Hi,
I goofed and used autorec app and without paying attention set the phone to enter fastboot mode. Now I cant get it out of fastboot mode. I tried the solution where you use the command line to erase recovery, and laf then flash the laf file. I did all that and it seemed to have gone through that without any problems. I typed in flashboot reboot and it rebooted. Then i did the next step which was holding down the power button for a long time until the phone actually shut off. But when I powered it back on and held in the down button to get into download mode... it went into Fastboot mode instead. I tried just powering off, rebooting then tapping the down button but that did not work either. Can anyone help me? Thanks in advance.
Update I found that download mode is actually the volume up button. Once I figured that out. I tried that and The download mode loading icon thing showed up but then disappeared and Fastboot came back on. I am looking to install Cryogenmod once this problem is fixed.. (if it can be fixed).
Fixed the phone. Turned out I was flashing the wrong laf file. Once I got that sorted I was able to get into Download mode.
Related
Hey guys, sorry for a new post. I did a search and wasn't totally sure about what i found so i figured i'd start a new post and get some help.
I bought a nexus off a guy for cheap but it was stuck at the fast boot (?) screen
image
the trackball doesnt work so i cant select anything. the only thing i can do is pull the battery out to shut it down. what can i do to fix this phone? I have no idea what to do to an android. I switched yesterday from wm6.5 so you're going to have to explain everything.
thank you!
You search the forums. That's what you do.
Trackball might be effed up. Replace that
That phone is unlocked
You get to that screen by holding down the trackball when you press power. (Like the above poster said)
Make sure the volume buttons or the trackball are not stuck in a pressed state.
I thought to navigate that screen you use the volume button and power button to select. Trackball doesn't work in that menu
Rellikzephyr
Sent from my Nexus One using Tapatalk
thanks for the helpful comments guys. :]
i meant to also add that none of the buttons work either, volume or power button. i tried to flash amonra's recovery thru cmd prompt but i couldnt do much after that. i couldnt get into the adb prompt. it says the device isnt found, although fastboot promt found the device fine. anyway so after i flash the amonra recovery img i can't get into recovery mode. holding the power and vol down button gets me to the hboot (i believe it is?) but again, i cant navigate the menu with any buttons to put it into recovery mode so i'm pretty much stuck here.
and just to clarify, I have done a few searches as i've said and I didnt feel sure enough that the problems mentioned were my problem so that is why I'm asking for help here.
You should not go to any forum and feel bad for posting or have to say over and over that you did a search. There are many people that can do better and some will show up, hopefully with answers that are not painful to someone who has purchased a new phone... cheap. I would flash amon ra which you can do adb without using any of the phone hardware buttons and then see where you are at. There are many posts on installing amon ra and the instructions are also in the offical thread. With any luck you just have a hosed recovery and the flash will get you rolling.
Can you not navigate the fastboot/hboot screen with the volume buttons? If not then you're gonna run into serious problems. Make sure both the volume buttons and trackball are clear. You can clean the trackball by pressing it in with a piece of cloth and pushing it in different directions while pressed in, this should clear most of the junk on it.
You can also clean the volume buttons and power button a little better by removing the battery cover. Good luck bud.
trackball+power -> fastboot mode.
volume+power -> recovery mode. if you see androids on skates you have the stock recovery.
trackball+volume+power held = reboot
Recovery, boot etc can be flashed from fastboot only.
just to clarify, the first thing that pops up when i press just the power button is the fastboot. i dont have to press anything else, just power.
i flashed amonra recovery img while i was on fastboot mode from my computer (cmd i used was fastboot flash recovery recovery-RA-nexus-v1.7.0.1.img) and it was successful.
Then i tried to put it into recovery mode w the command adb shell reboot recovery. It said that the device wasn't connected.
when i input the cmd fastboot devices i see my device connected, but when i input adb devices it says its not connected.
So i figured I'd put it into recovery mode on my phone by pressing volume+power. I get to the hboot screen with the three androids on skateboards (i realize the screen looks the same as fastboot but the selectable options here are different) but the volume buttons, trackball, power buttons don't work so i can't select "recovery" on the phone.
so this is where i'm stuck
It sounds like you have a stuck or f..d up trackball.
P_
I have the same problem has anyone figured out a solution?
Fastboot scree
GldRush98 said:
You search the forums. That's what you do.
Click to expand...
Click to collapse
Hi guys, sorry i have a nexus one i bought it and try to install and new rom. Was working at the beginning but now i am stuck with the bootloader screen. I tried everything don't know what to do. Is my phone dead and nothing else to do??
Please really need a big help there.
Can you make selections on the screen, by following the instructions on the screen?
can you help me
charnsingh_online said:
Trackball might be effed up. Replace that
Click to expand...
Click to collapse
sorry i can get some help from you to move from fastboot screen?
nsdragons said:
just to clarify, the first thing that pops up when i press just the power button is the fastboot. i dont have to press anything else, just power.
i flashed amonra recovery img while i was on fastboot mode from my computer (cmd i used was fastboot flash recovery recovery-RA-nexus-v1.7.0.1.img) and it was successful.
