Related
Alrighty so here is the issue.
I got a new AT&T Fuze and tried to load "RaphaelHardSPL-Unsigned_190_1_3".
1) I load Windows Mobile Device Center
2) Run the aphaelHardSPL-Unsigned_190_1_3 exe
3)THe load bar comes up, HTC screen goes black and then the loader fails at %0.
4) It gives the 262 error
5) I take the battery out, turn on and phone is fine
What is the problem?
Ps...
This on on my Visa 64 sp2
ROM Development Thread
UndertoW said:
Alrighty so here is the issue.
I got a new AT&T Fuze and tried to load "RaphaelHardSPL-Unsigned_190_1_3".
1) I load Windows Mobile Device Center
2) Run the aphaelHardSPL-Unsigned_190_1_3 exe
3)THe load bar comes up, HTC screen goes black and then the loader fails at %0.
4) It gives the 262 error
5) I take the battery out, turn on and phone is fine
What is the problem?
Ps...
This on on my Visa 64 sp2
Click to expand...
Click to collapse
Have you searched in the Raphael ROM Development thread. I believe this is covered in that thread.
I did check the forum and an extensive google search with no useful information found......not that it's not there.....just that i could not locate it.
Any specifics or a link would be much appreciated.
thanks in advance
Rinse and repeat.
I occasionally get a an error when flashing a new ROM, Radio etc. just try again if that fails seek advice from the wiki/appropriate thread.
mcspikesky said:
I occasionally get a an error when flashing a new ROM, Radio etc. just try again if that fails seek advice from the wiki/appropriate thread.
Click to expand...
Click to collapse
I tired it about 4 or five times...all with the same error code.
do you know where i can find these appropriate threads?
thanks in advance
Still looking for some advice help bump
I am having the same problem with the same Vista set-up. I've even tried running the RUU and Windows Mobile Device Center in compatability mode, with no success.
Ok, I just figured it out. do not start the Mobile device center in Vista. Just make sure that the phone shows up as a device under my computer. took about 10 seconds to flash after that. (and I had the sim and sd card removed for good measure).
Thank you very much...i'm now up and running 4.5 and love it.
Thank you dkevinscott very much for you time and help!
how to flash my htf fuze.
hi, is anyone can get me a hand to flash my htc fuze, thankyou very much.
I'm still getting this error.... anyone have a work around? I have XP
i had same problem it came down to qualcomm drivers .no workaround for me just used vista
ITT: People who refuse to spend 10 minutes reading for themselves
Same problems
Hi there,
I have a Xperia X1 and i'm trying to upgrade to 6.5 aswell.
Everytime i launch the exe file (Kovsky customRUU) it'll give me a 262 error.
I'm running vista and didn't run mobile center.
The X1 appears in my explorer though.
But still. It's a nogo.
Pls help
HTC Touch Pro, Fuze HardSPL Error 262 FIX
Alright, this is how i fixed my 262 error after ripping out all my hair for a week.
- Plug your phone into any working usb port (make sure Active sync is up and running)
- Run RaphaelHardSPL-Unsigned_190_1_3.exe and on the first screen pop up, 9 files will be created in the directory you run the .exe from.
- Copy these 9 files to another folder because you will be clicking cancel on the pop up which will in turn erase the 9 files it created.
- Click cancel on the pop up.
- Go to the folder in which you copied these 9 files to.
- Run ROMUpdateUtility.exe and the same screen pop will appear as before.
- Follow the prompts and it should work.
i had this exact same error. this worked flawlessly. thanks!
xidesu said:
Alright, this is how i fixed my 262 error after ripping out all my hair for a week.
- Plug your phone into any working usb port (make sure Active sync is up and running)
- Run RaphaelHardSPL-Unsigned_190_1_3.exe and on the first screen pop up, 9 files will be created in the directory you run the .exe from.
- Copy these 9 files to another folder because you will be clicking cancel on the pop up which will in turn erase the 9 files it created.
- Click cancel on the pop up.
- Go to the folder in which you copied these 9 files to.
