Please can someone tell me how to flash KK over my Galaxy Note GT-N7000, Im running 4.0.4, Philz Touch 3 6.0.2.3. kernel 3.0.15 LRK.
I have read mutable methods over the last 3wk about Custom Rom installations, but they all assume your coming from JB , then when I go and get the files it turns out they no longer exist.. however I found one C.R and I manage to get all the files,I hope..
I am ROOTED
raw_kernel_r5_tw
omni-4.4.4-20150217-n7000-NIGHTLY
pa_gapps-modular-nano-4.4.4-20150308-signed
UPDATE-SuperSU-v1.80
Can someone confirm this is the order of Flashing
If not can you nudge me in the right direction please...................:angel:
So what is the problem,there was a time here you could ask a question and would get some sort of reply Is it that difficult to flash my phone now, just say yes or no?? someone please, very grateful
The order looks quite good. Flash raw and reboot back to recovery again. Do all the wipes and flash rom and gapps. Reboot system. Boot first up and setup your device. Last flash su...
Related
Would appreciate if someone could help me with my problem - I had earlier used CF-Root to root and install recovery which went off well, took a nandroid backup and then tried to flash CM9 through recovery. WIthin a few seconds it rebooted, showed the Cyanogenmod splash screen and went back into recovery - only this time it was a newer recovery (6.0.0.2) than what CF-Root had installed. I'm not able to install through zip file and for some reason I am not able to restore from nandroid as it says the md5 does not match. So as of now I am stuck in recovery.
To add to this, I realize that I messed up as the instructions said to update to a GB rom if coming from Froyo, which I did not notice. Any idea what I can do from here? If I can still run through this process can someone point me in the direction of a suitable GB ROM I can install? My end goal is to be on CM9, but right now would just be happy to get back to the stock GB ROM as well.
Flash to the stock firmware again? at SamMobile? That is what I did when my device did not boot up after installing CWM recovery and some rom.
skiddyrow said:
Would appreciate if someone could help me with my problem - I had earlier used CF-Root to root and install recovery which went off well, took a nandroid backup and then tried to flash CM9 through recovery. WIthin a few seconds it rebooted, showed the Cyanogenmod splash screen and went back into recovery - only this time it was a newer recovery (6.0.0.2) than what CF-Root had installed. I'm not able to install through zip file and for some reason I am not able to restore from nandroid as it says the md5 does not match. So as of now I am stuck in recovery.
To add to this, I realize that I messed up as the instructions said to update to a GB rom if coming from Froyo, which I did not notice. Any idea what I can do from here? If I can still run through this process can someone point me in the direction of a suitable GB ROM I can install? My end goal is to be on CM9, but right now would just be happy to get back to the stock GB ROM as well.
Click to expand...
Click to collapse
you better use the overcome stock gingerbread safe 5 (the best stock for all situations) google overcome.com and get the files, you will find also a tutorial for how to stock your tab before updating it to overcome or cm9 etc...
If I helped you, please press the thanks button
MarlX said:
Flash to the stock firmware again? at SamMobile? That is what I did when my device did not boot up after installing CWM recovery and some rom.
Click to expand...
Click to collapse
so the reflash from scratch works for you
If I helped you, please press the thanks button
Thanks sos_sifou - worked great! I think I'll stick with the Overcome GB ROM for a while as it works pretty good, and look at CM9 / 10 whenever it gets stable!
Hey pros …
I just flash cm10 rom and stuck on cm10 boot screen.
1. Flash abyss kernel 4.2
2. Flash cm10 rom and JB GAPP
3. Reboot and stuck on boot screen
4. Try to get into CWM by using button combo but it won't get me into CWM and it straight go to boot screen
I SERIOUSLY NEED HELP !!!!!!!
Can anyone help me Galaxy note is the best phone I ever had I don't want to lose it pls help me pls ……
Normally you can fix this by doing a wipe/factory reset in CWM but since you cannot enter CWM i dont know.
If u really cannot get into CWM maybe its best to start over.
Flash the CM9 kernel with odin and try to enter CWM after that and flash CM10+gapps again. (dont forget to do the wipe/factory reset)
It should boot without probs.
mengzaii said:
Hey pros …
I just flash cm10 rom and stuck on cm10 boot screen.
1. Flash abyss kernel 4.2
2. Flash cm10 rom and JB GAPP
3. Reboot and stuck on boot screen
4. Try to get into CWM by using button combo but it won't get me into CWM and it straight go to boot screen
I SERIOUSLY NEED HELP !!!!!!!
