Database Develop

EVDO Problems

I have Damagecontrol V0.9999 installed and data network works great with me but when ever i flash any other rom it stops working and says that service is unavailable. It just starts for first minute when new ROM boots up and then nothing. Not even the icon comes on top
baseband is 2.41.05.02.03
software is 2.26.605.2
Any ideas guys..

Guys please help...

I checked and found out that Version 2.1 works fine on my Phone but 2.1 Update 1 doesnt work. Which may have caused this problems. Any Suggestions..

Not sure I can help much. I'm not with sprint so I'm not real familiar with their settings. I'm Making the Assumption you are. If not let us know what carrier you are with.
Are you able to update your profile from settings >About Phone >Network >Update Profile?
Does the mobile network say connected or turning on in Settings >Wireless & Networks?
It could Be PRI related check it in Settings >About Phone >Software Information and report back with what version you have.
Get that info and note anything else the you think may be relevant ad we'll go from there.

Thanks a lot for the reply.
I am with Reliance CDMA Network in India.
There is no Update Profile setting here >About Phone >Network >Update Profile
Does the mobile network say connected or turning on in Settings >Wireless & Networks?..It says Disconnected because service is unavailable. When i reboot my Device. The 3G ICON comes for a minute or 2 and goes away.
PRI Version is 1.70 in working and 1.70_003 in not working

It also could be an issue with flashing Sprint roms. You might try the bitter sweet Rom.

Do you know if it works in the few moments that comes up. I had reset my PRI and lost my EVDO but it would not work at all, the mobile network would just say turning on all the time and the phone would get hot.
I had to compare/correct settings in the EPST menu with another HERO from my carrier. To access the menu dial ##778# I think the password for edit mode is your MSL mine was 6 zeros yours may be the same. View Mode will not show the Security section info. The settings that finally did the trick for me are below
Security Section
HDR AN Auth User ID
(LONG)
[email protected]
HDR AN Auth Password ID
xxxx
PPP User ID
[email protected]
PPP Password
xxxx
M.IP Default Profile Section
NAI
[email protected]
The HDR AN Auth User ID (LONG) may or may not start with evdo but from 2 carriers that I looked at they were similar. The small x's will be specific to you carrier. The capital Xs were my 10 digit phone number. Like I said best thing would be to do a side by side compare of yours and someone's that is working.
If all this compare and are all good I guess it is possible it could be hardware related. Good luck

But it works with Darkchoid and Damage Control V0.9999 but not other roms. Do these setting changes with ROMS

Mine did that. I put in airplane mode and back to normal and it restarted the data service and now it works

dwertz said:
Mine did that. I put in airplane mode and back to normal and it restarted the data service and now it works
Click to expand...
Click to collapse
Mine didnt worked. Any way how can I restart data service manually

Nothing works for me. All setting are same..

Guys.. plz help

What rom you running?
-------------------------------------
Sent via the XDA Tapatalk App

I tried on every ROM. Only Damagecontrol 0.99999 works and darchdroid all evrsions work..

guys plz help

Try dialling *#*#4636#*#* and go into "Phone Info". Hit the menu button then "More". There should be an option there to enable data connection. Also, did you make sure that Sprint DSA is disabled?

I am having similar issue but I have no internet at all . Just got a replacement phone today from nTelos . Got home , created goldcard and ruu to sprint . Rooted the phone and now the Evdo is not working ? I can make calls and receive and all that , however, no internet ??
I went ahead flashed Fresh Toast v2.1 and matching radio but still nothing ?? Any ideas ??

[Q] Network issue

Hello Team,
i purchased a unlocked HTC one and i use a AT&T gophone sim card. i am not able to get the LTE signals so i would like to know is the phone capable or its an issue.

