I have a touchy USB connector. Any risk when flashing? - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Hello,
I am about to get ready to start flashing roms with my phone (Still on 2.3.5 after all this time because I didn't want to touch ISC after reports of bricking). If I understand correctly Odin basically takes care of Everything now?
My largest concern is with my USB port; Last time I messed with flashing was with the Dell Streak, which was fraught with winding flashing paths that often needed to enter a USB recovery mode that could cause Bad Things to happen if something broke. Back to my Note's USB port. It's a bit touchy and often time randomly cuts out.
So tl;dr version: Going from stock 2.3.5, is it possible to flash custom roms without touching my USB port?
Thanks in advance to any replies.
Sent from my GT-N7000 using xda app-developers app

mine too is a bit dicky, if i slightly move it, it will stop charging.
best thing to do is, Order a new one
Or... connect it, dont touch it and then attempt to flash, If it cuts out without you even touching it, I would advise not to flash at all. if it loses connection mid-flash, it can brick your phone into an unrecoverable state.
What are you attempting to flash anyway ? most things can be done on the phone itself, either through recovery or mobile odin.

Yeah that's sort of the question I was asking. Is it possible to install new roms on my phone without touching the USB port. Last time I bothered with custom roms was around two or three years ago, when things were a bit more touchy.
Sent from my GT-N7000 using xda app-developers app

Could you give me a rundown of what mobile Odin can do? If I just install that (and if I get the pro version because I likes my roots), could I install CM10 or leaked jellybean roms?
Sent from my GT-N7000 using xda app-developers app

mobile odin can be used to flash the roms that can be flashed by PC odin. TAR.<MD5.. Pro version can retain root when flashing and more over you have the choice to flash a different kernel at the same time flashing the rom.
CM10 needs to be flashed using CWM.. leaked JB roms downloaded in a tar format can also be flashed using Mobile odin

Thanks.
Can I install CWM without using my USB port?
Sent from my GT-N7000 using xda app-developers app

yes, download philz kernel and flash it via stock recovery, this will then give you root and CWM recovery which will allow you to flash anything you want.

Related

[Q] After flashing back stock ROM, the phone keeps blinking on the boot screen (HELP)

