[Guide] Comprehensive T380 (Tab A 2017 8.0) root guide - Samsung Galaxy Tab A series Guides, News, & Discus

Disclaimer: Do it with your own risk. Knox will be tripped!!!
DO NOT REBOOT THE UNIT AFTER ROOTED FOR AT LEAST 7 DAYS UNTIL OEM UNLOCK OPTION SHOWS UP AGAIN!!! Failure to do it will result losing root and you have to wait 7 days.
Preparation:
1. Install Samsung Smart Switch on host PC and unit to backup data and install required driver
2. ADB should be installed
3. Download Magisk and copy onto memory card.
4. Download Odin
5. Download TWRP from @ashyx and locate it to where Odin can be found. https://forum.xda-developers.com/ga...t-samsung-tab-8-0-2017-root-tutorial-t3730905
6. (Recommended) Download full ROM from sammobile.com just in case you need it with Odin. Model, version, and CSC should match your model.
7. There's a 7 day waiting to have OEM Unlock option shows up. This is a required step, and you have to wait 7 days after factory reset.
Operation:
1. Backup data with Smart Switch to both memory card and your host PC
2. Enter Download Mode
Use adb command
Code:
adb reboot bootloader
or Turn the unit off, and press and hold Home+Volume Down+Power
3. Make sure Auto Reboot disabled on Odin
4. Flash TWRP on AP slot.
5. Enter TWRP
You have to press and hold Volume Down+Power to reset, and as soon as the screen goes blank, press and hold Volume Up+Power. If you failed to do it, let the tablet boots normally and turn it off. After it's turned off, press and hold Home+Volume Up+Power to enter TWRP.
6. Format Data
This is a critical step to make sure root installed properly. On TWRP main screen, go to Wipe and Format Data and answer yes. After formatting, go back to main screen and choose reboot and reboot recovery
7. Install root of your choice
When you're back to TWRP, you can install root of your choice. Make sure it's copied onto memory card so you can install. You should see no error (no red line). Wipe cache if you want.
8. Reboot to system
It may take 10-15 minutes, and you will see Samsung flashes. Don't worry. You will see the initial setup screen and finish it.
9. Check root
For Magisk, you should see two checks. Make sure you install Safety Net check to complete.
10. Restore data
Congratulations! Your T380 is successfully rooted.
(Optional but recommended)
After rooted, use your root file explorer and do the following:
1. Edit build.prop
Change ro.security.vaultkeeper.feature=1 from 1 to 0
2. Remove RLC folder
Delete /system/priv-app/Rlc

There isn't any way of bypassing OEM unlock? I have this tab new and I want to be rooted now....
---------- Post added at 11:08 PM ---------- Previous post was at 11:04 PM ----------
I had a sm-t350 then I broke the charger port in the device so I updated to the sm-t380 and the OEM unlock thing I couldn't figure out why Odin and Heimdall wouldn't let me use twrp

no OEM Unlock option after 8 days
My tab has been on for 8 days and the OEM Unlock option hasn't shown up
Edit: after turning developer settings off and on again it showed up

DessertArbiter said:
My tab has been on for 8 days and the OEM Unlock option hasn't shown up
Edit: after turning developer settings off and on again it showed up
Click to expand...
Click to collapse
it did the same to me, I found another way of causing it to come up and immediatly (providing the 7 days have passed).
I tried setting time and date forward and that did nothing at all as if the tablet knew it was being tricked.
i did that on the 4th day as I too was impatient, set it forward 1 month and nothing.
then after 8 days it still hadn't shown up, so i connected to wifi and then went to settings, general management, date and time, flipped the automatic date and time to off and then back on again, rebooted the device (wifi still on when i rebooted) and then went to settings, developer options and it was visible.
hasn't helped me though, i still can't get my tablet to take TWRP.

Buying this tablet for someone as a gift but planned to root it first. Anything you guys would recommend as must have after root? And what would you recommend removing straight away?

nolajohnny said:
Buying this tablet for someone as a gift but planned to root it first. Anything you guys would recommend as must have after root? And what would you recommend removing straight away?
Click to expand...
Click to collapse
Titanium Backup Pro, RootExplorer, Rootbooter, about all you need for rooted tools and utilities really.
root booter is optional but it saves the finger gymnastics getting into TWRP.
I rooted one of these had it rooted for over a week and lost root on it, be very careful with this model, it can be very touchy, nice tablet though really.

For Oreo you need a custom kernel for full root because of Samsung Defex

Worked great!
This worked perfectly! Thank you so much. Wish it was as easy to root my S9+.

CSC?
Corwinder said:
This worked perfectly! Thank you so much. Wish it was as easy to root my S9+.
Click to expand...
Click to collapse
hello -
when you rooted, did you download firmware and if so how did you determine CSC?

mingkee said:
Disclaimer: Do it with your own risk. Knox will be tripped!!!
DO NOT REBOOT THE UNIT AFTER ROOTED FOR AT LEAST 7 DAYS UNTIL OEM UNLOCK OPTION SHOWS UP AGAIN!!! Failure to do it will result losing root and you have to wait 7 days.
Preparation:
1. Install Samsung Smart Switch on host PC and unit to backup data and install required driver
2. ADB should be installed
3. Download Magisk and copy onto memory card.
4. Download Odin
5. Download TWRP from @ashyx and locate it to where Odin can be found. https://forum.xda-developers.com/ga...t-samsung-tab-8-0-2017-root-tutorial-t3730905
6. (Recommended) Download full ROM from sammobile.com just in case you need it with Odin. Model, version, and CSC should match your model.
7. There's a 7 day waiting to have OEM Unlock option shows up. This is a required step, and you have to wait 7 days after factory reset.
Operation:
1. Backup data with Smart Switch to both memory card and your host PC
2. Enter Download Mode
Use adb command
Code:
adb reboot bootloader
or Turn the unit off, and press and hold Home+Volume Down+Power
3. Make sure Auto Reboot disabled on Odin
4. Flash TWRP on AP slot.
5. Enter TWRP
You have to press and hold Volume Down+Power to reset, and as soon as the screen goes blank, press and hold Volume Up+Power. If you failed to do it, let the tablet boots normally and turn it off. After it's turned off, press and hold Home+Volume Up+Power to enter TWRP.
6. Format Data
This is a critical step to make sure root installed properly. On TWRP main screen, go to Wipe and Format Data and answer yes. After formatting, go back to main screen and choose reboot and reboot recovery
7. Install root of your choice
When you're back to TWRP, you can install root of your choice. Make sure it's copied onto memory card so you can install. You should see no error (no red line). Wipe cache if you want.
8. Reboot to system
It may take 10-15 minutes, and you will see Samsung flashes. Don't worry. You will see the initial setup screen and finish it.
9. Check root
For Magisk, you should see two checks. Make sure you install Safety Net check to complete.
10. Restore data
Congratulations! Your T380 is successfully rooted.
(Optional but recommended)
After rooted, use your root file explorer and do the following:
1. Edit build.prop
Change ro.security.vaultkeeper.feature=1 from 1 to 0
2. Remove RLC folder
Delete /system/priv-app/Rlc
Click to expand...
Click to collapse
Thank you for posting this guide. I followed all steps exactly as written; installed magisk; obtained root. Problem is that when in TWRP I cannot mount data. External SD mounts fine, but internal storage reads 0MB. My device is T380 (2017) Oreo 8.1 . Any suggestions? Thanks.

jurisquo said:
Thank you for posting this guide. I followed all steps exactly as written; installed magisk; obtained root. Problem is that when in TWRP I cannot mount data. External SD mounts fine, but internal storage reads 0MB. My device is T380 (2017) Oreo 8.1 . Any suggestions? Thanks.
Click to expand...
Click to collapse
That's OK
Just let it be until you have done optional step to prevent the "lockup"

mingkee said:
That's OK
Just let it be until you have done optional step to prevent the "lockup"
Click to expand...
Click to collapse
I have the same issue and when I did try to do the optional recommended steps I couldn't find either step in build.prop or system folder.

