radio upgrade now no phone - 8125, K-JAM, P4300, MDA Vario Software Upgrading

tried upgrading just the radio to 2.25. rebooted. now get no radio information on device information. tried hard resetting and rebooting PC. still no radio/phone. can't get the device to be recognized again so i can reload a different os. working with qtek test OS. always had problem with poor phone reception/quality so i tried this upgrade. i've upgraded numerous times w/o a problem. any suggestions.

no radio/phone anymore
also, battery meter reads as unknown.
3 hard resets later: no luck!
Device information: rom version 2.8.7.1 WWE, rom date 12/5/05, ext rom 2.8.7.101
no radio information!!!!!!!!!!!! help

Try this:
With the phone off, press the camera button and hold it in
Now press the power button for 5-10 seconds
Let go the power button
If the screen comes up with 3 color bars, connect the phone to your computer and run your favorite firmware.
Let us know the results...
Good luck!

thanks yellow dragon
unluckily, i drained the battery last night trying to figure this out. usb port seems broken (dropped?) so i can't recharge it. i wish i had this info earlier. will be smarter next time. appreciate the advice. sending to imate under warranty? crossing my fingers. marc

Re: thanks yellow dragon
Hello Marc,
These devices don't seem to like to have their batteries drained flat.
Here's one trick I've used with my boss PDA which did the same thing, the battery drained and it would not recharge with the stock charger.
You'll need to take out the Wizard's battery.
1. Take a DC adapter that puts out 5-6 VDC.
2. Make a note where the positive and negative terminals are. Usually the center/tip is positive and the barrel/ring is negative but this is not a defacto standard. Check the adapter casing to be sure. DO NOT USE AC OR MORE THAN 6 VOLTS! THE BATTERY PACK COULD BE DAMAGED!
3. Attach a wire to the adapter's positive and another wire to the negative. How you hook it up is left to your imagination
4. Now, with the negative wire coming from the adapter touch the negative terminal on the battery. Touch the positive battery terminal with the positive wire. The battery polarity is printed on the label.
5. Charge the battery like this for 15-30 seconds but no more.
6. Now plug the battery back into the phone and attach the charger.
The battery should start charging now. If it doesn't, it means it is deeply discharged and you'll have to repeat the procedure, this time for 30 seconds tops. Again, remember by doing this procedure you're bypassing the charging/conditioning circuits and the battery could be damaged!
Good luck!

