Database Develop

[Fixed] First time rooting, accidentally flashed wrong ROM what to do from this point

EDIT: Rebooted my computer and phone and it flashed fine. Thank you for all the help. I'm off to explore the world of custom roms.
Finally decided to root my phone and install CM9 from GB 2.3.6 with the LA4 Kernel. Downloaded everything I needed as per Post 3 of this thread. Accidentally flashed the newer kernel instead of the pre rooted ROM.
Realizing my mistake, I tried flashing the correct ROM and PC Odin gives me a failure. The phone won't boot, it just stays stuck on the Galaxy Note N7000 Logo with an exclamation mark at the bottom.

Check if you have cwm (power+home +volume up) If so then flash this get the standard version, then go advanced options and reboot recovery...
After that do all wipes data/cache/Dalvik cache then flash the cm9 for n7000,then flash cm9 GApps then reboot...
After the system boots to android set it up and download triangle away and use it to get rid of the yellow triangle
If you don't have cwm then download a stock GB rom and flash it via odin... Start from scratch
Cheers
Tapatalking on my GT-N7000

what is the error pc odin giving you?

Don't quite remember anymore since it was from this morning. All I recall is the little box on the top left going red.
Could I try replicating the problem or do I risk damaging my phone?

odin won't damage the phone. As above poster said check if you have cwm, else use Odin again

nokiamodeln91 said:
odin won't damage the phone. As above poster said check if you have cwm, else use Odin again
Click to expand...
Click to collapse
No, I don't have CWM so I've been downloading a stock rom since I saw that post should take an hour with glorious third world internet. In the meantime should I fish out that error message you requested or is it not worth it at this point?

If you need all data back and everything to be working I would recommend you to flash back the same ROM you had earlier using odin.
Go back to Square 1.
Then root it from Dr Ketan's post.

as you downloading the rom. you are going to use Odin again. Let know the error

Yeap, another fail while using PCOdin.
Going to install samsung USB drivers from the file in this thread and get rid of Kies.
Here's the stuff from the little window.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLA4_N7000OXALA4_N7000XXLA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> factoryfs.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/007> Added!!
Edit: Tried again after reinstalling drivers. Still no go.
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLA4_N7000OXALA4_N7000XXLA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

great

[Q] [Help] Installing a recovery to flash ROMs

Hello, I've installed the newest XXLTD Firmware and I cannot seem to make a recovery install properly on it, what should I do? which recovery should I flash?
Thanks

louayd said:
Hello, I've installed the newest XXLTD Firmware and I cannot seem to make a recovery install properly on it, what should I do? which recovery should I flash?
Thanks
Click to expand...
Click to collapse
The recovery comes with the kernel for the Note. If you want a custom recovery, flash Philz kernel. If you want KitKat then flash philz kernel and then flash the latest version of Raw Kernel.

XxPixX said:
The recovery comes with the kernel for the Note. If you want a custom recovery, flash Philz kernel. If you want KitKat then flash philz kernel and then flash the latest version of Raw Kernel.
Click to expand...
Click to collapse
Could u please link me a custom that would work with my firmware? I tries the latest philz and did not work. Thnx!

XxPixX said:
The recovery comes with the kernel for the Note. If you want a custom recovery, flash Philz kernel. If you want KitKat then flash philz kernel and then flash the latest version of Raw Kernel.
Click to expand...
Click to collapse
How shoud i install omni rom on my galaxy note gtn7000 im on Android 2.3.6 and i rooted my phone?

dmo.jr said:
How shoud i install omni rom on my galaxy note gtn7000 im on Android 2.3.6 and i rooted my phone?
Click to expand...
Click to collapse
You need to get yourself on a JB Rom first
this might help

Please can anyone help solve this? Thanks

louayd said:
Please can anyone help solve this? Thanks
Click to expand...
Click to collapse
Go SEARCH AND READ in Philz thread. Direct link to his download page is PROHIBITED. One Answer though, Find XXLTC version.

commencing atskine
Jackwu696 said:
Go SEARCH AND READ in Philz thread. Direct link to his download page is PROHIBITED. One Answer though, Find XXLTC version.
Click to expand...
Click to collapse
I did already! I couldn't find recovery matching XXLTC/LTD/LT3.. any ideas? Thanks

louayd said:
I did already! I couldn't find recovery matching XXLTC/LTD/LT3.. any ideas? Thanks
Click to expand...
Click to collapse
Use the latest XXLTA. it should work. Go to philz thread, post #3 click the link with "tw only" written beside it