Magisk Install Error
Doing just as you say, I got TWRP to take just fine but Magisk Manager reports that no Root is installed. The only red line I saw while installing Magisk simply said 'E:' and that's all... Any ideas out there why I'm getting that error?

Austcool said:
There isn't any way of bypassing OEM unlock? I have this tab new and I want to be rooted now....
---------- Post added at 11:08 PM ---------- Previous post was at 11:04 PM ----------
I had a sm-t350 then I broke the charger port in the device so I updated to the sm-t380 and the OEM unlock thing I couldn't figure out why Odin and Heimdall wouldn't let me use twrp
Click to expand...
Click to collapse
I have used a method where you remove the sim card (If your device has one) factory reset the device, then set it up without a sim card or connecting to the internet, then turn on developer options, then conntent to wifi or insternet a wrking sim card, then restart, than the opiton should be there

Magisk is not installed in Magisk Manager after flash with TWRP
hello, I've followed your instructions on how to root and everything seems to be fine and dandy at first, redlines during Magisk installation with TWRP and so on, exactly like your instructions. however after I finished flashing Magisk for root, I boot up my tab and when I want to check if my Magisk is flashed or not using Magisk Manager, it said that my Magisk wasn't installed/flashed? so then I checked with root checker to see if I have root access or not, and turns out I still don't have the root access/root is not installed, even though I clearly just flash magisk into my tab using twrp.
I've been searching for an entire day to find solution online but to no avail whatsoever.... and now I have a bad headache trying to figure out what iv'e been doing wrong during the flash process... yes I have OEM unlocked, yes I have USB Debugging checked during twrp flash using odin, yes I format under wipe option in twrp before flash Magisk. please help....

anyone know how to boot into twrp on the actual sm-t380?

DaricDarkFox said:
anyone know how to boot into twrp on the actual sm-t380?
Click to expand...
Click to collapse
For posterity if no longer for DaricDarkFox:
- Boot to TWRP from power-off using Power and Vol+ (Download Mode is Power and Vol-, TWRP is Power and Vol+)
- Boot from a running system by selecting Restart and then quickly pressing and holding Vol+ (nothing else, just Vol+)
- Boot to TWRP from Download Mode by pressing Power and Vol- (as usual to exit Download Mode) and when screen goes blank, quickly release Vol- (but still holding Power) and press and hold Vol+
All of these methods consistently work for me. Most guidance for the T380 says to also press and hold the Home button, but (again for me at least) the Home button is not needed at all.

Related

[TUT] How to root and un-root GT-I9305 on KitKat 4.4.4.

I'M NOT RESPONSIBLE IF YOUR PHONE GOT BRICKED, DO THIS AT YOUR OWN RISK!
ROOTING (CUSTOM RECOVERY + SUPERSU)​
MAKE SURE YOUR PHONE’S 80% CHARGE OR ABOVE!!!
1) Download Odin.
LINK: https://www.dropbox.com/s/fivpr9btf6667hr/Odin 3.07.rar?dl=0
Download “philz_touch_6.26.6-i9305.tar”
LINK: http://goo.im/devs/mskip/recovery/samsung_galaxy_s3/philz_touch_6.26.6-i9305.tar.md5/
2) Unzip Odin to your desktop.
Copy the “philz_touch_6.26.6-i9305.tar” to the same directory.
3) Make sure your phone is in DOWNLOAD MODE.
Power OFF your phone if you haven't done so.
Press Volume Down + Home Button + Power Button.
You will see a screen saying “Warning!”
Just ignore what it says and PRESS the Volume Up button.
4) Now, connect the phone to your Windows computer/laptop.
Connect the USB cable to your phone first then to your computer.
Let it detect your phone.
5) If Kies is running on your pc shut it down.
6) Open the Odin application.
7) In the Message Box (located at the bottom left corner of Odin), you should see "Added!!" there.
8) Choose PDA button and select the "philz_touch_6.26.6-i9305.tar".
9) Now, click on START. Your phone will be flashed and reboot when it is finished.
10) After rebooting, copy “UPDATE-SuperSU-v2.02” to your SD Card.
LINK: http://download.chainfire.eu/452/SuperSU/UPDATE-SuperSU-v2.02.zip
11) Power it off again.
12) Put the phone in recovery mode.
Hold down Power, Volume Up and Home when the device is turned off and unplugged and release once you see the Samsung logo.
13) After that you can flash the “UPDATE-SuperSU-v2.02” to be ROOTED to any firmware.
UN-ROOTING USING PC ODIN​
MAKE SURE YOUR PHONE’S 80% CHARGE OR ABOVE!!!
1) Make sure your phone is in DOWNLOAD MODE.
Power OFF your phone if you haven't done so.
Press Volume Down + Home Button + Power Button.
You will see a screen saying “Warning!”
Just ignore what it says and PRESS the Volume Up button.
2) Now, connect the phone to your Windows computer/laptop.
Connect the USB cable to your phone first then to your computer.
Let it detect your phone.
3) Extract both files (Odin & Stock Rom) to your Desktop.
Double-click on the Odin executable file and it’ll launch.
4) In the Odin, click on PDA tab and select the Stock Firmware file you extracted to your Desktop.
5) Make sure only Auto Reboot and F. Reset Time boxes are checked in the Odin.
6) Click on Start button in the Odin and leave the rest of the work on the tool.
Your device should reboot once flashing’s done.
7) You have successfully un-rooted your S3!
USING MOBILE ODIN​
1) Ensure you’re having root access using “Root Checker”.
2) Copy the Stock Firmware file to your SD Card.
3) Install Mobile Odin APK and open it.
4) Choose “Open File…”
5) Navigate to where you put the Stock Firmware and choose it.
6) Now scroll down till you see “Ever Root” and uncheck it.
7) Now tap “Flash Firmware”, you’re phone will restart and start flashing.
8) After flashing is done it’ll reboot.
9) You have successfully un-rooted your S3!
Credit goes to @SeyMedia for original aid, I just made this into a tutorial. Good Luck!:good:
root/recovery won't work that way for 4.4
as soon as you let the phone reboot into system after flashing custom recovery, it will get overwritten by original one; so after you turn the phone off and reboot manually then, don't be surprised to see stock recovery
After flashing custom recovery don't turn the phone on. Just return with 3combo to recovery and flash su. This is how worked for me
Regarding the rooting process:
- just untick F. Reset Time in Odin when you flash philz_touch_6.26.6-i9305.tar;
- when flashing is done, disconnect phone from pc and pull up the battery for a few seconds;
- put back the battery;
- enter in recovery mode (you will enter in Philz Touch);
- flash UPDATE-SuperSU-v2.02.
This will do the trick!
SeyMedia said:
Regarding the rooting process:
- flash UPDATE-SuperSU-v2.02.
This will do the trick!
Click to expand...
Click to collapse
I downloaed SuperSU 2.02 two times from official site, but it didn't want to flash...
I think it is corrputed. After that i downloaded 1.96 and it worked.
yozo
yozotheboss said:
I downloaed SuperSU 2.02 two times from official site, but it didn't want to flash...
I think it is corrputed. After that i downloaded 1.96 and it worked.
yozo
Click to expand...
Click to collapse
I used this downloaded from official site a few months ago and it worked.
Why you use “philz_touch_6.26.6-i9305.tar” and not more new "philz_touch_6.48.4-i9305.tar"?
psychok9 said:
Why you use “philz_touch_6.26.6-i9305.tar” and not more new "philz_touch_6.48.4-i9305.tar"?
Click to expand...
Click to collapse
I used this and i didn't checked if is a new version when i talked with Yousef Khashaba.
Do you have to use a custom recovery to root kk 4.4.4 or can I just use CF-auto root and triangle away with the stock recovery?
going to test .. any one know chainfire cf-root works for i9305 or not ?
afraaa said:
going to test .. any one know chainfire cf-root works for i9305 or not ?
Click to expand...
Click to collapse
Yes it works pefectly
Raistlin1158 said:
Yes it works pefectly
Click to expand...
Click to collapse
i mean .. chainfire has i9305N for kitkat 4.4.4 ... we have i9305 no N no T ... just 9305 .. can i use 9305N for root ? they are sharing same CPU . different is software build number .. what do u suggest man .. appreciate your answer and w8 for your answer
---------- Post added at 10:44 PM ---------- Previous post was at 10:44 PM ----------
PS : sry thanks button reach limit will give it tomorow . do u suggest i use chainfire or this method ?
i guess above question answer is no ...
about this OPS method : confirming root on GT-i9305 model running kitkat 4.4.4 ?

