So first of all I tried to install some rom on my HTC Topaz (it wasn't the first time I change roms) and something gone bad, the installing was stuck on 0% , after the reboot the phone was stuck at launching.
I tried many suggestions that I found here on the forum, but nothing helped, I did the format+reset with MTTY.
Tried to install different roms from the bootloader but it always stuck on the 0% even tried to install them from SD card...
So now I'm in bootloader and it written -
_________________________________________
TOPA100 32M
SPL -1.33.0000
Microp-Topaz (LED) v10
TURBO HW/TURBO SW
--------------------------------------------
NO TP MFG DATA
Serial
_________________________________________
So what I can do now to bring it back?
Mark N1 said:
So first of all I tried to install some rom on my HTC Topaz (it wasn't the first time I change roms) and something gone bad, the installing was stuck on 0% , after the reboot the phone was stuck at launching.
I tried many suggestions that I found here on the forum, but nothing helped, I did the format+reset with MTTY.
Tried to install different roms from the bootloader but it always stuck on the 0% even tried to install them from SD card...
So now I'm in bootloader and it written -
_________________________________________
TOPA100 32M
SPL -1.33.0000
Microp-Topaz (LED) v10
TURBO HW/TURBO SW
--------------------------------------------
NO TP MFG DATA
Serial
_________________________________________
So what I can do now to bring it back?
Click to expand...
Click to collapse
wow NO TP MFG DATA sounds bad.
is the error code error 244? or another?
(or if flashing from SD card, it should show a red number, what is the number?)
There is no errors, it's just stopes at 0% and then the phone restarts.
I heard that I need to use a 6.1 original rom, I tried few from the shipped roms on the topaz-XDAwiki , and there is a change - they stuck after 1% and not 0% ...
Maybe I need to use a different type of rom?
---
Some original roms give a 294 error (wrong rom for this phone or something)
Mark N1 said:
There is no errors, it's just stopes at 0% and then the phone restarts.
I heard that I need to use a 6.1 original rom, I tried few from the shipped roms on the topaz-XDAwiki , and there is a change - they stuck after 1% and not 0% ...
Maybe I need to use a different type of rom?
---
Some original roms give a 294 error (wrong rom for this phone or something)
Click to expand...
Click to collapse
You need to find your original ROM from HTC.com using your S/N. Hopefully they are still available.
Mark N1 said:
There is no errors, it's just stopes at 0% and then the phone restarts.
I heard that I need to use a 6.1 original rom, I tried few from the shipped roms on the topaz-XDAwiki , and there is a change - they stuck after 1% and not 0% ...
Maybe I need to use a different type of rom?
---
Some original roms give a 294 error (wrong rom for this phone or something)
Click to expand...
Click to collapse
error 294 is CID error. we can try a goldcard (PM me for one) but I suspect that the TP MFG DATA also needs to be restored so goldcard on its own may not be enough to fix it.
So how do I restore the TP MFG DATA ?
Problem solved.
On the HTC.com I needed to choose the right region - so I guessed right at the 3rd guess (Thailand) - wrote the SN and downloaded the official rom, now the phone works fine .
Thank you guys.
Related
Hi all,
This morning I wanted to flash the new HTC ROM.
Flashed: RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship (Succesfull)
Restore_Stock_SPL_114_2.zip (Succesfull)
But then my deviece rebooted and now it shows:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
____________________________________________________________
Blackstone_CustomRUU_v1.0
Gives me Error: 292 Invalid Vender ID
HDa4-BMCF5567-HUEbc568-BMCF55670
____________________________________________________________
I tried USPL but gives a error that deviece is not responding
I tried several spl's, nothing hard spl, nothing...
Several coocked and shipped roms nothing...
Some cases it goes to flashing screen but stays at 0%
and some cases it goed to flashing screen goes to 1% and then gives the error...
Can someone help me?
have you just tryed with mtty tool ?(it reset you doc),it works with jasjar.
babak said:
have you just tryed with mtty tool ?(it reset you doc),it works with jasjar.
Click to expand...
Click to collapse
Babak jan,
mtty khatarnak hastesh....
mikham yek lahze waysam.
EN:
Mtty is kinda dangerous,
I'ma wait for some other tips before using mtty.
xmoo said:
Hi all,
This morning I wanted to flash the new HTC ROM.
