Mda vario to qtek9100/k-jam i-mate - 8125, K-JAM, P4300, MDA Vario Software Upgrading

hi guys,
i have a t mobile mda vario (netherlands) but i want to upgrade to a qtek 9100 or k-jam i-mate rom how do i do it ?
regards from Netherlands

Re: Mda vario to qtek9100/k-jam i-mate/ instructions
uncx said:
hi guys,
i have a t mobile mda vario (netherlands) but i want to upgrade to a qtek 9100 or k-jam i-mate rom how do i do it ?
regards from Netherlands
Click to expand...
Click to collapse
Try this:
First download lokiwiz v2b. Don't use previous versions or you'll not get through this!!
Hard reset your device (not necessary, but it ensures you'll have no hassle with Activesync).
Done that? Good. Extract the lokiwiz v2b .zip folder and copy enablerapi.cab to your memory card or to 'My Documents' folder on your device. Then execute the 'enablerapi.cab'.
Done? Just switch off the device (power button; put it in standby mode).
If you have Activesync already installed, un-install it and re-install directly afterwards (ensure a brand new partnership).
Then when prompted by Activesync, plug in your USB cable PC-PPC and it should recognise as usual.
Then execute the lokiwiz.bat file (in the folder that was generated earlier when you extracted the lokiwiz02b.zip file) and when you see the MS Dos (black screen) choose the option CID Unlock (SuperCID) and wait for it to COMPLETELY finish. You'll know it's finished when your Wizard is re-booting. Plug out your USB cable at this stage.
Once re-booted and back into WM5, re-connect your cable and if all goes well it should re-connect to Active Sync (wait till it has finished syncing or says connected!).
Finally......double click the executable file, which should be:
RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe
Hopefully it will now install the ROM without hiccups (about 10 minutes).
Hope this helps. let us know how you get on.

Related

Qtek 9090 would not update and is dead now

Hi,
i tryed updating the qtek 9090, after i changed the country id type 1 it started.
It controlled my device and said : update from 1.12 to 1.40 and all the specs.
Then i hit next and id says checking information. It saysthat about 30 minutes now and the active sync connection is lost. Also my qtek looks dead.
I tried the installer again but it wouldn't work
I did a soft-reset and that didn't work also.
What now ? Hard-reset or ?.....
Thanks dudes
Ok, after a hard reset my device shows USB v 2.03 again so that's good ins't it
Now the country id error keeps coming, type is at 1 so what can i do more ?
Hi ThEScReW,
I've had the same problem while trying to downgrade to 1.22GER after flashing my device to 1.40WWE. I found out the modified version of MAupgradeUT that normally works for the Magician was able to flash my device with any BA rom I tried. It doesn't matter whether it's a type I or type II rom. Follow my instructions in the readme.txt and it should work.
Good luck!!!
Ok, i'm real thanks for that but i'm also really not that smart if you think i am.
What should i do with al those files? What to put where and what to do first and what last ?
Thanks :lol: you will be a great help
Where do you live btw in germany ?
Take the 1.40_shipped.exe you have and use winrar to unzip the files in a folder. After that you can copy the 3 .nbf files (nk.nbf, ms_.nbf and radio_.nbf)into the BA_upgrade no more errors folder. Then you start the MAUpgradeUT.exe. If the software says there is an error just press quit and restart the MAUpgradeUT.exe. Next time you try it should work making no problems.
Ps: I live in Bavaria about 50 km away from Munich.
berni_1980 said:
Take the 1.40_shipped.exe you have and use winrar to unzip the files in a folder. After that you can copy the 3 .nbf files (nk.nbf, ms_.nbf and radio_.nbf)into the BA_upgrade no more errors folder. Then you start the MAUpgradeUT.exe. If the software says there is an error just press quit and restart the MAUpgradeUT.exe. Next time you try it should work making no problems.
Ps: I live in Bavaria about 50 km away from Munich.
Click to expand...
Click to collapse
Ok thanks but the roms i have are just 1 exe file and that's an installer. It's as easy as hell. I just have to run de exe and follow the rules on the screen.
If i do what you tell me to do, then i need to download a rom from the ftp with al the files in. Then what do i do with those files? what first, what next , ..... :roll:
When using winrar you can extract all the files of your exe into one folder.
(Right click the exe and under options use "copy all files into folder"
Then take the 3 .nbf files and copy them into the folder with my files. Then start the MAupgradeUT.exe.
berni_1980 said:
When using winrar you can extract all the files of your exe into one folder.
(Right click the exe and under options use "copy all files into folder"
Then take the 3 .nbf files and copy them into the folder with my files. Then start the MAupgradeUT.exe.
Click to expand...
Click to collapse
Ok i'll try it tonight THX
Problem : if i use the rom from dangaard then the exe isn't a rar file, it's just an installer with everything in de exe ..
If i take a rom from the ftp and i unrar it then it are all CAB files and no .nbf files :roll:
Am i stupid or what? Witch version do i need and where do i get it? Maybe a link would do good :lol:
I'm really sorry for those questions, but here normally we just do the installer. I did allready a QTEK S100 and a QTEK 2020 with the installer from dangaard and everything worked fine. I just don't get it why i get the country id error now.
Try this one: ftp://ftp.xda-developers.com/BlueAngel/BlueAngel_Roms/BA_1.40_radio_1.20_untested_extrom/