- Run ROMUpdateUtility.exe and the same screen pop will appear as before.
- Follow the prompts and it should work.
Click to expand...
Click to collapse
work!!
man i spend two days without sucess.this working .thnx
my friend wants to update to OS 6.5.
he changes the file name to "Kovsimg.nbh" and put it in Memory card.
he tries to update by following instructions.
after he sees 4 Color on screen, the screen shows "loading". but that Loading takes long time and nothing happen after that.
keep on showing "loading".
what should he do?
Have you done HARD Spl first?
0. Make sure phone is hard-spl first
1. Make sure SD card is formatted with fat-32
2. rename the image file (ruu_signed.nbh) to rhodimg.nbh, then copy that to the ROOT OF THE MICRO SD CARD, Insert card into phone
3. Set your phone in bootloader (Hold the "volume down" and hold the power on button until you see the tri-color screen.
4. Then follow the on-screen instruction
5. (OPTIONAL) -after flash, make sure to hardreset (pull battery, insert battery then hold green and red PHONE buttons (send/end) and hold powerbutton) follow onscreen instruction.
thanks for the info
I've tried the above and somehow it won't work on my TP2, it stays at "Serial" text in the white box, I'm assuming it already went past the SD slot then? Checking for the image.
I have the Energy rom loaded on the SD card, named as explained in the first post in this topic, it is placed in the root of the SD card, no folders or other files exist on that card. I removed the SIM card from the phone just to be sure. Is there anything I am missing, or is there anyone else who actually used this method to flash his or her device?
Info:
SPL: OliNex 0.85
ROM: |RHOD|6.5|ROM|WWE| ★ EnergyROM "Warhawk" (23016) ★ | Built Aug 21 |Manila 2.5 / 2.1|
SD Card: 4GB MicroSDHC (No brand on card, supplied with the branded T-Mo TP2 (Vario V)
Formatted: fat-32
Thanks
The nbh file needs to be in capital letters! RHODIMG.nbh
And step 5 isnt to be done until the "Tap screen to set up device" screen!
Just reset when your phone says Update successful!
And done, name changed to the correct format. No luck. Reformatting the card now to see if that changes anything. Update in a few.
And that too didn't work sadly. Either someone here notices I'm doing something wrong, or I'll just wait till I get near a machine natively running Windows Running Mac OS here so can't run the executable, and read that it's not quite a good idea to flash it from a virtual OS.
PositiveCreep said:
And done, name changed to the correct format. No luck. Reformatting the card now to see if that changes anything. Update in a few.
And that too didn't work sadly. Either someone here notices I'm doing something wrong, or I'll just wait till I get near a machine natively running Windows Running Mac OS here so can't run the executable, and read that it's not quite a good idea to flash it from a virtual OS.
Click to expand...
Click to collapse
You will want to partition your card so the nbh image is in a partion of at the largest 1G, anything larger makes it hard for the phone to find and read the nbh file! I have a 1G card just for flashing and it works perfect! And it also may be the mac, they never play nice with windows!
It's not the mac screwing it up in this case as I am using a virtual Windows OS to work on the card. (MacOS leaves some folders on the card that I don't want on it)
Will try partitioning the card, cheers. I'll update when I know more. ANd thanks for the help ^_^
Update:
Partioned the MicroSD card to 0.5GB, no change sadly.
thanks for information
Ok, SD update worked now, however, step 5 won't go (Oh crap...) Have the grey screen with "Update Complete" and "UPDATE SUCCESS" However, it won't do anything if I hold down Send/End/Power at the same time for over 10 seconds. How long should that take normally? What's my best option right now? Can't see any other than to unplug the phone and take out the battary, however, will this brick it?
PositiveCreep said:
Ok, SD update worked now, however, step 5 won't go (Oh crap...) Have the grey screen with "Update Complete" and "UPDATE SUCCESS" However, it won't do anything if I hold down Send/End/Power at the same time for over 10 seconds. How long should that take normally? What's my best option right now? Can't see any other than to unplug the phone and take out the battary, however, will this brick it?
