Innopocket Aluminum Case - MDA, XDA, 1010 Accessories

Is it just me, or does the Aluminum Innopocket case rub the paint off your MDA/XDA I??? I just figured that a $40 case shouldn't do that to the $450 unit that it is supposed to be protecting???? I love the case, but you can tell that the paint is getting buffed off the left side corners, and the case rubs right below the antenna. Any comments/ suggestions? I was going to grind out the antenna hole a little, but I don't want to permanantly damage my case. thanks.

I had a ProPorta ALU case and it grips the XDAII by wrapping over each side. The process of sliding the XDAII into and out of the case started to cause rub marks where the case contacts the XDAII.

Related

Found some plastic cases, but not the perfect one

Hello.
Looking around for a plastic, soft case for XDA II, i found:
http://www.javoedge.com/simtrix/productMtce/fw_O2Skin.jsp
not soft (i suppose), doesn't protect the screen. no clip belt.
and:
http://secure.proporta.com/proporta/F02/PPF02P05.php?t_id=743&t_mode=des
hard plastic. Protects the screen, with a flip. no clip belt.
and:
http://www.krusell.se/product.php?s=2&prodGrp=&product=1255 .
half plastic, half leather (so it's thicker). Protects the screen. With clip belt. Peraphs the best.
But i'm exactly looking for something similar to the old phone plastic skins, like:
http://www.thesimpleshop.com/category/34
Can anyone help?
tnx.
In my opinion a combination of metal and plastic woul´d be best.
Plastic only used to show the screen (and protect it) and the metal body to protext the rest.
To assure a "normal" signal strength I'd provide the metal body with several cut-outs, especialy where the antenna is placed.
Maybe I should apply for a patent... :lol:
Hopefully somone at Proporta and Krussel is wathing topics like this...
Damn, krusell is swedish... well i´l be recieving my Krusell (Half plastic, classic case) tomorrow already. And it only costed me around 20$!