Flashed: RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship (Succesfull)
Restore_Stock_SPL_114_2.zip (Succesfull)
But then my deviece rebooted and now it shows:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
____________________________________________________________
Blackstone_CustomRUU_v1.0
Gives me Error: 292 Invalid Vender ID
HDa4-BMCF5567-HUEbc568-BMCF55670
____________________________________________________________
I tried USPL but gives a error that deviece is not responding
I tried several spl's, nothing hard spl, nothing...
Several coocked and shipped roms nothing...
Some cases it goes to flashing screen but stays at 0%
and some cases it goed to flashing screen goes to 1% and then gives the error...
Can someone help me?
Click to expand...
Click to collapse
USPL was not working for me when I needed to use it to upgrade the ROM on my touch hd.
What I did was run it on Windows XP instead of Windows Vista and the device responded.
Install ActiveSync 4.5 on Windows XP, disable USB connection in ActiveSync settings, and connect PDA to computer via USB whilst the PDA is on bootloader.
Then run USPL.
prank1 said:
USPL was not working for me when I needed to use it to upgrade the ROM on my touch hd.
What I did was run it on Windows XP instead of Windows Vista and the device responded.
Install ActiveSync 4.5 on Windows XP, disable USB connection in ActiveSync settings, and connect PDA to computer via USB whilst the PDA is on bootloader.
Then run USPL.
Click to expand...
Click to collapse
Well the first try failed.
the phone didn't get connected to xp (using vmware)
So gonna try @ home.
I'm going to try this:
No connection, wait 5 min, than put battery back and preform a HR.
xmoo said:
Well the first try failed.
the phone didn't get connected to xp (using vmware)
So gonna try @ home.
I'm going to try this:
No connection, wait 5 min, than put battery back and preform a HR.
Click to expand...
Click to collapse
This didn't help......
Gonna try the xp method when I get back 2 home
xmoo said:
This didn't help......
Gonna try the xp method when I get back 2 home
Click to expand...
Click to collapse
You tried flashing your carrier's stock ROM (if available)?
Ta
Dave
DaveShaw said:
You tried flashing your carrier's stock ROM (if available)?
Ta
Dave
Click to expand...
Click to collapse
This was unbranded.....
But going to try to flash the dutch rom.
Funny thing is sometimes it starts flashing but after 1% the screen goes black and back to home menu of bootloader.
Most of the times it just stays @ 0%
xmoo said:
This was unbranded.....
But going to try to flash the dutch rom.
Funny thing is sometimes it starts flashing but after 1% the screen goes black and back to home menu of bootloader.
Most of the times it just stays @ 0%
Click to expand...
Click to collapse
Fire up MTTY and do an "info 2". It should give you the CID of the device - try and find a matching Ship EXE for that CID.
*Instructions for MTTY are in the Kaiser Stuck in Bootloader link in my sig BTW.
Ta
Dave
DaveShaw said:
Fire up MTTY and do an "info 2". It should give you the CID of the device - try and find a matching Ship EXE for that CID.
*Instructions for MTTY are in the Kaiser Stuck in Bootloader link in my sig BTW.
Ta
Dave
Click to expand...
Click to collapse
I don't know if it is you or what else.
This time bootloader said loading.....
While loading I ran the dutch rom update.
And now it's flashing.
IT WORKS!!!!!
RUU_BlackStone_HTC_NLD_1.14.404.3_Radio_52.49a.25.26_1.09.25.14_Ship
xmoo said:
I don't know if it is you or what else.
This time bootloader said loading.....
While loading I ran the dutch rom update.
And now it's flashing.
IT WORKS!!!!!
RUU_BlackStone_HTC_NLD_1.14.404.3_Radio_52.49a.25.26_1.09.25.14_Ship
Click to expand...
Click to collapse
The dutch image must match the CID / Model on your device.
Glad it's sorted.
Dave
xmoo said:
Babak jan,
mtty khatarnak hastesh....
mikham yek lahze waysam.
EN:
Mtty is kinda dangerous,
I'ma wait for some other tips before using mtty.
Click to expand...
Click to collapse
Khosh hala ke hal shod moshkelet ham shahri
Eng: I am very pleased that you resolved
xmoo said:
Hi all,
This morning I wanted to flash the new HTC ROM.
Flashed: RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship (Succesfull)
Restore_Stock_SPL_114_2.zip (Succesfull)
But then my deviece rebooted and now it shows:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
____________________________________________________________
Blackstone_CustomRUU_v1.0
Gives me Error: 292 Invalid Vender ID
HDa4-BMCF5567-HUEbc568-BMCF55670
____________________________________________________________
I tried USPL but gives a error that deviece is not responding
I tried several spl's, nothing hard spl, nothing...
