:roll: is there a Expansion Jacket for the xda 1 :?: :idea: :?:
there are no jackets for xda1 at all
but you can get a serial cable for it and thats rs232
Related
I ordered connectors from gomadic corp for xda but they don't fit perfectly to Qtek 1010. The latch does not work and the arrow markings on the connector need to be facing down instead of up.
Anyone here knows of any source for Qtek connectors?
samohile said:
I ordered connectors from gomadic corp for xda but they don't fit perfectly to Qtek 1010. The latch does not work and the arrow markings on the connector need to be facing down instead of up.
Anyone here knows of any source for Qtek connectors?
Click to expand...
Click to collapse
That's because the iPaq uses the same connector, except facing the other way. There is no specific Qtek connector. Qtek 1010, XDA, MDA, SX-56, they're all the same device: the HTC PW10.
Hi, can you help - 02 can't! I want to connect to the black plug, labled as number 13 - in the car kit user manual. its a short lead from the main thicker wire from the "box" to the xda holder.
What type of plug is it? anybody know where i can get the other side to connect to my other bits of kit.
thanks in anticipation. Simon :shock:
I dont know exactly the connecter but if you have a Maplin store local to you, it might be worth a visit, they have an incredible array of connecters, converters, adaptors etc.
Hello !
I assume that you are talking about the flat connector, if this is the case it's mensioned for data in/out like GPS etc,
For what purpose do you need this connector ?
The connector i am looking at it a flying lead off the main loom from the car kit electronic box to the xda holder. i am looking at using it for gps. i know which wires to use and have the system working fine. its just not a very elegant solution. i would like to make up a short lead using this connector and my gps to offer the system to my parants cars and my sister. the way i have done it would invalidate the warrenty on the car kit.
thanks. simon.
Hello Again !
smart (car manufacture) have a GPS which fits directly to the connector of the harness.
Part nr. is 0015829V001000000 and can be delivered by any smart-Center in Europe. :lol:
I have a 22 pin Connector from an IPAQ 2215, does anyone know if they are compatible. I found the connector page but this isn't covered (at least not that I could find).
I plan on using it as a connector for a new docking/charging base for my SX66 in its Aluminum case.
Found my own answer
Most IPAQ's connectors are the same, 3800 and 2200 series use same connector and it is NOT compatible with the BA. Found the pin out for the IPAQ connector and compared it to the one on wiki and nope don't even come close to matching.
I think I'm going to upgrade to the Kaiser, Does anynone know if the car mount for my hermes will work with the Kaiser? Also has anyone that upgraded regret it??
I really just want the GPS so I dont have to carry around my BT GPS reciever. Oh how long does it take to acquire a signal? And how many sats can it track? I will dig into the threads for this but if someone can tell me that would be nice too
Thank you in advance !
How does the car mount for the hermes mounted?
just fyi..
my tilt/kaiser fits into my tytn/8525 metal case with no problems so it would only be logical the car mount wouldn't have any problems. GPS acquisition is about 5 give or take 1 or 2secs(depend on your locaiton(in building/outside). i get about 5 in my room and 8-10 when i'm outside.
apparently from what Ive heard in the accessories forum about this question (which is where you might want to direct this next time) is that the Tilt will fit with the Hermes car mounts, but not perfectly, meaning it might fall out.
copualt3 said:
How does the car mount for the hermes mounted?
just fyi..
my tilt/kaiser fits into my tytn/8525 metal case with no problems so it would only be logical the car mount wouldn't have any problems. GPS acquisition is about 5 give or take 1 or 2secs(depend on your locaiton(in building/outside). i get about 5 in my room and 8-10 when i'm outside.
Click to expand...
Click to collapse
Thank You this is most helpfull, but when you say 5 do you mean mins or secs??
Doug2873 said:
apparently from what Ive heard in the accessories forum about this question (which is where you might want to direct this next time) is that the Tilt will fit with the Hermes car mounts, but not perfectly, meaning it might fall out.
Click to expand...
Click to collapse
I will use the other forum next time, Thank you for your reply thuogh, guess I will need to buy a new car mount
5 seconds silly..
The Kaiser/Tilt fits in the Hermes car mount... but not snugly. If your, a little duct tape in the car mount should fix the problem.
Kaiser seems to need a better view of the sky to lock into satellites... than say a Garmin nuvi.
I've now a kaiser with a hermes car holder. It fits but not perfectly because I think the thickness of kaiser is little less then hermes, so my kaiser is not perfectly hold. It's not a problem for me. The only problem is that the camera button is half pressed when kaiser is on the holder. I don't know if this could be a problem, but I've tested tomtom and bluetooth car kit and I haven't found any problem.
Thank you all!
Thanks for all your input! It has been really helpful I have been decieding to sell the car mount and my BT GPS recv. in one big lot.. I think I will..
For your information:
The USB jack from Kaiser is slightly repositioned (2mm in heights, 3mm in width) compared to the one on Hermes.
The passive Holders without USB Jack should work all fine because outer dimensions fit perfektly.
When using an active Brodit Car Mount like me then u will get into slight problems because the jack doesnt fit anymore. But no reason to panic: Its not a big deal to modify the Holder.
Simply use a sharp knife and seperate the usb-block (where the usb jack and its cable are connected) from the holder... next u need to clean the position of the usb-block on the holder from possible glue-artefacts. Additionally, flatten the holder for about 2mm. Next, put your Hermes into the holder, plug in the usb-block and put some glue (i used 2 component epoxy) between the holder and the usb-block. Let the glue beome hard and voila: a perfectly fitting, individual Carmount for your Kaiser!
Sounds more complicated as it is... this holder fits now better than the original with the Hermes - and honestly: 120 Euro for just the new Kaiser carmount from brodit? No Thanks
Our good freinds at DSL Developments will shortly have in stock the 'Brodit PDA Active Holder Tilt Swivel for HTC HD2'.
This is described as:
The active holder charges your battery when it is in the holder. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Connects to the vehicle's cigarette lighter socket, 12/24 Volt. Attach onto a ProClip Mounting Platform. Can be used with HTC original portable Handsfree. Item No :512086
We were lucky enough to be provided with one of the first brackets available in the country and as you can see from the attached it suits the HD2 well.
As anticipated with Brodit the holder itself has the standard 'Brodit' mount adaptor which means if you already have a Brodit mount fitted to your car you can just unscrew the universal mount portion of the holder and screw in your new HD2 holder in seconds.
Click to expand...
Click to collapse
[READ MORE]
Tekguru said:
[READ MORE]
Click to expand...
Click to collapse
I am using the same brodit holder that I first bought for my ipaq 6515, just retrofit it alittle by adding a felt material on both side of the holder, and viola!