TWRP Galaxy J1 2016 Sm-J120H Spreadtrum SC8830 Really Working (Brazilian devices)

(DISCONTINNUED
This TWRP is only for Speadtrum 3G!!!!
Hi folks!
Finally we have a twrp for your Sm-j120H Spreatrum that works! Here's the link:
Root SM-J120H working.rar
http://www20.zippyshare.com/v/XmD4XuEW/file.html
If you want to test (do it for your own risk)!
STEPS:
1 - Unzip file on your computer;
2 - Open Odin folder and copy the supersu zip file to your internal memory (without unzip it);
3 - Open Odin (double click on blue icon);
4 - Click on "AP" icon and select the twrp tar file on Odin folder (j1 (6).tar);
5 - Turn on "Unlock OEM" and "USB Debugging" on Delevoper Options (Actvating Delevoper Options: seven clicks on Build Number - Software Info);
6 - Turn off your phone and turn on again holding Volume Down + Home Button + Power Button (Download Mode). When a screen with some texts appears, release all buttons and press Volume Up again to activate the Download Mode;
7 - After this, connect your phone to your computer and click Start on Odin. Wait until your device restarts;
8 - Disconnect your phone to your computer and turn it off. Turn it on holding Volume Up + Home Button + Power Button (Recovery Mode). When your phone vibrates and appears J1 6 logo, release all buttons. If worked, TWRp will starts;
9 - Select the language, click on Read Only and the TWRP starts. After this, click on Install and search The Supersu zip you copied. Click on it and drag the flash file. Wait finish it. Restart the system. Done!
Credits: Aldous Cariño (Galaxy J1 Edition Phillipines Facebook Group - (https://www.facebook.com/groups/SamsungGalaxyJ12016EditionGroupPhilippines/)
IMPORTANT!!!!!!
This twrp was tested and worked on brazilian devices. Others had some problems. Test it and comment your feedback here!
If you are a developer and interests to work on this file, but doesn't have the device, i'll be glad to help being your beta tester!!!!
If you need the stock rom, download it from this site: https://samsung-firmware.org/model/SM-J120H/
Thanks!
I tried this on a SM-J120M from Colombia.
Recocvery flashed OK, phone rebooted.
Turned it off, tried to enter recovery, android robot appears "installing system update" or something like that.
After a few seconds, standard recovery appears and not TWRP.
So I figured that the stock rom somehow replaces the custom recovery at first boot.
Flashed again but after Odin finished, I pulled the battery at once.
Tried again to enter recovery, this time a red text above the J1 logo shows "Recovery is not seandroid enforcing"
Pulled the battery again and turned on, phone booted normally, but twrp recovery was again replaced with standard recovery.
I'm on the latest firmware and this phone until now can not be rooted and no custom recovery seems to be available.
Somehow "knox" was set to 1 in the process, meaning warranty void.
Cheers.
Well, this has been tackled finally
Key issue was the right TWRP recovery.
Someone on Youtube posted the instructions and files titled: RECOVERY TWRP PARA SAMSUNG J1 2016 (TODAS LAS VERSIONES)
This time the TWRP recovery did work, after that I flashed the SuperSu from TWRP and all was finished.
Next I'll be looking for a custom rom, but so far very happy with the results.
Cheers.
escorpiompom said:
Well, this has been tackled finally
Key issue was the right TWRP recovery.
Someone on Youtube posted the instructions and files titled: RECOVERY TWRP PARA SAMSUNG J1 2016 (TODAS LAS VERSIONES)
This time the TWRP recovery did work, after that I flashed the SuperSu from TWRP and all was finished.
Next I'll be looking for a custom rom, but so far very happy with the results.
Cheers.
Click to expand...
Click to collapse
Hello,
Could I have a link to the files that work for the J120M? I have the same phone and I think I found what you're talking about but I have the same issue with the stock recovery showing up instead.
Thanks!
EDIT: Actually, do I need to use TWRP? Can't I just "install update from external storage" with the stock bootloader?
Sure, I didn't post the link because it may not be allowed on this board (for newbies like me).
If you just put that title in Youtube it shows as the first result.
Anyway, here is the direct link for all the files:
Code:
https://www.datafilehost.com/d/296cd14c
Disable the download manager that is checked by default.
Use odin to flash TWRP, disable auto reboot and after flashing enter recovery at once with vol up+home+power buttons.
You may get a warning in red about recovery not enforcing blaba, just wait until TWRP shows and release the buttons.
It's not possible to flash SuperSU from stock recovery, you need a custom recovery like TWRP.
I couldn't find CWM for this phone, but anyway I like TWRP more.
Cheers.
escorpiompom said:
Sure, I didn't post the link because it may not be allowed on this board (for newbies like me).
If you just put that title in Youtube it shows as the first result.
Anyway, here is the direct link for all the files:
Code:
Disable the download manager that is checked by default.
Use odin to flash TWRP, disable auto reboot and after flashing enter recovery at once with vol up+home+power buttons.
You may get a warning in red about recovery not enforcing blaba, just wait until TWRP shows and release the buttons.
It's not possible to flash SuperSU from stock recovery, you need a custom recovery like TWRP.
I couldn't find CWM for this phone, but anyway I like TWRP more.
Cheers.
Click to expand...
Click to collapse
Ahh, thanks! As it turns out I did find the correct link, but the trick was to immediately enter into recovery mode after flashing without letting the phone fully boot first. Got my phone rooted now, thanks a bunch!
This method workin on 100%/ Thanks!
amebablues said:
Hi folks!
Finally we have a twrp for your Sm-j120H Spreatrum that works! Here's the link:
Root SM-J120H working.rar
http://www20.zippyshare.com/v/XmD4XuEW/file.html
If you want to test (do it for your own risk)!
STEPS:
1 - Unzip file on your computer;
2 - Open Odin folder and copy the supersu zip file to your internal memory (without unzip it);
3 - Open Odin (double click on blue icon);
4 - Click on "AP" icon and select the twrp tar file on Odin folder (j1 (6).tar);
5 - Turn on "Unlock OEM" and "USB Debugging" on Delevoper Options (Actvating Delevoper Options: seven clicks on Build Number - Software Info);
6 - Turn off your phone and turn on again holding Volume Down + Home Button + Power Button (Download Mode). When a screen with some texts appears, release all buttons and press Volume Up again to activate the Download Mode;
7 - After this, connect your phone to your computer and click Start on Odin. Wait until your device restarts;
8 - Disconnect your phone to your computer and turn it off. Turn it on holding Volume Up + Home Button + Power Button (Recovery Mode). When your phone vibrates and appears J1 6 logo, release all buttons. If worked, TWRp will starts;
9 - Select the language, click on Read Only and the TWRP starts. After this, click on Install and search The Supersu zip you copied. Click on it and drag the flash file. Wait finish it. Restart the system. Done!
Credits: Aldous Cariño (Galaxy J1 Edition Phillipines Facebook Group - (https://www.facebook.com/groups/SamsungGalaxyJ12016EditionGroupPhilippines/)
IMPORTANT!!!!!!
This twrp was tested and worked on brazilian devices. Others had some problems. Test it and comment your feedback here!
If you are a developer and interests to work on this file, but doesn't have the device, i'll be glad to help being your beta tester!!!!
If you need the stock rom, download it from this site: https://samsung-firmware.org/model/SM-J120H/
Thanks!
Click to expand...
Click to collapse
hi bro
not working ext sd card or otg . how to fix it ? iwant install patch file my phone is locked by user code and i cant copy file to internal storag
thank you
anitamobile said:
hi bro
not working ext sd card or otg . how to fix it ? iwant install patch file my phone is locked by user code and i cant copy file to internal storag
thank you
Click to expand...
Click to collapse
This file is for Spreadtrum 3G devices. OTG not working at all. FOr ext card, try to wipe data and cache after install and reboot.
tried it on my SM-J120G, but failed .. all steps completed but when i started the phone in recovery mod, it got stuck at j1 2016 logo and a message in red fonts saying ''RECOVERY IS NOT SEANDROID ENFORCING''. After i just tried to switch off and on, but the screen dosent respond. After holding all physical button, vol up-dn, power and home, it got restarted in normal mode.
device tree
please give me device tree of this device .. please
Does it works in sm-j120G??
anitamobile said:
hi bro
not working ext sd card or otg . how to fix it ? iwant install patch file my phone is locked by user code and i cant copy file to internal storag
thank you
Click to expand...
Click to collapse
The problem has been resolved
new recovery twrp :fingers-crossed:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
---------- Post added at 12:11 AM ---------- Previous post was at 12:06 AM ----------
amebablues said:
This file is for Spreadtrum 3G devices. OTG not working at all. FOr ext card, try to wipe data and cache after install and reboot.
Click to expand...
Click to collapse
The problem has been resolved :good:
new TWRP :highfive:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
Project Discotinnued
Sorry taking too long to answer...I'm not using this device anymore. Maybe this link help you: https://github.com/joenka/android_device_j120h
Best regards
shugash said:
Does it works in sm-j120G??
Click to expand...
Click to collapse
Not testing. If you waana try, do it your risk.
syria-droid said:
The problem has been resolved
new recovery twrp :fingers-crossed:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
---------- Post added at 12:11 AM ---------- Previous post was at 12:06 AM ----------
The problem has been resolved :good:
new TWRP :highfive:
https://forum.xda-developers.com/android/development/recovery-twrp-j120h-supports-otg-t3562136
Click to expand...
Click to collapse
Ok. But your device is Speadtrum 3G? This twrp is for this model.
amebablues said:
Ok. But your device is Speadtrum 3G? This twrp is for this model.
Click to expand...
Click to collapse
I know
the problem Present in all phones model (j120h)
Rooted j120g
Bro I have rooted my j120g
Want to know how to root contact me bro
[email protected] or fb id skrillex cario
Hai is it possible to flash stock 120g firmware on 120h ? Please reply
Help me to Root my Samsung Galaxy J1 (2016) SM-J120H
Sir I really need your help. What is the first thing to do before going into Rooting method? Do I need to backup any Files or what? Thnak you. Guide me please. Thank You

