Database Develop

dead wing

is there any way to fix a wing that will not power up, wont go into bootloader mode and no lights come on when you plug it in?

Try hard reset via soft button and power button

daveoflave said:
is there any way to fix a wing that will not power up, wont go into bootloader mode and no lights come on when you plug it in?
Click to expand...
Click to collapse
can not enter bootloader...
are you sure about your operation?
turn off, unplug USB, hold camera button then plug USB.
if you can not enter bootloader, the only way is send to HTC service center.

Hikey said:
if you can not enter bootloader, the only way is send to HTC service center.
Click to expand...
Click to collapse
Not true, if there is no serious hw defect I can unbrick it with my "FrankenKaiser" unbricker tool set.
Does your PC prompt you to install drivers if you connect it via USB?

yea i dosent do anything when i plug it in

Ive got the same problem... flashing a wing from vista and it totally died. cant get into bootloader, cant get computer to recognize, cant get a peep out of the little guy.
My computer went into standby while flashing the rom, then it went into the bootloader and I tried to re-flash, then the progress bar came on the screen of the wing, then it went kaput for good!
i emailed HTC to see if they would run it over in a bus for me.

It worrrkkk!!!!
im a newbie to all this i recently bricked my wing nothing turned on no light nothing, then i was reading this post and it does work. wat i did i took out my battery put it back in then i held down the camera button and then pluged in the usb and BOOOMMMMMMMM! it went into bootloader! ahahahahahhahahah. so for all you people out there if i can do it you can too!

LG P880 hard brick can't reach internal memory

Hello,
I have an LG P880 and I had the Torch app with the flash on.
I accidentally dropped the phone and it fell with the screen down and the flash went off.
When I went so see what happened I noticed that the battery was still attached.
I tried to turn on the phone but to no avail. The power button seems to be working as I can hear it click, but the screen doesn't turn on.
Later tried to connect the phone to my PC to check if it connected in download mode, but it didn't. ADB doesn't recognize any devices either.
I don't know what else I can try.. I had some notes on the internal memory that I can't reach and I really needed them..
Does anyone know of a way to extract information from the internal memory?
The phone is still on warranty and I don't see any screws that have a void stamp. If needed I can disassemble it.
It was running CM 10.1 stable.
Thank you for your time

tyraek said:
Hello,
I have an LG P880 and I had the Torch app with the flash on.
I accidentally dropped the phone and it fell with the screen down and the flash went off.
When I went so see what happened I noticed that the battery was still attached.
I tried to turn on the phone but to no avail. The power button seems to be working as I can hear it click, but the screen doesn't turn on.
Later tried to connect the phone to my PC to check if it connected in download mode, but it didn't. ADB doesn't recognize any devices either.
I don't know what else I can try.. I had some notes on the internal memory that I can't reach and I really needed them..
Does anyone know of a way to extract information from the internal memory?
The phone is still on warranty and I don't see any screws that have a void stamp. If needed I can disassemble it.
It was running CM 10.1 stable.
Thank you for your time
Click to expand...
Click to collapse
try removing the battery, plug a usb connected to a pc, whilst holding volume down, if it goes into software download mode, you can restore it by flashing the original firmware through kdz.

zri said:
try removing the battery, plug a usb connected to a pc, whilst holding volume down, if it goes into software download mode, you can restore it by flashing the original firmware through kdz.
Click to expand...
Click to collapse
Thank you for your reply, but I have already tried that. The screen doesn't even turn on.
Another interesting thing that I found is that in complete darkness, I remove and insert the battery and try to turn it on. The lights on the touch buttons slightly blink and the phone doesn't do anything else.

tyraek said:
Thank you for your reply, but I have already tried that. The screen doesn't even turn on.
Another interesting thing that I found is that in complete darkness, I remove and insert the battery and try to turn it on. The lights on the touch buttons slightly blink and the phone doesn't do anything else.
Click to expand...
Click to collapse
If the phone does not turn on, something has probably broken inside the phone, due to you dropping it. You could try to get it repaired and hope the info will stay on it, or you could disassemble yourself and see if you can spot the problem and repair it yourself.

chasepoes said:
If the phone does not turn on, something has probably broken inside the phone, due to you dropping it. You could try to get it repaired and hope the info will stay on it, or you could disassemble yourself and see if you can spot the problem and repair it yourself.
Click to expand...
Click to collapse
Thank you for your reply, I will send it to warranty tomorrow probably. I disassembled everything except the touch screen and it seems everything is in place, since I'm don't have the knowledge for anything else and don't want to break any seals if any exist
More information: I can turn it on to the APX mode apparently (volume up + volume down + power on), however Windows says it is an "Unknown device" and doesn't even provide a vendor/device ID so no driver can be installed for the device..
Hope they can salvage my data or I'll have a hard time trying to remember my notes lol

