Phone Details:
- Xperia Z (T-Mobile) C6606
- Firmware or Build 10.1.1.B.0.166
I was able unbrick my phone and hope the method I used is helpful to others.
****Here's what happened.....******
Got the phone from T-Mobile had a lot of useless apps. Tried to root the phone all kinds of ways. Connected the phone to PC and opened up Flashtool. Flashtool did not detect the phone. I had to go into USB debugging and uncheck it off and check it back on, phone was detected and it says Root Access Allowed.
Installed Dual Recovery.. and installed the rom from zip. Rom instructions as follow:
Requirements: (Click on link below to get them)
1. Root - You probably don't really need this since this ROM itself also include stable and proper root package but most locked bootloader phones require root access to install recovery.
2. CWM/TWRP Recovery support - This is the real requirements. If you can access Recovery to flash this ROM, the rest should be working fine like root/busybox. Sadly you'll need either root or get custom kernel with recovery so you can forget root and be done with.
Instructions did not say install a different firmware, so I am thinking I can use my original firmware since the rom was based on a stock rom.
After installation of custom zip, cleared dalvik cache and reboot the phone. The phone bricked on me. All it did was cycle through the sony xperia boot screen and restart over and over again. I couldn't even get back to recovery(pressing vol. down on reboot) to restore my back up of my previous rom.
*****How I unbricked my phone*****
Remembered back in the day when I was flashing roms for on my previous xperia... I use Sony Companion Suite to restore my phone back to factory. Luckily it worked for my Xperia Z and now I am back with the stock rom.
Link for xperia Z tmobile repair.
sonymobile.com/us/software/phones/xperia-z-tmobile
Link for other phones.
sonymobile.com/us/software/phones/
Hope others find this post helpful.
I tried rooting my Sony V, but its ended up in disaster where the phone doesnt boot past sony xperia part and just loops.
I tried to root it via this link:
http://forum.xda-developers.com/showthread.php?t=2090319&page=2
Through" Gasai Yuno" step by step instructions. I have tried to originally flash my phone using the"TRIMMED-LT25i-SOL21_9.0.F.0.195.ftf or the original LT25i-SOL21_9.0.F.0.195.ftf " but it turned out a disaster.
I managed to get the bootlocker unlocked but even that seem to have re-setted everything on my phone to default and deleted everything on my phone.
SOMEONE HELP PLEASE!
All I wanted to do was load this ROM.
http://forum.xda-developers.com/showthread.php?t=2500671
Those instructions are for Android 4.0.4-based firmware. Obviously the phone will bootloop if you flash 4.0.4 over 4.1.2.
Use Flashtool to flash it to a proper 4.1.2-based firmware and get root using Binary's scripts.
You could also flash a custom root-enabled kernel using fastboot if you unlocked the bootloader.
manloonw said:
I managed to get the bootlocker unlocked but even that seem to have re-setted everything on my phone to default and deleted everything on my phone.
Click to expand...
Click to collapse
Unlocking the booloader always resets all data, it's normal.
thanks guys really appreciate the help!
Any chance you can guide me in the right direction to a 4.1.2 based firmware?
This thread has FTFs for .140. You could just search the forum for "LT25i FTF" yourself, you know.
http://forum.xda-developers.com/showthread.php?t=2227747
Ok I flashed it back to normal then I tried to install CWM Recovery through this link: http://forum.xda-developers.com/showthread.php?t=2012738
Using this method:
"Installing CWM for the first time is as simple as:
Download CWM v4 installer for ICS if you are on Ice Cream Sandwich or CWM v9 installer for JB if you are on Jelly Bean, and unzip
Enable USB debugging and connect phone to your computer
Run install.bat/install.sh"
After that I tried installing this: http://forum.xda-developers.com/showthread.php?t=2500671
But it failed and gave me error7 I think it was, so I tried to forget about the rom and tried reboot the phone back to normal but now the phone doesn't go past Sony on boot up, and I can't load up CWM.
PLEASE HELP!
Flash the .140 FTF using Flashtool once again.
manloonw said:
Ok I flashed it back to normal then I tried to install CWM Recovery through this link: http://forum.xda-developers.com/showthread.php?t=2012738
Using this method:
"Installing CWM for the first time is as simple as:
Download CWM v4 installer for ICS if you are on Ice Cream Sandwich or CWM v9 installer for JB if you are on Jelly Bean, and unzip
Enable USB debugging and connect phone to your computer
Run install.bat/install.sh"
After that I tried installing this: http://forum.xda-developers.com/showthread.php?t=2500671
But it failed and gave me error7 I think it was, so I tried to forget about the rom and tried reboot the phone back to normal but now the phone doesn't go past Sony on boot up, and I can't load up CWM.
