Related
I love my Nexus S. Yes, the build quality is plastic, yet anything but cheap. I've seen a lot of compliments on the slick back cover (battery door). However, it's not to my taste. I find it to be overly reflective, a fingerprint magnet, and slippery to the point where I would drop my phone if it were not for the reverse chin.
Solution: DIY Soft touch battery door (rubberized back cover)
I simply applied four thin layers of spray on black PlastiDip. As in the instructions, make sure to shake the can thoroughly for a full minute and keep the can of PlastiDip a full 12-16 inches from the back cover of the phone. Wait a full 30 minutes between coats. Make sure to spray all the way around the edge of the battery door into the back of the cover. If you do not coat the edge your coating will eventually begin to peel at the edge. The easiest method is probably to mask off the contacts for the NFC antenna and spray the entire cover, inside and out. That way there is no rubber seam to peel at the edge.
Here are the results. I think the images phone2.jpg and phone3.jpg most accurately show the results. The closeups tend to make the cover look more textured than it actually appears.
PlastiDip is easily peeled off if you start at an edge, but difficult to peel off unintentionally. If I ever get bored with the finish or want to sell the phone I can remove the rubber within seconds.
yeah i used this for my galaxy S, pretty good idea actually lol
I like it. Did you sand before painting? If so what grade? Thanks in advance.
No sanding required. Just a thorough cleaning with water then spray on PlastiDip.
Sent from my Nexus S using Tapatalk
AndroidMilos said:
I like it. Did you sand before painting? If so what grade? Thanks in advance.
Click to expand...
Click to collapse
I dont think any sanding is needed because it simply peels off.
Is plastidip messy? because I'm gonna try this when I get home but it 20F outside and Im not wait thirty mins between coats in such weather lol. So I hope its doable in the house. However when I do mine I might put tape over the Google logo and peel it off after all dry and clean because I dont wanna lose that, I could careless about the samsung tho lol
Whats great is you dont need to sand and ruin the cover and simply peels off.
Thanks for sharing think im going to try this, might do clear color
I wonder if Walmart sells PlastiDip
Sent from my Nexus S using XDA App
Smilez_c said:
I wonder if Walmart sells PlastiDip
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
I looked online and ace hardware, home depot and lowes carry it
That looks better than I thought it would. I think it's time to take a trip to Home Depot
demo23019 said:
I looked online and ace hardware, home depot and lowes carry it
Click to expand...
Click to collapse
Thanks bro. I'll stop by Home Depot after work I guess
Sent from my Nexus S using XDA App
But what about other cases or the front of the phone? You can't fit a regular cases now or any sort of holster. How is it in the pocket?
hah2110 said:
But what about other cases or the front of the phone? You can't fit a regular cases now or any sort of holster. How is it in the pocket?
Click to expand...
Click to collapse
Even with four thin coats, it doesn't add enough bulk to prevent another case from fitting on the phone. For the screen, I use a Zagg for now until something better comes out. As for the feel in the pocket it is a little tacky. It doesn't slide in and out of the pocket as smoothly as I'd like, but in my opinion it's a necessary trade off. I still prefer the rubberized back.
Sent from my Nexus S using Tapatalk
But what happens if you put a holster/case on? Won't it degrade the rubber?
What about the NFC chip? this is what worries me about the Nexus S, the NFC relies on this "cheap, plastic" cover... The NFC chip needs to be within centimeters of the other object's NFC chip. Wouldn't this interfere? Anyone try after applying a case or using this rubberized method?
This coating doesn't add centimeters of thickness to the back, so it should be fine.
Just make sure u hold can 12"-16" from cover I was too close on my first coat so I sprayed too much on there. But it looks fine
Sent from my Nexus S using XDA App
demo23019 said:
I looked online and ace hardware, home depot and lowes carry it
Click to expand...
Click to collapse
What exactly is it called? "PlastiDip" ? I searched for that on Lowe's website and found nothing.