Click to expand...
Click to collapse
When is says "UPDATE SUCCESS", just rest with the stylus.
Dave
Thanks for the swift reply! Done it, it's booting up as I am typing this. Didn't quite have the guts to just do that without having read I could when flashing from SD. (Was unsure how the device would react to soft reset then a first booth with the SD present etc)
Anyways, rambling. Thanks!
these post are telling me how to flash while the rom is already on the phone, but i'm missing the step on how to get the rom file on the phone in order to move it to the sd card.......... how do i get the file to the phone? do i put it onto the phone from the computer or do i go to my browser on my phone and download it from there to the phone
htctpII said:
these post are telling me how to flash while the rom is already on the phone, but i'm missing the step on how to get the rom file on the phone in order to move it to the sd card.......... how do i get the file to the phone? do i put it onto the phone from the computer or do i go to my browser on my phone and download it from there to the phone
Click to expand...
Click to collapse
Everything you need to know is HERE. I really suggest you fully read the instructions so you avoid bricking your phone by mistake.
In re: making sure you're hardspl'd first, does that still apply if you're flashing an official ROM? Or just for user cooked ROMs?
I'm about to update my Verizon TP2 with the newly released official 6.5 from verizon. I'm not hard spl'd, and honestly, know very little about that particular modification.
not for official
I dont think you have to be hard SPL'd for an official ROM. I think everything is included in the ROM package. (at least for T-Mobile it is)
btw the .nbh does not have to be named in all capitals. I have personally done it both ways with no problems at all. RHODIMG.nbh works just as well as rhodimg.nbh
kwambewright said:
I dont think you have to be hard SPL'd for an official ROM. I think everything is included in the ROM package. (at least for T-Mobile it is)
Click to expand...
Click to collapse
Thanks for the quick response!
Sadly, the way the install file is set up to work, I can't get to the nbh file. It insists on installing that via an active sync connection. I was hoping it would extract from the exe and schedule it for active sync installation, then I could hunt down the ROM, copy it to my SD card, and run it from there.
fortunz said:
Thanks for the quick response!
Sadly, the way the install file is set up to work, I can't get to the nbh file. It insists on installing that via an active sync connection. I was hoping it would extract from the exe and schedule it for active sync installation, then I could hunt down the ROM, copy it to my SD card, and run it from there.
Click to expand...
Click to collapse
hmm.. sorry for kicking this post, but you can unpack the exe-file with winrar. just grab the biggest file you can find (RUU_signed.nbh, and rename it to rhodimg.nbh), copy it to your root-folder (fast way for accessing bootloader is to also copy the "EnterBootLoader.exe" -file to your SD-card, and to start that file after copying both the files). Now just enter the bootloader, and it works! (don't be scared when the screen goes black for a moment, and the bootloader has reloaded. It's meant to do that )
I still have a little question by the way: is it possible to flash the hardSPL this way? or should i rename it to something else?
No, Hard SPL needs to be done from the PC as it checks IMEI online and IP address. You only get 1 licence, can ask for more or purchase more licences, but it can't be done any other way...
ultramag69 said:
No, Hard SPL needs to be done from the PC as it checks IMEI online and IP address. You only get 1 licence, can ask for more or purchase more licences, but it can't be done any other way...
Click to expand...
Click to collapse
Yeah, it's a pity this has been done (though I understand why...)
My device cannot connect to PC anymore, so cannot use HSPL anymore!
InjecTioN said:
hmm.. sorry for kicking this post, but you can unpack the exe-file with winrar. just grab the biggest file you can find (RUU_signed.nbh, and rename it to rhodimg.nbh), copy it to your root-folder (fast way for accessing bootloader is to also copy the "EnterBootLoader.exe" -file to your SD-card, and to start that file after copying both the files). Now just enter the bootloader, and it works! (don't be scared when the screen goes black for a moment, and the bootloader has reloaded. It's meant to do that )
Click to expand...
Click to collapse
Much obliged. I've actually been scared off the official vzw 6.5 because of issues upgraders have reported, but someday I'll put that to use.
