i tried MBM-CI_4.3 and flackflash
that i can not unbrick this phone
how i can do it please
E:\moto\MBM-CI_4.3>.\qboot.exe blank-flash
< waiting for device >
opening device: \\.\COM44
OKAY [ 0.003s]
greeting device for command mode
OKAY [ 0.001s]
identifying device
...serial = 0x67809E4
...chip-id = 0x800 (MSM8226)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.006s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.004s]
validating files
OKAY [ 0.482s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.002s]
sending programmer
OKAY [ 0.012s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
my original firmware is 4.4.4
after my phone is bricked i cannot us method for unbrick with use MBM-CI_4.3 or flackflash
i tried 4.4.2 , 4.3 4.4.4 not unbrick
allwayse message FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet) and exit program
allwayse black screen driver Qualcomm HS-USB QDLoader 9008
not enter in recover
help me please
tks
yours post is a little confuse.
try to flash a xml ROM the one for yours device via command line.
do what is described in here in the 4° post.
i cannot access in fastboot mode
E:\moto\AMXPR_XT1063_4.4.4_KXB21.85-14_cid12_CFC_SVC.xml>mfastboot.exe flash partition gpt.bin
< waiting for device >
my phone in QDLoader mode
my computer found phone with driver Qualcomm HS-USB QDLoader 9008
its bricked
i tried unbrick with blank-flash and some problem
i hardbricked my moto x 2014. And i found a way to fix it, or that should have fixed it.
http://www.usoftsmartphone.com/t300062.html
But When i do everything and i open the .bat file i get an error message at the end.
C:\Users\USERNAME\Desktop\Blankflash\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM4
OKAY [ 0.016s]
greeting device for command mode
OKAY [ 0.000s]
identifying device
...serial = 0xSOMETHINGIHAVECENSORED
...chip-id = 0x7B4 (MSM8974_PRO)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.010s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.006s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.003s]
sending programmer
OKAY [ 0.008s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\USERNAME\Desktop\Blankflash\blankflash>pause
Press any key to continue . . .
Is there anything i can do about that?
ulriks9 said:
i hardbricked my moto x 2014. And i found a way to fix it, or that should have fixed it.
http://www.usoftsmartphone.com/t300062.html
But When i do everything and i open the .bat file i get an error message at the end.
C:\Users\USERNAME\Desktop\Blankflash\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM4
OKAY [ 0.016s]
greeting device for command mode
OKAY [ 0.000s]
identifying device
...serial = 0xSOMETHINGIHAVECENSORED
...chip-id = 0x7B4 (MSM8974_PRO)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.010s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.006s]
validating files
OKAY [ 0.001s]
switching to download mode
OKAY [ 0.001s]
greeting device for image downloading
OKAY [ 0.003s]
sending programmer
OKAY [ 0.008s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\USERNAME\Desktop\Blankflash\blankflash>pause
Press any key to continue . . .
Is there anything i can do about that?
Click to expand...
Click to collapse
No because that is not for this device. It won't work. And was it really necessary to start another thread about the same problem?
Sent from my XT1095 using Tapatalk
It says that it's for moto x 2014 (2nd gen) or is it for Verizon maybe?
Sent from my GT-N5110 using XDA Free mobile app
ulriks9 said:
It says that it's for moto x 2014 (2nd gen) or is it for Verizon maybe?
Sent from my GT-N5110 using XDA Free mobile app
Click to expand...
Click to collapse
It says it is but there are no blankflash files for the 2014 Moto X. More than likely it is the first gen Moto X files.
Sent from my XT1095 using Tapatalk
Those files are for the first gen moto x which is why it does not work. We need the second gen files which we do not have.
Sent from my XT1095 using Tapatalk
AGISCI said:
Those files are for the first gen moto x which is why it does not work. We need the second gen files which we do not have.
Sent from my XT1095 using Tapatalk
Click to expand...
Click to collapse
Is not look to moto x1 blankflash.
