i have a big problem. I tryed to install Xda_IIs_v131139_upgrade and then the message error shows :'' error 114 : radio rom update error ''
after that screen shows : serial and at bottom v2.07. i tryed to install again but the same problem shows up
What can i do ? xda iis is from UK ( O2) !!!!!!!!
i also have card reader and 1gb sd card if that helps to fix my problem
i have a big problem. I tryed to install Xda_IIs_v131139_upg
u have to edit the "RUU.conf "open it with notepal & add in "[CHECKCEID_TYPE]=1 " after the "[RADIO_FLAG]=1".
i have a big problem. I tryed to install Xda_IIs_v131139_upg
u have to edit the "RUU.conf "open it with notepal & add in "[CHECKCEID_TYPE]=1 " after the "[RADIO_FLAG]=1".
I have the exact same problem on a SX66. Added [CHECKCEID_TYPE]=1 like you said and still have the problem. During the update there is a long pause at 1% then it goes up somewhat quickly, skips 10% goes right to 11 and then to 12%, long pause and then the 114 error. I've tried many different radio files and get the same on all of them.
Related
Help!!!!
I am following the instructions for the upgrade to WM2005 from this location: http://wiki.xda-developers.com/index.php?pagename=BA_5.1.1700_build_14343_Upgrade however I am at this stage
When you are done, remove your device from the cradle.
Press Power + Softreset, and when the colored stripes (well, this is the bootscreen )shows on the screen.
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc.
* Quickly press Record+Camera before the versions appears at bottom right
* OR, press Power+Softreset+Camera+Record at the same time.
I can not get the 3 options to come up on the screen and I'm just left with the device showing the coloured stripes.
Can anyone give anymore advise??
My device data is as follows prior to update PH20B 0 BENG G T-MOB005 1.06.00 0 0 1.06.160 1.10.00 10.00
hoping for good news
Mark
Decided to go back!!
Hi
Decided it would be best to go back to old version.
Ran the Official MDA update which changed the radio, ex rom and rom back
However on hard reset none of the extended rom is loaded. Ran the extended rom unlocker. I can see cabs in the extended rom but am unable to copy any of them, if i click on unlock i get the following error.
ERROR:
FL_IOCTL_BDTL_HW_PROTECTION - A device attached to the system is not functioning.
Is this because I did this in the attempted upgrade to 2005?
Setup the Storage size to get a full 60MB and not 43 MB
* Copy Repart_DOC.exe from the "Preparation\DOC repartitioning tool" folder to your device and launch it.
* Set size of Extended ROM to 128 kb
I set it to 128 as suggested, do i need to run this again but change the value???
Any help would be great
Thanks
Most extended roms are 16mb+, so I recommend instead of 128kb, i put it to 16000kb ;-) = 16mb or known as like 15.58mb
If you reset, press AND HOLD the camera and record button, then you will get the 3 options.
you can navigate through them with the record (down) and camera (select) buttons. if your done you can press mail, to "save".
Sorted
Thanks everyone for the advise.
I could not get the 3 options no matter how hard I tried. I then reflashed with the origional T-Mobile rom radio and extend rom.
I just could go without WM2005 so i tried again, flashed and hey presto the options appeared!!!.
The only thing I can think of and that should be added to the tutorial is to reboot after installing ActiveSync V4 as this was on the only difference, flashed 3 times with WM2005 before reboot and no joy yet after PC reboot all worked first time!
Just some feedback
Mark
Guys,
This is my experience with O2, which stuck on boot after udated to new IVAN's ROM.
First of all I'd like to thank Ivan for his great job.
Now, what I did:
Downgraded to se2003
Unhide, Unlocked EXTROM
Repartition EXTROM to 8MB
Upgraded to new WM5 ROM
Reboot -> STUCK !
I found the solution which worked for me and may be will help you too.
More, after my second attempt to upgrade ROM, my Laptop rebooted itself a 47% ! I did panic- my device was gone dead!
even Bootloader mode was unavailable.
OK, I disconnected PDA from cradle, removed battery and left it for 10 minutes. Then I put battery back, and was able to put it into bootloader mode.
Then, I run mtty utility and typed in "set 14 0" I'm not sure why and how, but it allowed me to to go to bootloader mode.
-I set SE2003 OS
-I repartition EXTROM to 16MB
-Updated again to new Ivan's WM5.