Home Depot's site is down right now for maintenance, at 7pm on the west coast.. wtf Home Depot, get your act together.
Smilez_c said:
Just make sure u hold can 12"-16" from cover I was too close on my first coat so I sprayed too much on there. But it looks fine
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
Many thin layers works best. Also, you have to make sure the rubber on the sides is as thick as the back, and spray it all the way around the lip of the battery door. If you don't coat around the edge into the inside of the battery door your rubber will eventually begin to peel at the edge.
Sent from my Nexus S using Tapatalk
mhaedo said:
Many thin layers works best. Also, you have to make sure the rubber on the sides is as thick as the back, and spray it all the way around the lip of the battery door. If you don't coat around the edge into the inside of the battery door your rubber will eventually begin to peel at the edge.
Sent from my Nexus S using Tapatalk
Click to expand...
Click to collapse
Thanks a lot bro.... I peeled off the the first try it wasnt bad but i got the hang of it now im trying to be perfect
The best case so far is the Griffin survivor knockoff but it is very cheaply made. The screen protector scratches very easily. Does anyone have an idea where I could get the material used for the screen protector that Otterbox uses ?
Otterbox defender has a good quality protector but unfortunately it has cutouts for the home button as well as the top Speaker.
ARE there any other options ? Does anyone have any ideas how to dust proof the Otterbox?
Dust definitely is a problem with this case. I end up taking it apart to clean a couple of times a day, which sounds worse than it really is, even to me - When I think about it, I'm like, "Ugh, what a pain", but then, after, I'm like, "That wasn't so bad".
Anyway, in response to your question, I do have an idea, but haven't tried it and probably won't because I don't mind the cleaning.
You could cut to size and glue rubber washers to the inside of the screen, outlining the cutouts.
Tape. Put a small piece non sticky side up over the home button opening then tape it down from the inside do the same with the speaker cutout and use a needle to perforate it. If you're good with an exacto knife you could cut colored tape to fill the opening then use a small strip of crystal clear packing tape to seal it into place. It's cheap and easily replaceable when dust gets stuck to it. It'll serve 2 purposes of helping block the dust and catching what sneaks by.
☆SoA: Son's of Android™☆
I like to break stuff!
What is the point?? You might as well put it in a glass case and never touch it. It's not a mickey mantle rookie card, it's a frikin phone.
Sent from my SAMSUNG-SGH-I317 using Tapatalk 2
LittleRedDot said:
What is the point?? You might as well put it in a glass case and never touch it. It's not a mickey mantle rookie card, it's a frikin phone.
Sent from my SAMSUNG-SGH-I317 using Tapatalk 2
Click to expand...
Click to collapse
Some people work in environments with lots of silica dust which will destroy the screen in no time. It's no fun to have a hazy scuffed up screen on your $700 phone.
☆SoA: Son's of Android™☆
I like to break stuff!
If I worked in an environment prone to dust/sand, I'd have an otterbox no doubt!
I don't mind a few scratches on my phones body/midframe but my screen must stay relatively pristine. Scratches on my viewing area drive me insane :thumbdown: luckily I have an office job, but I do live in Florida and there's lots of sand around to wreak havok on your screen. For that reason alone I never put mine in a pocket cuz I prefer my glass naked, so I use a microfiber/microsuede lined leather holster with the bottom corners open so the sand and dust can fall out easily.
☆SoA: Son's of Android™☆
I like to break stuff!
apallohadas said:
If I worked in an environment prone to dust/sand, I'd have an otterbox no doubt!
Click to expand...
Click to collapse
Defender for Note 2 won't save you from dust. For someone working in such harsh environment, I wouldn't even recommend getting N2 but rather S3 with Otterbox Armor soon to be released. Seidio OBEX might work as well. But those are not for N2
+1 for survivor case..that is what we can get for now on our note 2..
Sent from my GT-N7100 using xda app-developers app
Delete
I guess I don't see how taping over the speaker and the punching tiny holes in the tape solves anything. Also tape would peel and get dirty. Just put a quality sp on and buy a good case, then leave everything else up to the gods.
