Database Develop

help miui to stock

help miui to stock
Installed miui MGCv3 to try out which I liked very much but no FM radio so I Went back2 fyoro using Ezbase 2 but I get Fail on
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> cache.rfs
<ID:0/009> factoryfs.rfs
Click to expand...
Click to collapse
can get into download mode with 3 button and resistor 301k

Have you tried re-downloading all the EZbase files including the EZodin and EZpit, could be a corrupt file(maybe the pit)

I've not had a problem reverting back to the 2.2.1 EZBase firmware. I did get a lot of errors when trying to install the 2.3.3 version of EZBase though. Just make sure that you use the pit file that is in that thread and you should be good to go.
As far as the radio issue in MIUI goes, there are plenty of 3rd party fm radio apps on the market that you can use to get the radio feature back again.

Re download all the files but still no joy
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> EZbase-PDA-XWJS3.tar.md5 is valid.
<OSM> EZbase-PHONE-XXJVE.tar.md5 is valid.
<OSM> EZbase-CSC-XXJV1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> factoryfs.rfs
Click to expand...
Click to collapse

Ive had this problem. Wipe all data/factory reset from the recovery menu and then download a new firmware from www(.)samfirmware(.)com
Flash one which has 3 files, not the one which gives you one file which you enter into pda cause you cant select repartition

[Q] I kill my galaxy tab gt-p1000,need help

I receive new firmware over Samsung Kies application,and i accidently pull of cable in the middle of flashing.Now my tab is dark.It wont boot or power on.I I searched the forum and find some answers but still i did not find soluitions for my problem. Odin application see my tab on port 0:[COM9] , and i try to flash with different roms but everything i got is this :<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P1000XWJQ8_P1000XXJPZ_P1000DBTJQ1_HOME.tar.md5 is valid.
<OSM> P1000XWJQ8_P1000XXJPZ_P1000DBTJQ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
Then i wait,and wait, nothing happers for hours...
If anyone has tip what to do,I would be very grateful. Tab FCC ID :A3LGTP1000
Thanks in advance!

Try overcome Stock Save v5 method.
There is a long thread in section for Overcome 4.1 ROM.
or head to
http://www.teamovercome.net
follow their guide but you can stop after flashing the Stock Safe from Odin.
Or if you want, you can continue and end up with Overcome custom ROM which is excellent.
The guide has broken image, but follow this link and you will get the cached image copy:
http://forum.xda-developers.com/showthread.php?p=20974872

Thank you very much!!!

Make sure you enter Download Mode (volume+power buttons).
Once you do that, make sure your tab is detected in the COM port of Odin. It should be marked in yellow. Also make sure you use Odin 1.7 (this version works best for the tab!).
The behavior you describe suggests Odin cannot connect to your Tab in download mode!
If all of the above are in order, use the Overcome giude as priyana suggested, it should work fine. And be careful what you flash! Odin is not a toy...
Peace,
C.

Thanks for advice Cheatman,but i can't power on my tab. I can't get downlad mode.But when i connect tab to pc odin recognizes it some port 0:[COM9]
.Should I continue with flashing by the Overcome giude? I can certainly try my tab is dark anyway.

problem solved
"It's Alive!!!!!!!!!!!!!!!!!!!" Thank you very much!!!!! You make me happy !!!
Many thanks to priyana and cheatman!!!!
All the best!!!!

Thank you so very much !
priyana said:
Try overcome Stock Save v5 method.
There is a long thread in section for Overcome 4.1 ROM.
or head to
http://www.teamovercome.net
follow their guide but you can stop after flashing the Stock Safe from Odin.
Or if you want, you can continue and end up with Overcome custom ROM which is excellent.
The guide has broken image, but follow this link and you will get the cached image copy:
http://forum.xda-developers.com/showthread.php?p=20974872
Click to expand...
Click to collapse
Thank you so very much for the " overcome " link - I accidently soft bricked my GT-P1000 and after days of searching the web for a solution I found this post .... and I've just finished downloading and installing - and YES my TAB is alive again !!!!!!

hello,
i have a problem with my gt p1000 - i tried flashing new overcome 4 kernel with odin and heimdall and it did not work.
now the tab cant boot anymore, it only shows a mobile, an exklamation mark and a pc.
i tried flashing kernel with odin 1.85 and odin 1.7; device is being detected (yellow COM display) and all i recieve is the following message:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> zImage
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
anyone has a clue? help would be appreciated!
edit: oh well thanks i already figured it out by myself

sruf said:
hello,
i have a problem with my gt p1000 - i tried flashing new overcome 4 kernel with odin and heimdall and it did not work.
now the tab cant boot anymore, it only shows a mobile, an exklamation mark and a pc.
i tried flashing kernel with odin 1.85 and odin 1.7; device is being detected (yellow COM display) and all i recieve is the following message:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> zImage
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
anyone has a clue? help would be appreciated!
edit: oh well thanks i already figured it out by myself
Click to expand...
Click to collapse
Can you explain how you did it?
I have the same problem with less messages:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)

