Related
Q&A for the MIUI rom
MIUI beta 8 for captivate---plz help urgently
miui beta 8 can not find any sim card in my captivate. trying to flash back to 2.2 but cant get CWM or download mode to work. Tried all 3 button tricks. Did not work. Please help urgently
chemisam said:
miui beta 8 can not find any sim card in my captivate. trying to flash back to 2.2 but cant get CWM or download mode to work. Tried all 3 button tricks. Did not work. Please help urgently
Click to expand...
Click to collapse
Wow , that's wierd . I flashed beta 8 with no problems .
Ummm ... assuming you've done ALL possible 3 button tricks , did you try going into airplane mode ?
You've probably already done this , but just making sure , did you try rebooting the phone ?
Just curious , what were your steps to flash MIUI ? And how do you normally go to download mode ?
actually i followed the exact same procedure in the miui forum and also I was in 2.2 based roms. download mode worked when I was flashing miui rom. But does not work anymore
BTW I go to download mode by holding the up and down vol button together and then plugging in the USB cable to the phone
chemisam said:
BTW I go to download mode by holding the up and down vol button together and then plugging in the USB cable to the phone
Click to expand...
Click to collapse
What is the kernel on your phone, settings/system/about phone select more info
MIUI
karnel is speedmod-kernel-k13c-500hz
version: 2.6.35.7-g99995d1
erm, your supposed to have a cm7 kernel or a variant of it....
your sposed to flash the speedmod kernel
then flash the efsbackup file
then flash the cm7 kernel
then flash miui...
chemisam said:
karnel is speedmod-kernel-k13c-500hz
version: 2.6.35.7-g99995d1
Click to expand...
Click to collapse
You messed up. if you can't get into dl mode you will need a jig
MIUI
Real long shot here
If you have wifi, dl sgs kernel flasher from market. Actually dl a compatible cm7 kernel. Use kernel flasher to try to flash kernel. Probably won't work cause sounds like you can't see your sd. Also did you flash the efs backup as stated in the instructions?
MIUI
right now i have soft bricked the phone
I tried all the tricks...my last hope is JIG
chemisam said:
actually i followed the exact same procedure in the miui forum and also I was in 2.2 based roms. download mode worked when I was flashing miui rom. But does not work anymore
Click to expand...
Click to collapse
chemisam said:
karnel is speedmod-kernel-k13c-500hz
version: 2.6.35.7-g99995d1
Click to expand...
Click to collapse
That means you didn't follow instructions properly . Try using the kernel flasher . And flashing one of the "[KERNEL][CM7] ...." kernels . MIUI is based off of the nexus S , and CM7 uses a captivate version kernel from Nexus S .
If all else fails , DL jig .
For the new Rc1 do you have to flash Beta 7 then Rc1 or can you go straight to RC1
Help
I followed all the steps and flashed MiuiCapPre1 and got it to work. I rebooted the device and I am now stuck in a endless reboot. All I see is Galaxy S Cyanogen mod screen and occasionally a At&t screen. I also can't seem to enter Download Mode I get the screen that looks like its about to display the battery.
Any suggestions how on how to fix this?
if this is answered im sorry, but i cant figure out out to get my contacts from my sim to show up or import them
...
why can i download any apss on the market ???
No Incoming Text Messages
hello I flashed the latest miui version (rc2) and I am not receiving text messages. I can send them out but I just cant receive any. Anyone have any advice? everything else seems to be working correctly. Appreciate any help! Btw, this is my first time flashing the miui on the captivate.
wibi795 said:
why can i download any apss on the market ???
Click to expand...
Click to collapse
go to the app downloads and push the menu button and select download using mobile network.
So I flashed RC2 and it came up as I9000 device. I flashed TheEscapists 4.2 kernel and it changed to his kernel but kept the device as I9000? I have not had time to keep up with the thread like I normally do so is this an issue that is known or just a single occurrence?
Wow lol didn't even know we had one of these, if you have questions then you should read the FAQ section in the third post of the MIUI thread otherwise you might as well post your question on the thread rather than here as it will be answered a lot faster.
Sent from my SAMSUNG-SGH-I897 using XDA App
If you have more than 10 posts its a better idea to ask ur questions in ROM thread, else this thread is for you.
Safe Flashing from Gingerbread
Thank you for starting this thread
I am currently running Apex 6.3 and want to flash to a newer rom, Apex 7.
