click to collapse
I say you stop where you're at and do what GSLEON tells you.
Form the sounds of it, I'd imagine it shows RUUNBH on the screen, correct?
Anyway, if that is the case, let me know & I'll help you fix it in less than 5 minutes.
This is what's displayed on the screen and nothing else.
KAIS1*0
SPL-1.93.0000
CPLD-8
and SERIAL in the white color region.
I've tried to installed HARDSPL on it but it was not successful. All i got when i tried to get installed is the phone resets itself. Have not tried JUMPSPL or anything like that. MTTY got cmd error which is a good thing. I stop at that. thanks.
You have spl 1.93. That is a troublsome SPL indeed. Using MTTY try issuing the following commands. (BTW, the boot command is invalid with 1.93 SPL as are several others)
Set flow control to RTS/CTS & connect to device via usb port using MTTY.
Hit enter until the "cmd>" prompt appears.
Enter command as follows: cmd>info 8
Post the results.
Everybody starts out sometime, my post count really shouldn't matter, but it does obviously. What I wrote was a SUGGESTION. The reason I suggested it was because obviously he was running Hard-SPL for a reason you don't just run it and do nothing else. I never suggested flashing the Radio as you would have to flash back a new one. Yes there is an option to flash the radio but you do NOT have to flash the radio as I simply suggested using it for the Hard-SPL. Hard-SPL never finished correctly probably because he is running Vista operating system, I too am running Vista, the suggestion I gave IS worth a shot because it works on Vista without changing the drivers to XP. If he wants his phone back the way it was out of the box I would suggest going here.............http://www.htc.com/us/faq_product.aspx........Select your phone model, go to software downloads, scroll to the bottom of the page and download the latest rom.
Hey sorry to butt in here, but i have been having the same issue, here are my info 8 results... any info greatly appreciated..
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 678 (0x2A6) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x9E40
Partition[3], type=0x4, start=0xAB80, total=0x10740
CE Total Length(with sector info) = 0x5615C00
CE CheckSum Length(without sector info) = 0x55C0000
thanks again
nevermind, found in another thread....
started MTTY
ran commands...
cmd>set 16 0
cmd>task 8
phone reset and started normally.
cweems said:
nevermind, found in another thread....
started MTTY
ran commands...
cmd>set 16 0
cmd>task 8
phone reset and started normally.
Click to expand...
Click to collapse
Somebody searched and found the answer!!!
I didn't think it was possible in the Kaiser Forums. Bravo good sir. Bravo
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AllTheWay said:
Somebody searched and found the answer!!!
I didn't think it was possible in the Kaiser Forums. Bravo good sir. Bravo
Click to expand...
Click to collapse
good job ATW
GSLEON3 said:
You have spl 1.93. That is a troublsome SPL indeed. Using MTTY try issuing the following commands. (BTW, the boot command is invalid with 1.93 SPL as are several others)
Set flow control to RTS/CTS & connect to device via usb port using MTTY.
Hit enter until the "cmd>" prompt appears.
Enter command as follows: cmd>info 8
Post the results.
Click to expand...
Click to collapse
Well, I have another problem. I got the message saying USB port can't be opened or something like that through MTTY. and windows saying my USB DEVICE "TILT" isn't recognizable. I think i'm in deep SH!T.
The phone itself will boot all the way everynow and then, like letting it sit for a few hours, but even when it's fully booted, the same thing happen with the USB port thing. This sucks... Thanks for helping. What should I do next?
**UPDATE** Luckily the phone started up, i did a CLEAR STORAGE, went back to the tri-color screen, switch USB cable, ran MTTY with cmd/info 8 this is the result.
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 434 (0x1B2) is bad block
BLOCK 1120 (0x460) is bad block
BLOCK 1394 (0x572) is bad block
BLOCK 1395 (0x573) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x9E40
Partition[3], type=0x4, start=0xAB80, total=0x10740
CE Total Length(with sector info) = 0x5615C00
CE CheckSum Length(without sector info) = 0x55C0000
Bacuy try the commands i used, worked perfectly.
cweems said:
Bacuy try the commands i used, worked perfectly.
Click to expand...