Then i tried to put it into recovery mode w the command adb shell reboot recovery. It said that the device wasn't connected.
when i input the cmd fastboot devices i see my device connected, but when i input adb devices it says its not connected.
So i figured I'd put it into recovery mode on my phone by pressing volume+power. I get to the hboot screen with the three androids on skateboards (i realize the screen looks the same as fastboot but the selectable options here are different) but the volume buttons, trackball, power buttons don't work so i can't select "recovery" on the phone.
so this is where i'm stuck
Click to expand...
Click to collapse
You cannot use ADB commands when you are in the bootloader (i.e., fastboot) screen. You need to be booted into the ROM or into the recovery for those commands to work.
What I find difficult to understand is how come your volume buttons work to boot into the bootloader, but don't work once you are there?
Try flashing each partition from a stock FRG33 ROM (from here). Unzip the files, and flash the boot, system and data images using fastboot (e.g., fastboot flash system system.img) and then try to reboot normally.
I just tried to access fastboot on my fire and pushed the wrong button.
When holding "Volume Up" while switching the device on, it shows "Factory APK mode..." on the screen. After releasing the button the message disappears after 2 seconds and the fire boots up normal.
Nothing has happend, it works normal and all apps still work the way they did before.
So what does that mode do?
ChrBeck said:
I just tried to access fastboot on my fire and pushed the wrong button.
When holding "Volume Up" while switching the device on, it shows "Factory APK mode..." on the screen. After releasing the button the message disappears after 2 seconds and the fire boots up normal.
Nothing has happend, it works normal and all apps still work the way they did before.
So what does that mode do?
Click to expand...
Click to collapse
Likely just safe mode, only stock apps load, when in safe mode.
Used to boot device if a non stock app is causing device to be unusable.
But why do play store and so on still work when booting into that mode?
It just displays the message while booting, but nothing changes when up and running.
5.0.0 or 5.0.1 ? mine boots on fastboot mode
5.0.1, I can take a picture of it later today, didn't know there might be a difference in the versions.
I can only get fastboot ... Are you able to do this reliably? I've tried different hold an release and timings but can get it to happen.
Sorry for the late reply.
I tried to take a photo of it displaying the mode, but my phone couldn't produce a good one, so I finally took a short video. Focus is bad but you can sometimes read it.
I can repeat the process every time: Power down, hold volume up key, power on -> factory APK mode.
Hope that helps you.
Can nobody proove this works?
I mean I can't be the only one with that mode and I'm still wondering what it does.
stays now in fastbootmode - help
Tried that, now it is showing fastbootmode, nothing else happens.
It's stuck in there, it does not react on buttons, nor is it seen by adb.
What can I do to get it back to life?
[Update]
Meanwhile I googled, installed Android SDK, went to platform-tools and tried adb and fastboot.exe.
adb devices gives an empty line.
fastboot devices gives the tablets serial and the word fastboot
fastboot in conjunktion with reboot, reboot-bootloader, continue tries but does nothing on the tablet.
Looks as if I have to wait until the batterie gives up, what do you think?
killerhippy said:
Tried that, now it is showing fastbootmode, nothing else happens.
It's stuck in there, it does not react on buttons, nor is it seen by adb.
What can I do to get it back to life?
Click to expand...
Click to collapse
hold the power button till it turns off and turn on again.
not shure but this worked on the older fires.
Success!
Thanks a lot!
My v5.0.1 german tablet boots into
- recovery mode with volume down + power on keys pressed
- fastboot mode with volume up + power on keys pressed.
Recovery mode says:
Amazon system recovery <3e>
Volume up/down to move highlight;
enter button to select.
reboot system now
apply update from ADB
wipe data/factory reset
wipe cache partition
reboot to bootloader
power down
view recovery logs
I have this same problem on my fire that I have only bootloader 5.1.1 and tablet does not start and I can not enter the recovery I wonder if I can help solve
I have 2 Fire 5th gens, 5.1.1, and both have the factory APK mode on vol up button and fastboot mode on vol down. NO recovery mode option. I can't even make it boot into recovery using fastboot reboot commands.
I really need help.
I've got my phone bricked and I can't even boot to flash mode or to recovery mode.
The last thing I've done is boot to twrp and clear data because I am going to change rom. But there is a certain error that pops up. and forgot what was it. After that, I try to flash the rom. But the same error pops up. If I remember correctly. e:ex4ts is not found? Something like that? And now. When I turn on my phone. The xperia logo still pops up. Then after that its only black screen. I tried going to recovery (power + Vol up + vol down) and also tried flash mode but nothing really happens. Its like not being detected. And when I try to charge it. The xperia logo pops up and black screen appears. The charging icon/animation is not popping up. Is there anyway to fix this? Please help. Any help would be much appreciated. Thank you.
Your phone is now bricked and won't boot into recovery.You need to flash stock rom via flashtool to recover your phone.Is that your phone's bootloader Lock?Unable to boot into recovery always happen in locked bootloader phone.