Sent from my SAMSUNG-SGH-I317 using Tapatalk 2
Tape costs a few bucks for a big roll. When it peels you replace it, same with getting dusty. Thats the whole point of using tape so the dust sticks to it instead of getting and and being able to move around. As for perforating the tape, a few small holes is much harder for dust to get thru than a large opening, but will let the sound thru fairly well. Obviously you've never had to protect electronics in a harsh environment. One of the most common things done to protect ordinary electronics in the desert is put tape over the ports to prevent sand from getting in. Same in wet environments only you use heavier tape like no residue duct tape.
☆SoA: Son's of Android™☆
I like to break stuff!
I found this on Amazon and remembered seeing this post. Figured I'd bring it to your attention. I was looking at the zero lemon battery and stumbled on this. Waterproof and dust proof.
summercomm-- Waterproof Skin Case for Samsung Galaxy Note 2 N7100 Multi Purpose Protective Skin for Underwater Activity, Fishing, Ski, Snowboarding, Sand-proof, Dustproof, Bath Tub
http://www.amazon.com/dp/B00B5A16R0/ref=cm_sw_r_an_am_ap_am_us?ie=UTF8
Sent from the lab whilst Pinky and the Brain try to take over the world.
I just had a marvelous idea. Put the phone in a zip lock bag and use a bluetooth earpiece. :good:
-EViL-KoNCEPTz- said:
Tape costs a few bucks for a big roll. When it peels you replace it, same with getting dusty. Thats the whole point of using tape so the dust sticks to it instead of getting and and being able to move around. As for perforating the tape, a few small holes is much harder for dust to get thru than a large opening, but will let the sound thru fairly well. Obviously you've never had to protect electronics in a harsh environment. One of the most common things done to protect ordinary electronics in the desert is put tape over the ports to prevent sand from getting in. Same in wet environments only you use heavier tape like no residue duct tape.
☆SoA: Son's of Android™☆
I like to break stuff!
Click to expand...
Click to collapse
Yes obviously, because you know me, I've never had to protect my device in the desert.
But you would be wrong, I did 4 combat tours in Iraq and I never had a problem with a screen protector and a case. I been in sandstorms so bad you couldn't see in front of your face and I've never damaged a device. So before you go assuming things that you know nothing about maybe you should stop and think before you put your foot I your mouth.
In fact I still have the ipod I took with me and it works perfectly, as did my mates.
Sent from my SAMSUNG-SGH-I317 using Tapatalk 2
I have the book type flip case with holes on the flip cover for accepting calls and all that stuff but its not dust proof and I hate it..dust gets to my screen everytime and it damages my chrome bezel and back cover
Nice to see Samsung going with a premium metal finish and it does look stunning when new but 2 weeks down the line and it is covered in tiny scratches etc...
I look after my phones, tbh I'm a little bit OCD but even still the edge is looking tatty.
I then got a TPU case to try and protect it... 2 days later, it is scratched to hell! Just the case alone touching the chamfered edge is enough to scuff it...
what did Samsung make it out of? Cheese? A soft cheese at that!
I love my note 4 but...
I have the same experience. Maybe if it gets too bad I'll try the method used in this video.
http://youtu.be/EZuYzQrIHjA
Sent from my SM-N910T using XDA Free mobile app
MadfishGTB said:
Nice to see Samsung going with a premium metal finish and it does look stunning when new but 2 weeks down the line and it is covered in tiny scratches etc...
I look after my phones, tbh I'm a little bit OCD but even still the edge is looking tatty.
I then got a TPU case to try and protect it... 2 days later, it is scratched to hell! Just the case alone touching the chamfered edge is enough to scuff it...
what did Samsung make it out of? Cheese? A soft cheese at that!
I love my note 4 but...
Click to expand...
Click to collapse
Is this the white or black version you are talking about?
