Database Develop

[Q] Galaxy Tab GT 1000N won't start

Day 1
Hard reset my device. After rebooting, my tab stuck at Samsung logo and vibrating. But still can enter download mode
Day 2
The device still stuck at Samsung logo and can enter download mode. Then i tried flashing with dbdata.rfs PDA via Odin to try my luck. After reboot , the same things goes up,stuck at Samsung logo. After few minute , i tried flashing the GT-P1000_PRT_P1000XWJQ9_P1000PRTKL1_P1000XXJPZ ROM.During flashing(i don't know either it's finish already or not or either battery problem.Before flash i noticed the battery has low power about less than 10%) ,the device suddenly shutdown by it self. After the shutdown, the device goes black and try to reboot again,nothing comes up.Then i thought the battery was fully drained out, then i decide to charge up till morning.
Day 3
Trying to power up the device but nothing happen.Holding the power button about 20 sec and nothing happen but the device feel a little bit hot at the back.But when i plugged in to USB, it can detect the device and show the MTP Installation has failed.But at My computer shows 2 removable disk which comes from the device it self.After i pressed it,it say Please insert a disk to removable disk.
Can anyone please help me?Help my Old Tab.

Sounds like you have bricked your device. And I mean a real brick, not a "soft brick" as some people like to call it.
You should never try and flash your device if you have low battery as power could fail and corrupt your bootloader.
If you cant get into recovery or download mode your screwed and need to send it away for JTAG fix or board replacement.

Zelz said:
Day 1
Hard reset my device. After rebooting, my tab stuck at Samsung logo and vibrating. But still can enter download mode
Day 2
The device still stuck at Samsung logo and can enter download mode. Then i tried flashing with dbdata.rfs PDA via Odin to try my luck. After reboot , the same things goes up,stuck at Samsung logo. After few minute , i tried flashing the GT-P1000_PRT_P1000XWJQ9_P1000PRTKL1_P1000XXJPZ ROM.During flashing(i don't know either it's finish already or not or either battery problem.Before flash i noticed the battery has low power about less than 10%) ,the device suddenly shutdown by it self. After the shutdown, the device goes black and try to reboot again,nothing comes up.Then i thought the battery was fully drained out, then i decide to charge up till morning.
Day 3
Trying to power up the device but nothing happen.Holding the power button about 20 sec and nothing happen but the device feel a little bit hot at the back.But when i plugged in to USB, it can detect the device and show the MTP Installation has failed.But at My computer shows 2 removable disk which comes from the device it self.After i pressed it,it say Please insert a disk to removable disk.
Can anyone please help me?Help my Old Tab.
Click to expand...
Click to collapse
Try this:
start odin, and press power + volume down for at least 5 seconds, plug to your computer
Odin should recognize your tab. Flash again. Btw jq8, sithout the correct kernel is not for p1000n/m/l.
What u did on day 3 was ALMOST right. But you didn't press the volume down. Hence you didn't go to download mode.
P.s. if you post this in the Q&Asection, we could hv helped you earlier.

Xperia Z1 not powering on

Hi guys, I'm new with Xperia phones and also new with rooting,flashing and using recoverys..
I installed a new rom on my device (iHackers rom). When i started installing I had like 25% of battery. When I finished the installation (I didn't flash recovery again because I did that with the help of my computer before, so file - zip was not on my phone) I rebooted my phone. So here's where the problem begins. My phone wouldn't turn on. Black screen all the way. Tried the red button near the SIM card, tried power button and volume up/down, tried power button..nothing powered my phone on, but vibrations were there. The red LED is blinking when i charge the battery (idk if it's even charging). If I take the phone out of the charger, the red LED stops blinking. I can't turn my phone on or get into the recovery mode even after 20 minutes of charging on 220v.
Guys please help..I'm in panic here.

trpincek said:
Hi guys, I'm new with Xperia phones and also new with rooting,flashing and using recoverys..
I installed a new rom on my device (iHackers rom). When i started installing I had like 25% of battery. When I finished the installation (I didn't flash recovery again because I did that with the help of my computer before, so file - zip was not on my phone) I rebooted my phone. So here's where the problem begins. My phone wouldn't turn on. Black screen all the way. Tried the red button near the SIM card, tried power button and volume up/down, tried power button..nothing powered my phone on, but vibrations were there. The red LED is blinking when i charge the battery (idk if it's even charging). If I take the phone out of the charger, the red LED stops blinking. I can't turn my phone on or get into the recovery mode even after 20 minutes of charging on 220v.
Guys please help..I'm in panic here.
Click to expand...
Click to collapse
Fastboot or flashmode working or not ?