Jackwu696 said:
Use the latest XXLTA. it should work. Go to philz thread, post #3 click the link with "tw only" written beside it
Click to expand...
Click to collapse
Thanks but it did not work for the new firmware should I downgrade my firmware? I wanna install slimkat

louayd said:
Thanks but it did not work for the new firmware should I downgrade my firmware? I wanna install slimkat
Click to expand...
Click to collapse
Wow? Didn't work? Oh well find philz_touch_6.19.3-n7000, flash it, reboot to recovery (press vol +, home + power button). Do all wipes n formats, flash the rom
Sent from my GT-N7000 using XDA Free mobile app

Jackwu696 said:
Wow? Didn't work? Oh well find philz_touch_6.19.3-n7000, flash it, reboot to recovery (press vol +, home + power button). Do all wipes n formats, flash the rom
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.19.3-n7000.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> recovery.img
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
:S

louayd said:
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
philz_touch_6.19.3-n7000.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:9)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
recovery.img
NAND Write Start!!
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
:S
Click to expand...
Click to collapse
Did you tick re-partition?? I was telling you to flash it through stock recovery, then reboot to recovery Not by odin. Try the XXLTA vers. In stock recovery, too. If all fails, downgrade your rom to XXLTA
Sent from my GT-N7000 using XDA Free mobile app

louayd said:
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.19.3-n7000.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> recovery.img
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
:S
Click to expand...
Click to collapse
The file you trying to flash using Odin will no be successful. Use a TW based Philz kernel.

[SOLVED FREE] URGENT Help before SERVICE [SOLVED FREE]

Hi, I tried to flash something in odin and my pc stopped usb connection, and now my phone can enter only in download mode.
When I try to flash something odin says write error. I searched on the internet and I saw that it might be an flash lock.
But I dont selected it in odin. I called samsung, and they recommended me a service. And it will be repaired for 28 USD . Can someone help me? As I helped others, now I need your help!
I will sent it to service in 3 days! Also, the repair is not free, because I dont reset binary counter....now is custom (5)

use 3 file rom file

Try wit Secure PIT file

Antox97 said:
Try wit Secure PIT file
Click to expand...
Click to collapse
amir_n71 said:
use 3 file rom file
Click to expand...
Click to collapse
Sorry but no one solution is working. I whink that I can't recover my photos from internal sdcard.
On phone appears: ,,odin transaction fail,, when I am connecting it....and on pc ,,write fail,,
What TO DO???!!!

All depends on what file the USB connection stopped.
If it was fat.bin, then it's pretty much dead.

MrMateczko said:
All depends on what file the USB connection stopped.
If it was fat.bin, then it's pretty much dead.
Click to expand...
Click to collapse
It says write error on any file. I don't know why, I never checked flash lock.
Also 1 click unbrick for samsung devices in not running on my pc.
(flash progress won't start)
-----2 days until service

Odin messages
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6500DBGMK1_S6500DXXMK1_S6500DXECML1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)

MaDaLiNoSt said:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6500DBGMK1_S6500DXXMK1_S6500DXECML1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I've NEVER seen that before It stop almost imediately Before flashing anything .. My Mini 2 stops in "Fat.Bin" .. Thats all .. did it showed any message at your phone ?? like "Secure Check Fail Id:0x95" ??

I never seen it too! I think that you must send your device into assistance, I'm really sorry

PHOTOS
Ezzam_Itachi said:
I've NEVER seen that before ... Did it showed any message at your phone ?? like "Secure Check Fail Id:0x95" ??
Click to expand...
Click to collapse
Now you can see how my phone is looking:
I see firmware error on power and recovery mode.
When I connect the usb cable in phone, I get error!
What to do??!! Next morning, tomorrow I will send it into service :crying:

Happy again
Hi, and thank you for all your feedbacks (posts). Now I recovered my phone with some pc softwares and everything is ok :victory:
Odin Log:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6500DBGMK1_S6500DXXMK1_S6500DXECML1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> fat.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> appsbl
<ID:0/003> oemsbl
<ID:0/003> partition.bin
<ID:0/003> qcsbl.mbn
<ID:0/003> qcsblhd_cfgdata.mbn
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
PC Screenshot:
Note: Next time when someone will have connecting issues with phone, is easy to post here and I will give help !
Do not create a new thread, because there are too many threads based same error. (eg. recovery ramdump or not working)

Owh, now I remember that writings.. For that I have sent my device into service :/
When your device are coming back, don't flash any firmware! If you have a NFC model, you must flash a NFC model like XXLD2!

Waw !! You made it !! :victory: okay now I need your help ... How did you do that ?? I oftenly flash my phone with odin .. Unfortunately, It never .. NEVER pass the flash ..It always failed .. Maybe with your solution I can get this done .. Thanks for your help !!

