I had a fully working Galaxy S3 i9300 and when I got my new phone, it's been in my drawer for a couple of months until my sister needed a temporary phone and I wanted to give this phone to her so I turned it on and it wouldn't load the OS. I charged it to 50%, still nothing.
Then I thought maybe flashing the firmware and then upgrading to a custom ROM would fix whatever the problem is. I searched around and downloaded this ROM:
http://updato.com/firmware-archive-select-model?record=7A9319A15E6411E6B055FA163EE8F90B
The flash failed. I re-tried, and it got stuck. So I restarted the phone. Now it won't respond to any input and when I connect the charger to it, it shows a white screen like the image below:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I tried to put it to download mode with no success.
What should I do? is there anything to be done?
Seems to be bricked. Most probably something messed up with boodloader. When you flashed new os did it stop in middle of doing something?
McXred said:
Seems to be bricked. Most probably something messed up with boodloader. When you flashed new os did it stop in middle of doing something?
Click to expand...
Click to collapse
Yes, it was flashing and stopped with an error.
What should I do then? Any solutions?
BTW, I used a program called 300K to go to download mode. The program said that it's on download mode but I have no idea if it's on DL Mode or not. (the screen is still the same) Then connected the phone to Odin and tried to flash again (the screen was the same though).
This is the odin log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGPE1_I9300AMNGPF1_I9300BVUGNB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone?
alirezanoori said:
Anyone?
Click to expand...
Click to collapse
You have to flash pit file. if you dont want to risk go to gsm shop
McXred said:
You have to flash pit file. if you dont want to risk go to gsm shop
Click to expand...
Click to collapse
I did that (or at least tried to do that) but since the screen doesn't share, I don't know what's going on. However, when I try, odin gets stuck on a message saying "Getting pit" or something similar.
I suggest you to use odin 3.7 for this device. Place the pit file and do repartition. I hope it help.. Good luck.
Related
hi,
sorry for my english, i'm from germany^^
i need your help:
i tried to flash my with odin3 v1.70 to I9010XXJL1, but i failed
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9010XXJL1-REV00-ALL-low-CL752194.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
my phone doesn't start anymore - just a picture looking like this:
[phone]..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
..[cpu]
thanks in advance for helping
leertaste90 said:
hi,
sorry for my english, i'm from germany^^
i need your help:
i tried to flash my with odin3 v1.70 to I9010XXJL1, but i failed
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9010XXJL1-REV00-ALL-low-CL752194.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
my phone doesn't start anymore - just a picture looking like this:
[phone]..
..[cpu]
thanks in advance for helping
Click to expand...
Click to collapse
You bricked your phone. You are going to need to go to download mode and use odin again. And from personal experience, using that i9010xxjl1 rom, it is a hit or miss, just gotta keep trying. I got it to work after flashing it a second time. You might need a Jig to get into download mode.
hmm... i got a new problem. maybe, the firmware is crap?
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> Sbl.bin
Click to expand...
Click to collapse
i got a little pice of that downloadbar on my phone screen, but it doesn't move odin does nothing, when Sbl.bin is getting downloaded to the phone.
is there an other firmware i could try?
Okay, ehhh tell me where you got the file and what you put into odin okay ) I'll help as best as I can. Worst case scenario would be flashing a different rom. And what phone do you have? Just tell me everything so I can understand and fix your problem (if I can).
=)
i got the firmware I9010XXJL1 from samfirmware.com/WEBPROTECT-i9010.htm.
i've a samsung galaxy s giorgio armani (gt-i9010).
i tried it with odin v1.0, v1.3 and v1.7... none of them worked
inside the rar file:
I9010XXJL1-REV00-ALL-low-CL752194.tar.md5
MODEM_I9010XXJK9_REV_00_CL737172_SIGNED.tar.md5
my pit-file:
s1_odin_20100512.pit
i tried it several times that way:
img6.imagebanana.com/img/0f1379it/odin.jpg (can't include external links)
thank you =)
Try rebooting your PC, use a different usb port, etc. I had same thing happen to me before. Rebooting fixed my problem.
worked!