[GUIDE]Comprehensive T510 root guide

Warning:
Proceed with your own risk. I hold no responsibility if something goes wrong and you get killed.
Warranty void
KNOX tripped and some security feature won't be available
This guide based on @topjohnwu Magisk for Samsung. However, T510 is a bit different because it doesn't have Bixby button.
https://topjohnwu.github.io/Magisk/samsung
You need the latest Odin (I use 3.13). 3.12 or older won't work
***** NOTICE *****
Auto reboot must be disabled.
Download ROM matches your build number especially the last three characters. Unzip and only use AP and copy it to your tablet
Download ***special*** version Magisk Manager to your tablet and install it. "Install" Magisk using patch boot with AP file, and copy magisk_patched.tar to your host PC
https://raw.githubusercontent.com/topjohnwu/magisk_files/master/canary_builds/app-release.apk
Do not use normal Magisk to patch AP because it won't work
Bootloader Unlocked (read my guide)
Do not restore yet until this process is done.
STEPS:
1. Download your version of ROM. Make sure it matches your device Build Number
2. Unzip the ROM and copy AP to your tablet. Install Magisk Manager downloaded from link above. Normal Magisk Manager won't work.
3. Patch AP with Magisk Manager. The output file is "magisk_patched.tar". Copy the output file to your host computer.
4. Open Odin. Make sure Auto Reboot is disabled (unchecked)
5. Turn your tablet off. Press and hold Volume up and down buttons and connect your tablet to host computer. Press Volume up again to enter Download Mode.
6. Odin should show "Added". Locate your "magisk_patched.tar" and open as AP (it's AP after all). You don't have to flash others.
7. Wipe your tablet.
Disconnect your tablet.
Press and hold Power and Volume down.
As soon as the screen goes dark, immediately press and hold Power and Volume up until recovery screen appears.
Choose Factory Reset and press Power once, and confirm.
Reboot System Now
8. As soon as the screen turns dark, press and hold Power and Volume up buttons before screen shows bootloader warning. It will reboot again like brand new unit.
9. Do initial setup. Copy the Magisk Manager to your tablet and install if you don't see it
10. Setup internet connection and Magisk Manager will do some process, and it will reboot after it's done. You don't have to do button combo at this time.
11. Open Magisk Manager again to add other function including hide.
Your tablet should be rooted. However, here is something you should know.
Press Power button only: System with Magisk
[*]Press and hold Power and Volume up buttons before the screen shows bootloader warning and release: System with Magisk
Press and hold Power and Volume up buttons all the way: Stock recovery
That's it. Root is done.
***** IMPORTANT *****
If you want to do manual update, make sure you do steps 1-6 again. You don't have to wipe your tablet however.
Update: it appears "normal" Magisk (19.3) and Magisk Manager can simplify the entire rooting process.
Special instructions for Samsung is gone now.
Moreover, it appears normal boot can enter rooted system without button combo
mingkee said:
However, here is something you should know.
Press Power button only: System with no Magisk
Press and hold Power and Volume up buttons before the screen shows bootloader warning and release: System with Magisk
Press and hold Power and Volume up buttons all the way: Stock recovery
That's it. Root is done.
Click to expand...
Click to collapse
I must not be understanding something, as no matter how I press Power and Volume Up, I end-up in recovery. Otherwise it boots without magisk installed.
If I release buttons when I see the Samsung logo, before the warning, I can then press volume up to continue with boot, and it opens recovery.
If I release buttons after I see the warning, the warning goes away in a flash and I still end-up in recovery.
If I release the buttons as soon as I see the Samsung logo, same thing.
Any suggestions?
I did all the steps again, strangely Magisk gave me a different patched.tar file.
Flashed the patched, but I noticed in Odin:
<ID:0/008> recovery.img
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I get a red message saying only official release binaries... The tablet is unlocked though... I must be missing something.
EDIT:
Now the tablet says an error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software. Can't even turn it off!
Smart Switch says 'Unsupported device' and device does not appear in the list for emergency recovery. Tablet appears soft-bricked
Finally Odin managed to flash it, after failing at first. Flashing stock now. Will start over.
It appears the latest Magisk and Manager simplified everything.
The latest Magisk (19.3) is "normal" version, so you may no longer need "canary". Moreover, special instructions for Samsung disappeared (click the link on the first post and it doesn't work).
I also noticed normal boot (just press power button with no combo) and boot into "root mode"
mingkee said:
It appears the latest Magisk and Manager simplified everything.
The latest Magisk (19.3) is "normal" version, so you may no longer need "canary". Moreover, special instructions for Samsung disappeared (click the link on the first post and it doesn't work).
I also noticed normal boot (just press power button with no combo) and boot into "root mode"
Click to expand...
Click to collapse
I followed the original guide and using the button combo to boot with Magisk. How do I move to normal boot? Magisk installed version is 19.4-c, and I just received version 7.3.0 of the manager. Should I simply (re-)install Magisk 19.4-c to get normal boot?
3c said:
I followed the original guide and using the button combo to boot with Magisk. How do I move to normal boot? Magisk installed version is 19.4-c, and I just received version 7.3.0 of the manager. Should I simply (re-)install Magisk 19.4-c to get normal boot?
Click to expand...
Click to collapse
I will show you a screen cap later on because I don't carry it to work.
I used the "canary" build Manager and the root.zip
Now the root.zip is normal while Manager build number is still different.
As I mentioned on the edited post, the special instructions is gone, so it's possible topjohn has figured out solution for Samsung and integrated.
Yes, I boot it "normal" way and root is 100%
Noob Question
Hello and thanks for that guide!
There is (at least for now) one question:
Where do I get the stock ROM from?
mingkee said:
Warning:
STEPS:
1. Download your version of ROM. Make sure it matches your device Build Number
Click to expand...
Click to collapse
LeonardHofstadter said:
Hello and thanks for that guide!
There is (at least for now) one question:
Where do I get the stock ROM from?
Click to expand...
Click to collapse
You can find them on sammobile or samfrew