I have a Rogers phone I896 and so I no longer have my volume buttons working to put it in to recovery or download mode, I have read not to load any kinda fix for that(something about two boot loaders being a bad idea).
My understanding is that I have to go back to stock before flashing a new rom(I have seen you have roms that can be upgraded rather then re-flashed) but I want to wipe my internal sd card and flash like new.
Do I just use ODIN 1 click and go back to stock and use it to clean my sd card, is that a safe option or am I missing something?
If I remember correctly I had to do like 2 or 3 steps to flash Gingerbread from from stock rom, load boot loaders, load kernel, load rom. So I am wondering if it is 1 step to go back to stock ?
I know I have seen a post on a thread on this but to find it when needed is not so easy, XDA-Developers has grown big time since I started with WM5(Android is all new to me)
Hi I had a question concerning running new boot animations for APEX 7 with Update-1 package.
I found this boot animation http://forum.xda-developers.com/showthread.php?t=1121014 that I would like to install but it seems as though it isn't working. Is it possible with this ROM to get new boot animations?
Thank You
So you can't put the phone into download mode?
Odin 1 click is pretty straight forward from what I remember. First I boot up the phone normally and hit "master clear". Second I put the phone into download mode and hit the "Start" button which goes and installs the stock firmware. Obviously you need to be in debug mode to do all this so make sure you're good with that.
I don't know if you already have it but here is a link for the Odin 1 click I use.
http://forum.xda-developers.com/showthread.php?t=731989
Johndoe205 said:
Hi I had a question concerning running new boot animations for APEX 7 with Update-1 package.
I found this boot animation http://forum.xda-developers.com/showthread.php?t=1121014 that I would like to install but it seems as though it isn't working. Is it possible with this ROM to get new boot animations?
Thank You
Click to expand...
Click to collapse
Will have to wait for boot animations to work buddy, as of now kernels dont support it
If you are already on ApeX 6.x you can flash 7 using CWM.. No need to ODIN back to JF6.
In worst case if u have to ODIN back that should be to stock GB.
But as i said just flash 7 on top of 6.3 by going into recovery mode
Gazoo222 said:
Thank you for starting this thread
I am currently running Apex 6.3 and want to flash to a newer rom, Apex 7.
I have a Rogers phone I896 and so I no longer have my volume buttons working to put it in to recovery or download mode, I have read not to load any kinda fix for that(something about two boot loaders being a bad idea).
My understanding is that I have to go back to stock before flashing a new rom(I have seen you have roms that can be upgraded rather then re-flashed) but I want to wipe my internal sd card and flash like new.
Do I just use ODIN 1 click and go back to stock and use it to clean my sd card, is that a safe option or am I missing something?
If I remember correctly I had to do like 2 or 3 steps to flash Gingerbread from from stock rom, load boot loaders, load kernel, load rom. So I am wondering if it is 1 step to go back to stock ?
I know I have seen a post on a thread on this but to find it when needed is not so easy, XDA-Developers has grown big time since I started with WM5(Android is all new to me)
Click to expand...
Click to collapse
First off I want to say thank you for making an awesome ROM. Loving it thus far and has been running flawlessly except for one minor issue I ran into tonight. For the MIUI lockscreen the phone freezes then goes to the android boot animation screen and right back to the MIUI lock screen whenever I try to unlock with SMS unlock. Is this a known issue with the screen unlock concerning MIUI?
Sent from my I897 using XDA App running APEX 7 Update-1
Johndoe205 said:
First off I want to say thank you for making an awesome ROM. Loving it thus far and has been running flawlessly except for one minor issue I ran into tonight. For the MIUI lockscreen the phone freezes then goes to the android boot animation screen and right back to the MIUI lock screen whenever I try to unlock with SMS unlock. Is this a known issue with the screen unlock concerning MIUI?
Sent from my I897 using XDA App running APEX 7 Update-1
Click to expand...
Click to collapse
U have not set custom app for lockscreens. clicking on message icon takes u to custom app u select and since u have not selected it reboots.
See ROM OP on how to do it.