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9010XXJL1-REV00-ALL-low-CL752194.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> boot.bin
<ID:0/010> Sbl.bin
<ID:0/010> param.lfs
<ID:0/010> factoryfs.rfs
<ID:0/010> cache.rfs
<ID:0/010> zImage
<ID:0/010> Removed!!
<ID:0/010> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
but the next problem^^
on the android system recovery <3e>:
[...]
update media. please wait
E:Can't mount /dev/block/st110
(Invalid argument)
E:copy_dbdata:media:Can't mount DBDATA:
your storage not prepared yet. please use UI me nu for format and reboot actions.
copy default media content failed.
Click to expand...
Click to collapse
what to do now?
Next problem??
Is this when you turn on the phone??? Usually it'll give you options on what to do as well...
yes,
my phone starts, galaxy intro plays, after finishing i get a black screen and it vibrates several times...
i did in 3e:
wipe date/factory reset
wipe chace partition
but it didn't helped.
Any more options? there should be more, I remember when I flashed this rom I was able to ignore that 3e warning and the phone would be back to normal.
yes:
reboot system now
apply sdcard:update.zip
wipe date/factory reset
wipe chace partition
format internal sd-card
when i start my phone, it doesn't work... it just vibrates^^
Do you already tried the reboot option then? I was afraid of that.... The part where your phone just vibrates.
Sent from my SAMSUNG-SGH-I897 using XDA App
yes, doesn't work any other ideas?
I have an idea, but first, can you still get into download mode? If yes, I can still help you ^^
Sent from my SAMSUNG-SGH-I897 using XDA App
yes, i can get into download mode
now i downloaded i9010XXJK9_XXJL1_OXA including:
1. GT-I9010-CSC-MULTI-OXA725151[1].tar.md5
2. I9010XXJL1-REV00-ALL-low-CL752194.tar.md5
3. MODEM_I9010XXJK9_REV_00_CL737172_SIGNED.tar.md5
4. SP6160.axf
where to put these files on odin? the first at CSC, the second at PDA. but last two?
hoooooooooo, it works again! hahah, yeah i like
thank you sooooo much for helping =)
Well I'm glad you got it working. Sorry for the delayed response, I passed out. But reason why you messed up was because of two things. I did the same mistake myself as well when I flashed this rom.
1. When you used Odin, you only use the .pit file if you needed to repartiton and if you have 3 files (Phone/PDA/CSC) Since samfirmware.com was stupid when they released this. They didn't have the third file (CSC) so the only way to flash this rom was to use the 1 file method. You only needed to put the i9010xxjl2 file into the PDA section and simply flash the rom.
(But it looked like you got a different i9010 rom and were able to flash it)
2. When you were in the android 3e directory, that's what the .pit file do and the lack of a CSC file caused the data/cache wipe and partition to do nothing but send your phone into a blank screen.
I guess with this information, I might as well post the guide to flash the i9010 Armani Froyo rom >.<
Leertaste,
where did you download these files and where do they go in odin?
i'm having the same problem as you had..
please let me know
leertaste90 said:
now i downloaded i9010XXJK9_XXJL1_OXA including:
1. GT-I9010-CSC-MULTI-OXA725151[1].tar.md5
2. I9010XXJL1-REV00-ALL-low-CL752194.tar.md5
3. MODEM_I9010XXJK9_REV_00_CL737172_SIGNED.tar.md5
4. SP6160.axf
where to put these files on odin? the first at CSC, the second at PDA. but last two?
Click to expand...
Click to collapse
Where you install the number 4? on Odin?
Hey everybody,
I have a question regarding CDMA Galaxy Tab (SCH-I800). Basically what happened - it boot looped after factory data reset, getting stuck on Verizon Wireless logo. Accessing Recovery and trying to wipe data/factory reset or wipe cache partition does not help. Tried Odin with VerizonEC0.tar.md5 to reset - nothing happens. Tried galaxy cubed throught Heimdall - nothing. I tried basically every options out there in the forum and the most I'm getting is the message on the picture.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Before you say anything like "use search button before asking questions", I did. Searched Google, XDA specifically going page by page and every solution out there that worked with someone is not working for me.
Any help? Ideas? Would really appreciate your help.
probably hosed NAND chip.
