HOW TO SUT OFF MY 9090 - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hi I've bought a qtek 9090 smartphone, but I've seen that's always ON
Can anybody tell'me if there's a program to INSTALL FOR SHUTTIN' OFF MY PDA?
thanks :roll: :roll: :x

It says here to hold power button for 2 seconds to power down, I assume you would also need to switch to flight mode beforehand to switch of phone radio.
http://www.qtek.nu/default.asp?nc=3700&id=80&element=74

Related

Software to put BA in bootloader Mode

My powerbutton is broken so I can't put my phone in bootloader mode anymore. I've got WM5 installed and activesync 4.1. Does anyone know if there is a possibility to put my phone in to bootloader mode without using the 3 button combination? Like with software or something?
BTW I must say that WM5 works just fine with me!
the power button broke on my xdaiis and I took the thing
apart and realigned switch..
all great since.. you need the swith to turn the screen bcak on
The thing is that the button had come off totaly. When I opened the phone it fell out. Somehow the button was damaged too, so it can't be pressed anymore.. The other alternative is to get let it fix, but that will cost me about 80 euro. And I don't need the button for anything else since I havesoftware to turn it off, and the phone also starts (if battery taken out) when you soft reset it. Whith the older versions of windows mobile it would go in to bootloader mode using just the installer, but since WM5 this doesn't work anymore.
dblfun said:
if there is a possibility to put my phone in to bootloader mode without using the 3 button combination?
Click to expand...
Click to collapse
The buttons are documented here
http://wiki.xda-developers.com/index.php?pagename=BlueangelGPIO
and here
http://wiki.xda-developers.com/index.php?pagename=BlueangelASIC3
You can try to write in the appropriate registers
and look if it helps.

K-Jam locks at bootup

Hi, I bought a new K-Jam, which was fine until I installed the SOTI pocket controller.
From then on, the K-Jam locks at boot (blue screen with I-mate logo on it), and the backlight goes out, coming back up after a few minutes. All the buttons do not work, and the device does not load its software.
I tried a soft reboot and a hard reboot, but nothing works can anybody help?
has you verified SOTI pocket controller is WM5 compatible ?
I think you must make an "hard-reset" :?
regards
AlexSim said:
Hi, I bought a new K-Jam, which was fine until I installed the SOTI pocket controller.
From then on, the K-Jam locks at boot (blue screen with I-mate logo on it), and the backlight goes out, coming back up after a few minutes. All the buttons do not work, and the device does not load its software.
I tried a soft reboot and a hard reboot, but nothing works can anybody help?
Click to expand...
Click to collapse
same probleem here....
how can i stop auto start of the soti software
soti version 5.05
Do a hard-reset, that's the only way I think.

Help.. .Killed my Qtek... PC BSD durning ROM Update

So, I have updated my ROM many a time, and was updating my qtek wizard with the 2.17 WWE rom, at 3% through, my PC does a Blue Screen of death... Now my wizard is just locked at the Color Bar screen saying IPL 2.17 and SPL 2.17.
DID I KILL IT?
sdattilo said:
So, I have updated my ROM many a time, and was updating my qtek wizard with the 2.17 WWE rom, at 3% through, my PC does a Blue Screen of death... Now my wizard is just locked at the Color Bar screen saying IPL 2.17 and SPL 2.17.
DID I KILL IT?
Click to expand...
Click to collapse
No you didn't kill it. =)
Take the battery out, and put it back in.
Hold down the Camera button while pressing the power button
You should be back to the three color bar screen
Connect to your PC using the USB cable
Run ROM upgrade
That should fix it. Make sure you don't have anything running on your PC during the upgrade. The only time I've ever bluescreened during a ROM upgrade is when I was playing MP3s in the background.
summiter said:
sdattilo said:
So, I have updated my ROM many a time, and was updating my qtek wizard with the 2.17 WWE rom, at 3% through, my PC does a Blue Screen of death... Now my wizard is just locked at the Color Bar screen saying IPL 2.17 and SPL 2.17.
DID I KILL IT?
Click to expand...
Click to collapse
No you didn't kill it. =)
Take the battery out, and put it back in.
Hold down the Camera button while pressing the power button
You should be back to the three color bar screen
Connect to your PC using the USB cable
Run ROM upgrade
That should fix it. Make sure you don't have anything running on your PC during the upgrade. The only time I've ever bluescreened during a ROM upgrade is when I was playing MP3s in the background.
Click to expand...
Click to collapse
Exactly this solution works fine with me!
three color bars on tmobile MDA
Hi,
I tried a hard reset with pressing camera button and power button together but it comes on with a three color bars
RRU
IPL 1.01
SPL 2.26
USB
But while flashing new ROM it says there is a connection problem with the PDA and yes, it does not show connected on Active Snyc 4.5...
Any help how to flush it with any ROM. I also tried to download the Tmobile software but it agains says the phone is not connected with USB.
When I connect the phone wiht USB, computer makes beep like somthing is connected....I can not figureout what is wrong.....any help???
thnx

how to prevent power on when sliding out?

Hi folks,
does somebody know how I can prevent my kaiser (t-mobile vario III) from powering on when the keyboard slides out? This happens a lot when it is in the pocket of my trousers....
thanks
Werner
... to use a case...
ok, but thats near removing the battery before putting it in the pocket...
first press and hold the hang-up button so that it locks. Then just push the power button once. This puts it in standby. Then just configure the standby timeout when not on external power, and you're set.
how is it about aktivating the lock function?
infernix said:
first press and hold the hang-up button so that it locks. Then just push the power button once. This puts it in standby. Then just configure the standby timeout when not on external power, and you're set.
Click to expand...
Click to collapse
When I hold the hang-up button my phone doesn't lock.
Holding hang-up button ("red phone" key) does lock the unbranded, HTC Kaiser. Dunno about Tilt or other branded phone
the vpa device of kaiser with german rom doesnt have this problem i read in ppc-world forums. so its just a reg key or a cab installed at branding. so lets get a solution
Holding the red phone end key on the Tilt simply ends your data connection.
spartanrob said:
Holding the red phone end key on the Tilt simply ends your data connection.
Click to expand...
Click to collapse
and on the HTC branded Kaiser, it locks the device and does NOT end the data connection .. so I tend to agree, there must be some registry setting to change this.
On the MDA Vario III holding the red button for a few secs ends the data connection, a few secs longer locks the device. best of both worlds I guess.

Htc Diamond bricked black screen

hi ,all, i ve the follow problem, my diamond after the normal use and reboot, was bricked in black screen.. when i power on the diamond the backlight of display turn on, but no displayed any image or caracter.. after 30-40 seconds the back light turn off, and when i push a power button the light turn on.. if i push the volume button the phone beep beep.. i ve tried to put in boot loader and seems that is possible but the phone not recognized from active sync i ve tried to reload a rom, hard spl, and radio rom, but ever i ve econnection error..
can anyone help me? after that i ve read manu post i think that the problem is defect in motherboard, but i hope that is not...
sorry for my bad english , but i am Italian...
thank in advance..
Regards
Jetway

Categories

Resources