Thanks for this guide but I think I didn't do something right.
----------------
Reboot System Now
8. As soon as the screen turns dark, press and hold Power and Volume up buttons before screen shows bootloader warning. It will reboot again like brand new unit.
----------------
At this part, just after the factory reset, I reboot system and then I press Power and Vol+, but it goes again to Recovery. It never reboots like "brand new unit". It will always show the warning at start. Perhaps I misunderstood this part somehow.
Hantoniorl said:
Thanks for this guide but I think I didn't do something right.
----------------
Reboot System Now
8. As soon as the screen turns dark, press and hold Power and Volume up buttons before screen shows bootloader warning. It will reboot again like brand new unit.
----------------
At this part, just after the factory reset, I reboot system and then I press Power and Vol+, but it goes again to Recovery. It never reboots like "brand new unit". It will always show the warning at start. Perhaps I misunderstood this part somehow.
Click to expand...
Click to collapse
When you press Power and Vol+ the warning will only flash, that's when you need to release the buttons. If you keep pressing it goes in recovery. I had a hard time figuring this out.
3c said:
When you press Power and Vol+ the warning will only flash, that's when you need to release the buttons. If you keep pressing it goes in recovery. I had a hard time figuring this out.
Click to expand...
Click to collapse
Thanks!
I just tried releasing the buttons just afther the "warning flash". Then it showed up again. After initial settings and Magisk installation, again that screen.
I'll try to start from scratch with another T510 and report back as soon as I can. Thanks again.
I'm pretty sure rebooting to recovery with volume up and power is still needed on every boot. The link for Samsung devices has just been moved.
https://topjohnwu.github.io/Magisk/install.html#samsung-system-as-root
Thanks for the guide.
Can someone confirm if i reboot, what do i have to press to keep it in root mode.?
So far the only way I've been able to do it, is to press power and volume up button and release when it flashes.
Root keeps disappearing unless I press combination of buttons.
Is there anyway to keep in root mode without pressing buttons?
test2006au said:
Thanks for the guide.
Can someone confirm if i reboot, what do i have to press to keep it in root mode.?
So far the only way I've been able to do it, is to press power and volume up button and release when it flashes.
Root keeps disappearing unless I press combination of buttons.
Is there anyway to keep in root mode without pressing buttons?
Click to expand...
Click to collapse
I believe this is the only method at the moment.
Thank you very much for the rooting method, after unlocking the bootlader and rooting I have expanded my ram and now my tablet works flawlessly
Has anyone had any luck using Odin on Linux? I'm using JOdin Casual on Linux Mint and it seems like the process hangs while sending the patched image to the tablet, I also tried using my Windows 10 VM, and it seems to just get stuck after hitting start in Odin
Triscuit said:
Has anyone had any luck using Odin on Linux? I'm using JOdin Casual on Linux Mint and it seems like the process hangs while sending the patched image to the tablet, I also tried using my Windows 10 VM, and it seems to just get stuck after hitting start in Odin
Click to expand...
Click to collapse
Sent from my Pixel 2 XL using XDA Labs
Hey there, thank you for your guide!
I had a little problem when flashing with Odin though.
The tablet starts downloading, but when it gets to vbmeta.img, it shows the error "Custom Binary(VBMETA) Blocked by OEM Lock"
Before flashing, I disabled OEM Lock in the Developer Settings, but it did not help.
Any ideas would be greatly appreciated. Thx again!
Triscuit said:
Has anyone had any luck using Odin on Linux? I'm using JOdin Casual on Linux Mint and it seems like the process hangs while sending the patched image to the tablet, I also tried using my Windows 10 VM, and it seems to just get stuck after hitting start in Odin
Click to expand...
Click to collapse
I'm hitting a roadblock here, as well. I haven't tried using JOdin because I've seen discussions stating that you need 1.4.2 of Heimdall to flash these tablets, so I built that from source (JOdin includes 1.4.0). I unlocked the tablet, then patched the firmware with Magisk. Now I'm not sure what to do next.
Heimdall has its own package structure (which I'll read tonight), so it won't flash the AP file like Odin. It looks like it requires individually flashing each segment of the AP archive directly, and I really don't want to do that without some input from someone who can confirm that will work.
I'm acting based on this thread, on [RECOVERY][UNOFFICIAL] TWRP 3.3.1 for 2019 Galaxy Tab A 10.1 [SM-T510] and the Magisk install by patching file instructions.
Do I really need to extract each piece of the TAR per these instructions?
Also, the instructions to install TWRP here don't state that rooting must be done first, but based on the whole workflow, it seems it is required because this process flashes to AP and Magisk uses a stock AP when patching. It seems the work for TWRP would be obliterated by the Magisk root process.
Can anybody clear this up?
Kenaz Rune said:
I'm hitting a roadblock here, as well. I haven't tried using JOdin because I've seen discussions stating that you need 1.4.2 of Heimdall to flash these tablets, so I built that from source (JOdin includes 1.4.0). I unlocked the tablet, then patched the firmware with Magisk. Now I'm not sure what to do next.
Heimdall has its own package structure (which I'll read tonight), so it won't flash the AP file like Odin. It looks like it requires individually flashing each segment of the AP archive directly, and I really don't want to do that without some input from someone who can confirm that will work.
I'm acting based on this thread, on [RECOVERY][UNOFFICIAL] TWRP 3.3.1 for 2019 Galaxy Tab A 10.1 [SM-T510] and the Magisk install by patching file instructions.
Do I really need to extract each piece of the TAR per these instructions?
Also, the instructions to install TWRP here don't state that rooting must be done first, but based on the whole workflow, it seems it is required because this process flashes to AP and Magisk uses a stock AP when patching. It seems the work for TWRP would be obliterated by the Magisk root process.
Can anybody clear this up?
Click to expand...
Click to collapse
I honestly gave up trying to do this whole process on Linux, so I made a virtual machine with windows, made sure all my USB stuff was correct and used the official ODIN, worked like a charm
Sent from my Pixel 2 XL using XDA Labs