I have created this post because I was honestly baffled by the NAND install threads for the Vogue that I found, that claimed to be "straightforward" and simple, but the people who wrote them leave a lot of gaps that you have to figure out. Perhaps they have been doing it for so long now, that they just 'assume' you will know stuff, so here are step-by-step instructions for someone who has zero experience with Android, and all they know is that they have a Window mobile phone.
So, Here is the NAND install process (will install Android to your internal memory, which is much better than running from the SD card) for the HTC Vogue (240x320), CDMA or GSM. I believe this is the most straightforward tutorial on this entire site, and all files you need are provided in this post; no file-hunting necessary like with other tutorials. Keep in mind, this process will wipe your internal memory and replace it with Android, so you should backup any personal files you have stored on the phone. If you have a CDMA phone (Verizon, Sprint, etc.) then you should make sure to backup your Contacts using a 3rd party program. GSM phones however (ATT, T-Mobile, etc.), typically store their contacts to a SIM card, which is not altered by this process. You do not need to backup your SD card, since it is also not altered when installing Android.
Dependencies: This process works for any ROM release that provides an "androidinstall.tar" file in their download package.
First and foremost, make sure you have unlocked your phone ("2.31 CoKe" HardSPL for CDMA Vogues). If you have ever flashed a custom Windows ROM from this site or ppcgeeks.com, to your device, then you most likely already have an unlocked phone. If not, perform the steps HERE first, before continuing AND flash to a custom Windows Mobile ROM (non-stock) and make sure your phone is provisioned (you can get and receive calls), and that you can use data (if you have a data plan).
1. Wipe your SD card, and make sure it is formatted FAT32
2. Create a new folder in the root of the SD card called "andboot"
3. Download the ROM release package of your choice (for example, you can download the 240x320 version of Myn’s Warm Donut - [RLS 5 - 04/24/2010] HERE)
4. Extract files from STEP 3 and put ONLY the "androidinstall.tar" file in the andboot folder on the SD card, by itself (no other files are needed)
5. You are DONE putting files on your SD card. At this point, put the SD card into your phone.
6. Download the latest NBH file that begins with "voguimg-240x320-..." (needed for all Vogue Android ROMs): HERE
7. Download the RUU Update Utility (needed for all Vogue Android ROMs): HERE
8. Rename the NBH file to from STEP 6 to "RUU_signed.nbh" and place it inside the folder with all the other files from STEP 7
9. Now, put your Vogue in bootloader mode: Hold down power, camera, and the small reset hole (with your stylus), until you see the tri-color screen, and it says "Serial" at the bottom
10. Plug your phone into your computer, and the "Serial" text should change the "USB"
11. Now, run the "ROMUpdateUtility.exe" from STEP 7, and click the "Next" or "OK" buttons to go through the flash/ROM update process, until your phone shows a progress bar on its screen and is updating.
12. As soon as that progress bar finishes the phone will automatically reboot; at this point unplug the phone from the computer
13. Now, watch carefully during the Linux boot process...there will be a quick message that says "Hold down Volume Up or D Pad". Just press and hold the center D-Pad button until you see the screen change to the installer menu. If you happen to miss it, and it continues loading, then just use your stylus to press the reset button (it will not hurt the phone or any files to try again as many times as you need to.)
14. You will now see a black and white menu. Select option 1, to "Install..."
15. Select "Yes" on the recommended prompt that follows
16. Once it says the Install process is complete and it returns you to the menu, just reboot your phone with the reset button
17. At this point just WAIT. Do NOT press the volume up button again, and do not do anything until you see the Android desktop. You may get an error saying that it could not find a file or something like that, but just ignore it...do not get impatient! Pretty soon the Android progress bar will show on the screen (might take up to 5 minutes), then the Android desktop will load.
DONE. Enjoy Android on your Vogue! You can now delete all the files on the SD card if you wish...Android will recreate anything it needs on boot-up each time.
MASS STORAGE FIX (USB to PC): You can get the Mass Storage fix HERE so that your storage card will show up as a drive on your computer. This is a widget, and not ROM specific, so should work for any Android ROM.