tyraek said:
Thank you for your reply, I will send it to warranty tomorrow probably. I disassembled everything except the touch screen and it seems everything is in place, since I'm don't have the knowledge for anything else and don't want to break any seals if any exist
More information: I can turn it on to the APX mode apparently (volume up + volume down + power on), however Windows says it is an "Unknown device" and doesn't even provide a vendor/device ID so no driver can be installed for the device..
Hope they can salvage my data or I'll have a hard time trying to remember my notes lol
Click to expand...
Click to collapse
probably something inside the phone has broken as stated above, i have never heard of this APX mode and i wouldn't mess around with it, i have bricked my LG devices several times and have only fixed it with kdz

zri said:
probably something inside the phone has broken as stated above, i have never heard of this APX mode and i wouldn't mess around with it, i have bricked my LG devices several times and have only fixed it with kdz
Click to expand...
Click to collapse
The APX mode is like recovery mode but on a deeper level. You use nvflash with it. If you can't get to this mode nothing else will work more info here
I sent it to warranty, they said they will contact me within 5 days

tyraek said:
The APX mode is like recovery mode but on a deeper level. You use nvflash with it. If you can't get to this mode nothing else will work more info here
I sent it to warranty, they said they will contact me within 5 days
Click to expand...
Click to collapse
well thats some good news, goodluck with that

Emergency Mode

Hello!
What I must to do if I want turn on emergency mode (with yellow background) on this phone? Thanks for help!

I havn't seen any modes with the yellow background on my phone when I had the stock firmware, the only ones I've seen are the ones dexter found
http://forum.xda-developers.com/showthread.php?t=1741892
I believe the lg pc suite can help restore the phone or was it lg mobile support tool, but it will probably download the firmware from lg and I don't know if you'll be able to root or bootloader unlock this phone with a newer firmware than v20a
you can also restore the firmware if you have the KDZ file using this tutorial
http://forum.xda-developers.com/showthread.php?t=2069723
I hope that helps

Problem is very big. Phone can't rurn on, screen is black, buttons under screen aren not working, hard reset not wotking, PC can't find device...

Poland_Developers said:
Problem is very big. Phone can't rurn on, screen is black, buttons under screen aren not working, hard reset not wotking, PC can't find device...
Click to expand...
Click to collapse
Could you tell us what caused the problem? That might help to pin it down.
In the mean time see if you can enter S/W Upgrade mode. Hold the volume down button and plug in a USB cable.
Sent from my LG-P880 using XDA Free mobile app

Every button not working, screen is black...

Help people to help you
Poland_Developers said:
Every button not working, screen is black...
Click to expand...
Click to collapse
Excuse me for pointing it out, but you are being too concise in your descriptions.
Is the phone even working?
Since you have no buttons, no screen, no PC connection, in lack of more details I tend to believe that it could be turned off and unable to be switched on.
Have you ever had problems with power button?
Have you checked your battery?
It could have been fully discharged, have you tried recharging it for some time?
Does the phone reacts when plugged to a recharger?
See? in a single post I put mor questions than all your statements you put in three of your posts.
You are not helping people to help you.

[Q]Phone is dead or ...? need help to decide.

A friend brought me the phone. When charging from the adapter to the phone logo LG. The buttons do not respond. When I connect the phone to the PC, it does not see it 3 times on 3 reboots and gives the msg "After removing and reattaching battery, press power key to reboot and keep using phone". These manipulations do not give any result. If you pull out the battery and connect the phone to any key (VOL-) button to a PC the starts vibrating motor at different speeds.
Question. Phone died or bootloader or something else, there are options to do something at the home or just service center.
THX

flash rom again with lg support tools

pc and this tool do't see the phone...

rentgen said:
pc and this tool do't see the phone...
Click to expand...
Click to collapse
make sure you pflash correct step by step

rentgen said:
pc and this tool do't see the phone...
Click to expand...
Click to collapse
You have to plug it powered off with volume - button pressed. If it is still unrecognized than try another computer, helps for me.

i tried 3 pc. phone only vibrates with different speed. ((

any ideas???

give us some details ...what rom you use kernel etc

Try to flash kdz via that tutorial:
http://forum.xda-developers.com/showthread.php?t=2069723
Important: You will wipe all data.
Note: If you can't get sw upgrade screen, you just geting some green stripes or similar try without removing battery,that was in my case, just left battery inside phone trough all process.

greece-for-ever said:
give us some details ...what rom you use kernel etc
Click to expand...
Click to collapse
stock

rentgen said:
When I connect the phone to the PC, it does not see it 3 times on 3 reboots and gives the msg "After removing and reattaching battery, press power key to reboot and keep using phone"
THX
Click to expand...
Click to collapse
My 5 cents are on that your volume - button is stuck (or the phone thinks it is) being held, hence you enter "lg service mode" when you plug it into computer.It would also explain the reboots with vibrations.
Make sure that it isn't the case, other than that I think you should take it to a service center

thx 4 answears.
I recorded the video that you could see what happens
http://youtu.be/GYic7b6dwS0
ps
I disassembled the phone no button is pressed

rentgen said:
thx 4 answears.
I recorded the video that you could see what happens
http://youtu.be/GYic7b6dwS0
ps
I disassembled the phone no button is pressed
Click to expand...
Click to collapse
Don't you have to remove the battery, hold the power button, then plug in the USB cable while still holding it (release after S/W comes up) in order to make the phone boot into S/W mode? In the video you just plug the USB in and put battery back in a bit after.
I suggest you try different methods of booting into S/W and also try different flashing methods to re-flash the stock firmware.Should these fail, you should get it to a LG service center.
Also is that a crack on your micro sd reader or is it just a scratch at http://www.youtube.com/watch?v=GYic7b6dwS0#t=10 ?
Did your phone receive any damage physically? Can you tell me what exactly happened to it?