Click to collapse
What worked for you might not work for him. You had only one bad black while he has 4. Please don't encourage mtty commands unless you know what you are doing. His SPL 1.93 might not be compatible as well. It's best to just wait for GSLEON3 to inform him/her on the next step.
I've been using WM 6.1 with Dutty's dual touch rom for over a month now, turned my phone off about 30 min ago, and when i turned it back on, it shows SPL screen (red,green,blue,white), and white bar says "Serial"
top right says
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
Also when i soft reset, for a split second i get white screen that says "warning no image file!", right before it goes back to spl screen
Has anyone encountered this before? I tried soft reset, but it doesnt do anything, it just goes back to this screen. I havent installed anything besides that HTC rom
(i'm using ATT Tilt, and i did install the correct radio as well)
disable usb connections in activesync, use mtty to connect to usb and then type command "info 8" without the "" and paste the output here, and wait for gsleon3 to get to you
XtreMe_G said:
disable usb connections in activesync, use mtty to connect to usb and then type command "info 8" without the "" and paste the output here, and wait for gsleon3 to get to you
Click to expand...
Click to collapse
do what xtreme_g says but at same time a suggestion: have u done a hard reset?? if not giv it a shot maybe that might help ...
i did a hard reset, it went back to normal, actually, OS loaded again (dutty's), this morning i turned off the phone, and when i turned it back on, its on that SPL screen again
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 193 (0xC1) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0x7640
Partition[3], type=0x4, start=0x83C0, total=0x12F00
CE Total Length(with sector info) = 0x4221E00
CE CheckSum Length(without sector info) = 0x41E0000
t3nn15dud5 said:
i did a hard reset, it went back to normal, actually, OS loaded again (dutty's), this morning i turned off the phone, and when i turned it back on, its on that SPL screen again
Click to expand...
Click to collapse
Try to do a boot command (type "boot" without quotes) from mtty and I think it'll boot. Everytime you power off it though, you would go back to the bootloader screen I had the same problem but was solved when I flashed another ROM.
Can i somehow just wipe out everything and reinstall a fresh ROM?
which ROM did u use ?
pfcsabre said:
Try to do a boot command (type "boot" without quotes) from mtty and I think it'll boot. Everytime you power off it though, you would go back to the bootloader screen I had the same problem but was solved when I flashed another ROM.
Click to expand...
Click to collapse
Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700 is the one i just flashed a day ago, and its stil giving me spl screen when i power off
before that i had Dutty's WM6.1 5.2.19209 Release
t3nn15dud5 said:
I've been using WM 6.1 with Dutty's dual touch rom for over a month now, turned my phone off about 30 min ago, and when i turned it back on, it shows SPL screen (red,green,blue,white), and white bar says "Serial"
top right says
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
Also when i soft reset, for a split second i get white screen that says "warning no image file!", right before it goes back to spl screen[...]
(i'm using ATT Tilt, and i did install the correct radio as well)
Click to expand...
Click to collapse
Don't worry about that, I believe you have a SD card. Its not finding a Image File on the SD card. Thats how you flash via an SD card.
The reason it goes to SPL i think there is a Flash Flag that didn't get clear or something. I'm not that smart about this. Thought I am trying to learn mtty.
I accidently ran the rom before the hard spl, Doh!
Alright everyone im sorry in advance for this, but dont worry, I have my fire extinguisher out and any help will be worth any and all flaming. I was changing my rom on my tilt from the original 6.0 to the Apr 29 dutty rom. I got side tracked in the middle of it and accidently ran the rom instead of the hard spl. As soon as i hit next I realized it. I know I feel like and idiot. Well the screen started to load and is now holding firm at the 17% download mark and isnt moving anywhere. My plea for help is to ask if there is any steps I can take to recover the phone at this stage or am i pretty much screwed. I have been searching the forums on any steps to go through but since my phone is still in load mode I thought my situation may be original enough to post. As of now at 12:34am on Sep 1st my phone is still connected to the computer and showing the white loading screen. I will plan to leave this going until it shows me an error or I see the expected reply that im doomed. If you guys can pull me out of this one I promise that paypal will be your pal. Thanks to all that reply.