Little Flashing TUT
Ezzam_Itachi said:
How did you do that?
Click to expand...
Click to collapse
Download mini 2 firmware from SamMobile
Click to expand...
Click to collapse
Simply enter the model number of your device in the search box and a list of latest firmwares will come up. To download a firmware, you will need to be logged in to your SamMobile account using your username and password.
Click to expand...
Click to collapse
Demo Firmware list:
Disclaimer
SamMobile & me are not responsible if you brick or damage your device by using the files available on SamMobile Firmware Portal. You are doing all at your own risk! Proceed only if you are 100% sure that you know what you are doing.
Click to expand...
Click to collapse
Download and install compatible Kies from Samsung
Select Kies 2.6 for devices launched before September 2013
Click to expand...
Click to collapse
Now lastest drivers should be installed via kies application.
Download and install Odin3 from internet.
Click to expand...
Click to collapse
Now boot phone in download mode via an key combination: Volume down + home + power
If your device is not recognized, or windows failed istalling drivers (CDC or other driver)
use Zadig to force reinstall drive. Zadig can be found in heimdall unbrick pack for windows.
Click to expand...
Click to collapse
An alternative of Zadig is Microsoft Device manager. Select uninstall device from app menu, and then move usb cable to another port.
This solution might not solve your problem.
Click to expand...
Click to collapse
Good luck with flashing!
About you fat.bin error:
-Download another compatible rom
-That's it! : )

Amazing! Congratulations

Antox97 said:
Amazing! Congratulations
Click to expand...
Click to collapse
Thanks :laugh:

Thanks !!

Ezzam_Itachi said:
Thanks !!
Click to expand...
Click to collapse
No problem
Sent from my GT-S6500D using Tapatalk 2

Can anyone help me out, Recovery mode not working, Download mode working

i have once rooted my N7000 after using for few months, i returned to original Jellybean OS
"""N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar"""
But now my phone is not working ""No Recovery mode, only download mode""
tried to flash a ""TWRP CWM---PhilZ-cwm6-DDLSC-ODD-5.06.1.tar,,
&,,CF-Root-SGN_XX_OXA_LPY-v5.3-CWM5"" but both failed via ""Odin_v3.04""
now i am middle of nowhere, only samsung logo & an yellow triangle.
Tried to flash original Jellybean OS several times,
""" Custom binary count is (6):crying:
Odin Dispaly this message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> factoryfs.img
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Read almost everything, tried everything one thing came across (emmc bug ????), dont want to hard brick my phone, kindly suggest me something to do with my phone,,
plz help me

Kill all kies procesess using task manager if running in the back ground. Use main usb ports, original USB cable.. Try again to flash the Philz kernel using odin 1.85.. If that fails try a different pc. Install the samsung USB driver using this

Thanks for reply Buddy, can you plzz guide me the exact or specific philZ kernel + recovery to flash via odin 1.85...:crying:
i have already tried most of it,,, which i used earlier for rooting my phone....

erosnyx said:
Thanks for reply Buddy, can you plzz guide me the exact or specific philZ kernel + recovery to flash via odin 1.85...:crying:
i have already tried most of it,,, which i used earlier for rooting my phone....
Click to expand...
Click to collapse
Go to Philz kernel thread for n7000 and read the 3rd post.. Links are there.. Try the xxlta version..

Freezing on the splash screen logo

Hello, I have a big problem with my I9305, which had stock rom 4.4.4 XEO and root. The phone has been resetting on its own from time to time. Now the phone is dead, it freezes on the splash screen logo. Installing new room via Odin and DM doesn't work:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
In recovery menu there is message:
failed to mount /cache
Can't mount /cache/recovery/last_recovery
failed to mount /system
end so on...
Click to expand...
Click to collapse
What should I do?

Siadulinho said:
Hello, I have a big problem with my I9305, which had stock rom 4.4.4 XEO and root. The phone has been resetting on its own from time to time. Now the phone is dead, it freezes on the splash screen logo. Installing new room via Odin and DM doesn't work:
In recovery menu there is message:
What should I do?
Click to expand...
Click to collapse
Might be a corrupt nand, if that so, you will need to replace the board...sorry for bad news, maybe other member can have a different opinion.

Any options to make backup of SMS?

Siadulinho said:
Any options to make backup of SMS?
Click to expand...
Click to collapse
I don't think so, a corrupt NAND corrupts it all, i don't think you can boot anything on the phone anymore, however, a user here in XDA was able to use a memory card as a complete NAND and he even flashed a ROM and booted fine,but he was a skilled one, i don't know how he did it.
But he lost all data of course, so even if you did what he did, you won't get your SMSs.