The first your mistake was to flash with 25% of battery. It's wrote everywhere to do a installation with a fully charged phone. Now probably in the middle of the installation the phone died and the installation was not completed and this mean your phone is corrupted and dead. The only advice I have now for you to left the phone under charger all night, next day with phone switched off keep push volume down and connect the phone via usb to PC, if the PC will recognize the device and it will install drivers flash a Stock FTF straight a way.

eclyptos said:
The first your mistake was to flash with 25% of battery. It's wrote everywhere to do a installation with a fully charged phone. Now probably in the middle of the installation the phone died and the installation was not completed and this mean your phone is corrupted and dead. The only advice I have now for you to left the phone under charger all night, next day with phone switched off keep push volume down and connect the phone via usb to PC, if the PC will recognize the device and it will install drivers flash a Stock FTF straight a way.
Click to expand...
Click to collapse
The installation was finished. I was in recovery after installation of the rom, when i pressed reboot button. Nothing is working at the moment..red led still blinking..

trpincek said:
The installation was finished. I was in recovery after installation of the rom, when i pressed reboot button. Nothing is working at the moment..red led still blinking..
Click to expand...
Click to collapse
Your battery is dead. Does the phone feel warm? Leave it plugged in to charge for a while (at least a few hours, maybe overnight) and it might come back.
Like the OTA warnings says, do not try to flash your phone if less than 50% battery is available. If you do, you are only asking for trouble.

xasbo said:
Your battery is dead. Does the phone feel warm? Leave it plugged in to charge for a while (at least a few hours, maybe overnight) and it might come back.
Like the OTA warnings says, do not try to flash your phone if less than 50% battery is available. If you do, you are only asking for trouble.
Click to expand...
Click to collapse
When I woke up in the morning the phone was not warm..it was hot..the whole day i was trying to bring it back to life but there were still only vibrations. When I connect it to my computer, the drivers get installed, but the power on button and combination power button+volume down don't work. The only combination that works is power button+volume up(the phone vibrates 3 times but still stays in the same condition). FlashTool doesn't recognize the phone either.

hold power+volume up. then phone vibrates 3 times and should switch off. wait a minute then try to switch it on just normal. does it slightly vibrate?
now try this again, now with charger pluged in. what happens then?

punkt said:
hold power+volume up. then phone vibrates 3 times and should switch off. wait a minute then try to switch it on just normal. does it slightly vibrate?
now try this again, now with charger pluged in. what happens then?
Click to expand...
Click to collapse
I think i have solved it..I left phone charging for 3 hours (without heating up), and then i plugged it in my computer. In PC Companion (yeah I never thought it would be that easy), i could restore my phone without even powering it on. I'm now downloading updates..But when I connected, flashtool detected that my fone is in flashmode.
:highfive:

trpincek said:
I think i have solved it..I left phone charging for 3 hours (without heating up), and then i plugged it in my computer. In PC Companion (yeah I never thought it would be that easy), i could restore my phone without even powering it on. I'm now downloading updates..But when I connected, flashtool detected that my fone is in flashmode.
:highfive:
Click to expand...
Click to collapse
Just wants to said same thing - it's probably in fastboot mode but the battery is dead, just plug it and try flashtool or fastboot.
But O.K.
One advice - guys already post that, I posted that many times as well but...
Never, never, never do that if your battery isn't fully charged.
Charge battery to 100% and restart to TWRP and check your battery percentage...
and you'll see why - it never shows correct info.
The other day I was flashing ROM and had 87% when I flashwd and boot my battery shown 36% and stayed on 36% for a few hours...that's not problem when you are in OS but when you stuck on powered off device - it could be very tricky to power it back.
That's why you can't update official ftf if you don't have more than 50% of battery power...
Sent from my C6903 using Tapatalk