I am in desperate need of help you guys! I screwed up so hard that I don't even know where to begin...
THE SITUATION:
-Right now when I go to turn on my phone, it will only stay on the current SAMSUNG GALAXY S I9000 screen (the very first screen when booting your phone) and it keeps flashing in and out.
Before trying to use Odin to put back the original Kernal on my phone, it was just stuck as the SAMSUNG GALAXY S I9000 screen, still wouldn't start. <I followed this website step by step>
http://www.samsunggalaxysforum.com/...-to-a-stock-rom-after-installing-darky's-rom/
BEFORE ALL OF THIS EVER HAPPENED:
I finally rooted my phone and manage to download Clockworkmod recovery on my phone and then used it to flash Darky's 10.2 custom ROM. Everything turned out great except at the beginning of the boot, the screen turned all rainbow coloured, completely distorted, and it continued to do that. I then tried to go back to Recovery mode to do the Voodoo lagfix but I couldn't even get into the recovery mode anymore, it either wouldn't let me, or it did but the screen didn't go to it properly (more likely the first one). I read somewhere that if you reflash your phone again, it should make all the tweeks go away. So I tried that from the Darky's tools menu and ever since then, I've been stuck with the Boot Screen this whole time...
I already bricked my phone once, and that was before the Flashing Boot Screen.
I really need help you guys, I would at least like to have my phone back to the original basis, at least! Your help would be greatly appreciated!
THANK YOU
P.S. (i'm not that great at all this phone tweeking, but I've succeeded in doing it up until yesterday)
Can you get into download mode (vol down+home+power while putting the battery in)?
If you can, just reflash a stock or custom rom in odin (like a darky odin rom) as guided by whatever rom you choose.
If you cannot get into download mode then we should know that too.
Edit: oh it looks like you could (and hopefully still can). Try a different rom or reflash. Sometime things do go wrong but as long as you can get to the download screen you should be fine in the end.
G
gfacer said:
Can you get into download mode (vol down+home+power while putting the battery in)?
If you can, just reflash a stock or custom rom in odin (like a darky odin rom) as guided by whatever rom you choose.
If you cannot get into download mode then we should know that too.
Edit: oh it looks like you could (and hopefully still can). Try a different rom or reflash. Sometime things do go wrong but as long as you can get to the download screen you should be fine in the end.
G
Click to expand...
Click to collapse
Yes, I can get into download mode! (thank you for reading my post).
If it's not too much to ask, could you maybe find the ROM that would be good for me to flash, considering my situation?
I want to be sure that it's what the top tech guys would recommend
A link would be appreciated
thank you again!
I'd start with a Darky rom - lots of users - active forum and odin editions for your situation. I have to go but you'll find the link on the first page of the development section.
G
gfacer said:
I'd start with a Darky rom - lots of users - active forum and odin editions for your situation. I have to go but you'll find the link on the first page of the development section.
G
Click to expand...
Click to collapse
So in essence all I have to do is flash the Darky ROM V10.2 with Odin using the Download mode on my phone and it should be okay?
Wait one caveat. Was it a gingerbread rom or froyo? Use a Darky rom of the same type...
Then yes it should be ok if you follow their guide. Cross fingers.
Sent from my GT-I9000M using XDA Premium App
gfacer said:
Wait one caveat. Was it a gingerbread rom or froyo? Use a Darky rom of the same type...
Then yes it should be ok if you follow their guide. Cross fingers.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
well...I did everything you said. The ROM is on there alright, it flashed and everything (And I know this because now when the boot screen STILL FLASHES, the darkcore & darky's rom logo are on it too).
THIS TIME AROUND:
The stock recovery seems to work...
any ideas??
Well we are sort of in long shot territory now... OK first try using a different odin version or ez odin and reflash.
If still not working??
Might be warranty time then but others are welcome to chime in.
Sent from my GT-I9000M using XDA Premium App
gfacer said:
Well we are sort of in long shot territory now... OK first try using a different odin version or ez odin and reflash.
If still not working??
Might be warranty time then but others are welcome to chime in.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
Alright I'll try and reflash the same one using a different version of odin the. I'll let you know what happened
gfacer said:
Well we are sort of in long shot territory now... OK first try using a different odin version or ez odin and reflash.
If still not working??
Might be warranty time then but others are welcome to chime in.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
tried ezodin, flashed it, and i still get the exact same thing I've exhausted every single possibility there is!!!
I really need help on this, my warranty is not gonna do anything because i have the phone rooted..
If you flash a stock rom with pit the root is gone. It won't boot but they can't prove it was you either and I don't think it was you.
But see my other post on your other thread for one last thought.
G
Sent from my GT-I9000M using XDA Premium App
gfacer said:
If you flash a stock rom with pit the root is gone. It won't boot but they can't prove it was you either and I don't think it was you.
But see my other post on your other thread for one last thought.
G
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
okay that could be useful data potentially (let's hope it won't have to be).
If you didn't see my reply from the other thread, here it is:
Once I rooted my phone, I automatically went from Stock Froyo to Darky's 10.2 extreme edition. It worked and everything except for that color disfiguration and the clockworkmod recovery not working.
It's weird because after I flashed my first darky's rom, i checked the phone and it said that the firmware version was 2.3.X (I believe X may have been 4). So from what you're saying, I don't exactly think it has anything to do with the fact that I went straight from froyo stock to GB darky ROM.
So are you saying that I should flash darky's 9.3 for Froyo and THEN flash the latest version?
No I think that you need froyo re edition then stock gb with bootloader (as the instructions say I thought) then a custom gb like 10.2.
Sent from my GT-I9000M using XDA Premium App
gfacer said:
No I think that you need froyo re edition then stock gb with bootloader (as the instructions say I thought) then a custom gb like 10.2.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
Ok, so just to be 100% on this
-I should flash Darky's 9.2 froyo onto my phone,
-then I should flash regular GB onto my phone (Not sure about the bootloader part though, if you could clarify that)(Also where would I get JUST a stock GB ROM?)
-then I can flash a custom GB ROM?
gfacer said:
No I think that you need froyo re edition then stock gb with bootloader (as the instructions say I thought) then a custom gb like 10.2.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
well i can safely say that flashing the 9.2 froyo rom was a fail. It's still doing the same old routine.
I just know that this problem can be fixed somehow without sending it in to bell or samsung or something.
roma17 said:
well i can safely say that flashing the 9.2 froyo rom was a fail. It's still doing the same old routine.
I just know that this problem can be fixed somehow without sending it in to bell or samsung or something.
Click to expand...
Click to collapse
I think you are right but other than trying again and again, which I've done before -though now I know why I had too - I am out of suggestions. Good Luck and if I have a brainwave I'll let you know.
Sent from my GT-I9000M using XDA Premium App
OK a few last brainwaves:
1) Try a fully complete stock rom with cache.rfs, dbdata.rfs, factoryfs.rfs, modem.bin, param.lfs, zImage, and sbl.bin (this was from JL2 rom for Bell - not sure if they all have the sbl.bin) and pit.
The key is to make sure it is complete. Try downloading the same rom from 2 different sources just to be sure its not a corrupt download (going overboard I know).
2) Can you get into recovery? Try to format partitions (not system) under advanced features (I think - I only have 3e right now as I am trying to diagnose other issues).
3) If you have a froyo rom on at one point, try to put a steam recovery kernel on. Its not really being developed anymore but I think that if you put a CWM packaged rom on to the external SD you could flash from there or at least move it to the internal and then flash it. Worth a shot. Or you might be able to transfer one in regular CWM recovery - can't recall as I have not had to try for about 8 months.
4) If you really want to try something completely different, and I am not sure I've got the balls if it was me but if you can get a file to flash from CWM or steam that you can get on from the external SD, you might try CM7. It uses a completely different file system so you'd have to go back to froyo via odin only (as a samsung based rom will not play well when flashed on top of the cm7 file system).
And calling it a day at this one...
gfacer said:
OK a few last brainwaves:
1) Try a fully complete stock rom with cache.rfs, dbdata.rfs, factoryfs.rfs, modem.bin, param.lfs, zImage, and sbl.bin (this was from JL2 rom for Bell - not sure if they all have the sbl.bin) and pit.
The key is to make sure it is complete. Try downloading the same rom from 2 different sources just to be sure its not a corrupt download (going overboard I know).
2) Can you get into recovery? Try to format partitions (not system) under advanced features (I think - I only have 3e right now as I am trying to diagnose other issues).
3) If you have a froyo rom on at one point, try to put a steam recovery kernel on. Its not really being developed anymore but I think that if you put a CWM packaged rom on to the external SD you could flash from there or at least move it to the internal and then flash it. Worth a shot. Or you might be able to transfer one in regular CWM recovery - can't recall as I have not had to try for about 8 months.
4) If you really want to try something completely different, and I am not sure I've got the balls if it was me but if you can get a file to flash from CWM or steam that you can get on from the external SD, you might try CM7. It uses a completely different file system so you'd have to go back to froyo via odin only (as a samsung based rom will not play well when flashed on top of the cm7 file system).
And calling it a day at this one...
Click to expand...
Click to collapse
Okay, basically at this point, I just want my phone to work I've tried what you said. I remember that before rooting my phone initially I was running Froyo 2.2.1. So I found the ROM for that ( http://www.samfirmware.com/WEBPROTECT-i9000.htm ) Just like you said. I downloaded from the *Provider Samsung Galaxy S i9000 heading and picked the I9000BOJS5 ## from February 2011 because I think somewhere around there I updated my phone to Froyo. Flashed it, did everything, still no luck.
I've had a recent hunch though. When the bootscreen boots up, it keeps saying i9000 only, when before it used to say i9000M at least for a little bit (yes my phone is i9000m). Is there a stock froyo rom that's specifically designed to go with the i9000m model? Or are they just all the same?
Never give up
-Thank you so much