Msm8974 is moto x2 but i dont know why say pro becide msm8974.
Can you send again the link to test it?
Hey, I've been trying to follow a guide on how to unbrick my Moto G but I keep getting the same error:
C:\Users\perdi\Desktop\blankflash>.\qboot.exe blank-flash
opening device: \\.\COM3
OKAY [ 0.004s]
greeting device for command mode
OKAY [ 0.003s]
identifying device
...serial = 0x66CB552
...chip-id = 0x800 (MSM8226)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.009s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.006s]
validating files
OKAY [ 0.010s]
switching to download mode
OKAY [ 0.002s]
greeting device for image downloading
OKAY [ 0.002s]
sending programmer
OKAY [ 0.013s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
C:\Users\perdi\Desktop\blankflash>pause
Press any key to continue . . .
Everything goes well until I have to do that, and I would like some help.
(The guide: http://forum.xda-developers.com/moto-g/help/how-to-unbrick-moto-g-falcon-t3394788)
Thanks in advance.
opening device: \\.\COM14
OKAY [ 0.016s]
greeting device for command mode
OKAY [ -0.000s]
identifying device
...serial = 0x6A19B4B
...chip-id = 0x800 (MSM8226)
...chip-rev = 0x0
...sv-sbl = 0x0
OKAY [ 0.016s]
finding files
...programmer = programmer.mbn
...singleimage = singleimage.bin
OKAY [ 0.031s]
validating files
OKAY [ 0.016s]
switching to download mode
OKAY [ 0.000s]
greeting device for image downloading
OKAY [ 0.016s]
sending programmer
OKAY [ 0.016s]
flashing singleimage
FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet)
this is showing when i did blank flash ...
plz help!!!!!!!!!!!!
Welcome to the club.
zman01 said:
Welcome to the club.
Click to expand...
Click to collapse
plz suggest solution as soon as possible.............
For this i m very greatful to you
http://www.mobileunbrick.com/ contact them!, they can fix your Moto G2. Send them your model name(XT1068..) and send him your phone. Its located in India and costs ca. 10 Dollars for everything.
I bought a new Mainboard instead of this, because I didn't know from mobileunbrick.com.
Good Luck
EDIT: https://www.youtube.com/watch?v=WynBaVyW0oU
I am using QFIL to try and revive my X4, but I have no idea how to get into EDL mode when I cannot do anything with the device. Computer recognizes it when I plug it in as Quectel QDLoader 9008 in Ports, but that's it.
Any suggestions would be appreciated. I don't want to have to pay MOTO to fix it if possible.
I've exhausted every resource I have.
Thank you anyone that can help or at least point me in the right direction.\
EDIT: When I was eMMC Software Download app, phone shows in COM3 Download mode, but I need an XML file to flash with that tool and don't know how to get that.
I have never heard of this method. I've never hard bricked my device either. How did this happen was it by a bad flash or corrupt update? I found this https://www.droidsavvy.com/unbrick-qualcomm-mobiles/
Maybe it will help. Their may be a way to do it instead of xml. Either way it goes xml is just acompressed file with the ROM in it. Is it possible to find a file compressor with .xml format?
Knowing previous Moto phones you'll need a blankflash file that only Lenovo/Motorola has and may or may not get leaked in the future. Just to make sure, you really can't enter into fastboot mode.?
DustArma said:
Knowing previous Moto phones you'll need a blankflash file that only Lenovo/Motorola has and may or may not get leaked in the future. Just to make sure, you really can't enter into fastboot mode.?
Click to expand...
Click to collapse
No, my power went out in the middle of fastboot flashing and screwed up all the partitions. I am stuck without the blankflash.. Thank you for replying to try to help.
christopher68369 said:
I have never heard of this method. I've never hard bricked my device either. How did this happen was it by a bad flash or corrupt update? I found this https://www.droidsavvy.com/unbrick-qualcomm-mobiles/
Maybe it will help. Their may be a way to do it instead of xml. Either way it goes xml is just acompressed file with the ROM in it. Is it possible to find a file compressor with .xml format?