Aluminum Metal Case

I received yesterday my protection for Leo. I share with you the results of this:
http://www.flickr.com/photos/[email protected]/show/with/4210742282/
For shipping this protection:
http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000801&products_id=26364
Thanks for sharing; however you would have been better off posting in the Cases thread where we all go to see what's happening in the world of cases.
WB
Agree with above poster, can a mod fix this?
Nice case! ive also ordered 1 last week at PDAir, the 1 without a screen, so easy acces, but fewer protection. I am hoping its more solid so i can put it in my back pocket without getting a red face everytime i realize i accidently put it there...
When did you order it and did it took long (i am eager to get mine, but now hope is gone till monday or tuesday...)
I disagree.
The "Cases" thread is too long and too complicated for discussing any one specific case.
Anyway I ordered mine just a moment ago and would very much like to hear how quick was the shipment, how snug is the fit and how reassuring the neoprene feels
It's a shame they opted for a plastic screen protector instead of either a window-less aluminum door or a transparent cover that lets you work with the touchscreen.
mohasea said:
I received yesterday my protection for Leo. I share with you the results of this.
Click to expand...
Click to collapse
mohasea,
How thick is the plastic cover over the screen?
Does the plastic cover flex?
Do you think the plastic cover would prevent the screen being cracked if dropped screen down on ummm concrete?
Duperman said:
It's a shame they opted for a plastic screen protector instead of either a window-less aluminum door
Click to expand...
Click to collapse
I totally agree, wish they had a solid aluminum front door instead of the window cut-out covered in plastic or the other option they have of no plastic window cut-out. I would order one now,even not having my Leo yet, just because the front door was solid aluminum.
I am going to contact PDair and see if they would leave a few front doors out of the cnc cutter and have a full cover aluminum
Would you like one too, Duperman ?
Thank you,
Monnie
I have ordered an open screen case despite it may not fully protect the screen. HD2 has a glass screen and it is hard enough against scratch as what has been in iphone.
Would you like one too, Duperman?
Click to expand...
Click to collapse
Absolutely
Mine, the one without screen plastic, is supposed to arrive between now and Jan 27th next year...(sometime)
take care
Anyone got theirs yet?
Would love to see some detailed photos and a review of the case pros/cons
Thank you,
Monnie
I'm debating whether to go with their leather flip case or this aluminum case...
I got this case and immediatly wished there was no plastic screen on the front door. So, I held it over some boiling water for about 2 mins and and then used my thumb nail (not kidding it was easy) to pry the plastic from the metal. The whole lot peeled off easily, i replaced the foam into the case and BAM perfect case. (be careful not to rip the foam, but if you do it will still stick back. also the foam stretched out a bit but pushed back into shape no problem. TIP: Work from the front side of the case, wedge your nail into the seem and loosen it all the way around. If it starts to get tough again, hold it over steam for a while longer.
Also.. when the plastic was still inplace and the case door was closed, there would be random screen presses and that was not cool, however now that the plastic is out, i can leave the door closed, press when I want too, AND there is no random case presses
I know this sounds like a poor fix, but it worked awesome and it looks like it was SUPPOSED to come this way.
Now all i need is for my zag shield (front only) to show up and im perfectly protected (minus water damage dammit)
awesome case guys im not kidding. you dont have to put the nubbin on in the back either so it doesnt add much bulk to teh phone. good luck yo.
Got mine too and I use the black open faced aluminum for local use and insert the whole unit;
aluminum case and all into the Maxpedition "Rat" wallet for carrying on belts etc.... http://www.maxpedition.com/store/pc/...&idcategory=11
Like it alot....
FWIW
well, do not kill me if I say so .. but it is ugly as hell.
I do not say that it does not protect the phone, or the the finishing it's not ok .. but from a slim phone with a huge screen, it looks like a bullet proof brick with a screen.
The whole idea of an elegant smartphone it's gone.
Small question: what do you hate about the original leather case?
It is elegant, slim easy to use and protect the phone in normal use conditions or small accidents.
Capdase Alumor Metal Case
Bought this silicon w/ aluminium backcover case by CAPDASE in Hong Kong, adding a more "solid" feel over the pure silicon case. It comes with a CAPDASE screen protector as well.
http://www.mobimega.com/capdase-alumor-metal-case-htc-hd2.html
Beware that the silicon case may not glue well to the aluminum backcover (I think it's the factory problem) which may leave a small gap between them when you put the phone in. I have to apply some glue to fix that myself. Apart from the case is nice and not too costly.
byronlee said:
Bought this silicon w/ aluminium backcover case by CAPDASE in Hong Kong, adding a more "solid" feel over the pure silicon case. It comes with a CAPDASE screen protector as well.
Beware that the silicon case may not glue well to the aluminum backcover (I think it's the factory problem) which may leave a small gap between them when you put the phone in. I have to apply some glue to fix that myself. Apart from the case is nice and not too costly.
Click to expand...
Click to collapse
Hi,
I am seriously thinking about ordering one for my Desire (A8181).
But what I'm not able to find, is how it works. I mean, you seem to describe the case as a silicone skin, with a metal plate sticked to it.
I thought it was more like a silicone skin with another semi-case to "clip" over the silicon....
Can you confirm if I am right or wrong?
And can you post multiple angles pictures?
Thank you, it would be much appreciated!
thanks but
so uglly
Ohh Great!
Thanks for the pictures! To me is one of the best cases i've ever seen.

Review - BENTOBEN Shock Absorbing Dual Layer Hybrid TPU Slim Fit Hard Case - Black