Can anyone help me Galaxy note is the best phone I ever had I don't want to lose it pls help me pls ……
Click to expand...
Click to collapse
You flashed a bleeding edge rom without even reading the 1st Page containing the instructions. What's the point of doing instructions if they aren't used. Go back and read and preferably stay on stock until you understand what you are doing
Sent from my GT-N7000 using xda app-developers app
You need to flash cm based roms from cm base which is best to flash from gb rom. Which version were you trying to install?
If you can get into download mode, flash a root able gb rom and root, add cwm, then flash cm10
Sent from my GT-N7000 using xda premium
I had exactly the same problem earlier tonight... CM10 completely nuked my phone, couldn't boot into recovery or anything...
working on getting it back now using a stock GB Rom and Odin (PC) as i could still access download mode... hopefully can recover that way, fingers crossed...
not sure what the problem is, but i'm staying away from CM10 previews until all the bugs are sorted out now...
M
That's why when you are a noob and have never flashed any custom rom on your device, the best way to avoid a brick and to come here later looking for help when your phone is bricked is to read the ENTIRE thread even if it is 50 pages long! There will also be people who have bricked their phone on the rom's main thread and you will learn a lot by reading everything!
Final5k said:
That's why when you are a noob and have never flashed any custom rom on your device, the best way to avoid a brick and to come here later looking for help when your phone is bricked is to read the ENTIRE thread even if it is 50 pages long! There will also be people who have bricked their phone on the rom's main thread and you will learn a lot by reading everything!
Click to expand...
Click to collapse
well... That's total Bulls**t
I no expert nor noob, I was.
but reading 50 pages ? total crap
I never do that, there is google, you can almost always find a short answer.
as far as I know, he didn't do anything wrong. I did the same, it work, he did it, it didn't work. guess what, the 50 pages didn't help at all.
the 50 pages can help as last option. or not.
Flashing CM ROM must come from untampered CM nightly not TW-based ROM
1- Use PC Odin to flash stock firmware - preferably Gingerbread (we all know ICS issues)
2- Reboot the phone, let the ROM start & check if u still have root
3- If not : Re-root your phone, Please check Drketan threads for rooting directions
4- When rooted : Reboot into recovery
5- Do full wipe (data - cache - dalvik) 3 times in a row
6- Do System format - go to advanced & choose Format /system
7- Now flash a stable CM base.. I prefer using the latest CM10 nightly (not CM-based ROM)
8- Now without rebooting, flash your preferred CM-based ROM.. I use PA by Utacka
9- Flash Gapps (if your ROM doesn't have them included.. plz read original post (OP) of the corresponding ROM)
10- Re-clean Cache & Dalvick .. only once
11- Reboot & Enjoy
I totally agree with Final5K.. I still read the instructions carefully, I even read some threads backwards to know the issues with the build and perhaps the fixes.. Unless, you would like to superbrick your phone.. that's up to you
CM roms are cmpletely ok. usually the op says to do factory reset after flashing rom before booting or it will get stuck on logo.
Hello all... After reading here and there and in other forums, I have a series of questions that I would really appreciate if anyone can answer based on facts...
I currently have a Galaxy Note N7000 with this settings:
Android Version: 4.0.3
Baseband Version: N7000XXLPT
Kernel Version:
3.0.15-n7000XXLPY-CL474507
[email protected] #3
SMP PREEMPT Fri May 4 04:49:06 KST 2012
Build Number: IML74K.XXLPY
I want to install the 4.1.2 leaked version (already downloaded it) BUT I have some questions:
1.- I have read in different sites that I just need to do it with ODIN, no wipe required; and in other sites I have read that after installing, a wipe is required. Which one is it?
2.- According to many sites, by wiping I am at risk of hard bricking my note because of the death bug found in ics kernels. Should I still wipe?
3.- If after testing 4.1.2 I decide to roll back to I.C.S.... Again I should do that via Odin... but again I should wipe right? At risk again of bricking?
4.- This leaked version DOES NOT accept the s-pen functions at all right? so basically my spen would just be useless...
5.- THe recovery that is installed in the phone is the basic recovery that came with the phone, I havent changed it... I have read that installing some recovery files is dangerous. Which recovery is recommended?
6.- My note is NOT rooted... Does this affect my possibility of updating with this leaked firmware?
7.- and final... Do you guys recommend that I update or should I wait for the official firmware?
Sorry for the long post, but I need advice from the best ...