Cannot unlock and unhid extended rom

I have a german Version MDA III
When I install the Programm for unhiding the system installs it int the folder "programme" and not into "programs" .
When I start it, there is an error massage.
When I create a new folder "programs" and copy the complete installed folder into it, there is again an error message.
So I cannot unlock and unhide and do the rest.
Can anybody help me, who already has installed WM% on a german MDA III ?
Thank you
Hi,
just try out the how-to I wrote together with Bubisch:
http://www.inntalinfo.de/apboard/thread.php?id=5817
(I hope you can read german?!)
I had a similar problem on my XDAIII, you'll need the "german_extended_rom_unlocker". You can download it on the tutorial.

9090 dead after flashing.....

My Qtek 9090 Dead after or in time flashing
I try .....
1. Flash with NO_ID
2.TRy via romupdate and nb1-file
3. Try via I-mate and T-mobile roms includes NO_iD
and nothing... only dark screen and USB or Serial string......
HELp plz.
...... and IF I insert in it SD card string serial no change after put him in cradle.....
What you can try.
if you have the seral message on your screen then just replace it in cradel and rerun the no_id application.
Are you SURE that you are using a valid ship.exe file and that you have extracted all the files and are following the upgrade instructions for 1.42 as per wilki.
MDAIIIUser said:
What you can try.
all THAT MAY BE
if you have the seral message on your screen then just replace it in cradel and rerun the no_id application.
Yes try, i start no_ID (with many roms) and 9090 waiting 20-30 minutes after this connection error
Are you SURE that you are using a valid ship.exe file and that you have extracted all the files and are following the upgrade instructions for 1.42 as per wilki.
Yes I extract all files , I try many ROMs for I-mate , Qtek , T-mobile in various version ..... I try make SD-Card with dump of rom,......
Only one that i cannot see How Update 9090 from SD to ROM or how copy dump of the ROM from harddrive via MTTY to 9090
This`is Unreal I work with PDA 3,5 years ago but look this bugs first ........
Click to expand...
Click to collapse
We have had a few (very few) that were not able to do an upgrade form thier pc. Not sure if this is a USB issue or software but after all the suggestions that we gave these people and none of them worked all they had to do was move over to a different pc and it worked.
So we know that the wiki 1.42 upgrade page works, that the file works and that the instructions are correct. Best for you is to try a different pc.

how to unbranded treo 750?