PLEASE HELP!
Click to expand...
Click to collapse
Just for Information... Most flashable ROM zips do wipe the system partition before the actual install begins - as a result, your recovery (which is for locked bootloaders and thus stored on system partition) is also gone. Which means that on reboot neither rom nor recovery is present to be booted in.
So in the case of a broken rom zip or errors in CWM, it is important to either flash another (working) rom zip and the CWM-self-installer zip directly afterwards or restore a (hopefully) previously done nandroid backup.
Otherwise, you'll need your pc to setup your phone again ^^
Sent from my LT25i using xda app-developers app
Hi everybody,
just got an old yet effective SGS and I wanted root and get rid of touchwizz and all the crap from my carrier
I was unable to boot into DL mode, i tried everything, so I had to do it with adb reboot
I never had to use Odin to do my hacking with android so i'm not used to it but short story : I rename my rom.zip into rom rom.tar, it failed and all I have is this now :
https://www.dropbox.com/s/wk42jbmp33a3ftu/IMG_20140715_152917.jpg
Also I need to unsimlock, flashing a new rom will also do the trick right ?
thanks
What you just did is bricking your phone. It it was a zip file you need to install it from the recovery. Renaming it is not the way it works. I'm not sure if now you can fix it. Sorry, man
Sent from my GT-I9000 using XDA Premium 4 mobile app
Do you know what I can at least try?
If you can get into download mode:
Follow sections 2 and 3 in this guide.
If you can't:
Follow this guide and after that do what I sails to do if you have download mode.
Does 3-button-combo not work to get into the download mode?
(power & home & volume down)
tetakpatalked from Nexus 7 flo
so i tried the resistance thing but i was unable to find all of the part required so i bought one of these already done solution thingy
It worked, I'm now able to boot into DL mode
I also succesfully install a random 2.x rom from an unknown european carrier, no root, lots of crap installed, and simlocked
How do i get from that to my CM 11 rom ? (this time it's in .tar format via 7zip ^^')
I tried via Odin in PDA it says fail right away
what can I do ?
thanks fr all the answers guys
@Idealith simlock has nothing to do with the firmware.
You need now any root kernel for that firmware, it has to be compatible with the intiframs of your 2.x version and it will give you a custom recovery.
There you can flash first CM10.2 to get the modified partition sizes and KK ready recovery and after that you can flash CM11
IMHO, the new Mackay ICS 2014 rom based on CM9 is a lot faster than any KitKat and works better on the i9000
tetakpatalked from N7100
my question about the rom still applies cause this one is awful
but with what does it have to do then ?
EDIT : my browser didn't render the end of your answer
I'm afraid i'm not following though :/
I got my 2.3 rom to stop crashing
and I once boot into recovery mod idk how ..
I selected the 10.2 CM rom but it started rebooting over and over again
I'm really not following everything that is happening over here :/
Idealith said:
I got my 2.3 rom to stop crashing
and I once boot into recovery mod idk how ..
I selected the 10.2 CM rom but it started rebooting over and over again
I'm really not following everything that is happening over here :/
Click to expand...
Click to collapse
Hey, could you tell me which country you are at? I could then take a few steps to help you
PFFFFFFFFFFFFFFFFTTT, sent from my i9000
I am currently in France
last news : been able to reboot into CWM, I selected the mackay cm 9 based rom, it rebooted halfway thrugh only to reboot in TWRP (idk how, are both installed or is twrp in the rom too ???)
so i tried from twrp wiping everything before and it wen through, then on bot it told me it needed to factory reset, it never worker though
so now i can boot into CWM but can't access my sd card ...
thanks
Idealith said:
I am currently in France
last news : been able to reboot into CWM, I selected the mackay cm 9 based rom, it rebooted halfway thrugh only to reboot in TWRP (idk how, are both installed or is twrp in the rom too ???)
so i tried from twrp wiping everything before and it wen through, then on bot it told me it needed to factory reset, it never worker though
so now i can boot into CWM but can't access my sd card ...
thanks
Click to expand...