Greetings from Venezuela
1. you can install that without wipes using PC odin. but its a matter of luck. if it gets stuck in a boot look then you will need to do a factory reset and for that to be safe you need to install a safe kernel Philz XXLSA (i guess thats what you downloaded)
get it from here
http://forum.xda-developers.com/showthread.php?t=1901191
can be flashed using stock recovery and external SD
2. No, Always install a safe kernel and perform wipe
3. You may have to wipe this time for a proper boot as it might enter a boot loop. Same procedure, install Philz and do a factory reset. Its better to do a nandroid backup of ICS rom if you wish to return back to ICS. this way all your settings apps and customizations will be restored.
4. Incorrect. Spen is fully functional on JB leaks TW based.
5. Philz works perfectly with JB TW roms. Recovery is not dangerous. Its what you perform on it without proper reading is dangerous
6. No, PC odin can successfully flash a JB TW rom on to a non rooted Phone. But if it enters a boot loop install Philz kernel to do a reset from recovery
7. Its a long wait and no one knows when its gonna come. so if me, i would do it and i have been on all the JB TW roms available till now.
I would say, do it, do it the right way and you will enjoy the phone.
You can root your current ICS phone using the Philz kernel PhilZ-cwm6-XXLPY-XEN-v2.7 and then do a backup from recovery to be able to revert back with no problems.
Thank you so much for your reply... will do it today
Bienvenidos
Dude, another question... When you say JB TW version... What do you mean by TW...? I downloaded the one from sammobile PDA N7000XXLSA CSC N7000OXALSA... Is this a good one?
Yes. TW is TouchWiz, samsung Roms
You rock! Thank you so much... I will start doing this right now... Hope it doesnt die on me... I'm going to flash the PhilZ file and then work through the JB update... Crossing fingers...
anything, just update the post
Quick question... First: flash PhilZ... Then Wipe and then Odin? or do I go with Odin and then Wipe Data/Cache
first flash Philz, boot into recovery do a backup, then Odin, install Philz for XXLSA then wipe
Ok problems!!!! Flashed Philz (link you gave me) and when reboots, it doesnt get past the NOTE logo... I entered Recovery to do a backup and gonna go wo download mode with ODIN to update to JB and then do wipe from Philz... I-m scared beyond my pants if that makes sense at all...
Your current ROM is XXLPY right ?, which kernel did you install ? If you installed an ICS kernel , your phone should boot anyway, but if you installed a JB kernel then it wont
Yeah my bad... I installed a JB PhilZ kernel... I did a backup and flashed via ODIN the leaked 4.1.2... It loaded fine... , now my question is... Should I still update to the JB kernel for my version of JB? or do I stay with the one I installed... another question... should I still wipe?
OK. Main thing first. Now that you have backed up your rom, and the backup contains a JB kernel and ICS rom, so in future if you choose to restore the backup, dont be surprised if the phone does not boot. Later change the kernel to ICS
Which kernel did you install, update to your version of the kernel.
If the phone is fine, dont do a wipe. You can do it when you face some issues like Force close of apps or something not working as it should
I get it... will update the Philz to the right vkernel... Everything is working beautifully... Thank you for your support and patience!
Hi guys I'm new to the N7000 forums, but I am no means new to the android and flashing scene. I'm just a bit confused as to how to safely install ROM's on the note.
I've attached a screenshot of my "about phone" so you guys can tell me what kernel I should flash before installing different ROMs
The ROM(s) I'm interested in flashing are Jellybam, Sweet ROM (JB version) and Ultimate jellybean. Can these roms work with any safe kernel? i.e. once iv'e flashed philz or franco kernel I can let the flashing begin.
Also do I need to flash a safe kernel in order to install cyanogenmod or other, not based on stock roms?
Forgot to mention that I am rooted. Any help at all would be appreciated, if I am wrong about anything so far, feel free to set me straight.
Thanks to all who responded, if anyone else wants to reply feel free but i'm going to mark this as resolved so their won't be any confusion.
amd-dude said:
Hi guys I'm new to the N7000 forums, but I am no means new to the android and flashing scene. I'm just a bit confused as to how to safely install ROM's on the note.
I've attached a screenshot of my "about phone" so you guys can tell me what kernel I should flash before installing different ROMs
The ROM(s) I'm interested in flashing are Jellybam, Sweet ROM (JB version) and Ultimate jellybean. Can these roms work with any safe kernel? i.e. once iv'e flashed philz or franco kernel I can let the flashing begin.
Also do I need to flash a safe kernel in order to install cyanogenmod or other, not based on stock roms?
Forgot to mention that I am rooted. Any help at all would be appreciated, if I am wrong about anything so far, feel free to set me straight.
Click to expand...