Several coocked and shipped roms nothing...
Some cases it goes to flashing screen but stays at 0%
and some cases it goed to flashing screen goes to 1% and then gives the error...
Can someone help me?
Click to expand...
Click to collapse
I have the same problem only my message reads
RUUNBH
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error, Please Try Again.
Glad to read you resolved your problem however I'm stuck please help any advice would be apprecaitted
in mtty, command: set 16 0
will fix it
riz157, try flashing with the original shipped rom the device came with. i had this problem a few days ago. it took a while to work out. the shipped rom did the trick for me.
Oh man
I think I also screwed up my HD. It is stuck on Loading... screen. Won't connect to pc. Can not flash anything to it. Restores ok but after reset it shows "update rom code error,please try again" and then next screen shows Loading... for ever.
Please help me guys.....
Thanks a lot
i have the same problem, upgrade rom code error spl-1.54.0000
please can you help me
thank you
alex5552 said:
i have the same problem, upgrade rom code error spl-1.54.0000
please can you help me
thank you
Click to expand...
Click to collapse
Flash the original rom what came with ur Touch HD!
xmoo said:
Flash the original rom what came with ur Touch HD!
Click to expand...
Click to collapse
what if you dont remmember what was the original one =)
i tryed to delete the HSPL
by hardboot via SD ( LEOIMG )...
i got the same problem ...
with the message:
Upgrade ROM code error, Please Try Again.
1) i took out the SD from the Device
2) pulled out the battery 5 sec wait ...
3) put it back ... Push power button ...
4) on the exclamation mark screen ( after it loads )
5) reinstall the HSPL ...
and wm workes again ....
BUT STILL ....
how can i delete the HSPL properly and put a OWWE on my device.
Tictac0566 said ones i have : ( the original that was on my device )
Quote:
"Well, at least the ROM version is the official Hong Kong ROM for the HD2, including the Radio ROM version."
where to get the Hong Kong ROM =)
RUU_BlackStone_HTC_NLD_1.14.404.3_Radio_52.49a.25. 26_1.09.25.14_Ship
Where can I download this ROM
Rapidshare don't have it no more
Can someone upload this 4 me please
Thanks
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Before I flashed my first rom, I read wiki.xda-developers.com to make sure I understood what I was doing, and used the search button, instead of risking turning my phone into a paper weight.
Since then, Crackwhore has written a very helpful post at the top of this forum about how to use HSPL and USPL to allow you to flash roms.
yeah i know all that. not my first time flashing a phone but the first time it got stuck loading the bootloader. and specially when i´ve only used the HTC update.
darfor said:
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Click to expand...
Click to collapse
you mean you couldn't get to boot loader page?
So you already have HSPL 1.56 installed (or have SPL1.54 and used USPL)?
If you have HSPL you could try renaming the .nbh file to blacimg.nbh and copying it to the SD card and entering bootloader
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
AFW said:
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
Click to expand...
Click to collapse
try dnloading the rom again amd try.
the file might be corrupt
Have tried that many times. File is not corrupt. I'm getting really worried this is now a brick...
OK, if you can get phone into bootloader, it is not bricked
What does your SPL say in bootloader? Do you get any errors when trying to flash rom? Are you using USPL or HSPL? If USPL, you have to use it before every flash to new rom or radio. If HSPL, are you using correct version?
Was on Dutty's 3.9 XT, but decided to revert to standard WWE 1.56. I flashed the Std 1.56 ROM successfuly, and then tried to restore the ship SPL 1.54 using the card flash method. This failed, and now I'm stuck on the bootlader screen forever.
No matter what I do the THD always goes to bootloader (red-green-blue-white screen), with following text:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error
Please try again
USB
Click to expand...
Click to collapse
When I start blac_uspl.exe (USPL 2.5), a window flashes (Vista64) for a split second and then nothing else happens. The Vista64 system's USBs work with THD and have been used to sync over past few months.
When I try to run HSPLWrapper_Blackstone_156OliNex.exe and step through the preliminary screens, the Verify that you want to update ROM version screen has the From Image Version as blank and the To Image Version as 1.56.Olinex. When I click to commit the flash the THD screen switches to white with a progress indicator that always stays at 0% until it times out. Recovery does nothing and the same thing always happens. Using Vista64. .Net installed and fine. I can't use the card method (BLACIMG.NBH) - the system also stays on "Loading .... 0%" and nothing else happens.