KAISER WI-FI FIX (for the Kaiser phone ONLY!): Download the Wi-Fi fix HERE (intended for use with 'myn's Warm Eclair RLS1', linked in STEP 3)
I do not ask for donations, just say 'Thanks' if this helped you.
***
UPDATE: This Thread is now featured on Wired.com's News Site!! Link: http://www.wired.com/gadgetlab/2010/04/windows-mobile-android/
***
please elaborate on step 8. what are we extracting here
Great post. Just some clarifications I thought would be helpful.
1. reminder to all - you can use SDHC cards for this, those being greater than 2gb, but make sure you format them to FAT32.
5. in some instances there are androidupdate.tar files that go with the build too, in which case that too needs to be placed in the same andboot folder
8. clarification, you'll be replacing the RUU_signed.nbh file with the 320 nbh file you download. So, you'll have to delete the ruu_signed.nbh that came with the update utility, and rename your downloaded 320 nbh to ruu_signed.nbh and place it in the update utility folder so it uses that file instead.
9. to enter bootloader mode you have to press those 3 buttons down for about 2 seconds, not just a quick tap. This bootloader is your failsafe fallback to reinstall if your operating system goes funky.
13. If volume up isn't working for you, try holding down the button in the middle of the directional pad. The last nbh file I used required this instead of the awkward volume-up. Regardless, be sure to do this quickly as soon as the phone reboots itself.
16. After the install process is complete you'll be brought back to the same menu you arrived at by holding down the button on startup, you may then select "update" or "upgrade" from that same menu to activate the androidupdate.tar file you may have copied to your andboot folder. Once done, just select "exit" or reset.
17. He's not kidding, first boot can take a very long time.
If you run into problems and just need a functional phone for a bit, download the nfsfan rom (or any other custom roms), put phone into bootloader and run the nfsfan rom utility from your windows desktop. Don't reinstall a locked carrier-specific rom that you might have used to update your radios otherwise I understand your Coke bootloader gets wiped out and you'll have to do that again. Alternatively, there is an older, dummy-proof Android ION build that will install the entire ION build through the rom update utility to your nand at http://sourceforge.net/projects/androidhtc/files/2009-12-17/androidinstall.zip/download
I'm no super-expert so if I have any misinformation in my post, or there are other shortcuts, please feel free to edit it or let me know and i'll modify it.
MikeMurphy said:
Great post. Just some clarifications.
8. clarification, you'll be replacing the RUU_signed.nbh file with the 320 nbh file you download. So, you'll have to delete the ruu_signed.nbh that came with the update utility, and rename your downloaded 320 nbh to ruu_signed.nbh and place it in the update utility folder so it uses that file instead.
Click to expand...
Click to collapse
where is this file?
CasopoliS said:
where is this file?
Click to expand...
Click to collapse
You're looking for the vogue 320 files, not the vogue eclair 320 files unless you're installing an eclair (2.x) build.
The .nbh files are usually referenced on the build thread in the forums, but if they are not head over to http://sourceforge.net/projects/androidhtc/files/ and download the latest.
(NOTE: I suggest you run at least the Feb 23 build at http://it029000.massey.ac.nz/vogue/files/?C=M;O=D as it enables the openGL support)
MikeMurphy said:
You're looking for the vogue 320 files, not the vogue eclair 320 files unless you're installing an eclair (2.x) build.
The .nbh files are usually referenced on the build thread in the forums, but if they are not head over to http://sourceforge.net/projects/androidhtc/files/ and download the latest.
Click to expand...