Wont boot but got download

Hi excuse my ignorance im a dhd user slightly different.
I rooted my wifes phone,clockwork was okay but would only boot cm7..would not allow gapps.
So i reverted to taking it back to froyo. Then i wanted ics on it,so flashed that,i kept her data so tried resoring that.
Now it just hangs at galaxy s screen
I cant enter into clockwork at all. It does enter download thankgod.
Thing is taking it back to froyo takes a while! Is there any way to take her straight to ics or cyn 7 or different rom without doing froyo.
The kernels for this phone are slighty different from mine the way they work..so how do i get the exact kernel and rom running again,
Also lol her data is on a back up i did will tgat still be there? Rom manager must save it somewhere?
ill be honest i have no idea anymore when coming to the galaxy s,im fairly confident with my dhd,but this has got me stumped
plus ill be a goner if i cant get it restored lol
Sorry for the looooong question
Sent from my Desire HD using XDA Premium App
T hink your problem is that you tried to install ICS on Froyo Base. SInce Gingerbread there is a new bootloader. If you want to install ICS or any Gingerbread-based ROM, you have to install a JVH base ROM (with bootloader), for example Ficeto_Deodexed_JVH_I9000_ODIN, first. This will update the bootloader and you may flash any newer rom via CWM.
If you have an boot-loop now, you may try flashing Ficeto_Deodexed_JVH_I9000_ODIN via ODIN, its a very basic ROM (see this thread).
Thanks for your help,its up and running again
Sent from my Desire HD using XDA Premium App
Pandur2000 said:
T hink your problem is that you tried to install ICS on Froyo Base. SInce Gingerbread there is a new bootloader. If you want to install ICS or any Gingerbread-based ROM, you have to install a JVH base ROM (with bootloader), for example Ficeto_Deodexed_JVH_I9000_ODIN, first. This will update the bootloader and you may flash any newer rom via CWM.
If you have an boot-loop now, you may try flashing Ficeto_Deodexed_JVH_I9000_ODIN via ODIN, its a very basic ROM (see this thread).
Click to expand...
Click to collapse
thats a good solution. i was facing this problem with a friends phone
Yep worked a treat,the roms on but still cant actually flash anything else,i thinks its s voodoo kernel i put on causin. The issue...but
Im leaving it now lol,its got gingerbread thats fine.
Sent from my Desire HD using XDA Premium App