What did you do to start with?
It was stock condition and you just decide to do factory reset? Or something else has happened?
The odin and heimdall --> nothing happen
can you elaborate?
The tab just sitting there no reaction?
priyana said:
probably hosed NAND chip.
What did you do to start with?
It was stock condition and you just decide to do factory reset? Or something else has happened?
The odin and heimdall --> nothing happen
can you elaborate?
The tab just sitting there no reaction?
Click to expand...
Click to collapse
It was stock, so to get it ready for sale, i just did the factory reset ( I must clarify that before stock, i had ICS beta installed there, but switched back to stock since camera wasnt working in ICS beta).
Well, I searched for stock files for my tab, and some of them where flashable through Odin, some through Heimdall. Both ways when I flash it shows as the process complete. But after it reboots - it just stays in boot loop. This is what Odin had last time I flashed the device:
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> verizonEC02.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Get PIT for mapping..
<ID:0/017> Firmware update start..
<ID:0/017> cache.rfs
<ID:0/017> NAND Write Start!!
<ID:0/017> factoryfs.rfs
<ID:0/017> modem.bin
<ID:0/017> param.lfs
<ID:0/017> zImage
<ID:0/017> RQT_CLOSE !!
<ID:0/017> RES OK !!
<ID:0/017> Removed!!
<ID:0/017> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
It seems as thought It writes fine, it feels like there is a mounting problem for /data and /cache directories. And I cant install CWM recovery, to have an option to try and mount those partitions manually
Hi Experts,
Today I lost main DCIM gallery on my Samsung Note 5. I tried to use Dr.Fone application in standard and avanced mode. At the end of the day I didn't manage to retrieve any data. The worst thing is I cannot startup my phone due to "Recovery is not Seandroid Enforcing" error.
I downloaded Singtel Firmware but in Odin3 I get error as follows:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Could you please let me know what do I do wrong? By any chance can I recover my phone settings without flashing any data? I still have a hope I will be able to retrieve lost pictures from my gallery.
Thanks and Regards,
KM
What I would like to add below is the message on my Samsung Note 5 after Odin3 failed:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-N920I
CURRENT BINARY: Custom
SYSTEM STATUS: Official
FRP LOCK: OFF
Secure Download : Enabled
KNOX WARRANTY VOID: 1 (0x0500)
RP SWREV: B:2 K:0 S:0
SW REV. CHECK FAIIL. DEVICE: 2, BINARY: 1
How can I proceed with this case?
So will trip Knox on my Sammy devices ?
Hi there.
My galaxy note 5 (unlocked) was working very well until yesterday
Some apps start crashing and start to slow down
And after it suddenly restarted and stuck in a restart boot
I tried a lot of ways to fix it began of:
- Boot it in safe mode (the apps still crashing)
- Wipe the cache partition
- Wide data factory
- And after that i treid to install stock firmware with odin i followed all the instruction. But Odin still showing FAILED
and this message :
-----------------------------------------------------------
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
---------------------------------------------------------------------
I activated the USB debugging and OEM unlocking btw.
Your help will be highly a appreciated
And thakns.
if you are rooted then you cannot fash it with odin now try smart switch. this software is samsung's official and will flash official firmware on your note 5.
No, I never rooted my phone !
And for the smart switch that was my try.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Try
Android Recovery
- Wide data factory
- Wipe the cache partition
-reboot to bootloader
itthipon555 said:
Try
Android Recovery
- Wide data factory
- Wipe the cache partition
-reboot to bootloader
Click to expand...
Click to collapse
I tried the first two ! and still have the same issue.
But what is the reboot to bootloader
Flash a custom Rom from twrp
godkingofcanada said:
Flash a custom Rom from twrp
Click to expand...
Click to collapse
Can you please give me a guide on how to do that ?
Yahya Joud said:
Can you please give me a guide on how to do that ?
Click to expand...