Optimus5566 said:
Hello Team,
i purchased a unlocked HTC one and i use a AT&T gophone sim card. i am not able to get the LTE signals so i would like to know is the phone capable or its an issue.
Click to expand...
Click to collapse
This happened to me a few months ago. The phone is definitely capable and you will get LTE signals on the $60/month GoPhone plan.
1. First of all, call GoPhone customer support (611 from the phone) and confirm that they have your HTC One whitelisted for LTE. They're going to double check with you your phone's IMEI number (they can already see it, but will ask you for it anyway), and then confirmed that the phone is allowed to get LTE signals. They're also going to double check your APN setting and provide you with the appropriate entries for AT&T.
2. Reboot and see if you now get LTE signals. If you still don't get it, check whether your mobile network settings is set to GSM/WCDMA/LTE Auto instead of GSM/WCDMA Auto or WCDMA Preferred (or maybe something else). If you don't see any LTE option, dial *#*#4636#*#* from your dialer, and in the first drop down box choose 'GSM/WCDMA/LTE Auto' or anything with LTE just to make sure you can catch LTE signals at all. If you were able to find and switch to the setting you want, exit out, and go back to that menu, double checking if the setting sticks. If it does, reboot and try again.
3. Most people will get LTE signals after #1 above, while some were only able to get it after #2. However if you are unlucky like me, the LTE setting does not show up in mobile network and no matter what I do in the hidden menu, the setting won't stick (it's stuck on GSM/WCDMA Auto). I actually tried flashing a different radio at this point (a newer AT&T radio), but still... no LTE for me. What solved this finally for me is that I flashed a custom ROM (in my case it was ARHD 12.2). This enabled me to choose GSM/WCDMA/LTE Auto under mobile network settings, and after that I was able to get LTE. It was great! :good:
Hopefully that helps. Good luck!

[Q] HTC One (T-Mobile) "Service State: Radio Off"

Hi - I'm a semi-noob with this phone and Android in general (long-time iPhone JB'er finally saw the light), so sorry for any ignorance/stupidity in what follows...
HTC One, on T-Mobile
Android 4.3 SW# 3.24.531.3
Baseband vsn: 4A.21.3263.03_10.38m.1157.04L
Rooted, Unlocked, S-OFF
I was traveling on St Martin (French Caribbean) where T-Mobile gives free data roaming, so I turned on roaming and everything was fine - cell service, cell data, wifi all clearly working properly. After several days, I noticed no cell service or 3G indicator, but my wife's T-Mobile iPhone had full bars and 3G service. I waited a while, and (I *believe*) data & cell service came back on once for a while, but then failed again and have not returned to health since then (it's been about a week). Wifi works fine. When I tried to find a signal I would get "Error Searching for Networks". I thought maybe it had to do with roaming, but when I returned home (USA) I still had no cell signal/data.
I've tried rebooting, turning Data roaming on and off, Airplane mode on and off, all choices of Network mode, power off for a long time while charging, a couple other more obscure suggestions that I can't remember. I have not tried reverting to Stock or flashing a radio.
In poking around in settings:
IMEI: [normal] (this is different from several other people reporting similar problems)
Network Mode: GSM / WCDMA / LTE Auto
Operator: Unknown
Signal Strength: 0
Mobile network type: Unknown
Service State: Radio Off
Roaming: Not roaming
I've seen several posts here and on Android Forums with similar problems, but never quite a match - always a different phone and/or they are now missing their IMEI, which is not true for me and seems significant.
I never dropped the phone in water or anything, but I was traveling and it's possible it got more humidity than normal (one thread suggested water damage as a likely culprit).
Is there anything for me to do before (A) flashing a radio, (B) returning it to stock, (C) taking it to T-Mobile and hoping they'll fix it (still under warranty)? I haven't flashed a radio before, but it sounds like it's straightforward - if you have any suggestions, let me know.
I have an OTA update available to 4.4.2 - is it likely that would help me? And if I do that how much damage control will I have to do to get back to rooted/unlocked/S-OFF status?
Someone with a different phone said they removed their battery for a couple of hours and all was fine, but I'm scared to try to remove my battery, especially if I might have to take it for warranty repair.
Thanks for any guidance you can provide, and let me know if I should post any more info...
-lhuge