I've got the Ringke Slim on mine and it covers the edges. No scratches on mine.
It's the black one I have...
the coloured part is immaculate still but the polished section looks a mess
My note 2 seemed to fair much better in terms of durability.
Also, the camera lens cover is very exposed on these, I hope it can be replaced somehow in the future (although no scratches yet)
Same here with the white one. Got scratches on the chamfered edge from being in a pants pocket for gods sake. Anybody know to go about buffing them out?
Sorry to hear that you are having those problems. I am not trying to burst your bubble but the "metal" finish around the Note 4 is NOT metal. I have have read a post on this forum of another person saying the same thing and so I went down to my nearest BB to check it out. I am now convinced that he was right.
Here is the test I carried out to prove the point. I found a Galaxy Alpha and examined the similar finish and that is truly metal. With the AC in Best Buy I was able to put the Alpha to my cheek and you can feel the coldness of the metal. I then walked over to the Samsung store in BB and did the same with ALL the Note 4s on display and they were all just at reasonable temp. Also on the Alpha it will be noticed that the headphone jack and the charging port is covered in plastic or rubber inside of the metal cutout. Take a look at he N4 slot for the pen or the headphone jack and you will see that the white plastic is just covered by the " metal" finish.
That my friend is why you are having scuff marks already on your new device. It is JUST a "METAL" finish on the outside. Now if there is a metal frame it is on the inside, not on the outside like the Alpha. Can't wait to see a teardown from folks like IFIXIT to confirm. I could be wrong but until proven wrong I will stand by my cheek test.
No, it is metal (aluminium I believe ) but it is very thin. When you look at the headphone jack port like you say there is plastic but there is still a thin metal part of the frame...
Samsung wouldn't have needed to add the spacers in the frame (small white blocks top and bottom) if it was metal effect. These are there for the antennas to work properly in the metal.
Aluminium is a very soft metal, perhaps if they chose a more sturdy, harder metal like titanium for example then we wouldn't be having this problem but then we would have paid more for the already expensive phone.
For me I'll just end up keeping the TPU case on, it feels better in the hand and against the ear (metal frame has quite sharp edges) and offers some protection without adding much bulk to the device. Maybe once the phone has been used a while I'll look into customising the frame with either plastidip or hydroprint.
Yeah it would be made of aluminium. People wanting that "premium" look and feel. Just like the iPhone and any other phone made of an alloy, looks awesome out of the box but after a while scratches will appear. Plastic resists much much better, that's just the way it is.
Also it would have been hilarious watching you going around touching the bezels with your face
remove the back cover and look at the frame closely: you can see that the whole frame is definitely NOT metal. it is plastic with metal coating or layer and some metal inlays.
I highly doubt that the frame only has a metal coating. If you check the YouTube video of the guy bending the ip6p, note 3 and 4 you will see the note 3 bend and bounce back because it's plastic. Alloy on the other hand bends and stays bent. Looking at you note 4.
Of course I could be wrong.
It does seem to be a thin metal covering over a plastic frame...
gives the look of a premium device but the protection and flexibility of a plastic device
The frame is made of metals collected from the moon and the back cover leather is made from the skin of puppies.
Sent from my SM-N910W8 using Tapatalk
Whether its a thin metal strip on the top or solid metal, the nature of being aluminium is that it will scratch easily. It is the same with the HTC One that also has a chamfered edge. I have read many reports of it getting scratched too easily. If you look closely at the edge you will see that at the very least it is a metal strip. Thickness has nothing to do with scratch resistance. So we can argue whether it's solid or not, but the relevance to the initial poster's issue that it scratches easily is zero!
Everyone complained about Samsung's cheap looking plastic bezel. Now we are complaining about the upmarket stylish metal one! I guess a finish like the edges of an iPhone 6 are the only option that will satisfy everyone's needs. Incidentally I do remember reports of people with the bumper case on an iphone 4...took it off, to find that the little imperfection nodules of plastic on the inside of the bumper were enough to rub and wear the metal surround of the phone!