When I try to flash anything (have tried HSPL1.56, Dutty's 3.9 ROM, stock 1.54 spl) using the card method, the system says "Loading . . ." and hangs there forever without a progress indicator showing.
Your SPL says 1.54.0000. When you try and run USPL.exe have you remembered to disable your antivirus?
Have you tried usb method instead of card for flashing rom?
I know you have said that youi have used usb for syncing, but when in bootloader does it change from 'serial' to 'usb' when you connect HD to PC?
Fallen Spartan - I want to thank you for taking the time to help me resolve this problem. Very much appreciated!
1. Yes, anti-virus disabled and indeed removed from the PC.
2. Yes, have tried the USB method at least 20 times.
3. Yes, the bootloader changes from Serial to USB. It then goes to the progress indicator screen and hangs on 0%. The progress indicator on the RUU on PC also stays at 0% and eventually times out. I've gone through the Recovery routine at least 20 times, with no luck.
When I try to run SSPL-Manual-TouchHD.exe it says "not a valid Win32 application".
I'm a bit perplexed by this.
You have obviously successfully flashed Duttys V3.9 so drivers are fine, you know how to use USPL, both flashing methods (SD card and usb/pc), disabled anti-virus, phone in bootloader.
Have you tried to reflash 1.56 rom or possibly performing a hard reset before trying to use USPL or HSPL. I doubt this would make a difference though.
Have you tried cRaCKwHoRe's USPL GUI v 2.5 Application?
You don't get any code errors?? I'm struggling to find a solution here.
Yes, this is most vexing. I've flashed innumerable times before and never had an issue. I suspect the SPL is fine, but somehow the actual WM ROM image is corrupted. Will now try to load Std 1.56 ROM image again...
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa (though I'm a rugby fan).
AFW said:
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa.
Click to expand...
Click to collapse
No accomodation required, just glad you got it sorted
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
can anybody help me at all
Adamsville: perhaps you're stuck in bootloader mode because the WM ROM image flashed on your system has become corrupted or disabled, ie the only thing the system can boot into is the bootloader.
Try flashing a new compatible WM ROM image and see if that works.
AdamsvillE said:
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
Click to expand...
Click to collapse
a hardreset followed by a 1.54 base rom will solve all ur probs.
or lower spl to 1.14 cos ur stock rom is a 1.14 base as suggested by th name..
cheers
Hi.
In short: After normal using my Diamond just reset himself and screen was snowing, some pixels etc.
When I'm going to bootloader screen is ok, without snowing or something and says:
DIAM100 64M
SOL-2.07.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
Serial
When I plugged usb cable SERIAL changing to USB - so far so good...
I'm using VISTA, I hear sound when I plugging Diamond, ROM Update Utility see device because starting to install Hard SPL but progress is stuck on 0%...
Windows Mobile Device Center cannot see device.
Windows doesn't see device as a removeble disk so I CAN'T COPY NOTHING to my device...
What to do?
I was trying many different HardSPL but nothing... always 0%
Please help....
Look here:
http://forum.xda-developers.com/showthread.php?t=409425
yeah, but like I said I can't synchronize phone with windows.
WMDC doesn't see my phone.
Ok,
because it's UK phone from O2 I think that I need shipped rom.
I've tried
Xda Ignit2_UK_2.10.206.1_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_Ship
but it's error after 1%
Error 244
Invalid model ID.
My phone P/N is 99HEJ105-00
When I try to download ROM from HTC website and I put my S/N then it says that my model is incompatible with these ROMs...
Which ROM I have to install?
Helo
madmadig said:
Ok,
because it's UK phone from O2 I think that I need shipped rom.
I've tried
Xda Ignit2_UK_2.10.206.1_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_Ship
but it's error after 1%
Error 244
Invalid model ID.
My phone P/N is 99HEJ105-00
When I try to download ROM from HTC website and I put my S/N then it says that my model is incompatible with these ROMs...
Which ROM I have to install?
Helo
Click to expand...
Click to collapse
Wait...Have you previously unlocked and flashed to a custom rom?
If not, then you have the shipped rom on your device. In that case, hard reset to remedy your initial problems.
If you are trying to unlock and flash a custom rom then please read and learn as much as you can before you brick your device and really regret it.
mr.horndoctor said:
Wait...Have you previously unlocked and flashed to a custom rom?
Click to expand...
Click to collapse
No, I didn't. I didn't do anything with my phone...
mr.horndoctor said:
If not, then you have the shipped rom on your device. In that case, hard reset to remedy your initial problems.