Click to expand...
Click to collapse
Yes, already read all of that, doesn't help. Unfortunately, I am at ground zero still.
johnjingle said:
Yes, already read all of that, doesn't help. Unfortunately, I am at ground zero still.
Click to expand...
Click to collapse
you can not take it to the Moto warranty? you do not have to know how the phone went blank...
bookworth said:
you can not take it to the Moto warranty? you do not have to know how the phone went blank...
Click to expand...
Click to collapse
u can try this blankflash.zip , run the script blank-flash.bat when you connect to PC have the 9008 port.
https ://drive.google.com/open?id=1wfNOTMquSJFcCjCtaxf1lrSPVABm9XTS (please delete the blank after https)
LazyCountry said:
u can try this blankflash.zip , run the script blank-flash.bat when you connect to PC have the 9008 port.
https ://drive.google.com/open?id=1wfNOTMquSJFcCjCtaxf1lrSPVABm9XTS (please delete the blank after https)
Click to expand...
Click to collapse
Bro! It's works! Thanks for blank-flash for my soft bricked moto x4.
O link não funciona
LazyCountry said:
u can try this blankflash.zip , run the script blank-flash.bat when you connect to PC have the 9008 port.
https ://drive.google.com/open?id=1wfNOTMquSJFcCjCtaxf1lrSPVABm9XTS (please delete the blank after https)
Click to expand...
Click to collapse
Please guy, this link not work! Help me Please. Thanks
silvamatta said:
Please guy, this link not work! Help me Please. Thanks
Click to expand...
Click to collapse
It does, if you follow his instructions stated after the link.
Consegui agora!
jhedfors said:
It does, if you follow his instructions stated after the link.
Click to expand...
Click to collapse
Thanks Very much! work perfectly
Hi. I have a similar issue where all I have is the Qualcomm QD Loader 9008 and I attempted to use the blank flash to resolve it but I got the following error:
**** Log buffer [000001] 2018-07-26_14:55:02 ****
[ 0.000] Opening device: \\.\COM6
[ 0.001] Detecting device
[ 0.004] ...cpu.id = 172 (0xac)
[ 0.004] ...cpu.sn = 2293722822 (0x88b76ec6)
[ 0.004] Opening singleimage
[ 0.005] Loading package
[ 0.006] ...filename = pkg.xml
[ 0.007] Loading programmer
[ 0.008] ...filename = programmer.elf
[ 0.008] Sending programmer
[ 0.196] Handling things over to programmer
[ 0.197] Identifying CPU version
[ 0.197] Waiting for firehose to get ready
[ 3.212] ...SDM630 1.0
[ 3.213] Determining target secure state
[ 3.215] ...secure = yes
[ 3.238] Configuring device...
[ 3.243] Flashing GPT...
[ 3.243] Flashing partition with gpt.bin
[ 3.247] Initializing storage
[ 4.421] Target NAK!