Click to collapse
You download twrp recovery here on xda for your device and flash it via Odin. Then put a custom Rom ( I recommend Dr ketan note 5 Rom). Also found here on xda, put it onto sdcard or if you have the usb flash drive adapter or you can probably even adb connect and push the zip if the other two aren't options. Then you flash the zip from twrp recovery menu(it takes the place of stock recovery. The one you hold power and volume up to get to.
note 5 920T need help
coolsongs95 said:
if you are rooted then you cannot fash it with odin now try smart switch. this software is samsung's official and will flash official firmware on your note 5.
Click to expand...
Click to collapse
i have the same problem,my phone is not rooted when i installed the firmware for 920T
it keeps turning on and off,i tried to install the firmware again in vain but it did not work .let me know please
If anyone says something about "if you are rooted you can't use odin" don't believe it!
I was rooted with TWRP installed and even xposed and still i could use odin to flash stock.
Are you flashing everything like bootloader and all this stuff? Do it if you didn't.
Else if you need backup rom i recommend "[ROM][7.0][MYSTYLEROM][N920CGI][RL3][19-01-19]".
It's the best backup rom in my opinion.
Try downloading the stock rom from different site again. Maybe rom is damaged.
And also try to
Yahya Joud said:
Hi there.
My galaxy note 5 (unlocked) was working very well until yesterday
Some apps start crashing and start to slow down
And after it suddenly restarted and stuck in a restart boot
I tried a lot of ways to fix it began of:
- Boot it in safe mode (the apps still crashing)
- Wipe the cache partition
- Wide data factory
- And after that i treid to install stock firmware with odin i followed all the instruction. But Odin still showing FAILED
and this message :
-----------------------------------------------------------
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
---------------------------------------------------------------------
I activated the USB debugging and OEM unlocking btw.
Your help will be highly a appreciated
And thakns.
Click to expand...
Click to collapse
Put the firmware in "AP" in odin. make sure you download the latest stock firmware because when i tried flashing a one month old firmware few months ago it said 'failed' so go on sammobile and check the latest version for your country and model number
Boot into download mode by holding power, volume down and home button together.
This will get you to download mode (odin mode)
Now connect to your pc and open odin
select AP and choose the md5 file you downloaded and click Start.
Then your phone will restart
Sent from my Note 5 using XDA Labs
Try this. Worked for me on n920c
my sm-n920c binary 3 was working properly however the phone crushed with OEM & Debug all switched off.
firstly i wiped data, factory reset because it was saying "custom rom blocked by frp".
second i tried installing new firmware but frp is on.
third i used smart key tool to remove frp but it resulted in removing the custom rom and drk.
fourth i installed new eng boot file
now im stuck at trying to installing new sboot file therefore i cant install new firmware.
please help atleast link me to any sboot.tar.md5 and perharps a latest n920c binary 3 file
For the past 2 years I have been loving my rooted Note 4, always keeping up with the most recent firmware. However, this week I have been having trouble getting out of a bootloop on my SM-N910T.
Last time my phone was broken, KIES was able to help reset it. So this time, I started by trying to use KIES once again. Unfortunately, I got the message "the connected device is not supported by KIES" once it is plugged in. When I try firmware upgrade and initialization in kies, I get the error "SM-N910T" does not support initializing. I get this same error message when I tried using an older version of smartswitch that still allows for initializing.
Since KIES/Smartswitch had failed, I tried downloading the most recent firmware from sammobile and pushing it to the device using ODIN, which I run as an administrator. To do this, I followed the instructions in this video , which asks you to first factory reset and format the system. I did this on my phone using TWRP and even tried wiping the dalvik cache, the system, the data, the internal storage and the cache. I then tried using ODIN to push the firmware while the phone is in download mode. When I plug in the phone, the blue box shows up in odin indicating that the drivers are updated. Despite this, I keep getting stuck on the step called "aboot.mbn". It stays on this step for about an hour before reading "XmitData_Write." After these attempts, the phone no longer
I have tried using an older version of ODIN and even a different version of the firmware. I have also found a .PIT file unique to the phone (here) to re-partition the phone but that failed as well saying it could not be re-partitioned.
Any suggestions would be greatly appreciated!
Picture of ODIN:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ODIN Log:
<OSM> N910TUVU2EQI2_N910TTMB2EQI2_N910TUVU2EQI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> __XmitData_Write
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i had the same problem i had to use a different usb cable