ottomanhero said:
Also is that a crack on your micro sd reader or is it just a scratch at http://www.youtube.com/watch?v=GYic7b6dwS0#t=10 ?
Did your phone receive any damage physically? Can you tell me what exactly happened to it?
Click to expand...
Click to collapse
I contacted the owner. and you were right !!! I will write a detailed answer and record the video later today.

Yes another bricked VS980, anyone help

Ok long story
I bricked my device (totally dead, no power no dl mode no led not nothing at all), i know what i did wrong, then after plenty of research I ended up tripping the area in motherboard to bring phone back to life and I was successful. I brought it back to life started over completely with a stock device like new, I rooted and loaded up some roms and all was ok. Then....
Someone I knew needed a new device but did not want it rooted as they knew nothing about root and wanted a stock device, so I TOT all the way back to stock and told them the device would run through all the updates up to Lollipop and it did, BUT the OTA to lollipop bricked the device
Yes with the phone stock and doing regular updates it bricked, they brought it to me and I was able to trip the capacitors again and was able to get into bulk mode and AGAIN was able to bring device back to life, so I sat there and one by one let the updates come in on a COMPLETELY STOCK DEVICE and ONCE AGAIN the freakin OTA bricked the device, so.....
I have not been able to get it back, I went through the same steps to get device back, and I have now done everything possible (I think) and cannot get it back.
I have tripped the IC capacitors and gotten the 9006 and 9008, when I get the 9006 and all the partitions pop up, I use the SRK tool and it works, but then when I go to reboot I used to get the LG logo bootloop and was able to turn off and go into download mode, but now download mode freezes on the little icon and download mode never opens up, so in turn I cant TOT or KDZ back to stock. I have tried the boarddiag, I have even tried the Ubuntu fix and nothing, my symptoms so far:
download mode frozen with the little icon but download mode does not show up, I sometimes get just a vibration on/off that never ends, I have also gotten a red LED & LG logo boot loop. I have literally lost 2 days trying to figure this out. My question is, is there anyone that will do this for me. I will pay to ship and return, Please anyone.

stay-down said:
Ok long story
I bricked my device (totally dead, no power no dl mode no led not nothing at all), i know what i did wrong, then after plenty of research I ended up tripping the area in motherboard to bring phone back to life and I was successful. I brought it back to life started over completely with a stock device like new, I rooted and loaded up some roms and all was ok. Then....
Click to expand...
Click to collapse
Hi,
Have you tried this ? -->http://forum.xda-developers.com/showthread.php?t=2582142
LMK if it helped you.

iubjaved said:
Hi,
Have you tried this ? -->http://forum.xda-developers.com/showthread.php?t=2582142
LMK if it helped you.
Click to expand...
Click to collapse
Yes I tried that and Ubuntu would never see my device. Upon entering the first command I would not get a return command identifying my device.

Can you do one more thing? Disassemble your battery, reassemble it , plug it in wall charger , charge it for some time and go to download mode, see if its working?

iubjaved said:
Can you do one more thing? Disassemble your battery, reassemble it , plug it in wall charger , charge it for some time and go to download mode, see if its working?
Click to expand...
Click to collapse
charged up.
This is where I am right now.....If I turn on the device i get LG screen then it turns off and LED flashes red one time, then it loops doing the same thing.
If I hold vol up and plug in it will show download mode about to start but then powers off and red LED and it boot loops again.
I noticed if I power off and hold power button, then it will vibrate on and off while im holding power button, weird.
If I open up device to trip ic in motherboard, the device does the weird vibration while plugged in as i am attempting to trip mb.
I can trip it though and get 9006 or 9008 with all the partitions popping up and i have used every single program on here to unbrick but after all those programs all i get is the damn LG screen and red LED boot loop. I am totally giving up.

.....

Then i have no idea what could fix your phone. I recommend you bring it to a repair shop.

iubjaved said:
Then i have no idea what could fix your phone. I recommend you bring it to a repair shop.
Click to expand...
Click to collapse
Yeeah I think I will just let it go, it gave me a good run and I will just hang on to it just to have another device in the drawer.
Thanks for the help

stay-down said:
Yeeah I think I will just let it go, it gave me a good run and I will just hang on to it just to have another device in the drawer.
Thanks for the help
Click to expand...
Click to collapse
Even though i had to replace my LCD recently, im still using this device as my daily driver though!
Np.