Thanks for ur feedback buddy
Awesome!! Everything is perfect now =) can't wait for your next update! Gonna donate now. Keep up the amazing work!!
dear sir
hey! amazing job on this one looks really promising! I have GR-12 on my cappy with the latest talon kernel and GB bootloader. my question is, if i want to install this do i need to flash back to stock 2.1 and do the entire process (reinstall talon and bootloader then install your rom)? OR can i just enter recovery mode with my phone currently using gr-12 and use CWM to install APEX 7 rom? either way i have to first install apex 7 then use cwm to install update 1 directly after correct?
adamm1 said:
hey! amazing job on this one looks really promising! I have GR-12 on my cappy with the latest talon kernel and GB bootloader. my question is, if i want to install this do i need to flash back to stock 2.1 and do the entire process (reinstall talon and bootloader then install your rom)? OR can i just enter recovery mode with my phone currently using gr-12 and use CWM to install APEX 7 rom? either way i have to first install apex 7 then use cwm to install update 1 directly after correct?
Click to expand...
Click to collapse
All you gotta do is put apex on your sd card then go into setting and privacy and do a factory reset then reboot into recovery clear the cache and dalvic cache then install apex
EDIT Do the factory reset then put the ROM on your SD card lol
PLEASE HELP ME PLEASE BEEN UP 48hr researching
Installed Apex_7 on my phone and i used a kernal swap to bypass the froyo file verification instead of going back to eclair first. after i got all working and installed Apex i rebooted my phone the at&t logo came up then the screen went all crazy and then kept replaying the galaxy s animation so then i used odin to go back to stock after odin said success i rebooted the phone and now im stuck at the at&t logo. cant get into download mode
AND i have made a usb jig but it does not work i tried 3 100k resistors and 3 100k and 1 1k and still nothing. Also if i take a ohm meter it will only read up to 2 resistors at a time once i add the 3rd one i get a split second reading then nothing but ive tested them all by there self and they read 0.10 and 2 reads 0.20 then 3 reads 0.30 for a split second then reads nothing.
Thanks anyhelp greatly appreciated!!!!!!!!!!
I dont wanna make this my new paper weight.
Watsaa, first off I have to say this is an awesome rom. I have tried other GB roms and this one just rocks. I am running Apex 7 update 1 and the only issue I had was everytime I returned to the launcher it seem to reload all the icons and widgets. Then i flashed Talon 2.2 and wow!! It runs much better and no more reloading of the launcher. Smooth as butter.
mfd624 said:
Watsaa, first off I have to say this is an awesome rom. I have tried other GB roms and this one just rocks. I am running Apex 7 update 1 and the only issue I had was everytime I returned to the launcher it seem to reload all the icons and widgets. Then i flashed Talon 2.2 and wow!! It runs much better and no more reloading of the launcher. Smooth as butter.
Click to expand...
Click to collapse
thanks buddy
yaboydrew said:
Installed Apex_7 on my phone and i used a kernal swap to bypass the froyo file verification instead of going back to eclair first. after i got all working and installed Apex i rebooted my phone the at&t logo came up then the screen went all crazy and then kept replaying the galaxy s animation so then i used odin to go back to stock after odin said success i rebooted the phone and now im stuck at the at&t logo. cant get into download mode
AND i have made a usb jig but it does not work i tried 3 100k resistors and 3 100k and 1 1k and still nothing. Also if i take a ohm meter it will only read up to 2 resistors at a time once i add the 3rd one i get a split second reading then nothing but ive tested them all by there self and they read 0.10 and 2 reads 0.20 then 3 reads 0.30 for a split second then reads nothing.
Thanks anyhelp greatly appreciated!!!!!!!!!!
I dont wanna make this my new paper weight.
Click to expand...
Click to collapse
what key combo you tried? if u can see ur phone turn on then its not bricked
i tried to install Apex 7.1, but it stuck at the android logo screen for few hrs already... any help please
watsaa said:
what key combo you tried? if u can see ur phone turn on then its not bricked
Click to expand...
Click to collapse
Everything i even been trying with a homemade jig but no luck i dont get it.
Everyone keeps saying tho if you can see an at&t logo its not bricked.
but i followed exact instructions on making a jig.
dartore said:
i tried to install Apex 7.1, but it stuck at the android logo screen for few hrs already... any help please
Click to expand...
Click to collapse
im having the same prob keep checking this thread and the thread Brand new Bricked, a solution will arrise shortly with the great help among this site.
should i turn off my phone then? because it been there for so long already.
yaboydrew said:
Everything i even been trying with a homemade jig but no luck i dont get it.
Everyone keeps saying tho if you can see an at&t logo its not bricked.
but i followed exact instructions on making a jig.
Click to expand...