And if they had anodized it, it would have prevented scratches (like Nokia n8),but would have caused the frame to crack more easily, unless they used more surface, or thicker pieces of aluminum, which in turn would affect other things. So pointless.
Sent from my SM-N910W8
Even if it was made of adamantium people would still complain.
eddhard said:
Even if it was made of adamantium people would still complain.
Click to expand...
Click to collapse
Couldn't agree more!
Sent from my SM-N910C using Tapatalk
you do know that aluminium and metal phones get scratched up this easy i dont know why ya'll are surprised
hello00 said:
you do know that aluminium and metal phones get scratched up this easy i dont know why ya'll are surprised
Click to expand...
Click to collapse
Even in manufacturing these metals are impossible to keep pristine. I had an iPhone 4 with a small nick in the metal band out of the box. I had an HTC One with a couple of little nicks and microscratches in the band out of the box. And my note 4 also has a few imperfections. But then it's best not to study these phones under a spotlight because you will just find things you don't want to see!
I think/hope the issue lies with TPU cases simply because they, as all cases trap dirt under them but because they are TPU they have more movement.... the dirt gets ground against the polished edges. Hard cases like the Ringke do not have this movement...
Would be helpful to others if people who are experiencing this issue state which cases they have used.
Thanks.
Hello gyuz,
As mentioned in another thread in Accessories sub-forum, while Installing the Whitestone Dome Screen Protector (https://www.whitestonedome.com/) on my Samsung Galaxy Note 8, there was UV glue spillage all around the phone & now I have dried (UV cured) glue in the tiniest gap between the screen edges and the metal frame of the phone. Please check attached image, I have circled with red the exact location of the glue, however imagine this almost all around the phone:
Now I need a good UV glue remover to soften the dried glue and an extremely thin blade (or a similar tool) to reach in the gap and remove it. I saw some products on ebay, however I am not sure which will do the job.
First of all which Glue Remover is more suitable? Does it have to be a branded one? Or the unbranded ones will do the job as well? Is there danger that the remover will dry and stay in the gap making it worse? Will it damage the color or consistency of the metal frame? Will it damage the buttons (Power, Volum, Bixby)?
Secondly, which tool should do the job reaching such tiny gap while at the same time not scratching the screen or the metal frame? Metal Blade? Plastic Blade? Wire? Some other tool?
Please advise, as I am nearly desperate. Thank you!
Damn, I'm sorry you're having to deal with this. This is one of the biggest reasons why I don't use screen protectors on my phones. I've used a glass one on my Note 5 but didn't like it. Naked display feels the best and performs the best. Not fuss, no glue, no BS. Eeek!
roaduardo said:
Damn, I'm sorry you're having to deal with this. This is one of the biggest reasons why I don't use screen protectors on my phones. I've used a glass one on my Note 5 but didn't like it. Naked display feels the best and performs the best. Not fuss, no glue, no BS. Eeek!
Click to expand...
Click to collapse
Agree with everything. if i had the chance again I would leave it naked, however I would still feel very uncomfortable without protection.. Actual screen exposed to everything is a little risky!
OP, wish I could advise you, but all I can say is take your time and don't rush this task. Since as you aware, you don't want to use a chemical or item that will damage the frame or buttons. Don't use any metal objects.
Feel for you bro, you go ahead with good intentions to protect your device and now in a predicament.
Sent from my SM-N950U using Tapatalk
Limeybastard said:
OP, wish I could advise you, but all I can say is take your time and don't rush this task. Since as you aware, you don't want to use a chemical or item that will damage the frame or buttons. Don't use any metal objects.
Feel for you bro, you go ahead with good intentions to protect your device and now in a predicament.
Sent from my SM-N950U using Tapatalk
Click to expand...
Click to collapse
Thanks for your understanding mate. Indeed tried for the best and ended up worse.