[ 4.421] ...ERROR: Failed to open the SDCC Device slot 0 partition 0
[ 4.422] ...ERROR: Failed to open the device 1 slot 0 partition 0
[ 4.423] ...INFO: Device type 1, slot 0, partition 0, error 0
[ 4.423] ...WARN: Get Info failed to open 1 slot 0, partition 0, error 0
[ 4.424] ...ERROR: Failed to get device info slot:0artition:0
[ 4.424] ...GetStorageInfo Failed - storage_device_get_info() returned FALSE
[ 4.424] ...ERROR 14: Line 1283: HANDLE_STORAGE_INFO_FAILURE
[ 4.424] ERROR: do_package()->do_recipe()->do_flash()->flash_simg()->do_package()->do_recipe()->do_flash()->gpt_flash()->get_storage()->init_storage()->firehose_do_fmt()->do_recipe()->NAK
[ 4.424] Check qboot_log.txt for more details
[ 4.425] Total time: 4.426s
[ 4.425]
[ 4.425] qboot version 3.86
[ 4.425]
[ 4.425] DEVICE {
[ 4.425] name = "\\.\COM6",
[ 4.425] flags = "0x144",
[ 4.425] addr = "0x62FD64",
[ 4.425] sahara.current_mode = "0",
[ 4.425] api.buffer = "0x2B15020",
[ 4.425] cpu.serial = "2293722822",
[ 4.425] cpu.id = "172",
[ 4.425] cpu.sv_sbl = "1",
[ 4.425] cpu.name = "SDM630",
[ 4.425] storage.type = "eMMC",
[ 4.425] sahara.programmer = "programmer.elf",
[ 4.425] module.firehose = "0x2A51630",
[ 4.425] api.firehose = "0xF2EF68",
[ 4.425] cpu.ver = "256",
[ 4.425] cpu.vername = "1.0",
[ 4.425] fh.max_packet_sz = "1048576",
[ 4.425] fh.storage_inited = "1",
[ 4.425] provisioning_may_hang = "true",
[ 4.425] }
[ 4.425]
silvamatta said:
Please guy, this link not work! Help me Please. Thanks
Click to expand...
Click to collapse
You mean you can't download ?
waltwittman1 said:
Hi. I have a similar issue where all I have is the Qualcomm QD Loader 9008 and I attempted to use the blank flash to resolve it but I got the following error: (log text omitted)
Click to expand...
Click to collapse
I got a similar error when I tried the blank-flash on my bricked Moto X4. @waltwittman1 please let me know if you find a solution.
serial_write() Error
After running blank-flash.sh with the phone connected and VolDown+Power held, I only can get this error. Anyone have any ideas or a singleimage.bin file for a Moto X4 XT1900-1 (Android One)?
Motorola qboot utility version 3.86
[ 0.000] Opening device: /dev/ttyUSB1
[ 0.000] Detecting device
[ 21.382] ...cpu.id = 172 (0xac)
[ 21.382] ...cpu.sn = 4247084357 (0xfd255d45)
[ 21.382] Opening singleimage
[ 21.382] Loading package
[ 21.384] ...filename = pkg.xml
[ 21.385] Loading programmer
[ 21.385] ...filename = programmer.elf
[ 21.385] Sending programmer
[ 21.570] Handling things over to programmer
[ 21.570] Identifying CPU version
[ 21.570] Waiting for firehose to get ready
[ 24.570] serial_write(), line 280: Input/output error
[104.005] Waiting for firehose to get ready
[107.005] serial_write(), line 280: Input/output error
ttyUSB Permissions Linux
mistryous said:
After running blank-flash.sh with the phone connected and VolDown+Power held, I only can get this error. Anyone have any ideas or a singleimage.bin file for a Moto X4 XT1900-1 (Android One)?
[ 24.570] serial_write(), line 280: Input/output error
[104.005] Waiting for firehose to get ready
[107.005] serial_write(), line 280: Input/output error
Click to expand...
Click to collapse
While I was running as root on my Linux system, this was solved as an issue between the device showing up on /dev/ttyUSB0 initially. I set permissions correctly there, but it reconnects with VolDown+Power on /dev/ttyUSB1 which had limited permissions. While udev rules could solve it, I was lucky to catch the device correctly in time to manually change the permissions and have blankflash progress all the way through. [Upon further thought root should have solved this, so it is likely just an issue with how devices/permissions are set up on my system].
Owner trashed the blankflash file. Can anyone hook me up please?
Here you go.
luvcustom said:
Owner trashed the blankflash file. Can anyone hook me up please?
Click to expand...
Click to collapse
This is the one I use. This is my first post to the XDA forums so they prevented me from linking to my dropbox. So, replace the [dot] with a . and you should be good.
.dropbox [dot] com/s/3xi85sy207x3vs6/blankflash.zip?dl=0[/url]
Win 10 waiting for device message and nothing more.
and no 9008 port
moved