Connector broken - MDA, XDA, 1010 Accessories

I'm looking for the connector between the charger cable en XDA because my connector is broken.
Could somebody help me out with this?
thanks in advance.
Paswal

Related

cable of headphone (XDA-I) is cut from connector

Cable of my earphone (XDA-I) has been cut from its connector (plug to XDA-I).
I will try to weld it, but I dont know where each of the cables (blue, red, white and copper) has to be welded on the connector (with 4 pins).
Can someone please post a suggestion?
http://xda-developers.com/connectors/
Maybe this will helpful.
Yooooo thanks
Sallala said:
http://xda-developers.com/connectors/
Maybe this will helpful.
Click to expand...
Click to collapse

[Q] Where?: S PLUS tutorial to soldering usb charger connector?

I'm having problems with usb charger connector of my Galaxy S Plus
I just bought two connector from ebay, but I can see pins are very small.
Where can a find a tutorial about soldering usb charger connector?
Thank you in advance (And sorry my limited english).

Phone Cover Hard Case With Wireless Charge Receiver For LG P990

I found this:
http://www.ebay.com/itm/Phone-Cover...Cell_Phone_PDA_Cases&var=&hash=item2a30c11d8e
on Ebay.
It seems its a cover for QI charging for our good old phone...
But i am insecure. For what is the cable and the plug on the cover???
The pictures are not very helpfull... Or must i put the plug into the mico USB connector? If so.. this looks like a......
Bastlwastl2010 said:
I found this:
http://www.ebay.com/itm/Phone-Cover...Cell_Phone_PDA_Cases&var=&hash=item2a30c11d8e
on Ebay.
It seems its a cover for QI charging for our good old phone...
But i am insecure. For what is the cable and the plug on the cover???
The pictures are not very helpfull... Or must i put the plug into the mico USB connector? If so.. this looks like a......
Click to expand...
Click to collapse
.............................................

[solved]Nook won't charge-possible 1$ solution (needs soldering)

I was looking for a solution to this problem and after opening the nook I found out that on the socket one of the contacts is pushed towards inside - I've strighten it and tried to insert the cable but the cable pushed the contact again. So I glued it with some epoxy glue and currently I'm waiting until it cures.
Sent from my Redmi Note 3 using Tapatalk
It turns out that it wasn't the main problem - the nook now is working on power from the charger but it isn't charging the battery. My next try is to solder on a cheap lion charging board from china inside. I couldn't find any 5v test point but there is space for a capacitor near the connector and on the battery connector there are batt+ and batt- test points. This should be enough for the charger.
edit:
Its working!!
i've used a cheap lion charging module from china for 1$. I've cut out the microusb connector, wrapped it in duct tape and fitted it inside the nook.
It's slower than the original charger - only 1A but its working
Hi dkuku,
Thanks for the post.
Could you tell me where the orange USB wire goes?
TIA
andtron said:
Hi dkuku,
Thanks for the post.
Could you tell me where the orange USB wire goes?
TIA
Click to expand...
Click to collapse
look at the attached picture - its quite easy to solder

Help!! Mhl adapter wiring [n7000]

Plzz... Help me to fix wiring of samsung mhl adapter..
I could be wrong, but it looks like, one of the pads is destroyed (lifted up). I have 2 different MHL adapters here, both have different wiring (dual sided on PCB) but have 6 soldering pins.
vs3074 said:
I could be wrong, but it looks like, one of the pads is destroyed (lifted up). I have 2 different MHL adapters here, both have different wiring (dual sided on PCB) but have 6 soldering pins.
Click to expand...
Click to collapse
me to have 6 pins..one is lifted up i think..
but can you tell me the sequence of wire so i can solder it one by one!!

Categories

Resources