Click to collapse
the latest isnt there its here
http://it029000.massey.ac.nz/vogue/files/?C=M;O=D
now now, gents, you're both right - dzo's latest are in one spot, vilord's latest are in the other, and they don't always contain everything the other does. vilord mentioned trying to get them in one spot but I don't know if there's been any progress on that.
it keeps hanging up at the progress bar and both stay at 0% it looks like the active sync is gone once in bootloader it goes gray and then its gone from tray in bottom right corner. it seems like once in bootloader mode i have no active sync connection it just hangs Then the updater goes into its recovery any help please
razorr69 said:
it keeps hanging up at the progress bar and both stay at 0% it looks like the active sync is gone once in bootloader it goes gray and then its gone from tray in bottom right corner. it seems like once in bootloader mode i have no active sync connection it just hangs Then the updater goes into its recovery any help please
Click to expand...
Click to collapse
go into bootloader before plugging your phone in by pressing and holding power button, camera button, and then use stylus to hit reset button.
once you get into bootloader, plug your phone in and then run the rom update
incubus26jc said:
go into bootloader before plugging your phone in by pressing and holding power button, camera button, and then use stylus to hit reset button.
once you get into bootloader, plug your phone in and then run the rom update
Click to expand...
Click to collapse
that is the way that i have been doing it as per the instructions, Any other suggestions? I just did a hard reset and restored the phone to out of the box if that helps out any.
thanks
razorr69 said:
that is the way that i have been doing it as per the instructions, Any other suggestions?
thanks
Click to expand...
Click to collapse
the only reason i said that is because active sync should have nothing to do with it. i dont think active sync should come up or shut down during this process. Do you have the RUU_signed.nbh named properly?
razorr69 said:
that is the way that i have been doing it as per the instructions, Any other suggestions?
thanks
Click to expand...
Click to collapse
Activesync has nothing to do with updates via the rainbow screen bootloader and will not sync.
You have already install the Coke bootloader? What OS are you running?
Thank you so much. Been needing something like this since the other NAND tutorials for Android didn't tell you what files to use or had outdated/non-working links.
MikeMurphy said:
Activesync has nothing to do with updates via the rainbow screen bootloader and will not sync.
You have already install the Coke bootloader? What OS are you running?
Click to expand...
Click to collapse
6.1. I followed the inst.
put the tar in andboot folder on sd
renamed the voug img file put it in the androidinstall folder on my desktop
put the rest of the files from myns donut into the androidinstall folder
then bootloader plug in usb then rom updater
everything goes fine intil it hangs on the progress bar at 0%
razorr69 said:
6.1. I followed the inst.
put the tar in andboot folder on sd
renamed the voug img file put it in the androidinstall folder on my desktop
put the rest of the files from myns donut into the androidinstall folder
then bootloader plug in usb then rom updater
everything goes fine intil it hangs on the progress bar at 0%
Click to expand...
Click to collapse
What OS are you running on your computer?
The ROM update utility really just installs the .nbh file which is somewhat of a front-end loader mechanism. Once that file is installed, then the phone resets, you hold down a button and you enter into the menu that lets you actually install android from the androidinstall.tar file in your andboot folder.
Here is a fail-proof method that I think will resolve your goofy androidinstall folder.
Download this
http://74.53.45.2/~evadmin/nfsfan/Public Releases/Vogue 6.5/ROMS/NFSFAN's WM6.5 1.00 FINAL ROM.rar
Then replace the .nbh file with the vogue 320 nbh. Then, run it when your phone is already in the bootloader screen.
Excellent post
I'm linking this from Warm Donut on the first post.
MikeMurphy said:
What OS are you running on your computer?
The ROM update utility really just installs the .nbh file which is somewhat of a front-end loader mechanism. Once that file is installed, then the phone resets, you hold down a button and you enter into the menu that lets you actually install android from the androidinstall.tar file in your andboot folder.
Here is a fail-proof method that I think will resolve your goofy androidinstall folder.
Download this
http://74.53.45.2/~evadmin/nfsfan/Public Releases/Vogue 6.5/ROMS/NFSFAN's WM6.5 1.00 FINAL ROM.rar
Then replace the .nbh file with the vogue 320 nbh. Then, run it when your phone is already in the bootloader screen.
Click to expand...
Click to collapse
Thank you will try it now. Running xp pro on my desktop
razorr69 said:
Thank you will try it now. Running xp pro on my desktop
Click to expand...