Click to collapse
you dont need a jig, its not bricked
Hi all,
Tried to flash ICS 4.0.3. Had flashed CM7 and it was working fine but the flash was purely so I could put ICS on, installed the zip through CWM but now it is bootlooping. I see the Galaxy S original bootscreen then what I am presuming is the custom ICS bootscreen then alot of CWM text with the android robot then the android robot dead with a phone through his chest
I have tried removing the battery a couple of times.
I am a bit of a newbie so any help is much appreciated
What shouls I do?
BTW I can get to download mode so flashing through odin is always a last resort but if ICS is redeemable then thats much preferred!
Josh, you didn't listen to my advice on your last post did you?????
I'm too drunk now, hopefully someone will be able to help you.
However if I were you, I'd pull the battery, get back into recovery, flash ics again and then it should boot fine. This has happened every time I have flashed ics and is well documented in the threads.
And next time read up some more before flashing.
woolf clubs said:
Josh, you didn't listen to my advice on your last post did you?????
I'm too drunk now, hopefully someone will be able to help you.
However if I were you, I'd pull the battery, get back into recovery, flash ics again and then it should boot fine. This has happened every time I have flashed ics and is well documented in the threads.
And next time read up some more before flashing.
Click to expand...
Click to collapse
Could not figure out how to get back into recovery mode and I needed a quick fix so I reflashed Darky via Odin as I had the files handy, I may try ICS again another time.
Thanks anyway.
JoshJoshJoshJosh said:
Could not figure out how to get back into recovery mode
Click to expand...
Click to collapse
When your phone is Boot looping like that, just press and hold Vol up + Home + power for about 10 seconds. The phone will then restart into Recovery. From there reflash the ICS build again.
Have been told on another forum that it is fine to go straight from any GB rom to ICS simply by flashing the kernel then the rom then again the kernel. So I could therefore go straight from 10.2 RE to ICS?
Is this true as it seems to contradict the guide in OneCosmic's post?
Whatever Rom I flash, I always follow that particular Dev's instructions. That way you avoid Boot Loops or Force Close errors!
How long should the initial boot of ICS take? Successfully flashed it (I think) but it seems to be on the fancy moving panel bootscreen thing for quite a long time. Is this normal?
Edit: Up and running, thanks to everyone who helped
Could not download from the market so I read around and noticed it was a common problem and that you neede to wipe data/factory reset now I am stuck in a bootloop and cannot get into recovery mode is there an exact way to press and release the buttons or is it a case of: take out battery, vol up home and power and just hold?
I find my newly purchased tab 8.9 very laggy with the stock TouchWiz
Before returning it I wanted ti try the Overcome rom to see if it can get any smoother.
I carefully followed there instructions but I am unable to go past the downloading droid. once I validate with the right button volume, the tablet simply reboots.
Does anyone else have this issue?
josibarns said:
I find my newly purchased tab 8.9 very laggy with the stock TouchWiz
Before returning it I wanted ti try the Overcome rom to see if it can get any smoother.
I carefully followed there instructions but I am unable to go past the downloading droid. once I validate with the right button volume, the tablet simply reboots.
Does anyone else have this issue?
Click to expand...
Click to collapse
Let me get this right: you sucessfully flashed Overcome, and want to ODIN but when you try to get in Download Mode, it reboots, is that it? If so, that's the first time I've heard this issue. How are you trying to enter Download Mode?
nirogu325 said:
Let me get this right: you sucessfully flashed Overcome, and want to ODIN but when you try to get in Download Mode, it reboots, is that it? If so, that's the first time I've heard this issue. How are you trying to enter Download Mode?
Click to expand...
Click to collapse
I am still with the Samsung original
I wanted to try the overcome ROM see if the lag disapears.
I am stuck in the first step when I need to flash CWR using Odin. I can't get into the download menu
josibarns said:
I am still with the Samsung original
I wanted to try the overcome ROM see if the lag disapears.
I am stuck in the first step when I need to flash CWR using Odin. I can't get into the download menu
Click to expand...
Click to collapse
I see. The Overcome thread also has the CWM Recovery as a .zip file which is flashable through Stock Recovery (same procedure as flashing Root). You just put the file in your internal SDcard and flash away. If you still have doubts, read a little bit here, as I'm sure that will clear any doubts you might have.
josibarns said:
I find my newly purchased tab 8.9 very laggy with the stock TouchWiz
Before returning it I wanted ti try the Overcome rom to see if it can get any smoother.
I carefully followed there instructions but I am unable to go past the downloading droid. once I validate with the right button volume, the tablet simply reboots.