Voila ! it's OK now. I'm installing all needed CAB's and now have clean very fast and working OK WM5 OS o my O2 XDAs PDA.
( although have not tryed yet BT and WiFi)
I'm afraid the problem was due to setting number 8000 KB in partiotion tool set it actually a bit less something about 79xx KB.
May be EXTROM for Ivan's ROM did not like it and failed to boot. But this is just a speculations, I'm not sure. I should perhaps set size o EXTROM to say 9000KB and try again, but simply did not have a time to do test.
Nevetheless, I'm happy now.
can u provide me step by step (noob guide) to downgrade back to wm2003se ... the one i downloaded from the official site doesn't work ... it will say error and i still stuck with wm5 ... im a noob ... please really help, thanks
ok at last i found it ... extract the installation files provided by o2 ... put the rom file into the downgrade folder provide by the modified rom pack ... now i try go back to wm5 ... wish me luck
i tried go back to win2003se but when i use the unlocker tools it failed ... so i guess i will nvr get to see the ext rom ... anyway as long as the phone can be use i will leave it as it is now
Yes, I know, it gives you an error message (something about wrong parameters) on unlock. But, under that you can see another message box with unlock OK message. Quite weird.
Steps I took to downgrade are exactelly as instructions in downgrade folder.
And one more thing I forgot ! After unhiding I did soft-reset, then unlocked and then Formatted ETROM folder before upgrading to WM5.
COM said:
And one more thing I forgot ! After unhiding I did soft-reset, then unlocked and then Formatted ETROM folder before upgrading to WM5.
Click to expand...
Click to collapse
maybe that's why u able to see the extrom after upgraded to wm5 ... btw i install the cabs one by one and now my wm5 worked ... guess imnot going to touch it anymore, but the performance is actually quite slow ... do you actually install all the cabs into the device, storage card, or extrom partition (i dont have this) ... to maximise the performance?
what WM5 are you using?
if you ask me, i'm using Ivan's ROM + radio 15.0 with about 10 diff. cabs installed.
performance is not such impressive, but everything is working and I do not have soft I won't use.
clean and quite reliable, but speed is slow.
COM -
I also got stuck with a white screen after flashing ArtZ Rom and doing a hard reset.
Just a white screen and nothing happens.
Flashed other Roms - back to Tuma - same thing - white screen after hard rebooting.
Stuck and confused now.
Any ideas for a solution?
Thnx
OK - I am back.
Panic mode over - whew!
Flashed back to WM2003 from i-mate site - it worked.
Then flashed to latest ArtZ Rom.
Don't really know what happened or why. I've upgraded to nearly every WM5 Rom with no problems. suspecting the partitioning of extrom?
hasanj4 said:
OK - I am back.
Panic mode over - whew!
Flashed back to WM2003 from i-mate site - it worked.
Then flashed to latest ArtZ Rom.
Don't really know what happened or why. I've upgraded to nearly every WM5 Rom with no problems. suspecting the partitioning of extrom?
Click to expand...
Click to collapse
I am still in the same problems. I can't downgrade to
Windows SE2003, becouse of error 113: "Extended ROM
Update Error". Stucked in white screen and, after reset
at 3 stripe-colored-screen.
Does anybody know the solution for this issue ?
Thank you in advance.
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
Click to expand...
Click to collapse
---
imatrix, thank you very much, your hint solved
this issue with stucked boot screen and Extended
ROM Error when downgrading to SE2003.
I already tried with mtty and "SET 14 0", but
don't know for the other commands / task 28, task 0.
The main hint is "task 28" which made DOC_format_HW+
DOCInfoTableinitHW+ other formatting.
Again, thank you very much and all the best to you.
Greetings from Croatia, the small land for a great vaccation ;-)
@MDA3_CRO
Just saw your post.
Could not get mtty to work.
Will keep your instruction for future use (hope not).