Found a way to root with magisk and Odin.

Hi guys while searching the web and the forum to find a way to root our phone I found this guide https://topjohnwu.github.io/Magisk/samsung
you can do it by yourself if you want but I thought to edit it a bit to match our device. all credit goes to original developer I just copied what he did and it worked.
I don't take any responsibility if anything happens to device, brick ect. use the guide with your own risk!
make sure you have updated drivers and a good usb cable, I recommend Smart Switch for pc you can download in the samsung site, it will also install latest drivers and you can back up the phone with it to the pc.
just for your information rooting voids the waranty, trips knox and makes things complicated, but I can't have a phone without root, it reminds me the days with my old nexus 4.
this guide will also factory reset your phone so make sure to back up everything don't forget to back up whatsapp in the app itself.
I'm not a developer maybe there is an easier way to root, this is the only way I found, so if you want to wait until an experienced developer who knows english better then me release another way to root that's fine by me, I wont get upset.
the only downside I see in this kind of root that you can't normally enter the system. I mean that normal reboot and power up will boot your system without magisk, because the root sits on the recovery or something like that. so each time you power off your phone to power it up you need to hold the Volume up + Power button untill you see the bootloader unlocked warning and release, and everything will be working with root. even if you accidently powerd your phone without the way I mentioned you still have root don't panic like I did just turn off the phone and power it up like I mentioned and its all good.
also you can't normally update the phone through the phone settings and to update the phone with odin like I understand you'll need to have a patched version of the AP tar file with magisk, or something bad will happen to the phone, again I am not a developer I don't know the full risks.
so after the warnings and the long intro here is the edited guide:
Unlock the bootloader - this will wipe all your data so make sure to back up before you start anything!
Allow bootloader unlocking in Developer options → OEM unlocking
Power off your device. Volume Up + Volume Down + Power button and plug in your device to a PC to boot into download mode
Long press volume up to unlock the bootloader. This will wipe your data and automatically reboot.
the developer also mentions that sometimes it wont work because something called VaultKeeper. I didn't had that issue just make sure after the system boots after you unlocked the bootloader that the OEM unlocking option exists and grayed out in the developer options.
Instruction
1.Download the firmware for your device.
2.Unzip the firmware and copy the AP tar file to your device. It is normally named as AP_[device_model_sw_ver].tar.md5
3.Install Magisk Manager from the Canary Channel
4.In Magisk Manager: Install → Install → Select and Patch a File
5.Select the AP tar file. Magisk Manager will patch the whole firmware file and store the output to [Internal Storage]/Download/magisk_patched.tar
6.Copy the tar file to your PC, and boot your device to download mode. (Hold all 3 buttons Volume Up+Volume Down+Power Button and connect to PC cable)
I have downloaded the firmware with Samfirm I found it on the forum I'll upload it here. I will also upload the AP file I patched and write the firmware version I took it from. I'll also upload the full firmware for you if you can't find a good mirror online. and also the odin version I used.
the csc i look up is for ILO but I think the csc have multiple regions, you know better I'll upload it anyway maybe it will save time for someone.
7.Flash magisk_patched.tar as AP in ODIN (I flashed the entire firmware because I had some problems flashing without all the files try it the way you want. flash it with normal csc of you choose to flash the whol firmware)
Important: Uncheck “Auto Reboot” in Options!!!!
8.Magisk is now successfully flashed to your device! But there are still several steps before you can properly use the device.
9.We now want to boot into the stock recovery to factory reset our device.
Full data wipe is mandatory! Do not skip this step.
Press Power Button+Volume Up+Volume Down to exit download mode, and as soon as the screen turns off, immediately press Power Button+Volume Up to boot to recovery partition. Just as mentioned in the previous section, since we want to boot into stock recovery, continue pressing the volume up button until you see the stock recovery screen.
10.In the stock recovery menu, use volume buttons to navigate through menus, and the power button to select the option. Select Wipe data/factory reset to wipe the data of the device.
11.This time, we can finally boot to the system with Magisk. Select Reboot system now, and immediately press Power Button+ Volume Up. After seeing the bootloader warning screen, release all buttons so it can boot to the system.
12.The device will automatically reboot for the first time it boots. This is completely normal and done by design.
13.After the device is booted up, do the usual initial setup. The following steps will need internet connection.
14.You shall see Magisk Manager in your app drawer; if not, manually install the APK you downloaded in step 3 and continue to the next step. The app would be a stub and it shall automatically upgrade to the full Magisk Manager when you open it.
15.Magisk Manager will ask to do additional setups. Let it do its job and the app will automatically reboot your device.
16.Baruh Ashem! enjoy magsik!
That's it I think if I forgot something I'm sorry I hope it worked for you! and maybe some real developers start to look at the device and start building costume roms andall the good stuff that comes with it!
meanwhile the files are uploading you can try get them by yourself here are the names of the files I used:
Odin3_v3.13.1_3B_PatcheD
Samfirm
firmware file: SM-A705FN_1_20190412140953_u5ql0uali6_fac
Magisk manager is linked the developer enterd the canary build but I'll also upload 7.1.2.apk version I found on the internet.
ALL CREDIT GOES TO THE ORIGINAL DEVELOPER, AND DEVELOPERS. if you have any question I can help you with my own expirence only.
Here is the download link, use at your own risk. if you are not sure the firmware uploaded is right for your device download yourself with samfirm that i also uploaded.
Download Link - Google Drive
Thanks for your research and this manual! I've been trying your steps for a few hours now, and after a few trial and errors, softbricks and reboots I'm still not able to succeed.
Magisk Manager won't show up in the apps after setup wizard. Installing it manually, it says Magisk is not installed
My phone: A70 from the Netherlands. I used Israel firmware from updato.com (https://updato.com/firmware-archive-select-model?record=440E12D670B911E9BE8CFA163EE8F90B) and your file (which is same size after patching). Unfortunately I can't find Dutch firmware, hence the Israel version.
Anybody else succeeded?
Captain Beretta said:
Thanks for your research and this manual! I've been trying your steps for a few hours now, and after a few trial and errors, softbricks and reboots I'm still not able to succeed.
Magisk Manager won't show up in the apps after setup wizard. Installing it manually, it says Magisk is not installed
My phone: A70 from the Netherlands. I used Israel firmware from updato.com (https://updato.com/firmware-archive-select-model?record=440E12D670B911E9BE8CFA163EE8F90B) and your file (which is same size after patching). Unfortunately I can't find Dutch firmware, hence the Israel version.
Anybody else succeeded?
Click to expand...
Click to collapse
thank you for the feedback!