lhuge said:
HTC One, on T-Mobile
Android 4.3 SW# 3.24.531.3
Baseband vsn: 4A.21.3263.03_10.38m.1157.04L
Rooted, Unlocked, S-OFF
"Error Searching for Networks". I thought maybe it had to do with roaming, but when I returned home (USA) I still had no cell signal/data.
I've tried rebooting, turning Data roaming on and off, Airplane mode on and off, all choices of Network mode, power off for a long time while charging, a couple other more obscure suggestions that I can't remember. I have not tried reverting to Stock or flashing a radio.
In poking around in settings:
IMEI: [normal] (this is different from several other people reporting similar problems)
Network Mode: GSM / WCDMA / LTE Auto
Operator: Unknown
Signal Strength: 0
Mobile network type: Unknown
Service State: Radio Off
Roaming: Not roaming
Is there anything for me to do before (A) flashing a radio, (B) returning it to stock, (C) taking it to T-Mobile and hoping they'll fix it (still under warranty)? I haven't flashed a radio before, but it sounds like it's straightforward - if you have any suggestions, let me know.
Click to expand...
Click to collapse
Have you tried to switch on radio manually? Dial *#*#4636#*#* ---> phone info ---> there is a switch to turn on/off radio
lhuge said:
I have an OTA update available to 4.4.2 - is it likely that would help me? And if I do that how much damage control will I have to do to get back to rooted/unlocked/S-OFF status?
Click to expand...
Click to collapse
OTA update won't affect bootloader (unlocked and S-OFF). You might loose root but you can re-root after the update. Don't forget you need stock recovery to update. If you are going to send your phone for repair, you'll have to S-ON, remove tampered flag and Lock (no re-lock) the bootloader or your warranty will be invalid. You can only s-on on hboot 1.44 or 1.54 so you'll have to downgrade first.
lhuge said:
Someone with a different phone said they removed their battery for a couple of hours and all was fine, but I'm scared to try to remove my battery, especially if I might have to take it for warranty repair.
Click to expand...
Click to collapse
Do not attempt to remove the battery yourself on the M7, bad idea if you are planning to send the phone under warranty.

[SOLVED]
alray said:
Have you tried to switch on radio manually? Dial *#*#4636#*#* ---> phone info ---> there is a switch to turn on/off radio
Click to expand...
Click to collapse
Oh my freaking gawd, thank you. It actually didn't work at first - the button just read "turn off radio" (as if it was currently on), and tapping it didn't seem to cause any change. Kind of on a whim, I changed "preferred network type" from "WCDMA preferred" to "LTE Only", went out to settings to see if anything had changed, turned off WiFi, came back to the phone info page, clicked "turn radio off" again, and then I noticed that numbers on the screen were moving, and I had 4G/LTE and full bars again. I've switched back to "WCDMA preferred" and everything seems fine, but I don't know whether that's the right choice out of a long list of options - it's just what was there to start with.
I feel silly that it was so simple, but I didn't know about that testing screen. Thanks a ton.
alray said:
Do not attempt to remove the battery yourself on the M7, bad idea if you are planning to send the phone under warranty.
Click to expand...
Click to collapse
Roger that, fears confirmed. Thanks again

lhuge said:
Oh my freaking gawd, thank you. It actually didn't work at first - the button just read "turn off radio" (as if it was currently on), and tapping it didn't seem to cause any change. Kind of on a whim, I changed "preferred network type" from "WCDMA preferred" to "LTE Only", went out to settings to see if anything had changed, turned off WiFi, came back to the phone info page, clicked "turn radio off" again, and then I noticed that numbers on the screen were moving, and I had 4G/LTE and full bars again. I've switched back to "WCDMA preferred" and everything seems fine, but I don't know whether that's the right choice out of a long list of options - it's just what was there to start with.
I feel silly that it was so simple, but I didn't know about that testing screen. Thanks a ton.
Roger that, fears confirmed. Thanks again
Click to expand...
Click to collapse
better to set it to GSM/WCDMA/LTE auto.