Glad your .paper weight' is useful now
Please help I have tried all the above and none of it has worked, I'm still stuck in bootloader screen.
i dont understand what you mean by
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
when i run my mtty it just opens "Open Port Settings" then it goes to a window that shows i can type in it but it only allows me to copy paste words into it. Can anyone help me please?! i just want to be able to use my BA again
hi people...
i tried to install a wm5 and a wm6 rom in a qtek 9090 but i can't format and merge ExtRom... i tried to use the rom unlocker found in the a77ila wm5 rom pack but i have a lot of error during unlock.. and when i try to format this error will show: FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed!
i tried with xda-developer unlocker but an unable to find exe file will show..
and repart_doc still not work...
anyone can help me?
my device:
qtek 9090
SO WM2003SE ver. 4.21.1088 (Build 15045.2.6.0)
ROM : 1.40.04ITA
Radio: 1.12.00
Prot Ver: 1337.42
ExtRom ver: 1.40.153 ITA
tnx in advance... and sorry for my bad english
1. You cannot reformat extROM without unhiding and unlocking it first. Follow the procedure step by step. (remeber aboutsoft reset
2. Correct links to both tools as well as the procedure you can find on Wiki (http://wiki.xda-developers.com/index.php?pagename=Helmi - Installation)
3. Report effects.
3b. Your english is OK
here i am...
followed tutorial step by step...
1. installed the unlocker
2. launched unhide
3. soft reset
4. launched unlock
5. system displays a windows named debug showin ERROR: press OK
6.another system window named debug showin FL_IOCTL_BDTL_HW_PROTECTION press ok
7. another window saying a peripheral connected to system in not working press ok
8. a debug window saying extrom unlocked
9. soft reset
10. launched repart_doc
11. error window saying "FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed" press ok
tried also without soft reset at point 9. same results..
i only see Ext_Rom in memory page of Setting but still remain full
------------------------------------------------------------------
Finally solved...
i don't know why but ita extrom can't be formatted...
so i used an escamotage... upgraded qtek9090 with this rom BA_TMNL_14200_119_11300_Ship
After used unlocker and repart_Doc and all goes on....
now go to upgrade to HELMI_BA_WM6_R0_Public
hiya
i cannot format my DOC too, i got the same error ,
i used TASK 28 under MTTY , but still i'm getting this error.
anyone can help with this problem ?
Hiya
I was searching XDA-DEVELOPERS website about 2 days to find a solution for this problem, I have an I-mate PDA2K, i used all EXTROM tools on this website like this:
1- Installed EXTROM_tools,
2- run UNHIDE ,
3- then run UNHIDE,
4- Soft Reset,
5- now i can see Extended_ROM on my file explorer, i can read it , and able to write on it ... copy paste ...
6- run REPART_DOC.exe on my device,
7- tried many sizes like 128kb, 1024, 2048, 512, 61000, .................
but on this step i always get the god damned FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed,
i finally used Task 28 under MTTY but nothing happened, still have this problem,
No Wayyyyyy ! No wayyyyyyyyyy to repart my DOC size, .... noooooooooooo wayyyyyyyyyyyyyyyy
anyone going to help me plzzzzzzzzzzz ?
try it in this order...
1. downgrade to 2003
2. in WM2003 unlock... unhide... softreset
3. then repart_doc...
4. then upgrade to WM5/WM6
PS:
@Borbor...
hmm... i cannot see any part on your post that you tried to UNLOCK the extrom.
mastermoon DID. you need to unlock it first in order to modify it.
unhiding it just simply makes it visible to filemanagers.
SilverSamurai said:
try it in this order...
1. downgrade to 2003
2. in WM2003 unlock... unhide... softreset
3. then repart_doc...
4. then upgrade to WM5/WM6
PS:
@Borbor...
hmm... i cannot see any part on your post that you tried to UNLOCK the extrom.
mastermoon DID. you need to unlock it first in order to modify it.
unhiding it just simply makes it visible to filemanagers.
Click to expand...
Click to collapse
Hiya
I'm not a braincracked one, I'm a computer software engineer and i write CNC machines programs, so i don't need to someone to teach me instructions !!!! i did all, but i got FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed. !
find me a good solution plz !
and i thought landmark's the only one who is bossy...
if you dont need instructions then what are you looking for in here??? duh!!!
you're both at the same level of intelligence... are we downgrading humans now?
P.S.
look at the end of the third post... that is solved.
Everybody is allowed to name themself software engineers nowadays?
Please people start behaving like grown up's we are no longer in kindergarten.
Please:
- listen to each other
- be prepared to be wrong
- try explaining your problem in another way
- but most of all don't try to solve your listening problems by yelling and cussing to each other.
TIA, Flar
I'm dizzy reading all the threads, information overload, so thought I'd just post the question! This is all a bit scary and I'm a complete newbie so take it easy on me... and feel free to dumb everything down as if I were a child.