Click to collapse
if you are on stock kernel then download Philz kernel for LP7, flash that in recovery, should give you root again aswell. then you can flash away to any of the ROMs you listed above. just every time you flash a ROM or think of factory reset or data wiping make SURE you're on a SAFE kernel. that's all
as you are rooted, just install any safe kernel like hydracore or philz. thats all. then you can try out any rom. Just make sure you follow the instruction to flash the rom in the OP
I saw that the Philz kernel has a lot of different versions, which one do I choose, am I right in saying the UBLPC one, as that is my build number? Or any one can work, I also read that you should not flash with the temp CWM, I will admit though I used the temp CWM to flash the root files and i'm still ok but I don't want to take any chances, how do I flash with the stock recovery?
amd-dude said:
I saw that the Philz kernel has a lot of different versions, which one do I choose, am I right in saying the UBLPC one, as that is my build number? Or any one can work, I also read that you should not flash with the temp CWM, I will admit though I used the temp CWM to flash the root files and i'm still ok but I don't want to take any chances, how do I flash with the stock recovery?
Click to expand...
Click to collapse
this is the one you use - PhilZ-cwm6-UBLPC-UUB-2.7
http://www.mediafire.com/file/35d4kd...2.7-signed.zip
the zip file mentioned above can be flashed using stock recovery. Put the file on ext SD card > boot into recovery > apply update from external storage > thats it
nokiamodeln91 said:
the zip file mentioned above can be flashed using stock recovery. Put the file on ext SD card > boot into recovery > apply update from external storage > thats it
Click to expand...
Click to collapse
First, forget about the franco kernel. The franco kernel for the Note is outdated and thus useless. Second, if you plan to flash a JB leak the only kernel you should use is PhilZ. And especially important with the JB leaks is to stick exactly to the instructions how to flash. Otherwise your phone won't even boot.
Have fun with your device! The Note is still an outstanding phone.
Sent from my revived Galaxy Note
Thanks guys for the quick replies, i'm gonna flash the philz kernel now and give the leaked version of JB a try.
make nandroid backup 1st..
Hello friends,
I need urgent help !!!
Yesterday one of my very close friend gave me his Note to upgrade to JB (he was on ICS. LF4 if I remember correct)
So I did following :
1. Downloaded couple of Custom ROMs and PhilZ 6.26.6 on to his phone (External SD)
2. Tried to boot into Recovery and voila.....his HOME button is not working. Anyways I booted and adb reboot recovery
3. Then I flashed PhilZ and it flashed successfully. Since I couldn't boot into Recovery without Home button I did Reboot System.
4. Stuck in N7000 Blackscreen and adb shows Device Offline
What I am planning to do now
1. Put device to DOWNLOAD mode through USB JIG
2. Flash Stock JB (Here's 2nd problem - download links are not working for Stock JB at least not Indian one Can somebody with fast internet plz upload it on dev host or Mediafire and share with us. Thanks !!! )
3. Reboot into Recovery and flash PhilZ
4. Flash Custom ROM
Am I doing things right? Is my direction correct?
I would still prefer if I somehow could boot in current OS, put some Custom Recovery and flash Custom ROM. Saving Stock ROM flash path and ODIN.
Plz help and advise !!!!!
Thanks !!!
You installed a kernel that doesn't fit to ICS. So it's no suprise the system doesn't boot. Install an ICS kernel and at least the system should start again.
And after that: give it back to your friend and let him repair the home button first. Don't risk being the fool who ruined his device.
Update: just read again and saw that right now you don't get a connect with adb. So yes, it seems to be the only solution to install an stock rom with Odin. After that I still would give it back for repair.
ThaiDai said:
You installed a kernel that doesn't fit to ICS. So it's no suprise the system doesn't boot. Install an ICS kernel and at least the system should start again.
And after that: give it back to your friend and let him repair the home button first. Don't risk being the fool who ruined his device.
Update: just read again and saw that right now you don't get a connect with adb. So yes, it seems to be the only solution to install an stock rom with Odin. After that I still would give it back for repair.
Click to expand...
Click to collapse
Can you give me link for safe ICS kernel ? Will this work http://www.mediafire.com/download/32ik5mg6bgg8q1d/PhilZ-cwm6-XXLRK-XEU-3.99.tar.md5
I need to boot in the current OS once to take backup of EFS (I heard JB wiped off EFS of few).
Thanks for coming forward to help !!!
Yes this is an ICS kernel with Philz recovery. Should work and give you the chance to reboot into the OS.
And a backup of EFS is a very good idea (after a repair in Thailand I'm using a developer imei).
Good luck.