I am not rushing for now, just conctacted Whitestone themselves asking advise on how to fix it, as well as an ebay seller that sells such equipment/tools. He suggested me these:
http://ebay.eu/2g3RySr
http://ebay.eu/2kATYJV
I am not sure about the quality of the Glue Remover and how thin the tools (blades & spudger) are though. Have to make a little research.
That is why also I opened the thread to ask for opinions from people that may have done this or similar task before and to help others in the future.
Warlord1981 said:
Thanks for your understanding mate. Indeed tried for the best and ended up worse.
I am not rushing for now, just conctacted Whitestone themselves asking advise on how to fix it, as well as an ebay seller that sells such equipment/tools. He suggested me these:
http://ebay.eu/2g3RySr
http://ebay.eu/2kATYJV
I am not sure about the quality of the Glue Remover and how thin the tools (blades & spudger) are though. Have to make a little research.
That is why also I opened the thread to ask for opinions from people that may have done this or similar task before and to help others in the future.
Click to expand...
Click to collapse
Before using any chemicals, I would try and use the finest /thinnest plastic card or tool to scrape the glue out of the edges first. Chemicals would be my last resort. Good luck my friend.:good:
roaduardo said:
Damn, I'm sorry you're having to deal with this. This is one of the biggest reasons why I don't use screen protectors on my phones. I've used a glass one on my Note 5 but didn't like it. Naked display feels the best and performs the best. Not fuss, no glue, no BS. Eeek!
Click to expand...
Click to collapse
I have dropped my phones at least 5 times in the last year and each time it landed screen side down. I broke all 5 glass protectors but never the screen. That is why I must have a full adhesive glass protector on. It is a PITA to get perfect but for me, it's worth it.
Mike02z said:
I have dropped my phones at least 5 times in the last year and each time it landed screen side down. I broke all 5 glass protectors but never the screen. That is why I must have a full adhesive glass protector on. It is a PITA to get perfect but for me, it's worth it.
Click to expand...
Click to collapse
I understand, some people need it. I haven't chipped or broken a display since I had an iPhone. Knock wood. Naked is glorious, though.
Plastic tools and alcohol are your friends.
99% Isopropyl should be able to dissolve the glue, and shouldn't leave a mark on the phone (iso evaporates completely and is not dangerous to plastics or metals). A stiff bristled plastic brush would be ideal, maybe an old toothbrush. The thinner and stiffer the bristles, the better.
The iso will dissolve the glue, but you'll need to mechanically agitate it to remove it completely. Bear in mind that traces of iso having touched the glue will streak glass , so a second/third rinse with iso may be necessary.
I'd be careful about getting iso into the switches, as long term iso can degrade rubber (switch seals etc) but as long as you clean, then dry out effectively there shouldn't be an issue (iso will evaporate at room temp in any case). Covering the switches with tape could help, but iso is so thin it will probably go under the tape, and will likely dissolve the glue on the tape too!
e: Whatever you do don't use acetone or any other stronger solvent. Depending on the plastics used acetone will eat right through them, and may affect the finish on other parts too.
Iso really is a decent cleaning solution for most electronic devices.
e ii: Oh, and if you use an old toothbrush, make sure it's very clean. Getting some toothpaste grit on the screen and rubbing it in with a brush would be tragic. Maybe even buy a brand new brush just for this job? Not too expensive for the job, imho.
Limeybastard said:
Before using any chemicals, I would try and use the finest /thinnest plastic card or tool to scrape the glue out of the edges first. Chemicals would be my last resort. Good luck my friend.:good:
Click to expand...
Click to collapse
Yes I'm trying to find such thin tool made of plastic. Cards are too thick for it. It needs to be so thin that can cut you..like razor blades maybe even thinner.
Warlord1981 said:
Yes I'm trying to find such thin tool made of plastic. Cards are too thick for it. It needs to be so thin that can cut you..like razor blades maybe even thinner.
Click to expand...