did you flashed the whole firmware? with BL, patched AP,CP and CSC? on the google drive folder I have to full firmware try to download that.
maybe you do have it installed but you didn't boot corectly. try to turn off your phone then hold volume up+power button and hold them untill you see the galaxy a70 powered by android. and then check magisk! I hope it helped!
Will try and flash complete firmware with all your Drive files tomorrow! Hope it will succeed
Captain Beretta said:
Will try and flash complete firmware with all your Drive files tomorrow! Hope it will succeed
Click to expand...
Click to collapse
I wait for your success, because I'm trying to decide to buy or not this device (root is very important to me)
infearno said:
I wait for your success, because I'm trying to decide to buy or not this device (root is very important to me)
Click to expand...
Click to collapse
I have good hope that this device can be rooted considering my past Samsung devices, it is only a matter or time.
I'm downloading the files again now, and going to try! Will report back a.s.a.p.
Edit:
Installed everyhing from your files in Odin: BL, AP (patched), CP, CSC and:
It worked! Magisk installed, Magisk Manager updated. I could install AdAway and it asked for root permissions.
But... after reboot Magisk Manager said it is NOT installed anymore. Now what?
Edit 2:
It seems Magisk sometimes fails to load when booting. After some reboots, it is back again and AdAway works. So end of the story: IT WORKS, and it Magisk starts to nag that is it not installed, just reboot a couple of times, and enjoy your rooted phone
Edit3:
Screenshots:
https://i.postimg.cc/wMrbLSpZ/Screenshot-20190515-094200-Magisk-Manager.jpg
https://i.postimg.cc/WbDyTbmv/Screenshot-20190515-094205-Magisk-Manager.jpg
https://i.postimg.cc/wjLbRfb4/Screenshot-20190515-094325-Magisk-Manager.jpg
https://i.postimg.cc/BQdV69N1/Screenshot-20190515-094336-Ad-Away.jpg
Captain Beretta said:
I have good hope that this device can be rooted considering my past Samsung devices, it is only a matter or time.
I'm downloading the files again now, and going to try! Will report back a.s.a.p.
Edit:
Installed everyhing from your files in Odin: BL, AP (patched), CP, CSC and:
It worked! Magisk installed, Magisk Manager updated. I could install AdAway and it asked for root permissions.
But... after reboot Magisk Manager said it is NOT installed anymore. Now what?
Edit 2:
It seems Magisk sometimes fails to load when booting. After some reboots, it is back again and AdAway works. So end of the story: IT WORK, and it Magisk starts to nag that is it not installed, just reboot a couple of times, and enjoy your rooted phone
Click to expand...
Click to collapse
Yay I'm happy it worked!
Magisk isn't loading because of you want to boot with magisk you need to hold the volume up and power button together untill you see the bootloader unlocked warning and it asks your to press the power button to continue then release press the power button. I usually press volume up and power button again for 2 sec to make sure and that's it! Reboot won't boot with magisk sure make sure u use this method each time you need to reboot!
Avicohen21 said:
Yay I'm happy it worked!
Magisk isn't loading because of you want to boot with magisk you need to hold the volume up and power button together untill you see the bootloader unlocked warning and it asks your to press the power button to continue then release press the power button. I usually press volume up and power button again for 2 sec to make sure and that's it! Reboot won't boot with magisk sure make sure u use this method each time you need to reboot!
Click to expand...
Click to collapse
That's...unfortunate. Any way to unlock samsung fully?
infearno said:
That's...unfortunate. Any way to unlock samsung fully?
Click to expand...
Click to collapse
It's not that bad, even if you accidentally booted without magisk just turn off the phone and boot with the way I mentioned and magisk is back!
If you normally power up your phone just pressing the power button with this method just add the volume up and hold both button together for 4 to 5 sec.
Right now it's the only way to root that I found. Maybe with twrp things will get easier.
And one more thing if you install magisk module don't press reboot after your install just power off and boot the way I mentioned that's it.
Avicohen21 said:
Yay I'm happy it worked!
Magisk isn't loading because of you want to boot with magisk you need to hold the volume up and power button together untill you see the bootloader unlocked warning and it asks your to press the power button to continue then release press the power button. I usually press volume up and power button again for 2 sec to make sure and that's it! Reboot won't boot with magisk sure make sure u use this method each time you need to reboot!
Click to expand...
Click to collapse
I tested a few reboots, and this is how my A70 behaves:
X Reboot without pressing any buttons: no Magisk
X Reboot, pressing the power button when prompted: no Magisk
V Reboot, hold power button + volume up button, press power button to confirm: Magisk :victory:
Well, that's good enough for me! I am happy :laugh:
Captain Beretta said:
I tested a few reboots, and this is how my A70 behaves:
X Reboot without pressing any buttons: no Magisk
X Reboot, pressing the power button when prompted: no Magisk
V Reboot, hold power button + volume up button, press power button to confirm: Magisk :victory:
Well, that's good enough for me! I am happy :laugh:
Click to expand...
Click to collapse
Yeah that's right my English is not perfect maybe I didn't explained it good enough but that's what I meant! Thank you for trying. That's good enough for me also.
I also installed EdExposed and it's working good with modules that are confirmed to work with Android pie.
Next thing is trying to flash mods with flashify or something because we don't have twrp yet.
There is more good news!
I got EdXposed working following this manual, using the SandHook version: https://magiskroot.net/download-xposed-for-android-pie
It was really easy, just download and flash/install these files:
Links:
Riru core: https://github.com/RikkaApps/Riru/releases
EdXposed Sandhook: https://github.com/ElderDrivers/EdXposed/releases/tag/v0.4.1.2
EdXposed Installer: https://github.com/solohsu/XposedInstaller/releases/tag/Ed_v2.2.4
Don't forget to reboot with the button combination trick mentioned earlier!
this way can flash Treble?
5dprince said:
this way can flash Treble?
Click to expand...
Click to collapse
Not.
@Avicohen21 I want to do this, but now this magisk canari, to patch FW, is not longer available to download...
point me there, please
thanks
ivanox1972 said:
@Avicohen21 I want to do this, but now this magisk canari, to patch FW, is not longer available to download...
point me there, please
thanks
Click to expand...
Click to collapse
Here's the copy of it. View attachment 4768110
@Avicohen21 Actually I tried it on tab s5e- should be same procedure.
But I got fail result on odin flash patched ap...
Is this normal? 1 fail 0 success? or not- must be 1 success?
thanks
ivanox1972 said:
@Avicohen21 I want to do this, but now this magisk canari, to patch FW, is not longer available to download...
point me there, please
thanks
Click to expand...
Click to collapse
It also works with version 7.20 if you can't find an app I'll upload it.
ivanox1972 said:
@Avicohen21 Actually I tried it on tab s5e- should be same procedure.
But I got fail result on odin flash patched ap...
Is this normal? 1 fail 0 success? or not- must be 1 success?
thanks
Click to expand...
Click to collapse
If it failed maybe magisk didn't patched AP correctly try to extract the AP file again from the firmware file and then patch it in magisk again.
I extract with 7zip and got all ok in magisk. Newest 214 build.
But got success 0 fail 1 as result
Can't be ok like this?
@Avicohen21 I almost bricked it. Send me on pm your telegram contact or something to send you some pictures