Text at the bootloader screen:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
Serial
-------------------
When this first happened I was able to use mtty to boot to the OS. Now when I plug it up to my PC it changes from "Serial" to "USB" however I get the warning that Windows does not recognize the USB device.
Occasionally the device will boot to the OS but when I attempt to insert my SIM card (I've removed it so I can continue to use my service) the device reboots and goes straight to the bootloader screen. When it boots to the OS and I don't insert my SIM card ActiveSync doesn't recognize it.
I had been using Dutty's Duttys_Diamond_Rom_Ruu_Signed_5.2.1588_1.65.16.25_V1 ROM at this point. I then tried to flash the Official AT&T ROM found in this thread. Didn't help. I've tried flashing HardSPL 3.56. Didn't help.
Can I still save this thing? What else can I do? Am I missing something obvious here?
My phone ran into the same issue in the last 24hrs. Leaving the battery out for an hour "fixed" it, only to have it reoccur overnight.
Bump. I could really use some help on this issue.
Have you tried reflashing the rom using a microsd card? What spl version are you running?
Alibaba0101 said:
Have you tried reflashing the rom using a microsd card? What spl version are you running?
Click to expand...
Click to collapse
Multiple times. I've tried reflashing the Duttys ROM I was using (see original post) and the official AT&T ROM, which is what is now installed on the device. I am/was running HardSPL 1.0 and I tried flashing HardSPL 3.56 from my micro SD card but the text at the bootloader screen is still:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
Which leads me to believe that I am still running HardSPL 1.0
Just now the device attempted to boot to the OS but froze at the green WM6.1 screen. I then tried a soft reset and it went back to the bootloader screen. It seems that leaving the battery out for some time will allow the device to boot to the OS. Next time I attempt to boot it up I'll insert my SIM card and see if I get anywhere with that.
Here's a thought. When I bought my Tilt AT&T sent me a new SIM card but I never bothered to have my old SIM card transferred to the new one. I've been using my old Cingular SIM card. Could this an issue? I had read that some older versions of HardSPL may have trouble with older SIM cards...
So I took out the battery and let it sit for a while, put my SIM card and the battery back in and it booted to the OS. Sweet. However, the screen is unresponsive to touch and does not shift from portrait to landscape when I slide the screen. Also, Activesync did not recognize the device.
I removed my SIM card and it booted to the bootloader but Windows did not give me the error that it didn't recognize the USB device so I opened MTTY and was able to connect.
Here's the info 8 message:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 262 (0x106) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0xB540
Partition[3], type=0x4, start=0xC2C0, total=0xF000
CE Total Length(with sector info) = 0x61C1600
CE CheckSum Length(without sector info) = 0x6160000
Cmd>
I'm going to toss in my unregistered SIM and force boot to the OS... at least I can charge the damn battery now.
EDIT: I inserted my unregistered SIM and tried to force boot to the OS using MTTY but the screen went black and I've got a red light. Removed the battery and rebooted to the bootloader. Now Windows no longer recognizes the device. But I'm confident I'll be able to boot to the OS later. But I've gotta get ready for work now. Frustration!
Did you try this?
http://forum.xda-developers.com/showthread.php?t=420683
Alibaba0101 said:
Did you try this?
http://forum.xda-developers.com/showthread.php?t=420683
Click to expand...
Click to collapse
This looks promising. I had seen this but forgot about it because I hadn't had any luck booting to the OS. I'll definitely try this when I get home.
tri-color phone screen
hey, i had the same problem and i fixed it. i took the battery out and saw the 4 golden tabs behind the battery. there was two tabs that u could pull out. i lightly pulled them out a little bit. the problem was that the tabs wouldnt hit the battery to charge it. thats why it put the tri colored screen on the front. also my charger fit into the charging hole in the phone, but it had to be moved around to much that it did not fit exactly. I have been rough with the charger so it moved the inside of my phone around. i put the charger in the phone and moved it around gently around untill the light lit up on the front at the top by the word at&t. after it was completly charged, i turned it on and it worked perfectly. i hope this helps in whoever may have this problem because i know it sucks!
Thanks
One of my superiors wanted me to dispose of his old v1615/Kaiser, saying "...this isn't working. Dispose of it properly." Ever the fiddler, I wanted to know if it could be used again, and in so doing I found xda-dev!