Hello I'm new to xperia Z1.
I also rooted and installed ihacker rom v3.
My battery was fully charged. But after installation my phone is not starting.
In flash mode when I try to flash the stock it disconnects and reconnects. I'm not even able to install stock rom now.
---------- Post added at 12:52 PM ---------- Previous post was at 12:48 PM ----------
Ok while I was typing phone flashed the stock rom. I think this problem is with ihacker rom?

legalmantra said:
Hello I'm new to xperia Z1.
I also rooted and installed ihacker rom v3.
My battery was fully charged. But after installation my phone is not starting.
In flash mode when I try to flash the stock it disconnects and reconnects. I'm not even able to install stock rom now.
---------- Post added at 12:52 PM ---------- Previous post was at 12:48 PM ----------
Ok while I was typing phone flashed the stock rom. I think this problem is with ihacker rom?
Click to expand...
Click to collapse
No it's not.
Ihackers is working without any problems...
I said that many times but I'll repeat...
When you are flashing ROM (ftf) through flashtool, don't connect device immediately.
Open flashtool, select ftf and hit start.
Wait until flashtool say "connect device"
Then plug usb cable while holding vol down.
That way you'll prevent device to restart while it's waiting flashtool to prepare ftf...
Sent from my C6903 using Tapatalk

trpincek said:
Hi guys, I'm new with Xperia phones and also new with rooting,flashing and using recoverys..
I installed a new rom on my device (iHackers rom). When i started installing I had like 25% of battery. When I finished the installation (I didn't flash recovery again because I did that with the help of my computer before, so file - zip was not on my phone) I rebooted my phone. So here's where the problem begins. My phone wouldn't turn on. Black screen all the way. Tried the red button near the SIM card, tried power button and volume up/down, tried power button..nothing powered my phone on, but vibrations were there. The red LED is blinking when i charge the battery (idk if it's even charging). If I take the phone out of the charger, the red LED stops blinking. I can't turn my phone on or get into the recovery mode even after 20 minutes of charging on 220v.
Guys please help..I'm in panic here.
Click to expand...
Click to collapse
I have similar problem, but my battery is still over 85%, and i got this problem when i try to flash cwm recovery with fastboot... what should do?

[Q] i9001 no SGS logo, no recovery mode, won't turn on

Hi,
I was walking down the street and when I looked at my phone, the screen was black. I thought it can't be the battery since it was just charged.
I went home, plugged it to the power supply and I got the following loop:
1. Empty Battery logo
2. Black screen
3. Back to 1
So I thought I let it plugged to the power supply and try to
enter the recovery mode, but it was unaccessible
turn on my phone, but it won't even show to the SGS logo
So I plugged the phone to my computer, went to download mode and I tried 2 different stock rom with ODIN v4.43, it didn't change a thing.
Again, plugged to the computer, went to download mode and sent a RCWM 6.0.1.2 via ODIN v4.43......... it didn't change a thing.
I don't know what to do anymore... Any solutions I could try?
Regards,
Moulay.

You bricked device
Sent from my GT-I9000 using XDA Free mobile app

Moulay.e said:
Hi,
I was walking down the street and when I looked at my phone, the screen was black. I thought it can't be the battery since it was just charged.
I went home, plugged it to the power supply and I got the following loop:
1. Empty Battery logo
2. Black screen
3. Back to 1
So I thought I let it plugged to the power supply and try to
enter the recovery mode, but it was unaccessible
turn on my phone, but it won't even show to the SGS logo
...
Click to expand...
Click to collapse
I have the same problem. I've just flashed the Stock ROM after doing full wipes but my phone simply does not boot in any mode. I tried removing the battery, connecting to power, but it simply does not do anything, no boot, no logo, no battery logo... please HELP!

There are 2 possibilities:
1) For some reason, your bootloader got broken. That means hard brick.
2) I heard that there are Odin versions that work the best with every device. Odin v4.43 isn't one of them.
Sent from my GT-I9000 using XDA Premium 4 mobile app

Flashed it million time
Hi,
I flashed it using this method over and over again (7 times or so) and then, it worked for some reason. Don't know for how long though.
http://forum.xda-developers.com/showthread.php?t=1922505
Once I got in, I wipped all the data 4 times in a row and flashed it again just to be sure.
Hope it will work for you as well.