Related

HELP!! PHONE WON'T TURN ON

So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
dew1989 said:
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
Click to expand...
Click to collapse
It seems that you bricked you phone mate. I think that you installed MrClean rom in a G4 phone so you irrimediably f*cked up the bootloader (IPL and SPL). Many users have reported that their phones were able to boot (and behaved normally) immediatly after the flashing but were dead after they turned them off for the first time, this is what happened to you.
Only thing you can try is going to bootloader mode (but i think it won't work since you messed the bootloader) and then flash a new rom. To do this, press and keep pressed both the keys on the right side and then insert a pin in the reset hole briefly. If the phone goes to the tri-colors screen then you're safe, if not continue reading.
If your warranty perior is not yet over then you can have a new phone for free (DON'T tell them that you flashed an experimental rom!!! Tell only that it went off suddenly or that you were installing an official rom!).
Service centre can repair your device (i suppose they've some method to reflash the bootloader) but i don't know how much they'll ask you.
Try asking other users on this forum. Sorry!
bye
...did you ry to recharge it with the ----ORIGINAL 1A CHARGER----? looks stupid, but i resuscitated mine just before throwing it in the bin. if it works, i will explain you the rest....
yup, I tried charging it with the home charger and still nothing. My battery reads at 3v and it's supposed to be 3.8 so it's not out of juice, but maybe it's just dead?
...you can try with just a normal 9 VDC battery, in order to boost up the voltage, to connect it for a few seconds to the ppc battery till you reach the 3.8 VDC and see if it's working...
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
dew1989 said:
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
Click to expand...
Click to collapse
This is waht you need:
http://www.thetravelinsider.info/phones/cellphonerecharger.htm
This charger is somehow wired weird... it charges the battery AND feeds juice to the phone at the same time (believe it or not, regular chargers and USB cables do not engage until the OS is loaded), allowing you to turn the phone on and in a few minutes plug it into the regular charger to continue charging. Just make sure you get the RAZR tip.
It has saved my ass more than once.
I fixed it , What I did was zap the battery with a 9v battery in 3 sec intervals, I did this about 5 times, then I pluged my phone into the charger and turned it on, the 9v gave it enough juice to boot up and the usb took over from there. So to everyone out there who is having this same problem, try this but don't over zap, check your battery with a multimeter.
im having the same problem----my MDA went dead last night because i forgot to charge the battery and then i went to plug it in the charger but the phone doesnt turn on no more...the light doesnt turn on like if it would be charging and i left it overnight and it still doesnt work..... do yall think that its the battery or is the phone just messed up and cant use it nomore????
Last time I had my battery completely drained, it wouldn't charge from laptop via USB. I read something about how the device's "smart-charging" function itself needs a bit of power to start-up...
but anyways, I couldn't charge the battery through the phone (software charging) - what I had to do was to take a USB cable, cut out one end, identify the +/- (red/black) wires, and charge them directly to the battery's two poles (metal plates). It took about 10-20 seconds of charging until I had enough power in the battery to place it back in the phone, start WM5 and charge it thru the phone.
It would have been much easier if you have a battery charger.
I had my phone connected to the computer through the usb cable, and I just left it connected for a week and it was completely dead and could not be turned on. I don't know how it drained the battery (probally by leaving the wifi on, but the computer was in use all the time). Anyway, thanks to this thread, I used the ac charger and it turned on.
Keywords: t-mobile tmobile mda phone won't don't turn on
phone down
thanks for infos
I'm going to give this a go; a Crossbow ROM flash went horribly wrong last night and in my attempts to repair it (I also must have flashed at least 9 times) the phone went dead. It won't charge either, but battery voltage is 3.7 volts, and I'm sat here wishing it was 3
Will get back to you all!
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Suggestion
CrArc said:
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Click to expand...
Click to collapse
My phone has a hardware problem with the on / off button (doesn´t work at all), at the beggining I thought it was a software problem and I tried all sort of tricks, then I gave up and recognized that was a hardware issue and I found 2 ways to turn the phone on 1) When is totally off (This happens when I have to remove the battery to change SIM card) I connect to the USB cable to my PC or to the car or wall charger and I make a soft reset. 2) When I see the phone signal led blinking I remove the memory card and wakes the phone up (not a good idea since I know that the card is going to get damaged sooner or later).
I just got a G3 wizard from a friend a couple days ago. On Thursday I upgraded it to XDA Mobile 6 and left it on the 2.25.11 (I think) T-Mobile Radio that the T-Mobile 2.26 firmware flash put on it. I used it all day on Friday and then I held the power button and shut the phone completely off for 25 hours, but left it plugged in to a usb to 110V AC adapter that came with my Dell Axim X50V. On Saturday night I went to turn it on and it would not come on no matter what I tried. I found this thread and checked the voltage on the battery directly with a multimeter, 3.13V. I cut the head off a usb cable and then held the black and red wires to the positive and negative terminals on the battery for 2 minutes with the head plugged into a front USB port on my PC. The multimeter then read 3.7V. I put it back into the MDA and it turned on, booted and informed me that the battery was completely drained. I plugged it into the USB to AC charger and it read 10% battery on BatteryStatus. I have left it to charge and it is currently at 60%.
I guess the lesson here is to not totally shut the phone off and let it sit, or the battery won't charge, even plugged into my charger. I guess the OS needs to be running in suspend mode for the charging circuit to run. I know I won't turn it all the way off ever again unless I have my little plug thing and my laptop with me.
(old) Nokia phones have a state called "Acting dead" (from service manuals) which takes place when phone is turned off and battery inserted. It means that the energy is flowing around the board so that the responsible hardware keeps waiting for a 'HIGH' signal ordering to turn ON the phone.
When batteries go bellow the 2.x volts they stop being charged by the phones. This is why i protect the battery terminals with tape when the phone is stored for some time and the reason why a lot of people thinks the phones are broken when not used for months. I usually use the 'freezer trick' where i leave the batteries inside the freezer all night and charge them next day.
just 2 cents...
My Wizard XDA got discharged over the weekend and wouldn't start up - after 12 hours on USB it still wouldn't start.
The charge tips saved my bacon - I modified a USB cable as per the instructions above, and used it to charge up the XDA battery - it only needed five seconds and the phone now boots!
Thanks All, great information!
My 2 cents...
If you're going to try the same, connect red usb to the +ve terminal of your battery and black USB to the -ve terminal of the battery. I'd suggest having a voltmeter to hand to check battery and supply voltage.
Disclaimer - the ablve worked for me, but I'm not responsible for anyone damaging themselves, their PC,their phone or anything else by using the above info!
BUMP! thought my phone was dead, hacked a USB cable and i'm back in business!!!!
TYTN II won't turn on
i left it plugged in all day and when i tried to turn it on it didn't respond. i have a second battery that was fully charged and that didn't work either. i tried a hard reset with it unplugged and with it plugged into the charger. nothing works. i'm on the standard at&t rom with lots of programs. i got it unlocked so i can't go to at&t.