Click to collapse
It was perfectly normal behavior, as after flashing the zip from CM, it will in firat step upgrade your recovery to TWRP 2.2.2.0
As you have wiped already before, it would be perfectly fine to just flash the rom.zip in the new TWRP recovery, and your gapps right afterwards. The recovery upgrade is totally common on the i9000 as first step.
The i9000 can easily be unbricked by flashing a stock image with Odin.
tetakpatalked from Nexus 7 flo
tetakpatak said:
It was perfectly normal behavior, as after flashing the zip from CM, it will in firat step upgrade your recovery to TWRP 2.2.2.0
As you have wiped already before, it would be perfectly fine to just flash the rom.zip in the new TWRP recovery, and your gapps right afterwards. The recovery upgrade is totally common on the i9000 as first step.
The i9000 can easily be unbricked by flashing a stock image with Odin.
tetakpatalked from Nexus 7 flo
Click to expand...
Click to collapse
I suppose my phone has been unbricked I made a 2.3 stock rom work
What i do now :
I flash the stock rom, go back to DL mode, flash the recovery, take the battery off, boot back in recovery, wipe everything ( do I really have to wipe system and all ?), select the ROM, nd once I'm in TWRP i reselect than same ROM
for the cm9 based mackay one it keep rebooting over and over again
for CM 10.2 it says the encryption failed and I need to factory reset, then nothing works
Idealith said:
I suppose my phone has been unbricked I made a 2.3 stock rom work
What i do now :
I flash the stock rom, go back to DL mode, flash the recovery, take the battery off, boot back in recovery, wipe everything ( do I really have to wipe system and all ?), select the ROM, nd once I'm in TWRP i reselect than same ROM
for the cm9 based mackay one it keep rebooting over and over again
for CM 10.2 it says the encryption failed and I need to factory reset, then nothing works
Click to expand...
Click to collapse
Yes, that would be correct procedure. To install CM9 you will have to format data, cache and dalvik cache.
If you have never had a JVU or JVZ firmware installed, it is likely that you still have a Froyo bootloader which could be reason of the problems with Android 4.xx
tetakpatalked from N7100
tetakpatak said:
Yes, that would be correct procedure. To install CM9 you will have to format data, cache and dalvik cache.
If you have never had a JVU or JVZ firmware installed, it is likely that you still have a Froyo bootloader which could be reason of the problems with Android 4.xx
tetakpatalked from N7100
Click to expand...
Click to collapse
and how do i get that bootloader set up ?
Idealith said:
and how do i get that bootloader set up ?
Click to expand...
Click to collapse
Either by flashing a whole JVU or JVZ stock firmware, or by flashing a bootloader only.
Check my sticky thread here under the same section (help & troubleshooting), I have described whole the procedure in the OP. I have even attached the files and also video is there: http://forum.xda-developers.com/showthread.php?t=2444308
Right point would be to do it first.
tetakpatalked from N7100
tetakpatak said:
Either by flashing a whole JVU or JVZ stock firmware, or by flashing a bootloader only.
Check my sticky thread here under the same section (help & troubleshooting), I have described whole the procedure in the OP. I have even attached the files and also video is there: http://forum.xda-developers.com/showthread.php?t=2444308
Right point would be to do it first.
tetakpatalked from N7100
Click to expand...
Click to collapse
thanks you so much i have now CM 10.2 running
would you know by any chance how to un simlock it ?
Idealith said:
thanks you so much i have now CM 10.2 running
would you know by any chance how to un simlock it ?
Click to expand...
Click to collapse
Ask your carrier, I assume the phone contract isn't new anymore (or expired) so you'll get unlock code for free. Here in Europe one can obtain the unlock code after 2 years for free.
Otherwise you can ask one of the online unlock services, it costs usually around 15-20$ to get the code
tetakpatalked from N7100
Idealith said:
so i tried the resistance thing but i was unable to find all of the part required so i bought one of these already done solution thingy
It worked, I'm now able to boot into DL mode
I also succesfully install a random 2.x rom from an unknown european carrier, no root, lots of crap installed, and simlocked
How do i get from that to my CM 11 rom ? (this time it's in .tar format via 7zip ^^')
I tried via Odin in PDA it says fail right away
what can I do ?
thanks fr all the answers guys
Click to expand...
Click to collapse
I'm glad that the JIG helped you (I know I'm late )
danielbe said:
I'm glad that the JIG helped you (I know I'm late )
Click to expand...