Does anyone else have this issue?
Click to expand...
Click to collapse
u have to press the power and the left-volume button for about 15sec
nirogu325 said:
I see. The Overcome thread also has the CWM Recovery as a .zip file which is flashable through Stock Recovery (same procedure as flashing Root). You just put the file in your internal SDcard and flash away. If you still have doubts, read a little bit here, as I'm sure that will clear any doubts you might have.
Click to expand...
Click to collapse
Perfect it worked! And I was also able to install the Overcome ROM It seems to be more battery hungry and a bit faster
DonKomposto said:
u have to press the power and the left-volume button for about 15sec
Click to expand...
Click to collapse
Yes I have done that and I get to the menu with the droid blinking with "downloading" written under it. The issues is when I validate instead of showing the dowload menue it simply reboots...
josibarns said:
Perfect it worked! And I was also able to install the Overcome ROM It seems to be more battery hungry and a bit faster.
Click to expand...
Click to collapse
Don't expect perfection from a port, ever (port = a ROM that's not native to the device). The motley kernel, along with UV can help you in the battery department.
Sent from my GT-P7310
Sorry to comeback to it but after having flashed a couple or ROM with CWM I want to come back to the stock rom using ODIN and I cannot enter the dowload menu.
My system right now is a stock ROM us retail P7310UEKHA flashed with CWM and CWM and I want to install a 3.2 stock ROM using ODIN.
The way I try to access the download menu is
1. Turn off the tab
2. wait 30 sec
3. restart with the down volume pressed
4. when the reaching the menu between recovery and dowloading. Select dowloading with the down volume button and validate with the up volume button.
Result: a black screen for 3 seconds and then the tab reboots
josibarns said:
Sorry to comeback to it but after having flashed a couple or ROM with CWM I want to come back to the stock rom using ODIN and I cannot enter the dowload menu.
My system right now is a stock ROM us retail P7310UEKHA flashed with CWM and CWM and I want to install a 3.2 stock ROM using ODIN.
The way I try to access the download menu is
1. Turn off the tab
2. wait 30 sec
3. restart with the down volume pressed
4. when the reaching the menu between recovery and dowloading. Select dowloading with the down volume button and validate with the up volume button.
Result: a black screen for 3 seconds and then the tab reboots
Click to expand...
Click to collapse
A corrupt bootloader that may be. Reflash KHA (CWM version alterbridge posted) to see if it solves it.
Sent from my SGH-T959.
Just to precise this issue was present out of the box when I got it from best buy...
josibarns said:
Just to precise this issue was present out of the box when I got it from best buy...
Click to expand...
Click to collapse
flash a stock bootloader and a stock recovery using nvflash, im in a hurry now and dont have time to explain, use google, you will find all the info in the tab 10.1 forum.
lupu666ro said:
flash a stock bootloader and a stock recovery using nvflash, im in a hurry now and dont have time to explain, use google, you will find all the info in the tab 10.1 forum.
Click to expand...
Click to collapse
Thanks lupu666ro. I've tried installing stock Rom with CMW but nothing works. I have found very sparse info about nvflash. It looks like the solution but I'm a bit wary about tring this without a instructions. Could give me more info or point me to a tutorial
Thanks!
Still no luck...
So I have tried reflashing the stock US retail ROM and ran the EULA3 OTA update over it. I can't seem to figure this out.
The OTA update entered the download mode for a few seconds during the update so I am wondering if I don't simply have a locked bootloader.
I have made a video to show the problem: http://youtu.be/b09-x31ldbs
josibarns said:
So I have tried reflashing the stock US retail ROM and ran the EULA3 OTA update over it. I can't seem to figure this out.
The OTA update entered the download mode for a few seconds during the update so I am wondering if I don't simply have a locked bootloader.
I have made a video to show the problem: http://youtu.be/b09-x31ldbs
Click to expand...
Click to collapse
here is a tutorial on how to use nvflash, this will repair you tablet. http://forum.xda-developers.com/showthread.php?t=1130574
On the download warning screen you are hitting volume down, not up. Volume up is the button closest to the headphone jack..
josibarns said:
So I have tried reflashing the stock US retail ROM and ran the EULA3 OTA update over it. I can't seem to figure this out.
The OTA update entered the download mode for a few seconds during the update so I am wondering if I don't simply have a locked bootloader.
I have made a video to show the problem: http://youtu.be/b09-x31ldbs
Click to expand...