[Q] [URGENT] Flashing ROM

I don't know where I started but I've ended up recovering from the dreaded:
{Phone} -/!\-{PC}
situation by loading I897UCKB1-homeBinary.tar into all slots in ODIN w/ Bootloader mode enable.
I used the volume buttons + plugging in USB to get into download mode as it was literally the only thing left.
Now I can only load DIRECTLY into the recovery menu without even putting a combo.
I JUST reflashed with Speedmod [speedmod-kernel-i897-k13c-500hz] as it was the only CWM shell I could get to work. The one in the Cyanogenmod wiki is really the drunk driver that led me here some 14 hours ago. And when I say work I mean i ca reach the recovery shell, because CWM actually was just glitching the living hell of my screen with lines of all colors and dots everywhere.
I want ANY ROM AT ALL FLASHED. The original was 2.1. All I have is CM7.zip and GoogleApps.zip in my internal memory. I can't mount my ext-sd at all, as it just gives an error. What do I do now?
Sorry for the spelling and poor in advance, it's 4AM and I haven't slept in 3 days.
I've tried LOADS and would just really like to have a relatively functional phone.
Go here and try flashing to stock. http://forum.xda-developers.com/showthread.php?t=1300843
I suggest kk4 one click with bootloader re partition
Sent from my SGH-I897 using xda premium
Thanks! I'm grabbing:
"i897uckk4 Odin One Click - Stock, CONTAINS Bootloaders, Re-partition, Full Wipe.zip"
now. Weird how that was just THERE and my sleep was nowhere to be found hiding underneath it. I'll report back asap.
The garbled boot screen you saw was due to having mismatched bootloaders. The guide specifically says you must be on gingerbread to follow the guide. So either use a non-gingerbread kernel, or upgrade to GB
Sent from my CM9 ICS i897 Captivate
Working perfectly. Took the CornKernel_UCKK4_v706 Kernel so I could customize a bit more. Rooted. And installed rom manager.
Now it is time to step up ICS
Sent from my SGH-I897 using xda premium
me too used "i897uckk4_Odin_One_Click_CONTAINS_Bootloaders_Re-partition_Full_Wipe.zip" now i want a network unlocked and stable ICS or GB ROM let me know with instructions and if i did something wrong how can i revert back to the ROM (i897uckk4_Odin_One_Click_CONTAINS_Bootloaders_Re-partition_Full_Wipe.zip) i've installed
Try serendipity VII , I flashed it earlier and I think its the best stable and fastest rom I used. Its awesome, and you can customize it so much. Link is in my sig.
Sent from my Serendipity VII flashed Captivate using xda premium

[Q] Now definitely confused

hello guys
I confirm i'm confused now and don't know how to do.
when the first ROM of ICS went out (LPY) i was so excited that i'm flashed it but i can't use the phone cause the battery can stay for one day even 5 hours.
after rezding several (concerning the brick bug) I went back to gb (following this thread http://forum.xda-developers.com/showthread.php?t=1535025&highlight=direct+dl) through mobile odin and the phone is working.
Now there is a plenty of ICS ROM LPY,LP9 etc etc.
I want know to back (to the future) to ICS but still afraid of this brick but.
Can someone tell me how is possible to move to ICS ?
One more question can we mix pda phone modem from different rom
what brick are you talking about? the only bug im aware that causes brick is the one on cf root and CWM backing up and restoring... you can safely flash isc trough odin and it will work just fine
Thank for your quick reply
Correct me if i'm wrong (very newbie on android and sgn) I just have to download one of the ics Rom (N7000XX###) and flash it without cwm and root option cause right now i have cwm and root.
Sent from my GT-N7000 using XDA
Flash from Mobile
You can use "Mobile ODIN to flash keeping Ever root and Inject Super user checked" or "use CWM to flash and select CF-root kernel" to keep root and SU intact with the new ROM.
Try any of the safe custom ROMs. PA, Asylum etc.. They are allow awesome but nothing beats PA for me. Once you use AOSP, you would never wanna go back. They are much much much better than the crappy stock GB-looking ICS.
Sent from my GT-N7000 using XDA

How to install stock Rom

My phone's usb (charging) port is not working properly.My phone is under warranty so I want to Send it to service center but problem is that I am on a custom Rom. I need to flash non rooted stock Rom .I can't use pc odin because of usb issue.
Can this be done through mobile odin or CWM.please help
Sent from my GT-N7000 using Tapatalk 2
Yes can be done through mobile ODIN. Look out for the thread of mobile ODIN pro. And this is a hardware problem purely, and I don't know if you have to even unroot and stuff like that. Just for the look, you might go to a TW based ROM for some time
Should this be made a sticky? I guess it should, a fairly common problem for our note.

Categories

Resources