Click to expand...
Click to collapse
How can I do this? I can't install any ROM, any HardSPL. The thing is that under battery I have DIAM300 but in bootloader i have this:
DIAM100 64M
SOL-2.07.0000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
mr.horndoctor said:
If you are trying to unlock and flash a custom rom then please read and learn as much as you can before you brick your device and really regret it.
Click to expand...
Click to collapse
Ok, I will, but in the meantime I can't do nothing even brick my phone
Look here:
http://wiki.xda-developers.com/index.php?pagename=Diamond_For_Beginners
Lots of great info in the Wiki!
Ok, thanks,
but I still can't find ROM for my phone...
All ROMs are stopping on 1% because I need shipped ROM for my phone.
How can I find it?
madmadig said:
Ok, thanks,
but I still can't find ROM for my phone...
All ROMs are stopping on 1% because I need shipped ROM for my phone.
How can I find it?
Click to expand...
Click to collapse
Until you unlock, the only rom you can flash is the stock shipped rom like the rom that is already on your device.
If you can hard reset and your device functions normally, then there is no reason to re-flash the stock/shipped rom. Just hard reset.
Here is the Wiki page with shipped roms:
http://wiki.xda-developers.com/index.php?pagename=Diamond_Upgrades
mr.horndoctor said:
Until you unlock, the only rom you can flash is the stock shipped rom like the rom that is already on your device.
If you can hard reset and your device functions normally, then there is no reason to re-flash the stock/shipped rom. Just hard reset.
Here is the Wiki page with shipped roms:
http://wiki.xda-developers.com/index.php?pagename=Diamond_Upgrades
Click to expand...
Click to collapse
I can do HR but my original ROM doesn't working. When i push vol up or vol down phone is formatting and restarting but the white screen appears and that's it...
I've tried HTC Europe version (fifth from top) and UK O2 version. Best thing is that they are going to 1% so it is not 0%
Error is Invalid Model ID or (second) invalid VENDOR.
I've tried to change ROM's device ID in NBH utility but it doesn't work and it's not even 1% after this operation.
Second thing is that under battery i have DIAM300 but in bootloader DIAM100...
I think that I just need correct ROM, but I've tried a lot of them and nothing.
Why when i'm changing Model ID for DIAM***** in NBH it doesn't works?
Next thing- when I'm doing HR with arrow then on screen appears couple texts and one says NO IMAGE FILE,
I think that means that ROM on my phone is broken..
It looks like, at some point, the wrong rom/spl was flashed to your device. I believe this is your shipped rom:
http://www.mediafire.com/?jnjydmnnojg
Make sure that nothing else is running in the background on your computer that might interfere with the flashing process or block communication between your computer and your device like a firewall, virus protection, port blocking or anything else.
Good Luck!
mr.horndoctor said:
It looks like, at some point, the wrong rom/spl was flashed to your device. I believe this is your shipped rom:
http://www.mediafire.com/?jnjydmnnojg
Make sure that nothing else is running in the background on your computer that might interfere with the flashing process or block communication between your computer and your device like a firewall, virus protection, port blocking or anything else.
Good Luck!
Click to expand...
Click to collapse
Error. Invalid Device ID.
I'm doing everything like in this post.
I have error Invalid Model ID so I changing it by NBH utility.
Before I was changing it my update was 1% and error Invalid Model ID.
I've changed only Model ID, rest of stuff I didn't touch.
After I've changed Model ID it is not even 1% update- it's 0% and UPDATE error...
When I try to install other ROMs, from HTC for example then I have error invalid VENDER.
Help guys!
I guess the only other thing you could do is format with MTTY which would totally wipe the OS but I think you have to have a hard spl installed first in order to do that. I'm not that familiar with MTTY.
RATS!! I thought I found the rom you needed because if it says DIAM300 in the battery compartment then I thought that should be the one you need.
You said when you put it in bootloader it says DIAM100 and I'm betting that it should say DIAM300 like it says on the device.
Well maybe someone else has a suggestion.
I did MTTY format.
But nothing changed.
Still errors, Invalid Device ID or Vendor.
Next thing- when I install HTC USB drivers it isn't changing from 2007 to 2003 but to 2004. I have run my Vista without Signing drivers (F8) and when I'm installing these drivers from topic about MTTY I have only one driver available and it is Digitally signed- should it be unsigned ?