HTC One M7 no signal after upgrade Lollipop 5.0.2
Pls help. No signal. Tried phone info-->radio-off/on, switch to gsm only, WCDMA....all - NOK

Unlocked moto x 2013 on T-Mobile lte issues

Hello everyone,
I've got a 2013 unlocked moto x that I've been using on T-Mobile. It's running the latest version, so I can't seem to root. I was wondering if there was some way with an apn or something to disable lte on the phone. I have pretty bad lte signal here and it ends up draining the heck out of my battery throughout the day. There's no setting in mobile network options at all, it just let's me switch to 2g only. Am I missing something? I've tried changing it with an app, but it doesn't stick after a reboot, which is slightly irritating.
Hope yall can help, thanks.

- use APN epc.tmobile.com instead of fast.t-mobile.com
- if that doesn't get rid of LTE then you can set to WCDMA Only mode from the Phone Info menu. This is a hidden menu, you'll need an AnyCut shortcut or an app like Radio Switcher. I have radio switcher, all it does is open the Phone Info menu. Once you get in there and toggle the option for WCDMA Only, I suggest you toggle data off then back on. I've found this helps it stick even after reboot.

Unlock the bootloader if you want root.

I'll try the other apn first thanks.
@nhizzat unless I'm mistaken I can't unlock the bootloader if I've already updated to 4.4.4

Pure Nexus 6.0 R1- Signal Works But No Data

[Q] on pure nexus 6.0 r1 I cannot get any data/lte my signal works but no data.?
I flashed the pure nexus ROM 6.0 release coming from benzorom some nightl y build not positive which. I flash the 6.0 bootloader and radio from recovery and then flashed the ROM and gapps. Can't get any data for some reason. Can someone help?

Are you on tmobile?? I had to add the correct APN to get data
Sent from my Nexus 6 using XDA Free mobile app

No I'm on Verizon actually. I always thought Verizon automatically had the APN settings stored? Its kinda odd. But it sucks because I want to use that ROM. Its so nice!

Here's your solution!
ssgtob1 said:
Hi all,
I installed the 5.1OTA and could not get Verizon Enhanced LTE (advanced calling, VoLTE, etc....) to work. I tried what everyone else suggested and nothing made it work (never showed the enhanced LTE setting in the cellular menu). Here are the steps I took in case anyone else is having the same problem.
1. Re-Install radio and bootloader from here: https://www.androidfilehost.com/?fid=95916177934540313
2. Enter the hidden menu using *#*#4636#*#*
3. Go in to Phone information
4. Click the TURN ON VOLTE PROVISIONED FLAG button (wont change)
5. Click the TURN OFF RADIO button
6. Wait a few seconds (for radio to turn off) and then click the TURN ON RADIO button.
7. Observe that the TURN ON VOLTE PROVISIONED FLAG button has changed to TURN OFF....
8. Go in to Settings>>...More>>Cellular Networks and make sure that Enhanced 4G LTE Mode is enabled.
I did all this and I still did not have data while making a call. I had to go to VZW site and go into my account and tell it to activate a device on my current line. I entered the IMEI and it gave me a warning about softcard and then went right back to same screen, When I clicked next it gave me a warning that it was unsupoorted device. After this it all worked perfect although the phone is still not recognized on the VZW site.
Click to expand...
Click to collapse
This and a quick call to Customer Care (*226) for them to provision Advanced Calling took care of it for me.

joshjackson406 said:
No I'm on Verizon actually. I always thought Verizon automatically had the APN settings stored? Its kinda odd. But it sucks because I want to use that ROM. Its so nice!
Click to expand...
Click to collapse
Go look at your apn settings/more/cellular networks/access point names/ find the one selected then compare it to what Verizon apn should be. I have tmobile and when i installed the ROM there was only two apns neither worked.
Sent from my Nexus 6 using XDA Free mobile app