Click to collapse
XP Pro always worked well for me. I'm running Win7 x64 ultimate and recently my phone was recognized as a USB Sync Device in the bootloader mode which doesn't work for the rom update utility. This was occurring both with and without the installation of the MS Mobile Device Center app. To solve this I installed XP Mode and attached the usb device to the XP Mode and it recognized correctly as the Qualcomm MSM thing.
Just an FYI.
MikeMurphy said:
XP Pro always worked well for me. I'm running Win7 x64 ultimate and recently my phone was recognized as a USB Sync Device in the bootloader mode which doesn't work for the rom update utility. This was occurring both with and without the installation of the MS Mobile Device Center app. To solve this I installed XP Mode and attached the usb device to the XP Mode and it recognized correctly as the Qualcomm MSM thing.
Just an FYI.
Click to expand...
Click to collapse
when i go into my computer it just says mobile device
razorr69 said:
when i go into my computer it just says mobile device
Click to expand...
Click to collapse
same result error 262 update error. i dont get it this is so simple. 1 of the 4 steps is establish a connection with active sync dont know how to do that once im in bootloader mode it's like there is no connection but the phone shows the progress bar
I've rooted so much and learned so much in the past month that I'd like to take that extra step. Opinions?
I'd like to try Cyanogenmod, but I've been failing miserably trying to put it on my device.
I've tried flashing it through this way: http://wiki.cyanogenmod.com/wiki/Samsung_Galaxy_S:_Full_Update_Guide but I couldn't get ClockworkMod to reboot. Once I did get it to reboot I had a hard time loading or flashing Cyanogenmod because it kept saying that it failed to load and installation was aborted. What am I doing wrong guys? I'm following those instructions in the link to a T. I put the gapps file and the update cm 7.0.1 in the folder called the external_sd even though I do not have an external SD card, but I was guessing that's where the root of the internal memory is. Am I missing something? Is it really this hard? And is Cyanogenmod really worth it?
put the update/zip file in internal SD,not inside any folder.remove external SD card.now try flashing.
senotrius said:
put the update/zip file in internal SD,not inside any folder.remove external SD card.now try flashing.
Click to expand...
Click to collapse
Couple things. When I connect my phone to the computer there is no folder that says internal SD unless the stuff that shows up with all the folders is the internal SD. I do not have a removable SD card.
Do I have to flash or wipe anything before I put the update/zip file on my phone?
Ok, successfully did it! I installed the cyanogenmod so I'll take it for a spin. However, there is one thing that I can't figure out. I'm trying to download all the Google apps from the market, but anything that I try downloading from the market it just stays in the downloading progress bar and nothing happens.
I installed the separate apk file gapps-gb-20110828-signed the same way I installed Cyanogenmod, but nothing. Can anyone help please? Also, I used the Navigation app a lot, but I can't even seem to find that one on the market...
Now it's working. Ok. Few questions for you guys. Any way to turn off an "LED notification" whenever I get a text message the bottom soft keys light up and stay lit up until I check the message.
Still don't know how to get the turn by turn Navigation application.
EDIT: How do you get Swype as well on Cyanogenmod?
pk1025 said:
Now it's working. Ok. Few questions for you guys. Any way to turn off an "LED notification" whenever I get a text message the bottom soft keys light up and stay lit up until I check the message.
Still don't know how to get the turn by turn Navigation application.
EDIT: How do you get Swype as well on Cyanogenmod?
Click to expand...
Click to collapse
turn off pulse notification in settings,think its under display.
turn by turn-there's a modded google maps app in the forum.under apps section.
I don't use swype but same ques was asked before and I read u hv to download the latest beta or something
senotrius said:
turn off pulse notification in settings,think its under display.
turn by turn-there's a modded google maps app in the forum.under apps section.
I don't use swype but same ques was asked before and I read u hv to download the latest beta or something
Click to expand...
Click to collapse
I find that the stock keyboard is not the best. I've read that its predictive text and spell corrections is supposed to be good, but it looks like it's not picking up anything at all and it's not correcting any spelling. What gives?