Hi everyone,
I got my new Kaiser (AT&T Tilt) last week, unlocked of course, and I have reformatted it yesterday, and since then, I am unable to get Wifi to connect to any network! The device shows me the available network and everything, but it says it's connecting to them and then it just says they're available
Any solutions? Suggestions?
-W.
TyTN X said:
Hi everyone,
I got my new Kaiser (AT&T Tilt) last week, unlocked of course, and I have reformatted it yesterday, and since then, I am unable to get Wifi to connect to any network! The device shows me the available network and everything, but it says it's connecting to them and then it just says they're available
Any solutions? Suggestions?
-W.
Click to expand...
Click to collapse
same here.... but no solutions yet....
What ROMS/Radios are you using?
Actually, a solution that would work is to power cycle the device (remove the battery for a few mins out of the device, put it back in, and run again) however, I am not sure about this solution as it may be a temporary one!
The ROM I have is:
1.57.502.2
Radio:
1.27.12.11
Any suggestions on the ROM/Radio?
-W.
just a suggestion of what works for me.......my POS router, i can only connect to it if the wifi power mode on the kaiser is set to best performance. same sh*t with the wizard and the hermes. i seriously should get a new router
i had the same issue. But today i triedd q-mobile rom, which has a different radio than before. It works now. I am finally connected to my router. I have a Tilt as well.
I've noticed variations in performance and willingness to connect to APs depending on the Radio version. On 1.27.12.32 it would sometimes connect, other times not - and take a long time! On 12.17 it connects pretty quickly to most APs. If it doesn't, I turn Wifi off, then on.
Actually, It used to connect to the same network (probably different AP) with no problems at all!
I encountered the same issue today, and even after a powercycle the same thing happened..
BiPolarXpress said:
i had the same issue. But today i triedd q-mobile rom, which has a different radio than before. It works now. I am finally connected to my router. I have a Tilt as well.
Click to expand...
Click to collapse
I had the same problems you guys had. tried to connect then would say available.
i took your advice. first i tried to install the radio that comes with the q-mobile. i couldnt install it to my phone, the screen would black out.
next i went ahead and installed the latest version of q mobile. now it works. and btw q mobile is one fast freaking rom! the screen goes from landscape to portrait in a flash!
thanks!
Mine abruptly started not connecting to any network as well. I'll try the powercycle idea. I have the AT&T standard ROM.
ranger47 said:
Mine abruptly started not connecting to any network as well. I'll try the powercycle idea. I have the AT&T standard ROM.
Click to expand...
Click to collapse
So if I powercycle it it works, except that when I try and connect to what wifi it works for a minute or so and then causes the same problems.
ok, need help with my wifi also, if I go to Wireless Lan settings it says LAN is off, and has a link to click to turn it on, I click it and it connects, shows info including signal strenth, then it disconnects.........it wont stay connected
jsnone1 said:
ok, need help with my wifi also, if I go to Wireless Lan settings it says LAN is off, and has a link to click to turn it on, I click it and it connects, shows info including signal strenth, then it disconnects.........it wont stay connected
Click to expand...
Click to collapse
I am facing the same problem. anyone help?
Hmm, sounds like the same problem I was having. See http://forum.xda-developers.com/showthread.php?t=366526
Not really a fix but a better workaround than having to reboot all of the time.
Wifi Problems with TyTn II
I have a HTC TyTn II and i have some problems with "wlan".
I cannot connect with my router.
I tried it even withouth a security key but it says connecting and for the rest nothing happens.
Ive resetted my router to default settings so everything is open but still i cannot connect my phone to the router.
My router brand is:SMCWBR14S-N2.
Details of my Phone:
Rom version: 1.56.404.6
Rom date: 08/28/07
Radio Version: 1.27.12.32
I hope you guys can help me, Thnx
Hi,SMCWBR14S n2 router the same problem for me but when i turn it to 802.b it works.
I think there is something in the mixed mode what the pda dont respect.
I have a similar problem, but with a twist.
When I'm at my parents, I can connect to their BT Homehub Wifi with no problems at all, even on power-saving wifi mode.
At my house, I have a Siemens Wifi router (from Tiascali), and I cannot connect to this (says it is available, shows signal strength, but won't successfully connect) unless I turn off the encryption/security key.
The only difference between the two networks (apart from the names) is the BTHomehub uses 64bit WEP key and the Siemens uses WPA-PSK key (AES/TKIP not specified in router setup page). I can change the key method on the Siemens to 64bit WEP, but it still won't connect. My laptop connects without problems to both networks.
Is this a problem with encryption handling by the Kaiser?
ROM: Dutty's WM6.1 WWE 29/04/08
Radio: 1.65.14.06 (tried the other radio version of Dutty's rom with same results)
Chris
edit: verfarkas, that's something I haven't trued yet - I'll give it a go when I get home tonight. That would be a nice simple fix - by default, my Siemens router has the "b" (and other suffixes) chosen automatically.
Change to best performance
I was having all of the above problems until I set my power save mode to "Best Performance". Go to settings -> Connections -> Wireless LAN
I have a Tilt with the stock AT&T ROM and HardSPL. I keep the HSDPA data on all the time and connect to my wireless access point while at home.
I understand and am fine with wifi disconnecting in sleep mode - email still checks using HSDPA. What normally happens is when I power the Tilt back from sleep the WiFi connects back to my access point.
I've noticed more than a few times however that coming out of sleep WiFi doesn't even attempt to reconnect to the access point. It is on in Comm Manager and appears to be associated with my AP, but checking the IP online shows an AT&T IP addr, not my CATV provider.
The only way to get back on WiFi is to shut off the phone (or reset). I don't want to keep WiFi on while in standby, I just want it to reconnect when it should.
Has anyone seen this behaviour?
Cheers,
Todd
Wifi access point problem
I had a problem where suddenly after months of use with my home wifi router, it suddenly would not connect with the router anymore. Would show that it was trying to connect, and then would suddenly not connect and try another router on the list.
I tried reseting and everything. Tried re-entering the password for my router as I thought that was the problem. finally the only fix i found to work was to actually delete the access point from the phone... then reset and then let it find it all over again from scratch. And miraculously that time it worked.
I know this is not exactly your problem, but hope it helps.
I will try that and see what happens. It seems whatever sub-routine that turns the wifi on isn't running at times and doesn't even attempt to search.
When im home, i like the phone to stay on Wifi at all times. It won't do this even if i have the thing configured to stay on while in sleep, so It drops the connection after a while. When i wake the N1 it won't connect automaticly. I have to turn wifi off and on to get it to connect. Quite annoying.
Should i reflash Cyan rom or get a different Kernel or do someone have an easy solution to the problem?
Thanks in advance..
Hi my wifi turns on but it never connects to my any network and it can't find any new ones
Solution annybody?
did you try full wipe?
Fixed it by Pressing Forgett all networks
Hello to all,
my Sony Z3 Compact / D5803
5.1.1
23.4.A.1.264
No Root
Reset with original settings
No stamina mode enabled
No enabled energy savings
No program installed unless the original ones after reset
The problem:
wifi connected everything works perfectly ... the phone goes into standby ... I move to another place where it previously was connected in wifi ...
any program that requires connection work ... if the phone comes out of the standby icon appears and wireless wifi back to work ...
So long as I do not go out of standby I do not receive any notification from the Internet because the wireless (having the correct WPA parameters) is not working...why ?!?
I tried different types of routers, various keys WPA / WEP ... if I do not force the exit from standby no connection.
Thank you so much for your advice, gino