Hi,
I dropped my s3 i9305, the glass cracked and the screen turned black. I’ll need to replace the LCD Screen Touch Digitizer Assembly. On eBay there are loads of Digitizers for the i9300 but very few for the i9305. Does anyone know if both these digitizers are identical? In other words, can I use an i9300 digitizer to replace my i9305 one?
Thanks for any advice.
Hi, the lcd from an i9300 does work but it is the middle housing that is slightly different ( I have just tried this) as the motherboards are not exactly alike.
Related
I dont know how it cracked - i just put it on desk, and when i returned, it cracked.
The screen is cracked in the upper part, and it's not working at all.
Do I need just a new screen or a screen and a digitizer?
Also, LCD+Digitizer sets on eBay, are they LCDs or AMOLEDs?
I bought SAMSUNG Galaxy S i9000 LCD Digitizer Screen + Housing so all i had to save was back housing back case and mother board. Changed it alli n less then 15 minutes. cost me like 80 bucks.
Alucardi said:
I bought SAMSUNG Galaxy S i9000 LCD Digitizer Screen + Housing so all i had to save was back housing back case and mother board. Changed it alli n less then 15 minutes. cost me like 80 bucks.
Click to expand...
Click to collapse
good choise...
i was try change screen its very hard... its was hard glued bottom side and breaked...
and i bought "SAMSUNG Galaxy S i9000 LCD Digitizer Screen + Housing" like you and very easy changed.
I have a SPH-P100 tablet with a broken digitizer and LCD.
I've been looking around for a replacement and came across two sites.
This one advertises the LCD and digitizer fitting ALL carrier models.
It's basically saying there's one LCD and one digitizer for all models.
http://eyworkshops.ecrater.com/p/10276826/oem-samsung-andriod-galaxy-tab
This site has one that says P1000 model.
http://www.amazon.com/Original-Touc...Samsung/dp/tech-data/B005J2MNXQ/ref=de_a_smtd
What I'm trying to find out is if there is just one LCD and digitizer for all 7 inch tablets
OR if the P1000 will work with the P100.
Thanks for any help in advance guys.
Hello
I have an question about the galaxy S 9000/9001
I dont understand how the touchscreen works, is there no digitzer or is the digitizer integraded in the amoled screen? I repair phone,s but HTC uses a glas digitizer and samsung not.
i hope somone could tell my how it works,
sorry for my bad englisch,
Greets
Wilbert
wippie said:
Hello
I have an question about the galaxy S 9000/9001
I dont understand how the touchscreen works, is there no digitzer or is the digitizer integraded in the amoled screen? I repair phone,s but HTC uses a glas digitizer and samsung not.
i hope somone could tell my how it works,
sorry for my bad englisch,
Greets
Wilbert
Click to expand...
Click to collapse
This should have been asked in the Q&A forum.
The difference between the galaxys and note is that the note has a wacom touchscreen & pen. The galaxys only has a touchscreen and does not support pens like the note has.
Sent from my SAMSUNG-SGH-I717 using xda premium
i dont think you understand me,
I repair smartphone,s and sell them. Normally a touchscreen contains of a plate of glass (digitzer) and the lcd screen that is under the digitzer. so you look trough the digitzer at the lcd and the digitzer register what you are doing with you finger. So, the galaxy S1 en the galaxy S plus has a screen within a digitzer or somthing. On ebay you can buy glass frontplate (not a digitzer a glass frontplate) what fell over the screen, but i dont find a video how you can instal these. normally you can simply put the lcd and the digitzer out but if you do that by a s1 you scratch the screen.
From what I can see there, it is a single unit. So I would guess you could not only replace the digitizer.
As i recall they are glued together and really hard to separate,that's also why u rarely see dust and moist under the glass of the sgs
I had a broken glass and i had to change the hole unit. It is very expensive. Glass and lcd costs 170 €.
Sent from my GT-I9001 using XDA
wintel is right. The digitizer is fused/glued onto the LCD screen directly. There's no easy way to separate the two. Theoretically you can buy the two separately, but then you will have to find a way to glue the two together yourself.
the bottom half of the screen of my colleagues' ace is not responding.
To fix this, can i purchase a new glass digitizer on ebay? Or is there something else wrong?
secondly: is there a difference between just the glass front and the digitzer? Are these separate parts of the phone?
I've recently replaced the broken screen from my sisters' ace, so replacing the glass screen will not be a problem.
Hi guys
I've just bought a new white digitizer for my old Galaxy Ace that was cracked. The phone originally was black, now i bought all stuff white (home button, back cover and front glass).
I've changed everything without any kind of problems, but the digitizer won't recognize any kind of touch on it.
I've double checked the ribbon cable which seems to be perfectly connected (white mark aligned with mobo).
It's not the first time this happenz to me with the Galaxy Ace.
Old cracked digitizer still works, so it's not phone fault.
Any clue?
EDIT: The eBay seller wrote S5830 instead this digitizer was made for S5830i. So it's obv not working.
dedo.93 said:
Hi guys
I've just bought a new white digitizer for my old Galaxy Ace that was cracked. The phone originally was black, now i bought all stuff white (home button, back cover and front glass).
I've changed everything without any kind of problems, but the digitizer won't recognize any kind of touch on it.
I've double checked the ribbon cable which seems to be perfectly connected (white mark aligned with mobo).
It's not the first time this happenz to me with the Galaxy Ace.
Old cracked digitizer still works, so it's not phone fault.
Any clue?
EDIT: The eBay seller wrote S5830 instead this digitizer was made for S5830i. So it's obv not working.
Click to expand...
Click to collapse
So it was a wrong description on ebay, send it back and buy the right one