hi all,
i have a unlock treo 750 from cingular, pls its possible unbranded this and upgrade to rom 2.23 unbr?
thks for your time
Here's how you can unbrand your Palm Treo 750
moontger2 said:
hi all,
i have a unlock treo 750 from cingular, pls its possible unbranded this and upgrade to rom 2.23 unbr?
thks for your time
Click to expand...
Click to collapse
1. Make sure your Treo 750 is Hard-SPL (http://forum.xda-developers.com/showthread.php?t=334100). This would allow you to install any ROM, including cooked ROMs found in this forum.
2. Download the Generic Treo 750 WM6 ROM here: http://palmone.r3h.net/downloads.palm.com/Treo750_2_23_ROW_EN_DesktopUpdater.zip
3. Extract the updater into a folder of your choice. There are two levels of unpacking.
4. Search for the CHEEIMG_FW.nbh file in the final extracted folder.
5. Put the abovementioned ROM image file into a clean FAT32 formatted mini-SD card. Rename it to CHEEIMG.nbh.
6. Insert the now populated mini-SD card into the mini-SD card slot of the Treo 750.
7. Press and hold the side media button & at the same time, use the stylus to press the reset switch. You will see the tri-color bootloader screen momentarily followed by Loading...
8. Next, you'll see a light blue screen with the heading CHEEIMG.nhb followed by a few other entries below it. The instructions at the bottom of the screen says to press the power button to continue. Go ahead & press the End Call/Power button to start the ROM flashing.
9. The ROM flashing takes about 15 mins. When it is completed, the bottom of the screen will say Update successful and the entries above with the OK appended at the end.
10. Reset the Treo 750 with the stylus & immediately perform a Hard Reset. This is accomplished by pressing and holding the End Call/Power button and simultaneously resetting the Treo 750. When prompted to Erase all data, release all the previously held keys and press the Up key of the D-Pad.
11. Once the formatting of the RAM has completed, the Treo 750 will continue to bootup & you will go through the standard startup wizard for setting up your Treo 750 for the first time.
Everything else should proceed as per normal.
I'm writing this from memory because I've just unbranded my AT&T Treo 750 & am now on WM6.1 Professional.
Please perform the abovementioned steps at your own risk. I'm not responsible for any damage that might result from the procedure.
All the best!
thks, i tried this and post later
thks again
hi all, i tried the procedure, and now my treo freeze in the palm logo off and freeze again in the palm logo, pls help....
thks
moontger2 said:
hi all, i tried the procedure, and now my treo freeze in the palm logo off and freeze again in the palm logo, pls help....
thks
Click to expand...
Click to collapse
I tried this method and I had the same problem as you.Try this method.
1. Download the official unbranded bits here:
http://palmone.r3h.net/downloads.pal...topUpdater.zip
2. Extract the EXE file that is in the zip file (give it a specific folder to extract to, the zip file uses a funky folder name).
3. Run the EXE file, but stop when the gui pops up.
4. At the first screen, navigate to c:\Documents and Settings\your username\Local Settings\temp, then inside the temp folder you will see a palm folder, and a folder with some random numbers and letters like PQa02356.
5. Enter the installer temp directory
8. right click payloads.xml file and select edit with notepad
9.Replace the RWE carrier text with ATT if your phone was from ATT, then
Replace the high 1.16 version with 2.27
11.After you have made the necessary changes click on file-save as, then save it back into the same file as it was originally in, and save as (all files)
if you save it as a text file it won't work.It must be saved as payloads.xml
with the xml attributes.
12. Go back to the installer screen and continue with installation
13. You must complete the installation successfully, if it fails, rerun the whole process. If it isn't successful, the flash ROM isn't "closed" and you won't see the new version numbers updated, and what not else as well.
Ta daaaaa and it runs HSDPA !!!
It worked great for me. My treo was fairly new with winmo6 version 2.25 with ATT branding, and nobody seemed to have the exact directions that worked for my phone. feel free to pm me if you need any help.
Now I have the unbranded 2.27 version.It works flawlessly
rabbiporkchop said:
I tried this method and I had the same problem as you.Try this method.
1. Download the official unbranded bits here:
http://palmone.r3h.net/downloads.pal...topUpdater.zip
2. Extract the EXE file that is in the zip file (give it a specific folder to extract to, the zip file uses a funky folder name).
3. Run the EXE file, but stop when the gui pops up.
4. At the first screen, navigate to c:\Documents and Settings\your username\Local Settings\temp, then inside the temp folder you will see a palm folder, and a folder with some random numbers and letters like PQa02356.
5. Enter the installer temp directory
8. right click payloads.xml file and select edit with notepad
9.Replace the RWE carrier text with ATT if your phone was from ATT, then
Replace the high 1.16 version with 2.27
11.After you have made the necessary changes click on file-save as, then save it back into the same file as it was originally in, and save as (all files)
if you save it as a text file it won't work.It must be saved as payloads.xml
with the xml attributes.
12. Go back to the installer screen and continue with installation
13. You must complete the installation successfully, if it fails, rerun the whole process. If it isn't successful, the flash ROM isn't "closed" and you won't see the new version numbers updated, and what not else as well.
Ta daaaaa and it runs HSDPA !!!
It worked great for me. My treo was fairly new with winmo6 version 2.25 with ATT branding, and nobody seemed to have the exact directions that worked for my phone. feel free to pm me if you need any help.
Now I have the unbranded 2.27 version.It works flawlessly
Click to expand...
Click to collapse
Oh My God!
this trick works flawlessy. thank a lot for sharing.
i have a vodafone (VFE 1.16) before now its VFE 2.23
Anyone know where I can download Treo750_2_23_ROW_EN_DesktopUpdater.zip? It seems to no longer be on the palm site.
Thanks,
Steve
...got the same problem. I don't ow where to download any desktop updater. All palm links are dead.
try this link:
http://www.4shared.com/file/74485997/733843ff/Treo750_2_27_ROW_EN_DesktopUpdater.html?err=no-sess
Thanks a lot, YOU RULAZ!
I currently have an unlocked At&T branded 750 with WM 5.2 What will this download do for me? Unbrand my device or just update WM? Please understand that I am a Newbie at this. How do I upload this software to my 750 device?
i need help, i found methods but when i make it , dont work for me,continue the freeze on palm logo
tHx
Oh thx, searched hours and than i found it here.