Help me guys!
hello!i have an htc touch diamond 2 and i used hard-SPL in order to put a new rom to my device.i did it successfully(at least pc said so) and then i installed a rom energy topaz successfully too.but when it was done my device restarted on its own and it cant boot.the only thing that it does is to appear the htc green logo in white screen and then restarting again and again and again!!i kept the volume down button and it booted on the red-green-blue-white screen and it says this:
TOPA100 32Μ
SPL-2.51.oliNex ------>on the red part
MicroP-Topaz (led) V10
TURBO HW/TURBO SW
TPMFG DATA
517,557 190,896
186,212 854,214 --------->this one one green part
847,894 calibrated
and on the white part it says usb when its connected with pc and serial when its not!!what can i do now?i tried also some other roms for topaz which were succefully loaded too but the same thing happens again and again.i would apriaciate some help.
thanx.
billyprepo said:
hello!i have an htc touch diamond 2 and i used hard-SPL in order to put a new rom to my device.i did it successfully(at least pc said so) and then i installed a rom energy topaz successfully too.but when it was done my device restarted on its own and it cant boot.the only thing that it does is to appear the htc green logo in white screen and then restarting again and again and again!!i kept the volume down button and it booted on the red-green-blue-white screen and it says this:
TOPA100 32Μ
SPL-2.51.oliNex ------>on the red part
MicroP-Topaz (led) V10
TURBO HW/TURBO SW
TPMFG DATA
517,557 190,896
186,212 854,214 --------->this one one green part
847,894 calibrated
and on the white part it says usb when its connected with pc and serial when its not!!what can i do now?i tried also some other roms for topaz which were succefully loaded too but the same thing happens again and again.i would apriaciate some help.
thanx.
Click to expand...
Click to collapse
Sorry i didn't get back to you sooner and you added the perfect amount of info
ok where to start - firstly have you tried a hard reset after flashing the ROM this isn't always needed but may possibly free something up to make the energy ROM work. You could also try flashing back to a stock ROM from the HTC website and then re-flash the one you want after everything is ok on the stock ROM.
when you say successfully loaded do you mean the screen shows 100% (phone not computer) or does it say complete as it can say 100% on the screen for a little while and not work ? I don't do mine by the PC i use a memory card to flash it and mine always comes up complete when done and then press a key to restart the phone.
failing all of this head back into the hard_spl thread run the spl_relocker in the first post and once relocked flash with hard_spl 1.83 no idea if the newer version is less or more buggy but i use 1.83 and it's smooth sailing.
You could also try flashing from a memory card instead if you have one to hand
thanx warlordxxx!its done!
billyprepo said:
thanx warlordxxx!its done!
Click to expand...
Click to collapse
No problemo
here is my problem. yesterday i tried to flash Shaks.Pv4.30Full_DiamondKB rom, from ROM.dia.1.7.0_100625. i did mtty (task 29) and started to flash as i did many times before.
however at 6% flash my hdd decided to make an epic fail, and died. after i sorted out my computer (new hdd, new win7...) i did mtty again (worked fine) and tried to flash. however (at 1%) now i get error 226:
when i reset phone goes directly into bootloader and gives: "Upgrade ROM code error. Please try again"
i have tried to flash Gen.Y D2 R5.5 WWE, RaL.GT1K, ROM.dia.1.7.0_100625, Duttys_5.2.20764.1.4.3_V4_Full_CVSD__3.02_, RUU_Diamond_HTC_WWE-ME_1.37.456.2_Radio_Signed_Diamond_52.26a.25.09_1.00.25.03_Ship (stock diamond), RUU_Victor_TMO_UK_1.37.110.3_Radio_Signed_Diamond_52.26a.25.09_1.00.25.03_Ship (stock mda compact 4), and tlr-diamond-3.08.07.16.
all other roms fail at 1%, but tlr rom fails at 16%, and stock diamond and mda roms fail at 13%.
my phone is mda compact 4. before i have flashed hardspl olinex 1.93 unsigned, and radio 1.17 (from blackstone).
at the moment i really don't know what should i do next (i'm hoping it's not completely lost because i can get into bootloader), so any help would be appreciated.
Damn... This is Harsh.. I Hope someone can provide you with a solution.. I'm subscribing to this thread just in case something like this happens to me also
well, officially, my mda compact was bricked
but fear not, it can be resurrected, via JTAG (some shop did it for a price)...
however i do have a question, now when i enter bootloader it says:
DIAM100 64M
RIFFBOX RESURRECTED!
PSOC-Vict Stage_PVT v0x20.
now i wonder if it's ok to flash again unsigned HardSPL, and custom rom?