I live in Australia and have a Treo 750 with Software Version TREO750-1.15-ROW. It seems to be unlocked but still has the Telstra splash screen, although I use it with Vodafone. I want to upgrade to WM6, and from what I can tell I should upgrade using Treo750_2_27_ROW_EN_DesktopUpdater.zip (which I now have). Is this right? Should I skip straight to the WM6.1 upgrade? Are these official/safe?
I am running 32-bit Vista with SP1 on my laptop.
I found instructions on Palm's site here:
http://www.palm.com/au/support/treo750/downloads/wm6update.html
Are those the instructions I should follow? Is that all I need to do? I keep seeing references to the "Bootloader Method" or the "SD Card Method" or the "Cheetah Method". What are all these alternative methods? Which are the advantages of each? I've seen various different instructions, some involving renaming some .nbh file, etc. What is the definitive method?
I saw the sticky thread for the "Cheetah Hard-SPL and SIM Unlocker"... what is that utility for? Are the instructions for it in the download itself? (I didn't see it in the thread) What are "cooked" ROMs and why should I be interested? Where can I find them?
Sorry for the newbieness... thanks so much to all who respond!
upgrade to WM6
If you want to upgrade to the official palm WM6 rom - then you use Treo750_2_27_ROW_EN_DesktopUpdater.zip and it is very simple - just connect the PPC to your computer . (as I know better to do it with a computer with WINXP and Activesync) , then run the program in the file Treo750_2_27_ROW_EN_DesktopUpdater.zip, and that's it.
If you want to upgrade to other roms like 6.1 normal or lite that you can find in this forum - then you need the other methods (there are two as I know - bootloader method or Kaizer..somthing method). Well, I wrote a guide how to upgrade to WM 6.1 lite using the bootloader method , I just sum up from this forum :
1. Download the rom file and the radio file:
Rom file from here : http://rapidshare.com/files/89355384/Treo750_WM6.1_WWE_Lite.rar
The radio file from here :
http://rapidshare.com/files/89336971/Treo750Radio1.54.07.00.rar
2. Download the Hard-SPL from here :
ftp://xda:[email protected]/Cheetah/Unlocker/CheetahUnlocker.rar
3. Format mini SD card 32 FAT , using a card reader or other way.
4. Do a HARD-SPL with the CheetahUnlocker file ( step 2) . Connect the Treo with your computer using Active sync(for WINXP) and run the file. Use those steps:
- Click the Step 1.... wait the progress bar reach 100%
- Now watch the Screen on your PDA it will launch 2 times verification...
- just click YES ...wait.. and YES again.
- after finisih... wait until the activesync go green again.....
- Now click the Step 2... wait the progress bar reach 100%
- Watch the screen again... same thing.. it will launch 2 times verification.
- click YES ...wait.. and YES again.
- After finish it your PC screen will shows some popup. ignore the reading bla bla bla... about ask u to click ok.
- Just wait untill your activesync go green again.
- Now click that bloody Popup OK button.
- The unlocker app will shows up again..
- Then you will see errors saying.. continue, cancel...etc... bla bla... just click continue.. error message.. iqnore it and then just finish it.
- Now your Cheetah should be on HARD SPL mode.
5. Install the ROM :
a. Using Winrar get the file from step 1. It's name should be : CHEEIMG.nbh
b. Copy the file to the root of the mini SD .
c. Do BOOTLOADER:
1. turn phone on
2. press the MEDIA button AND at the same time with the stylus the RESET PIN
the MEDIA button is the 3rd button on the left side of the phone, under the volume button
the RESET PIN is under the MINI SD card cover
3. keep holding the MEDIA button (left side of phone) until you get the 3 color screen
Wait until it finishes. Then Hard reset the device when prompted. To hard-reset, hold the End key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
6. Flash the radio at the same way – just copy the radio file to the mini Sd – it should be the same name. (CHEEIMG.nbh ) .
7. Download the Palm SMS file from hereYou need it only for the lite version)
http://rapidshare.com/files/99335294/threadedsms.rar
or
http://www.megaupload.com/?d=H63TXUP4
And install it as regular software (Copy to the mini SD and run it from the Treo.)
And that it all !!
Do not restore from your backup (You can restore only your data files).
Good luck !!
