Database Develop

Soltuion: When you don't hear Calls

When you don't hear your calls and infact your call is in progress, this occurs normally in the morning when your unit take a nap in the night.
The solution is turn ON your bluetooth and then turn it OFF or just remain it to ON.
This problems occurs frequently who use bluetooth headsets.

I don't use any bluetooth headset and I still have this issue... can't ear anything...
So you say that your solution is valid? Great! I'll give it a try!!

anyone tried?
it works??

!Working! Solution
Remove BTTrayCE.lnk from Windows\StartUp, and the sound problem is solved.
To enable BT again, run Run_BTTrayCE_10.lnk and BT icon will appear.
To disable it again, u have to soft reset the machine.
Cheers,
Senator

THIS WORS FINE. I HAVE THAT SYSTEM WORKING IN MY 9090, FOR 2 MONTHS ALMOST AND THE PROBLEM GONES.
REGARDS

BY THE WAY, I FOUND THIS PROGRAM THAT IS THE SAME OF WINDOWS XP TASK MANAGER, TO POCKET PC, THAT ENABLE YOU TO END THE PROCESS WITHOUT RESET.

Please can someone give a solution for this "no hearing the caller" problem!!!! Otherwise I can't use my qtek 9090. Everytime to switch the BT on and off isn't real solution.

My solution works...

yes but is that a real solution. I mean it' s not a real automatically solution. everytime I want to use BT I have to start it. is a radio update to 113 no solution?

Haven't updated yet, try it.

Disconnect Bluetooth after call

Hello,
I searched a program for my Kaiser that disconnects a BT device, such as carkit or headset, when a call is finished.
With disconnecting I mean that the device is not connected anymore at that moment.
So when I have an incoming phonecall, I have to push to connect my BT device to my phone. Then I can pick up the phone with my device.
Who knows were I can find this?
Thanks,
Temba

Hmm, I don't see the point.
When an incoming call is received, before it starts ringing the Kaiser will look for a known paired BT device, if it is on but not connected it will connect it automatically. If it's not on at that moment you're out of luck for that call.
Just leave your device connected... you should already have to push on your device to take the call, no?

Kilrah,
The point is that when I end a call, I want that my BT device disconnects from my phone. Reason is that when I walk to my car, I want to use my BT carkit and not my headset.
Maybe I had to ask how I can unpair a BT device from my phone after a call. But 'unpairing' is for me that I have to enter a pincode every time I want to connect.
Any ideas?
Temba

Hi,
This is an issue between HTC Windows Mobilie devices and carkits equiped with a parrot chip.
As far as I've understood all Windows Mobile 6.1 devices are affected.
I myself have a Kenwood DNX 8220 BT Double DIN Head Unit in the car but there are more Head Units and carkits that make use of the Parrot chip CK5050 if I'm not mistaken.
Does anyone have a tweak or a registry setting that is able to fix this?
I've allready tried to change the COD registry value to: 52020C which is suggested as a solution in a parrot forum topic:
http://www.parrot.com/forums/english/viewtopic.php?id=5620
It didn't solve the issue

tembares said:
Kilrah,
The point is that when I end a call, I want that my BT device disconnects from my phone. Reason is that when I walk to my car, I want to use my BT carkit and not my headset.
Click to expand...
Click to collapse
Oops, had missed this reply back then. I know it's way old, but as someone brought this thread up again, never know if you might read it...
AFAIK this isn't possible. If you have 2 BT devices, paired and powered on but not connected, when a call is received / placed form the phone it will use the last one that has been either connected or selected and "Set as hands free" in the BT settings. If you want to make sure the phone connects to one of them without you going in the BT settings and set it as hands free, you need to turn the other one off.

Diamond Bluetooth HeadSet Bug

Ok, not sure if anyone got the same problem as mine, but here is my problem:
I have a Diamond using AZTOR v7 Rom, radio vBS14 if that matters and Sony Ericsson DS205 as my headset. I start my bluetooth on my diamond and can pair up with the DS205 without any problem. I can also listen to music without lag and sound is also crystal and solid.
When there is a call kicks in, I can answer the call by pressing a button on my DS205..... However, the problem comes when I end my call, the headset will be disconnected afterward and I have to manually press a button on the DS205 to make it reconnect. Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?

I don't have this problem, but i have another problem, when i use the orignal rom, i can use my headset(jabra bt3030) in my diamond and it will automatically connect to use hands free and wireless stereo mode when i turn on bluetooth, so when i change to use swift 7.5 full rom, i have to resetting the bluetooth in diamond everytime when i close bluetooth

I can only get wireless stereo for my Plantronics Bluetooth Stereo headset. Any ideas why I can't get hands-free. Radio issue?
It was possible with some earlier ROM, but I can't remember which... (yes, I'm a flashing addict).

I'm having the same exact problem & it's annoying as hell. At this point, I can't get the bluetooth function on the phone to activate at all. I use the same bluetooth on another phone with no problems whatsoever, so I know it's the phone. I'm running the original rom.....not a flasher.

Have you tried Jetware?

Sorry, just installing this doesn't change anything. Still no hands-free.
Is there a specific option you want us to set?
shinji_lee said:
Have you tried Jetware?
Click to expand...
Click to collapse

lit2fly said:
... Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
Click to expand...
Click to collapse
Yes - I have a very similar problem with my jabra SP700. The Diamond 'forgets' the wireless bluetooth mode every time I disconnect the two devices (although the Stereo Bluetooth icon is still showing in the status bar).
For a short while I was having to re-pair the devices every time I got in the car - until I found the same workaround as you.
There must be a proper solution???

Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck

juanfervs said:
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
Click to expand...
Click to collapse
I have this value in COD key but I have the problem anyway.
Any solution to this annoying problem?

i use my diamond with my bluetooth handsfree kit in the car, it is classed on the phone as a headset though. the sound is ok, a bit echoey but ok. but the microphone doesnt seem to pick up my voice, i have to really shout for people to hear me, on my old Xda Orbit it worked fine. any ideas?

Pairing the Bluetooth with Jabrasp700?

Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.

Edris said:
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Click to expand...
Click to collapse
I have the same problem with my SP700 and my Tritton BT stereo headset.Phone calls work almost all the time through the SP700 speaker, but playing music or through the FM radio seems to be a problem. I can get them to pair up sometimes by only checking the Wireless Stereo box. It works for a few times, but then I have to delete and re-pair again.
I've searched for all over for answers, but nothing seems to be a permanent fix. It's very frustrating to use my devices for anything else but phone calls.

Just to add a bit of info, I do not have any problems with my old Motorola HS820. Of course, I'm not using SP700.
Hope that helps your troubleshooting.

I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal

Possible solution
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking

Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.

Edris said:
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Click to expand...
Click to collapse
Thanks! Nice App! Tried it with my Tritton BT stereo headset and it works! Had to install to my device instead of Storage card, then had to delete and re-pair, but it so far I can toggle between on and off Stereo Headphones without any problem. Will try on my SP700 shortly.
I attached the Cab if anyone else wants it.
Thank you!
Works with SP 700!!!!!

Mal Bridgeman said:
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Click to expand...
Click to collapse
When the software loads, follow the instructions, do not install with any of the microsoft wizards that pop up, it will install itself. I couldn't find anything that lists what changes that were made.

SP700 Firmware
FYI,
I too had the same issues and downloaded the sp700 firmware update. I thought the same thing about the drivers, but called Jabra and they told me the firmware update has the drivers embedded in it. When you start the install you cannot plug it in till it tells you to. After you plug it in it installs the drivers. But BEWARE I have not been able to complete the upgrade, it stopped halfway and bricked. I called support and they said there is nothing to do, but luckily I bought it from Costco and they returned it. So being not so bright I tried it again but on a different computer (thinking that there might be a conflict) and it didn't even load and bricked it again. So I returned it yet again. So then I gave up on Jabra support and found A2DP toggle. It works good enough, so I am leaving it at that....
Take Care
David
Tilt WM6.1

andrew-in-woking said:
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Click to expand...
Click to collapse
I have the exact problem that you are having with the new, Hyperdragon IV, ROM.
Is this A2DP Toggle really the only way - I mean what's the difference between pressing a button on my Kaiser to reconnect and pressing the button on the SP700 ??
I have tried using Mortscript as shown http://forum.xda-developers.com/showthread.php?t=382172&highlight=a2dp&page=2 Although I edited the end out because it kills the player after ending a call. This hasn't helped either
I am off to see if the same problems occur with my lady's N96. If not and no good solution can be found for this I may have got her a new present.
Aren't I nice ?!

Found another possible solution, it,s called zoA2DP. So far it works flawlessly between my SP700 & stereo headset without having to toggle anything or change any settings. When you install it, delete your original pairings and add them again, make sure that hands free & wireless stereo are checked in advanced options on you BT settings. I believe this is a registry mod, there are no icons or any noticeable applications running in the backround.
The thread is here
http://forum.xda-developers.com/showthread.php?t=279127
Cab file attached

No possibility of playing music by BT, is it fault mini or BT devices ??

As a topic, either by phone or through the BT handsfree I can not play voice, or the fault of poorly expanded the capabilities of the BT module if my periphery are to anything that may need some traps for this or something, who tried such a thing ?
- BT handset Samsung HM 1200
- Speakerphone B & M to Fiat
When the handset once I did it but I do not know how it happened , I had enabled navigation and command gave the speaker phone at the same time the phone was paired via BT with the handset and someone rang during the interview I heard the command of navigation on the handset and I was shock when the caller hung up , the remaining commands on them heard in the handset , but after reaching the place and disconnected set , the next day I could not already do it again , I tried to connect analogy , but it does not work , what strange now as I turn support BT navigation is silence , even as the inclusion of a music player that is inaudible music , that is, as if gave the voice on the headphones, but it did not exactly overwhelmed , and before it did ..... any clue ?

slon11 said:
As a topic, either by phone or through the BT handsfree I can not play voice, or the fault of poorly expanded the capabilities of the BT module if my periphery are to anything that may need some traps for this or something, who tried such a thing ?
- BT handset Samsung HM 1200
- Speakerphone B & M to Fiat
When the handset once I did it but I do not know how it happened , I had enabled navigation and command gave the speaker phone at the same time the phone was paired via BT with the handset and someone rang during the interview I heard the command of navigation on the handset and I was shock when the caller hung up , the remaining commands on them heard in the handset , but after reaching the place and disconnected set , the next day I could not already do it again , I tried to connect analogy , but it does not work , what strange now as I turn support BT navigation is silence , even as the inclusion of a music player that is inaudible music , that is, as if gave the voice on the headphones, but it did not exactly overwhelmed , and before it did ..... any clue ?
Click to expand...
Click to collapse
Hi! Can you elaborate your problem description more? If I got it right, you are trying to use a Bluetooth headset on your phone. Try to see the settings for your Bluetooth connection.

Headset is working i can talk but i would like listened music and have navigation command too, BT settings in Phone arę poor there isn't much to set, only connect with other devices and time to be visible at all
OK i found problem ,my headset hasen't A2DP it's nessery to transmit music and more .
TREAT CAN BE CLOSED