Click to collapse
yeah that worked like a charm
it was a good idea to buy it, i would have use the resistors so much
is there a more xda way to unlock it ? my carrier wants me to send the phone and have it unlock, they won't just provide the code :/
I give up ;/ I cannot install any samsung rom above 4.3. When I do, my phone stucks on samsung logo and just refuse to turn on (its not a bootloop - it doesnt restart)
I have xxbmb4 bootloader, I have installed this rom and Hbo Kernel. What else can I do?
p.s. I can install any AOSP rom and it works just fine. And yes I do full wipe every time
No need to give up
I had the same problem yesterday.
My device was on 4.3 and I flashed Philz touch recovery and did a backup without a problem. But when i restored a backup and rebooted it was stuck at the Samsung logo. After trying so many things all day (wiping, cleaning caches, trying to root, reflashig recovery, .... ) following was worked.
flashed 4.4.4 STOCK-Official rom using Odin v3.07. then it booted SUCCESSFULLY.
http://forum.xda-developers.com/gal...ck-rom-4-4-4-gt-i9305n-i9305nxxufni4-t2886807
then rooted it using the following guide (did not use any recovery. Only rooted it using CF-Auto-Root-m3-m3zh-gti9305.tar.md5. and installed SuperSU version 2.02 provided in the post.
http://forum.xda-developers.com/gal...covery-i9305-cwm-philz-twrp-versions-t2694249
:good::good:
but then I will have new bootloader with this KNOX sh1t right ? ;/
Hi, Dear xda members
Last week i soft bricked my Sony Xperia Z c6603
After flashing modified kernel, i lost everything
I couldn't reach recovery even couldn't flash one with fastboot(as my device was not recognized)
I tried flashing offcial firmware through flashtool. It succeeded flashing
But After reboot i had bootloob and the ROM didn't boot
Finally I had a solution to get my phone fixed. Here's what i did:
*Reboot to FlashMode
*In flashtool I flashed TWRP Recovery in FlashMode
Now all custom ROMs are working but when I flash an official and other ROM's based on official, I'm having bootloops
Tried to wait. NO result
Could you help me with it?
P.S the modified kernel was made by this tool http://forum.xda-developers.com/xpe...ot-automatic-repack-stock-kernel-dm-t3301605/
When i softbricked my phone I tried to fix it according to this guide http://forum.xda-developers.com/xpe...rick-sony-xperia-z-c6602-c6603-c6606-t3215134
after i flashed the cm rom, i got the same problem. after flash the stock ROM or official firmware, It keep bootloop. how you fixed It ?
315cqab said:
after i flashed the cm rom, i got the same problem. after flash the stock ROM or official firmware, It keep bootloop. how you fixed It ?
Click to expand...
Click to collapse
Do you still need the method i have gone through?
do you know how to flash the official ROM or firmware back? now i can only flash the custom ROM
315cqab said:
do you know how to flash the official ROM or firmware back? now i can only flash the custom ROM
Click to expand...
Click to collapse
Sorry even i need this. Currently i have the same problem. I cant flash official firmware or the one that is based on official. I need the solution
Same here, after install CM 14.1, i can't go back to official or rom based in Stock...
gussbravo said:
Same here, after install CM 14.1, i can't go back to official or rom based in Stock...
Click to expand...
Click to collapse
I have several problems too including not being able to run stock anymore. (endless black screen after experia logo). I tried flashtool (latest stock via xperifirm), Sony's flashtool. Companion didn't even want to flash (UEGetPhoneInfoMissingInfo), and left me wondering wether something is corrupt.
I've been running CM's for a while now and was wondering why NFC was not working. Not sure if it needs an updated firmware or what.
Other problem I've seen is that "fastboot flash recovery" always gives an error. "fastboot flash boot" works (this is how I install TWRP).
Can I try zeroing mmcblk0 or would that brick it? (does it really need to have a TA partition to accept boot connection? How does Sony init it anyways?)
I think I have a mmcblk0 backup from after unlocking (DRM lost though) but perhaps that will give me a somewhat clean situation again. Or perhaps I can compare it.
Edit: dd-ed my old mmc backup and now Xperia Companion didn't give an error anymore, did a factory reset, and after a long wait of the blue waving animation, I got it to work.
Even NFC firmware update started after rooting and deleting /data/ucf folder.
Now I want to go back to Nougat xD