Update Successful
Thanks mate, I'm not brave enough to try the wm6.1 upgrade yet, but I did manage to upgrade to wm6 with the Updater, even though my device was "not supported". I ended up using the method where you edit the payloads.xml file before clicking 'start' so that it accepts your current device version, etc. I'm all good now.
libal said:
If you want to upgrade to the official palm WM6 rom - then you use Treo750_2_27_ROW_EN_DesktopUpdater.zip and it is very simple - just connect the PPC to your computer . (as I know better to do it with a computer with WINXP and Activesync) , then run the program in the file Treo750_2_27_ROW_EN_DesktopUpdater.zip, and that's it.
If you want to upgrade to other roms like 6.1 normal or lite that you can find in this forum - then you need the other methods (there are two as I know - bootloader method or Kaizer..somthing method). Well, I wrote a guide how to upgrade to WM 6.1 lite using the bootloader method , I just sum up from this forum :
1. Download the rom file and the radio file:
Rom file from here : http://rapidshare.com/files/89355384/Treo750_WM6.1_WWE_Lite.rar
The radio file from here :
http://rapidshare.com/files/89336971/Treo750Radio1.54.07.00.rar
2. Download the Hard-SPL from here :
ftp://xda:[email protected]/Cheetah/Unlocker/CheetahUnlocker.rar
3. Format mini SD card 32 FAT , using a card reader or other way.
4. Do a HARD-SPL with the CheetahUnlocker file ( step 2) . Connect the Treo with your computer using Active sync(for WINXP) and run the file. Use those steps:
- Click the Step 1.... wait the progress bar reach 100%
- Now watch the Screen on your PDA it will launch 2 times verification...
- just click YES ...wait.. and YES again.
- after finisih... wait until the activesync go green again.....
- Now click the Step 2... wait the progress bar reach 100%
- Watch the screen again... same thing.. it will launch 2 times verification.
- click YES ...wait.. and YES again.
- After finish it your PC screen will shows some popup. ignore the reading bla bla bla... about ask u to click ok.
- Just wait untill your activesync go green again.
- Now click that bloody Popup OK button.
- The unlocker app will shows up again..
- Then you will see errors saying.. continue, cancel...etc... bla bla... just click continue.. error message.. iqnore it and then just finish it.
- Now your Cheetah should be on HARD SPL mode.
5. Install the ROM :
a. Using Winrar get the file from step 1. It's name should be : CHEEIMG.nbh
b. Copy the file to the root of the mini SD .
c. Do BOOTLOADER:
1. turn phone on
2. press the MEDIA button AND at the same time with the stylus the RESET PIN
the MEDIA button is the 3rd button on the left side of the phone, under the volume button
the RESET PIN is under the MINI SD card cover
3. keep holding the MEDIA button (left side of phone) until you get the 3 color screen
Wait until it finishes. Then Hard reset the device when prompted. To hard-reset, hold the End key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
6. Flash the radio at the same way – just copy the radio file to the mini Sd – it should be the same name. (CHEEIMG.nbh ) .
7. Download the Palm SMS file from hereYou need it only for the lite version)
http://rapidshare.com/files/99335294/threadedsms.rar
or
http://www.megaupload.com/?d=H63TXUP4
And install it as regular software (Copy to the mini SD and run it from the Treo.)
And that it all !!
Do not restore from your backup (You can restore only your data files).
Good luck !!
Click to expand...
Click to collapse
Did everything - step by step but nothing!
still the color screen with the word serial in the bottom!
What is wrong ???
Thanks in advance,
Nir
Got it!!
Turned out vista is displaying fat32 file system no matter what the file system is...
Nir
WM 6.1 Upgrade
Can anyone tell me where the AT&T Upgrade for the Treo 750 is to version 6.1. I have seen many different posts here that show many different links and different downloads with different loading instructions. Is there anything out there that is clear? I am willing to give it a try, but I am not exactly sure of which download to try. Thanks for your help.
i have a dell streak 7(tmobil) , android version 2.2 ,
it pop up a message all the time : system exception. Quit or copy log to sd card or report by LOTA , and after clic on Quit a message says : sorry! the application has stopped unexpectedly.please try again (force close).
here is what i tried :
- factory data reset , but nothing problem still and even the old accounts still exist wont erased after this reset.
- system update , i tried to update the system by download and install but it keeps downloading for a few mints (70%) then it disconnect from the wifi connection and it wont connected again till i reset the device one more time.
please see what you can do for me to resolve this problem, i dont need any info to be recovered i just want it to work nice again.
i attached some picts for the errors message.
thanks.