Click to collapse
Sent from my SAMSUNG-SGH-I957 using XDA App
neubauej said:
On the download warning screen you are hitting volume down, not up. Volume up is the button closest to the headphone jack..
Click to expand...
Click to collapse
Ok I am really ashamed on this one, you were right I've been hitting the wrong button for all my attempts
Thanks a lot neubauej!!!!!
Lol, no problem, glad it was simple.
Sent from my SAMSUNG-SGH-I777 using XDA App
Hi all, i've a problem with my Note, It stuck in Galaxy Note logo screen :-(
I was in ICS Stunner 1.4.19 version and it's happens when i fllash the new LP6 Rooted Kernel http://forum.xda-developers.com/showthread.php?t=1614435
from CWM.
My previous kernek was:
3.0.15-i9220ZCLP5-CL2955568
now it's impossible to access to the cwm with VolumeDown + Home + pwr ...
please HELP me !
Thx !
mapodres,
I think it is VolumeUp+Home+Power.
The_Steph said:
mapodres,
I think it is VolumeUp+Home+Power.
Click to expand...
Click to collapse
Right one
Sent from my GT-N7000 using xda premium
Yes sorry, but i can't enter on it
Just the download mode its working ...
What is my solution ?
I just flashed the same kernel with no issues
Try again pressing Power button+VolumeUp+Home button and do not let go of them even when you see the Galaxy Note screen, keep holding and hopefully you'll end up in recovery
Same problem, i've waited 3 mins but nothing, always stuck on GalaxyNote screen ...
mapodres said:
Same problem, i've waited 3 mins but nothing, always stuck on GalaxyNote screen ...
Click to expand...
Click to collapse
Then Odin is your only way out mate, sorry..
Try Odin
Working Solution (Please confirm)
mapodres said:
Same problem, i've waited 3 mins but nothing, always stuck on GalaxyNote screen ...
Click to expand...
Click to collapse
I too flashed the latest ICS Stunner and then got stuck at the bootscreen.
Dumb as it may sound, the following solution worked for me -
If you are stuck at the bootscreen and unable to enter the recovery/download mode, it is not the wrong keys you are pressing, but the wrong order in which you are pressing them.
When stuck, start by pressing the Home Key first followed by Volume Up/Down and then the Power Key.
Try twice or thrice again if it doesn't work. I realized that somehow timing is important here.
According to the latest release of Stunner, you don't need to flash the repack. But there have been some reports of users not getting a full root. Obviously they must be doing something wrong since the devs have surely tested it thoroughly.
Still, to ensure 100% success, you can start by rebooting into download mode, flash ICS LP1 repack, flash the Stunner ROM and then preferably the just released LP6 by Chainfire too. This has worked for me and several others.
Hope it helps. Don't forget to thank all the devs who built these!
ICS LP1 repack http://forum.xda-developers.com/showpost.php?p=24204609&postcount=759
I recommend you double trying as toxicthunder instructed.
I just ran through a similar problem and could boot into CWM that way.
[]s
zertyz
could be worse lads mines a fxxxing brick after flashing stunner and no waRANTEE AND HAVING TO USE MY WIFES FXXXING 3GS
So sorry to hear about you note
@denny said:
could be worse lads mines a fxxxing brick after flashing stunner and no waRANTEE AND HAVING TO USE MY WIFES FXXXING 3GS
Click to expand...
Click to collapse
SORRY sorry sorry to hear that Denny how many more bricks notes is there from using stunner do you now??? and has there been a Warning put out on the OP page ?? So sorry About Your note!!
video61 said:
SORRY sorry sorry to hear that Denny how many more bricks notes is there from using stunner do you now??? and has there been a Warning put out on the OP page ?? So sorry About Your note!!
Click to expand...
Click to collapse
there were a few but the firmware got pulled fairly quickly and warnings went out asap but alas too late for me ...the early bird dont always catch a worm
@denny said:
there were a few but the firmware got pulled fairly quickly and warnings went out asap but alas too late for me ...the early bird dont always catch a worm
Click to expand...
Click to collapse
Hi Denny is there no way to sort out the guarantee ???
video61 said:
Hi Denny is there no way to sort out the guarantee ???
Click to expand...
Click to collapse
no
Confirmed Working
zertyz said:
I recommend you double trying as toxicthunder instructed.
I just ran through a similar problem and could boot into CWM that way.
[]s
zertyz
Click to expand...
Click to collapse
Thanks for testing it out zertyz