Click to collapse
Packaging plastic is often thin and stiff... Cut it into a triangle and see if you can get "under" the glue in the gap.
roaduardo said:
I understand, some people need it. I haven't chipped or broken a display since I had an iPhone. Knock wood. Naked is glorious, though.
Click to expand...
Click to collapse
HAHAH, SNAP! Same here, last phone I ever broke was my last iphone I owned , it was the iphone 4s. That was when I was drinking also,
Nekid, is always glorious, without a shadow of a doubt. But I am too shy and need coverage.
iPhone screens can be so brittle. I got used to changing screens for friends at work. During lunch they'd bring me their replacement display kits that they ordered from Ebay and I'd replace their broken screen for some Subway (as payment).
Warlord1981 said:
Yes I'm trying to find such thin tool made of plastic. Cards are too thick for it. It needs to be so thin that can cut you..like razor blades maybe even thinner.
Click to expand...
Click to collapse
Indeed, but not metal.
What i used after installing the whitedome was a sheet of paper, running the corner around gap. Cleaned it easily this way.
princeasi said:
What i used after installing the whitedome was a sheet of paper, running the corner around gap. Cleaned it easily this way.
Click to expand...
Click to collapse
I think OP needs something as thin but stiffer as his glue is cured fully now.
Sent from my SM-N950U using Tapatalk
Limeybastard said:
I think OP needs something as thin but stiffer as his glue is cured fully now.
Click to expand...
Click to collapse
The glue stays soft. If you run the paper around it, it will come up. After about a half a cycle thru, I would cut the edge of the paper each time so that I can continue with a firm edge. I did this after a week of installation.
princeasi said:
The glue stays soft. If you run the paper around it, it will come up. After about a half a cycle thru, I would cut the edge of the paper each time so that I can continue with a firm edge. I did this after a week of installation.
Click to expand...
Click to collapse
Guyz you won't believe it! For the past 2 hours I was doing exactly that! Actually what worked best was a piece of paper that had the dust removal stickers on it (got it from the Olixar Sentinel Case/Screen Protector kit), which is more firm than plain A4 paper. And I was cutting it all the time to keep its sharpness. At some point it finished and I used just plain A4 paper, which wasn't the same but it kinda worked as well..
I was running it inch by inch around the whole frame, taking out glue (indeed soft) little by little! I think it's much better now, though I think I will do another round in the near future.
well after watching videos.. I could see I never needed ALL of that small tube of glue. I always use some kind of screen protector. I like to sell or give away. And you can ALWAYS tell the used phones that never had a screen protector. Always some kind of scratches.. For me selling it mint.. gets more money.
So use some kind of plastic not metal blade to get the excess glue off. It comes off so easily
Warlord1981 said:
First of all which Glue Remover is more suitable? Does it have to be a branded one? Or the unbranded ones will do the job as well? Is there danger that the remover will dry and stay in the gap making it worse? Will it damage the color or consistency of the metal frame? Will it damage the buttons (Power, Volum, Bixby)?
Secondly, which tool should do the job reaching such tiny gap while at the same time not scratching the screen or the metal frame? Metal Blade? Plastic Blade? Wire? Some other tool?
Click to expand...
Click to collapse
I had the same issue with mine and all I used is the film that you remove from the Glass protector before application.. cut off small squares and I ran that in the tiny gaps but making sure you don't go too deep.. Patience and time is must..
I do have a question though.. What is the best thing to use if I wanted to remove my protector off, clean the cured adhesive and use the 2nd bottle to reapply??
View attachment 4603992
View attachment 4604003This has lived in a case since day one, I work in an office wtf is the rear made from
I've heard that sometimes small bits of sand (or whatever) can get trapped between a phone case and the phone.
bonerp said:
View attachment 4603992
View attachment 4604003This has lived in a case since day one, I work in an office wtf is the rear made from
Click to expand...
Click to collapse
It's made from butter. Joking aside I remember my note 8 when brand new after day two in a case there was a scratch on the back. Ever since that moment , I've used back film protection as well. It just takes a grand of sand to get lodged inside the case to do a lot of damage.