Note: I received a discount on this case in return for reviewing it.
This case is better than others which claim to offer a huge amount of protection because it is not as bulky as most of the others. One reason could be also because it does not in fact include a cover with a built-in screen protector for the front, although there are lips which do stick up around the front to protect it when the phone is placed face down on a table.
Wireless charging works well with this case as well which can be an issue with other protective cases.
The back of the phone is a shiny plastic material which can be a fingerprint magnet to a very small extent, but that is not nearly as noticeable as an issue as the phone has on the back when it has no cover. The back is also curved on the sides like the bare phone itself, so it is very comfortable to hold.
In order to make up for some possible slipperiness on the very back, you can see by the photos included that that is more than made up for by the rubber "grippy" sides. I would have preferred the side on the phone with the volume buttons to have the same rubber material all the way up the side as the side of the phone with the power button, but that is just my preference with which everyone may not agree.
On the front, the top lip and the bottom lip around the screen are hard rubber, while the sides edges are in fact the same plastic as the center of the back of the phone. They do not fit right up to the edge of the glass the same way - so on the front you can see a little of the metal edge on the top and bottom front edges of the phone with this case. However, it is just this one 'slight flaw' that makes the next paragraph possible:
It may sound counterintuitive, but what I like most about this case is that is not only a very protective case for the phone, but it is also very easy to slip on and off the phone at the same time - the rubber and plastic pieces do not have to be pulled apart from each other to put the phone in or to take it out. Just grap a couple corners and with a little effort it will pop off - not so easy that it would ever slip off on it's own - it is very snug. It may seem like a silly thing, but I have a custom proclip holder in the car (for the bare phone) - and I like to slip my phone into that when I get into the car. As that requires removing the case and slipping it back on, when I am using the other protective cases for my phone I am forced to just not use the proclip holder those times when I am driving - except not with this case!
All in all I really like this case and I'll be using it a lot!
wondermanyoulove said:
it is 4.99 dollars in Ebay
Click to expand...
Click to collapse
Probably one of the other reviewers. I still have mine.

Protect the base of the Gemini

Any ideas on a nonslip thin cover for the bottom of the Gemini or very small felt or rubber feet?
I expect to receive my unit soon.
My idea was to use silicone to create my own "feet".
The idea is to cut feet shaped holes into thin foam, the kind you would use for scrapbooking, stick the foam onto the bottom of the gemini, fill the cut out holes with a thin layer of silicone (should be neutral curing silicone, not the type that causes a vinegar smell when curing), then remove the foam molds and let it cure.
Since I haven't physically held a Gemini PDA in my hands yet I still don't know where the rear feet underneath the LCD need to be so that the device doesn't tilt backwards. Possibly the rubber feet will need to be on the metal hinge itself, which would make things a bit more complicated.
Silicone shouldn't stick that well, so I expect to loose a foot now and then and I hope that it will be easily removable without damaging the devices case.
drwatson said:
I expect to receive my unit soon.
My idea was to use silicone to create my own "feet".
...snip...
Silicone shouldn't stick that well, so I expect to loose a foot now and then and I hope that it will be easily removable without damaging the devices case.
Click to expand...
Click to collapse
Or just get wide enough grip tape to cover the entire bottom plate. That's what I plan to do with mine since cases that allow you to keep using it are pretty much impossible with this sort of device.
Oh, how nasty I can't imagine this will ever come off again
If you want to make feet, you guys should really check out Sugru! It's amazing stuff. It makes for a great present too. They should just about give me a commission, haha
https://sugru.com
I had a leftover woven carbon fiber sticky sheet that I cut to size and put on the bottom metal plate. Protects and looks good.