change operating language phone xperia x1

hey guys
i really need to change my operating language phone in xperia x1
i want it in English not in Dutch
can anyone help me plz
When you need to do a hard spl and when download a wwe rom, there is a thred about it
where can i find that plz would u like give me the link
1. Hard-SPL, please read before you ask more
http://forum.xda-developers.com/showthread.php?t=431218
2. WildChilds ROM: http://forum.xda-developers.com/showthread.php?t=510188
Good Luck!
yopi_smoni said:
where can i find that plz would u like give me the link
Click to expand...
Click to collapse
mattiL said:
1. Hard-SPL, please read before you ask more
http://forum.xda-developers.com/showthread.php?t=431218
2. WildChilds ROM: http://forum.xda-developers.com/showthread.php?t=510188
Good Luck!
Click to expand...
Click to collapse
if u did hard spl once, do not do it again... to change the lenguage just flash any WWE rom you want !
i did that but i nothing happend
1- extract the file you got and rename it to ruu_signed.nbh
2- put the renamed file onto your memory card.
3- remove and insert the battery
4- press the volume down button and while pressing press the power button (keep both button pressed)
5- the mobile should start and give your three colored bars, keep on pressing.
6- a screen will come up showing it is starting to update. now release the two button.
7- wait till all update/intallation has finished.
8- remove and insert battery.
9- power on your mobile and do the initializations and wait for it to install some other programs and files.
10- phone will restart now for the final time.
here is what i Got
i get a 3 colour and
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
serial
then NO IMAGE and back to the above screen.
and i did that too
0a) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
0b) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
1) download Hard-SPL package from attachment, extract to an empty folder.
2) it is recommended you download only the X1_HardSPL_v1.zip unless you want to tinker with MFG SPL (MFG SPL 0.52 is a separate attachment).
3) you must Have Phone Synced with PC in Windows Mobile!
4) run X1_HardSPL.exe. (if you want to flash MFG SPL: at this point replace the extracted RUU_Signed.nbh with the MFG version of RUU_Signed.nbh)
5) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
but i got eurrer 202 what sgould i do now plz
Two problems here (at least)
1. You did not Hard-SPL (the three coloured screen should say something like OliNex 0.72. )
2. To load ROM from memory card, call the file KOVSimg.nbh, not ruu_signed.nbh, that's for loading from windows ROM update utility)

Categories

Resources