I am having issues with galaxy tab p1000. Currently stock on a phone PC logo. Have tried Odin 3 but it stops at all trend succeed 0 failed 1

Added!!
Odin v.3
File analysis..
SetupConnection..
All threads completed. (succeed 0 / failed 1)

[Q] Softbricked phone, only need to get data

Hi,
recently I flashed a wrong recovery file to my i9000. So now I have the phone-triangle-computer logo on the phone....
I am able to get the phone into download mode, but everytime I try to flash a CWM of TWRP tar file via Odin (both 1.83 and 3.07), both fail:
Odin 1.83:
Code:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-5.0.2.8-mini.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Odin 3.07
Code:
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010> NAND Write Start!!
This NAND Write Start doesn't complete, or show the progress indicator
I had installed CM10.1 before, and I would like to restore the data on the internal memory, potentially only via CWM, but preferably a little bit more
Anybody got an idea how to get the data or phone restored?

DaSuperGrover said:
Hi,
recently I flashed a wrong recovery file to my i9000. So now I have the phone-triangle-computer logo on the phone....
I am able to get the phone into download mode, but everytime I try to flash a CWM of TWRP tar file via Odin (both 1.83 and 3.07), both fail:
Odin 1.83:
Code:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-5.0.2.8-mini.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Odin 3.07
Code:
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> recovery.img
<ID:0/010> NAND Write Start!!
This NAND Write Start doesn't complete, or show the progress indicator
I had installed CM10.1 before, and I would like to restore the data on the internal memory, potentially only via CWM, but preferably a little bit more
Anybody got an idea how to get the data or phone restored?
Click to expand...
Click to collapse
This kernel will help you. It is flashable via Odin.

kevinrus123 said:
This kernel will help you. It is flashable via Odin.
Click to expand...
Click to collapse
Thanks! It worked!
Can't say how pleased I am, these fora are just great!

DaSuperGrover said:
Thanks! It worked!
Can't say how pleased I am, these fora are just great!
Click to expand...
Click to collapse
No problem
Thank you for hitting thanks button

Bricked Phone after trying to downgrade to 4.4.2 using odin

upgraded to 5.0 but then decide to see if I could downgrade and I bricked my phone trying to use Odin with the 4.4.2 files. Any suggestions or anyone going thru something similar?

Is it a hard brick? Can you get in recovery or download? What were your steps? With the Note 3 L update, we are able to go back to 4.4.2 and 4.4.4 via ODIN. What did you download. This info will be a big help to see if we can go back to KK from L.

Atomic Virus said:
upgraded to 5.0 but then decide to see if I could downgrade and I bricked my phone trying to use Odin with the 4.4.2 files. Any suggestions or anyone going thru something similar?
Click to expand...
Click to collapse
Try flashing this file in Odin, it does not contain the bootloader so it should flash successfully: G900A_Downgrade_to_NCE

I can get to download menu but after I run Odin 3.09 and use the recovery files AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar SYS REV.
I get the following error:
Check Fail Refer 2 > Binary 1
Secure Check Fail: system
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

muniz_ri said:
Try flashing this file in Odin, it does not contain the bootloader so it should flash successfully: G900A_Downgrade_to_NCE
Click to expand...
Click to collapse
Let me try it. Will report back.

Atomic Virus said:
Let me try it. Will report back.
Click to expand...
Click to collapse
Still getting same error.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900A_Downgrade_to_NCE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> persist.img.ext4
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Atomic Virus said:
Still getting same error.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900A_Downgrade_to_NCE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> persist.img.ext4
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Very sorry to hear that. A BestBuy Samsung Experience or AT&T shop can likely get you back up and running.

muniz_ri said:
Very sorry to hear that. A BestBuy Samsung Experience or AT&T shop can likely get you back up and running.
Click to expand...
Click to collapse
No worries. Might wait it out for a bit maybe someone will come across a similar situation.

muniz_ri said:
Very sorry to hear that. A BestBuy Samsung Experience or AT&T shop can likely get you back up and running.
Click to expand...
Click to collapse
Great news I am back up and running. I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+) from your other thread.

Atomic Virus said:
Great news I am back up and running. I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+) from your other thread.
Click to expand...
Click to collapse
OK, I see now how you bricked....the kernel for the NCE .tar you first flashed updated successfully causing the brick because your system at that point was 5.0.

muniz_ri said:
OK, I see now how you bricked....the kernel for the NCE .tar you first flashed updated successfully causing the brick because your system at that point was 5.0.
Click to expand...
Click to collapse
That is correct! Thanks for your help.

Atomic Virus said:
That is correct! Thanks for your help.
Click to expand...
Click to collapse
I did the same thing you did what exactly did you do to get it to boot back up?

Fitz110 said:
I did the same thing you did what exactly did you do to get it to boot back up?
Click to expand...
Click to collapse
I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+). Which you can get off this thread. http://forum.xda-developers.com/att-...-2015-t3021120 Sorry for the late responds.

Atomic Virus said:
I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+). Which you can get off this thread. http://forum.xda-developers.com/att-...-2015-t3021120 Sorry for the late responds.
Click to expand...
Click to collapse
Okay thanks and the link is dead do you think share the file with some way?