Also what case ? Some cases are better at trapping the grain of sand and preventing it from moving around than others.
Sent from my SM-N960U1 using Tapatalk
Limeybastard said:
It's made from butter. Joking aside I remember my note 8 when brand new after day two in a case there was a scratch on the back. Ever since that moment , I've used back film protection as well. It just takes a grand of sand to get lodged inside the case to do a lot of damage.
Also what case ? Some cases are better at trapping the grain of sand and preventing it from moving around than others.
Sent from my SM-N960U1 using Tapatalk
Click to expand...
Click to collapse
Spigen la manon.
Made of chocolate.
Yeaup small particles can get sandwiched in the case but it seems odd it would be a long scratch if that was the case.
That's why I either do a clear slick wraps or throw on a debrand.
Phones in cases got those a lot easier than naked. Small debriefs enters the case and starts to scratch the sides/back.
Yeah.. Tell me a phone with glass back and a Case on not getting hairline scratches and dotted "spots" on the back !
Being cautious and have been using plastic protectors there since "glass era".
This is why I purchased a case AND DBrand skin for it. All my phones have gotten scratches on the back from dust and grit getting under the case. Trying real hard to keep this one pristine.
That is why I like Samsung OEM cases for the N9. They line the inside of them with material to decrease the chance of these blunders.
bonerp said:
This has lived in a case since day one, I work in an office wtf is the rear made from
Click to expand...
Click to collapse
Something softer than sand it appears.
my note 8 still is scratch free after riding in a UAG case since launch...hoping to get my Note 9 tomorrow or Thursday...just couldn't bring myself to pay 1250 at launch this year after having new Note every year since GN3 on launch day or before with early shipping. Managed to acquire one on swappa for $850(512GB) so it was worth the wait if it's as described
are these glass backs or some poly type plastic? I wonder whether a session with poly watch might help.
bonerp said:
are these glass backs or some poly type plastic? I wonder whether a session with poly watch might help.
Click to expand...
Click to collapse
Glass back. A good was or oleophobic coating might help with some scratches. Definitely not going to help with sand getting in between case and phone though.
bonerp said:
are these glass backs or some poly type plastic? I wonder whether a session with poly watch might help.
Click to expand...
Click to collapse
Hey, reviving an old thread. Did you find any fix? I have not one, but 2 medium and 1 small scratch on my back and I used Displex but didnt change anything (I mean really nothing). Any other suggestion? I would try a magic pen for cars and then apply dbrand skin. I so ****ing hate how weak is the rear glass
azZA_09 said:
Hey, reviving an old thread. Did you find any fix? I have not one, but 2 medium and 1 small scratch on my back and I used Displex but didnt change anything (I mean really nothing). Any other suggestion? I would try a magic pen for cars and then apply dbrand skin. I so ****ing hate how weak is the rear glass
Click to expand...
Click to collapse
There is no fix. Just prevention. All mentioned above.
Sent from my SM-N960U1 using Tapatalk
Limeybastard said:
There is no fix. Just prevention. All mentioned above.
Click to expand...
Click to collapse
Yea, but I had a HTC 10 before, full metal. Never had a rear glass
Sand/dust will always cause scratches on glass. Only way around it is to put a protective skin on the back. Even if it's a tight case, the device will shift and particles can still move around between device and case.
There's probably no way to fix the scratches once their occur because its happening to the glass, not a layer of protection onto of it like paint is on a car. No matter what clear liquid you put on their to dry, it will always show the scratch/crack as light will refract at multiple angles, causing you to see the scratches/crack.
Also the finger print sensor is very eazy to scratch
Ironically when I got my Note 9 I left the plastic attached to the back of the phone from the factory before I installed a case on it . I learned this from my S8+ which also got similar scratches . My thought process is this , I was putting it in a case anyways and while the case itself should protect it . I decided to leave the plastic backing on the phone in place anyways . Not like I was going to see it under the case anyways .