I've been searching around, and reading up - Wikis and forum posts - but I've yet to find a solution to my problem: the Kaiser hangs at the Vodafone logo. I found the MTTY instructions threads etc., so to clarify the situation here is a MTTY dump (first two carriage returns and commands included...):
Cmd>
Cmd>set 16 0
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
Storage start sector=0x9040, total sector=0x12280
Storage start block=598, total block=1162
Total Bad Block in CE: 0
Erase physical block from 886 to 2032
formatstorage Bad block found: 1201
formatstorage Bad block found: 1795
si backup: Erase physical block from 2032 to 2048
No card inserted
OSSIPreLoad ++
At this point it hangs, and drops the USB connection - presumably while the device is reseting the device tree - rendering MTTY useless.
Has anyone come across this issue?
I've not experienced that but I do recall reading similar posts. What happens when you attempt to hard reset using the soft keys and stylus method (as described in the users manual and wiki)? You need to walk before running and this should be the first step before going anywhere near the device with mtty or similar tools. Make sure it's been charging for a few hours so the battery is full or nearly so and ensure you know which buttons to press and are careful just to press the soft keys only. This operation can be fiddly and a few times my attempts at a soft key induced hard reset have failed because my big fat fingers have also ended up pressing other buttons at the same time.
Before finding xda-developers.com I tried a soft reset, which didn't have any effect whatsoever. I've tried soft resetting four times - probably out of frustration.
After those failed, I did a hard reset, which also had no effect. In fact, the MTTY dump on the original post is what happened directly after the first hard reset.
The device is still functional, but it seems unusable for now.
could be a corrupt rom, try flashing another rom
just remembered it isn't hardspl'
phuedx said:
I did a hard reset, which also had no effect.
Click to expand...
Click to collapse
Precisely what does that mean - what happened? If absolutely nothing happened and it didn't start the hard reset procedure (with a little progress bar displayed on the screen), then try hard resetting again (making sure you're only pressing the correct buttons at the same time as when you poke the stylus in) because it may have been finger trouble (it's easy to get this wrong).
Hy,
I have a Kaiser that when I power it on it does the following:
1 - black screen with "Smart Mobility" in the middle
2 - some red numbers shown on the bottom right corner
3 - Windows Mobile 6.1 green logo
4 - Windows Mobile 6.1 green logo and "cleaning device memory, please wait" message
It stays this way for about 5 minutes and next it turns itself off.
Can anyone help?
BR
Did u try a hard reset.
If not do it and check it again.
Pls try to take the backup.
Yes I already tried Hard-Reset but it does the same thing.
As for backup... it doesn't matter anymore, I just want to get the phone working!
And I got the phone in Bootmode tried to flash it, the flash bar shows up, but it always stays at 0% and gives "comunication error".
BR
Futuro said:
Yes I already tried Hard-Reset but it does the same thing.
As for backup... it doesn't matter anymore, I just want to get the phone working!
And I got the phone in Bootmode tried to flash it, the flash bar shows up, but it always stays at 0% and gives "comunication error".
BR
Click to expand...
Click to collapse
I had the exact same issue with my Tilt a couple of months ago. I bought a new battery, the issue was gone and hasn't happened since.
denco7 said:
I had the exact same issue with my Tilt a couple of months ago. I bought a new battery, the issue was gone and hasn't happened since.
Click to expand...
Click to collapse
HUH????.... really?... ok it's worth a try!
I'll get back with results!
I had a friend of a friend who had a Kaiser... changed the battery but... nothing, still the same "clearing memory... turn off" problem!...
I ran this command on MTTY... does this help identify the problem:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 307 (0x133) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0xA6C0
Partition[3], type=0x4, start=0xB440, total=0xFE80
CE Total Length(with sector info) = 0x5A7A200
CE CheckSum Length(without sector info) = 0x5A20000
Click to expand...
Click to collapse
Futuro said:
I had a friend of a friend who had a Kaiser... changed the battery but... nothing, still the same "clearing memory... turn off" problem!...
Click to expand...
Click to collapse
Have you try to flash another rom or reflash your stock...I noticed hardreset is not working..