Use Flashtool to flash stock rom. But be careful to connect phone only when prompted. It should boot after that, then you can root phone again and try to install recovery again.
I have unlocked bootloader already. I think there is something wrong with the phone. I can't boot to flash mode and recovery mode. The screen continues to go black light. I've tried for more than 20 times already. But still. I can't go to flash mode. Can I go to flash mode by only connecting my phone to my pc?
http://forum.xda-developers.com/showthread.php?t=1963961
use recovery img to flash via flashtool.you'll get your recovery back
Thank you so much for answering my query. I figured it out before reading this. Yes, I forgot how to use flashtool. I forgot how to boot into flash mode. I used the method in Samsung devices (All buttons must be pressed) which technically my mistake. Thanks again.
Hi,
I was trying to install Linage OS 14 on my H9L and I got it installed fine. I then tried flashing TWRP with `fastboot flash recovery_ramdisk twrp.img` I then did `fastboot reboot` and once back into Linage I rebooted into TWRP from the power menu. After this TWRP got stuck on the loading screen so I tried rebooting, the phone rebooted back into TWRP and got stuck again. I then tried getting into fastboot by plugging in the USB and holding the volume down, rebooted into TWRP still. I then managed to get out by holding the power button and the + and - volume buttons to get into eRecovery. I then tried to do reset by doing 'Install latest version over WiFi' which downloads then fails and now I can't boot up my phone and it just goes straight to eRecovery every time I boot it up. I can still get into fastboot and I've tried flashing recovery_ramdisk, ramdisk from both a system update zip and from a TWRP backup with also no luck. At this point I really just want to get back to stock.
If anyone can help I'd really really appreciate it and be forever grateful .
Thanks,
Jake
jcbod said:
Hi,
I was trying to install Linage OS 14 on my H9L and I got it installed fine. I then tried flashing TWRP with `fastboot flash recovery_ramdisk twrp.img` I then did `fastboot reboot` and once back into Linage I rebooted into TWRP from the power menu. After this TWRP got stuck on the loading screen so I tried rebooting, the phone rebooted back into TWRP and got stuck again. I then tried getting into fastboot by plugging in the USB and holding the volume down, rebooted into TWRP still. I then managed to get out by holding the power button and the + and - volume buttons to get into eRecovery. I then tried to do reset by doing 'Install latest version over WiFi' which downloads then fails and now I can't boot up my phone and it just goes straight to eRecovery every time I boot it up. I can still get into fastboot and I've tried flashing recovery_ramdisk, ramdisk from both a system update zip and from a TWRP backup with also no luck. At this point I really just want to get back to stock.
If anyone can help I'd really really appreciate it and be forever grateful .
Thanks,
Jake
Click to expand...
Click to collapse
I also cannot flash TWRP anymore.
Power down phone, then plug a USB cable into PC then phone. Whilst plug Cale into phone press and hold volume up.
This should place you into Fastboot mode.
What does it say for FRP.
If it says that is locked that would be your issue of why you can not flash anything.
Sent from my LLD-L31 using Tapatalk
A small typo above from @hacktrix2006 , Vol Up will actually bring you to eRecovery.
Vol Down will bring you to fastboot mode.
@Sparkrite , nice catch that is what i ment. When i replied i was awake for at total of 1 minute so brain wasn't fully working right.
My device went int bootloop suddenly while I was using it. I not able to get in fastboot (when I press Power + Down it shows fastboot window for a sec and reboots again ) or recovery mode(When I press Power + Up, Screen shows up saying no command).
I was using official build(July patch). I have not enabled ADB. My bootloader is also locked.
Is it possible to get this device working?
Any help will be appreciated.
dha72 said:
My device went int bootloop suddenly while I was using it. I not able to get in fastboot (when I press Power + Down it shows fastboot window for a sec and reboots again ) or recovery mode(When I press Power + Up, Screen shows up saying no command).
I was using official build(July patch). I have not enabled ADB. My bootloader is also locked.
Is it possible to get this device working?
Any help will be appreciated.
Click to expand...
Click to collapse
search for a video tut on youtube on testpoint
dha72 said:
...or recovery mode(When I press Power + Up, Screen shows up saying no command)....
Click to expand...
Click to collapse
This is normal behavior of stock recovery: seeing "no command" hold "power" and click "Vol+", - to get to the stock recovery menu (btw, search would 100% give you this tip even in these forums).
As you are locked, and thus you have surely lost user data, you can try to make factory reset from recovery menu.
Yet I'd try to connect phone to power and make numerous attempts to reboot, occasionally rebooting into fastboot and into recovery, - with the hope that phone will switch into the other A/B slot.
If nothing helps, TestPoint/EDL is the only option except service.
But again, the problem may be hardware issue, and as you are supposed to disassemble phone preforming TestPoint, I'd check connectors inside and tried to reboot again before reflashing in MiFlash. And do not forget to reflash in fastboot after MiFlash reflash (and unlock phone - which I did immediately after purchase).