My review of the jjnusa note 20 ultra leather case

https://www.amazon.com/JJNUSA-Handma...ef_=ast_sto_dp
you know i never thought trying to find a case was going to leave me so hard pressed. note i do not mind the camera bump one bit. but they could have rounded out the camera hump a bit more. not the corners, but where the surface meets the edges and also they could have slanted the sides a bit more angled. who knows they did pull it off pretty good.
still on the camera bump.
note: with JJNUSA leather case you will be covering the mic on the camera bump. if that is a problem for you look elsewhere for a case.
i have received 200 in incentives to order goodies when i got my phone pre ordered and used it to order a few cases.
cases i ordered:
samsung rugged: bulky, heavy, don't like the texture on the back and flimsy kickstands that shoot off when used
samsung leather case: upgrade from last years, 2g lighter. seamless, but warps at the bottom. good cam protection.
samsun silicon: unsure if food grade safe. and slippery as glass
-other cases-
spigen Rugged Armor: oddly best all tpu case with carbon fiber accents. the back is slippery if trying to reach across the screen. side bumpers have one way slip grip and flimsy. camera is well protected. pen cut out too deep corner exposed but covered. top /bottom bumper good but top may block ear piece. 2g heavier then jjnusa leather
...now my official review of the JJNUSA Handmade Leather Case...
NOTE i used amazon prime
don't let the first pic they have on amazon throw you off, but what bothers me is the video they added to the product and it is of the s20 ultra; the camera lens is so scratched. i am still baffled how they did that. then again we will see in due time, because i can not stand the samsung leather case(which got me hooked on leather cases oddly) it is too slippery. the jjnusa case has tpu sides and saddle leather on back with plastic on the inside that the phone rests on. but i will say the leather on the back is so soft i think it sorta makes up for the lack of suede like the official samsung case has. then again the leather is so thick its' edges pop out the mold a teensy-weensy bit, but i doubt with proper use and not picking at it it will survive for a long time. with the 5% off coupon i also got another 1 usd off(who knows if it was the amazon prime). so for 19.95 it is a steal. most other leather cases are $30+. a steal; why may you say? hold on let me get to the rest of it. if we all remember the lg g4 leather back it was a looker. that was it, because it scratched easily and punctured easily. then we go onto the samsung leather case that scratches easily with minimal show. further more i can not say what that will mean over long term usage with this case from jjnusa. treat it lightly and it should be fine. now back to the leather on the jjnusa case. the leather reminds me of the type you get on a saddle and does not separate from itself. that is a plus. but a minus if the antiquing they use comes off very very easily?, and it does(con or not?) i had a cane that had antiquing and it turned my hands black, but after it leveled out it was fine. you know they always slap so much on to fill in the design that almost certainly more then half they put on will rub off. i have rubbed off some already. hence it would not rub off like wow, i had to use my nail. no way does it show like scratches on the samsung leather case. either way the extra antiquing will no matter what fade away over time and settle down to where it should be. i still think it will look good. at the same time the leather is much more scratch resistant then the latter. and the design and the look really grew on me. now on to the sides. the power button and volume are labeled with symbols and i like it even though i will never look at it. what else i like is that they are tpu like the rest of the sides. the tactile of the buttons are sturdy then again not too stiff not too mushy. then there is a bonus or an achilles heal; you move down the same side as the buttons and find a wrist strap punch out so you can add a wrist strap. have not tested it, seems like it should be worthy of use and not fearing. the bonus is removing the phone from the case, it does not shoot out like it does with the samsung leather case does. still it holds it in better. this is where i tell you that the jjnusa case has way better screen protection that leaves a better feel in the hand. the samsung leather case has a squidgy spongy top and bottom. the bottom is already warped and i never used it; i just put it on a few times and took it off. also a fail for the bottom bumper is the difficulty to remove the spen without nails. the jjnusa case is cut out just right and since it is thinner and more stiffer in a good way you can press your thumb or finger and hear that satisfying click to eject it. with that said the top and bottom bumper are raised higher then the samsung to protect the screen. the samsung case is more flush and flimsy.
i am a happy camper and if it fairs well i will update to 5 stars from 4, but i am really thinking at the price to slap down for another. as we all know leather cases do not last as long as other types
the reason i gave it 4 stars is i never really heard of JJNUSA till i saw them on etsy.com and since they where based in china i thought meh. then i thought to ebay's third party cases and said but leather? does not smell much like leather, oddly that is how saddles with the same type of leather smells. or it could be the antiquing they used and the shipping package. it was not shipped in a box or cheap plastic, it was in a cloth sleeve in a sealed padded envelope. JJNUSA do claim Oregon origins... yeah right etsy.com says ships from china.
i have played around with plenty of cases and phones in cases so it's not like i only have really had the note 20 ultra... just do not get one of them ultra thin all tpu cases. i have one for my lg g4 and only really protects the sides and back. busted the screen.
I have already dropped it having it about 3.6 feet drop going swap when it landed on its' back side. my heart sunk, but the case did its' work and saved it. a plus for the case. it was not dropped it was knocked down from a propped up position onto a hard wood flooring

Categories

Resources