Bricked Nexus 6 (Not your typical thread)

So first things first:
I am not a noob, I have been flashing phones for years
The phone has an UNLOCKED bootloader
I know what a bootloader/recovery are etc
So last night I upgraded my phone to 6.0.1. I then decided to root it and get a kernel on for color control. So I download one of the new kernels (Elementalx) for 6.0.1 and the systemless root that he recommended in his post. I flash both files and boot the phone, the phone bootloops twice after the password to boot screen and then it works fine. I install a few things adjust a few things (nothing pertaining to root) and then before I jump into the shower I reboot it. I look at it after a few minutes and it is sitting at the google screen with the padlock, no worries it has happened before so I reboot it only to be met with this same screen. Over and over it just halts here. I do the button trick to get into the bootloader, no dice. No button combination can get me past this screen.
I then go over to my PC and try it out and see if I am getting a Q_BULK issue (I had it happen to my Galaxy Nexus before) and the PC doesn't even acknowledge it, so now I am getting a little worried. I cannot power off the device normally, it just reboots back to here. I can manage a trick with the power cable and some quick button presses to enter the "charging" mode and from there it appears to shut down. Upon boot though it comes right back to this halt. :-/
So, does anyone have ANY experience with this before I contact Motorola? I really don't want to because I have frame swapped and don't look kindly on the process of undoing it for a replacement, but if it must be then it must be. Below is a TLR
Phone boots to Google/padlock screen
CANNOT access the bootloader/recovery through normal means
PC does not recognize it (I did prior in both fastboot and recovery so the drivers are all installed)
the phone does NOT appear to be in Q_BULK
the phone will not shut down, it just boots back to here
It "was" running ElementalX and the systemless root (both are the newest) for 6.0.1
-Current status, sitting on this screen waiting to die... but it has an almost full charge

OK, first off... YOU ARE A NEWBIE.
Turn off the phone and boot to bootloader and use that to load your custom recovery and restore your working backup.
Failing that, fastboot flash the stock image from bootloader mode.
What are you hoping to accomplish by draining your battery completely, this can only make matters worse.

@scryan you are a funny man?

you didnt say anything about trying to get into recovery.. i assume you tried getting unto your recovery?

Hold power button, up and down button all at the same time. If you are on stock recovery wipe user data and cache. See if you can boot into the bootloader afterwards. That's unusual you cannot get into stock or custom (if you have it) recovery.

So you're main problem here is that you can't get into your bootloader or recovery right now? Hmm..... that can't be good. My best guess would be to keep trying to get it into your bootloader, just keep on holding volume down and power for a long time, hopefully if you can get into either bootloader or recovery you can fastboot flash a clean stock image, or restore a nandroid backup (assuming you have one) with TWRP. My best guess though.

Briefly, your device powers on, so there's sign of life. It is either your cable, pc' usb port or the usb socket of the phone is at fault. Did you try with another usb cable at another usb port in the pc ?

Let the phone power down completely. And when it dies, connect it to a charger while briefly holding the vol down button to get into the bootloader. It might take a while since the phone doesn't have any juice but this trick might just work.

If already no warranty, so dissasembly the deive, re-attack your battery

bricked?

I was trying to go back to stock after having Lineage installed but it crapped out during the install. The tablet is now stuck on the SAMSUNG logo screen and it seems impossible to do anything to get around it. The only button combo options that work are power+vol down which reboots and power+vol down +home which puts it into download mode. I've tried reloading the stock firmware and twrp using Odin but it always results in the same, the tablet reboots then goes to the standard android update screen, says it's doing an update and then reboots and it's back to the SAMSUNG screen. Nothing I do gets me into recovery and while Odin connects I can't get ADB etc to.
Any suggestions other than throw it in a drawer and forget about it?
TIA

Ok I got further. I left the tablet for the battery to die, then fully charged it, plugged into the PC and then started with the recovery key combo and bingo got the No Command screen then the standard recovery options. Deleted the cache and did a factory delete/reset and it's alive again.