Fitz110 said:
Okay thanks and the link is dead do you think share the file with some way?
Click to expand...
Click to collapse
Here
http://forum.xda-developers.com/showthread.php?t=3076803

OPOfreak said:
Here
http://forum.xda-developers.com/showthread.php?t=3076803
Click to expand...
Click to collapse
Thanks but i think that's a updated version of the file presented in that post I was trying to get the original file

Fitz110 said:
Okay thanks and the link is dead do you think share the file with some way?
Click to expand...
Click to collapse
As a junior member, and it's not just you but quite a few, you really need to read and do some research on your phone before you turn it into a very expensive paperweight.
The link I provided took about 5 seconds in this very forum.
Plus doing your reading and research before asking will save you a ton of flaming. Just some friendly advice from someone that's been there done that.

Atomic Virus said:
Great news I am back up and running. I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+) from your other thread.
Click to expand...
Click to collapse
so what was the exact process? do you mind making it clear for other users? thanks.

Fitz110 said:
Thanks but i think that's a updated version of the file presented in that post I was trying to get the original file
Click to expand...
Click to collapse
No it isn't that's where you will get the Stock partitions he was talking about

OPOfreak said:
No it isn't that's where you will get the Stock partitions he was talking about
Click to expand...
Click to collapse
Okay thanks , my apologies.

HELP !!!!!!! Unrooting Samsung S6 fail

Hi everyone,
I bought a new samsung s6 and rooted it using pingpong, now i must unroot it so i can install the new update, well i downloaded the firmware stock odin 3.10, but everytime i try unrooting it usin odin i have this message
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My samsung is a G920F
firmware i trying to use is G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5
im so desesperate i tried so many time but no changing at all can someone help Me please
Thanks

Must use Odin v3.10.6
Neostatic17 said:
Hi everyone,
I bought a new samsung s6 and rooted it using pingpong, now i must unroot it so i can install the new update, well i downloaded the firmware stock odin 3.10, but everytime i try unrooting it usin odin i have this message
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My samsung is a G920F
firmware i trying to use is G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5
im so desesperate i tried so many time but no changing at all can someone help Me please
Thanks
Click to expand...
Click to collapse

wp4jot said:
Must use Odin v3.10.6
Click to expand...
Click to collapse
Hi wp4jot,
i have used odin 3.10.6 but it still don't work do you have an idea why its not working , or how can i solve this problem
Thanks

I don't. Did you flash all 4 files at once?
Neostatic17 said:
Hi wp4jot,
i have used odin 3.10.6 but it still don't work do you have an idea why its not working , or how can i solve this problem
Thanks
Click to expand...
Click to collapse

I had this problem.. You must have v3.10.6 and flash every file in the corresponding place, after that I still got a fail message but I tried un-checking the auto reboot option and that did the trick (this will make the phone stay in download mode even after you complete the flash, to quit download mode you must press the volume down button and the power button at the same time for about 10 seconds) hope that helps, let me know.

vontokkerths said:
I had this problem.. You must have v3.10.6 and flash every file in the corresponding place, after that I still got a fail message but I tried un-checking the auto reboot option and that did the trick (this will make the phone stay in download mode even after you complete the flash, to quit download mode you must press the volume down button and the power button at the same time for about 10 seconds) hope that helps, let me know.
Click to expand...
Click to collapse
I Have the same problem with S6- SMG20T (Dutch) Now trying to un-check the auto reboot otion. Hope it works for me.
didn't worked for me

wp4jot said:
I don't. Did you flash all 4 files at once?
Click to expand...
Click to collapse
What do you mean with that? witch 4 files?
Hope you can help me.
After a factory swipe and installing vodafone wallet on my S6 it says that it doesn't work on a rooted Phone

You have to put each file in the corresponding place, when you download the stock rom after you've extracted the zip you're supposed to have a file called AP, BL, CSC, AND the other which I cannot remember, those are the files you're supposed to flash, if you try to flash just AP like on the screenshot it's not going to work.

Neostatic17 said:
Hi everyone,
I bought a new samsung s6 and rooted it using pingpong, now i must unroot it so i can install the new update, well i downloaded the firmware stock odin 3.10, but everytime i try unrooting it usin odin i have this message
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My samsung is a G920F
firmware i trying to use is G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5
im so desesperate i tried so many time but no changing at all can someone help Me please
Thanks
Click to expand...
Click to collapse
I think you downloaded the wrong firmware for your phone, your phone is G920F and the firmware you are trying to flash is G925F.

@Neostatic17, it looks like you downloaded the wrong file. The file should be a tar.zip, not tar.md5. Once you download the correct tar.zip, extract the file and you will see 4 files within the one file you downloaded. Then flash all 4 files with odin.
Edit...Ok, I've checked my pc and the file is a tar.zip before you extract it and once it's extracted, there are 4 tar.md5 files. All you have to do is put the AP file in the AP slot, BL file in the BL slot and so on. I leave auto reboot checked, but that is up to you.