[RECOVERY] LineageOS Recovery for F700F

This has been tested only on my F700F model. Others may not work including US ones which are bootloader locked(unless you pay for an unofficial unlock, then it might* work).
It will 100% not work on the 5G variant which is an entirely different phone.
Disclaimer: While i use this on my own personal phone, there are so many (thankfully reversible) ways one could mess this process up. If you choose to install this, i'm not responsible for anything you do with your device.
Installation Guide:
Step 1: Unlock the bootloader
WARNING: ALL data on your device, including apps, settings and files in internal storage, will be lost. You do not need to repeat this if you didn't re-lock your bootloader.
1. Open "Settings"
2. Turn on "Developer mode" by going to "About phone" -> "Software information" and pressing "Build number" for several times.
3. Go to main menu of "Settings" and at the bottom you will find "Developer options"
4. Go to "Developer options". You will find a toggle "OEM unlocking". Turn it on.
5. Skip to substep 8 if your device reboots to "Unlock bootloader?" screen. Make sure the toggle is on and then turn off your phone.
6. With the phone off, hold "Volume Down" and "Volume Up" button, connect your phone to a computer via a cable. (don't use charging only cables)
7. Release the buttons after you see the "Warning" screen. Then, hold the "Volume Up" button.
8. You will see "Unlock bootloader?" screen. Proceed and unlock your bootloader by pressing "Volume Up" button.
9. Your device will be reset to factory settings. Proceed with the Setup Wizard. Only connect to network via Wi-Fi or cellular and skip everything else. (to save time as data will be cleared again later.)
10. Repeat substeps 1-4 to validate that "OEM Unlocking" is on. If it is not, turn it on.
11. Repeat substep 6.
12. Release the buttons after you see the "Warning" screen. This time, press (not hold) the "Volume Up" button.
13. You will see "Downloading" screen. On the top left, there are some important info.
14. Pay attention to "OEM LOCK" and "REACTIVATION LOCK". If both of them are "OFF", you have unlocked the bootloader.
Step 2: Disabling AVB
1. Reboot to DOWNLOAD mode. If you are already in the download mode, skip to substep 2.
2. Download Odin 3.14.4 or newer and make sure Samsung USB drivers are installed.
3. Open Odin and put the vbmeta_disabled.tar into USERDATA slot and click "Start"
4. Your device will reboot but it will not boot. This is built upon into system as vbmeta signature has changed.
5. Your device will reboot into RECOVERY mode automatically and prompt "You have to reset your device to factory settings". Use "Volume Up" or "Volume Down" button to move and "Power" button to select. Confirm and reset the device to factory settings.
6. This is the last time the data on the device has to be cleared. Afterwards, if you don't re-lock bootloader or re-enable the Android Verified Boot, you will not lose your data. Be aware, a stock firmware package contains a Android Verified Boot Metadata Image (vbmeta.img) with verifications enabled. You will need to flash the vbmeta_disable image (put into USERDATA slot) along with the stock firmware (use BL, AP, CP, CSC slots) to make sure AVB is not re-enabled and the data is preserved.
With bootloader unlocked and AVB disabled, it is now possible to boot modified images on the device.
Step 3: Flashing the recovery image
Place the downloaded .tar into the AP slot in odin, and once again with it in download mode, hit flash. Just after hitting flash quickly grab your phone and hold the VOLUME+ and POWER keys. As it reboots it should go into recovery mode. If it boots normally anyway, try turning it off and powering with that key combination. Sometimes samsung's system likes to replace a custom recovery with the stock one which is why it's important to enter it first thing after flash (this may have changed with newer models idk). If it boots into the stock recovery instead, try again.
Step 4: (optional?) Disable encryption
Once booted into recovery, adb sideload the disabler zip and afterwards format data. Reboot the phone and encryption should be disabled, and you can see files in internal storage. If you do flash a stock package that contains a vendor file (super.img or vendor.img) you will need to redo this.
Bugs: none so far
Downloads Folder
Kernel Source code
Special thankies to @Vaughnn for his s10 lite trees on which this is largely based upon.
reserved 1
reserved 2
Does this recovery work similar to twrp? For example, can you flash zip files in the same way? Or does anything need to be changed in twrp-compatible zip's to work with this?
davecotefilm said:
Does this recovery work similar to twrp? For example, can you flash zip files in the same way? Or does anything need to be changed in twrp-compatible zip's to work with this?
Click to expand...
Click to collapse
they should work, in theory. You will have to confirm the flash when it says "signature invalid", but that's about it.
Some older zips may not work due to how SAR is handled(not at the recovery's fault), and mounting /system is kinda wierd, but it works.
Is it possible to port TWRP as well ? Tgx for great work anyway
Rainbow_Dash said:
they should work, in theory. You will have to confirm the flash when it says "signature invalid", but that's about it.
Some older zips may not work due to how SAR is handled(not at the recovery's fault), and mounting /system is kinda wierd, but it works.
Click to expand...
Click to collapse
So, having my phone set up and rooted, encrypted data I'm assuming on stock, can I flash this recovery without losing data? Or will it factory reset? And finally, will it work with Android 11?
davecotefilm said:
So, having my phone set up and rooted, encrypted data I'm assuming on stock, can I flash this recovery without losing data? Or will it factory reset? And finally, will it work with Android 11?
Click to expand...
Click to collapse
The recovery itself will not wipe your data. Flashing the nulled VBMETA however (which is required) will. As for android 11, i don't see why it wouldn't work whenever it releases.
Rainbow_Dash said:
The recovery itself will not wipe your data. Flashing the nulled VBMETA however (which is required) will. As for android 11, i don't see why it wouldn't work whenever it releases.
Click to expand...
Click to collapse
Thank you. I'll probably get into development on Android 11 or 12, once I get over how awesome this device is on stock (with magisk though obviously). When I do I'll make an overclock kernel probably
Hi, can I flash a custom rom/ lineage os on f700f/ds
Uploaded an updated build for lineageos recovery. This should be overall much better in so many ways, being rebased on 18.1 sources. Should support flashing more packages like magisk, opengapps, and maybe even lineageos builds (that may or may not come soon idk). Atleast these are what i tested.
So can I use this recovery to flash magisk

Categories

Resources