Lost all signs, phone doesn't turn on anymore(even on wall charger). Is it bricked??

Folks,
I was flashing CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE and the battery went down. The flashing procedure stopped at 85%.
After this incident I could not turn on the phone again. It spent all night recharging and nothing.
What should I do?
------------
Tmobile MDA VARIO
IPL 1.05
SPL 3.08
Wizard Love Rom
Did you charge it over night with the wall charger or with the sync cable? If Windows doesn't recognize the phone, as it might not since you were in the middle of flashing, it may not provide a charge through the sync cable. You might have just thought you were charging it but you weren't.
I was charging with the wall charger, and nothing happens at all (no lights, no bootloader)
Did I brick the phone?
Is there a way to brick the phone while flashing this rom and losing battery power or it's not bricked?
Try pulling your battery for 10 min or so and then put it back in. Phones don't usually get bricked by getting interupted in the middle of a flash. If they did, there would be a lot more people around here with bricked phones because I've see a whole lot of threads in here with people saying they got interupted in the middle of a flash. I don't think you should start worrying about that quite yet.
So I'm taking off the battery for a while, let's see what happens...
I can't see any signal even if the battery is out, and the wall charger is plugged anyway.
I've pull off the battery for about 20 minutes (battery was in refrigerator at this time) and nothing happened.
Is there anything else to do?
(ps:I'm not using the original wall charger...)
I've pull off the battery for about 20 minutes (battery was in refrigerator at this time) and nothing happened.
Is there anything else to do?
(ps:I'm not using the original wall charger...)
Edit:
Now I'm trying to do this below:
SteRo SteRo is offline
Junior Member
Join Date: Nov 2005
Posts: 15
Default
OK here's the solution.
First of all, be aware that the MDA can NOT charge unless the OS is fully loaded. If for whatever reason your battery gets fully depleted, you have to do the following (it involves ruining a 5 $ cable and doing some surgery):
- first, go out and buy a new USB-to-mini-USB cable, unless you have 2 already (or one and the original charger)
- take out the battery
- take the USB-to-mini-USB cable, cut off the mini-USB plug and expose the four wires
- strip the red (+) and black (-) wire and twist the copper ends of each wire
- now CAREFULLY attach the right wire to the right connector on the battery (so + on + and - on -) and tape it there so it stays firmly on
- put the cable in your (running) PC or put the charger in the wall socket
- let the battery recharge for an hour or so, then put it back in the Wizard and reboot
- now when it is fully rebooted, you need the second cable to charge your Wizard completely, the way you're used to.
Worked for me! I've kept the ruined cable, just in case it happens again.
Good luck!
Click to expand...
Click to collapse
Hope that works/worked for you, let me know if it does.
I made the cable, tried to recharge battery for 1 hour nd nothing again...no lights, no signs...still with a dead phone...
Does anyone have a suggestion?
Do you have access to a volt meter? If you do, check and see if you get any voltage on the battery at all. Maybe your battery is shot. Theres no reason for your phone to be bricked so I wouldn't give up just yet.
Theres also another trick that someone else having a similar problem in another post reminded me of to jump start your battery. It involves a 9v battery and a couple of wires (bread ties will work if you don't have any wires laying around). It's pretty much the same thing as the charger thing to an extent. You take the 9v battery and attach the wires(bread ties) from the - to the minus on your cell battery and + to + but only do that for 10 seconds and then remove them, wait 30 seconds and then do it again for 10 seconds. Repeat that 10 times and then put the battery back in to the phone and connect the charger. If that doesn't jump start it your battery might be gone for good.
Thanx, I'll try it too.
Maybe tomorrow I'll have access to a second battery with a friend of mine.(fully charged and working battery)
Do you know why is the phone not showing any lights? Is there any explanation (for the case it's not bricked)?
If the battery is completely drained it won't take a charge (this is actually a well known issue with wizards) the charge lights won't come on because they are actually taking their current straight from the battery.
if you not using charger that came with phone thats probably your issue charger that came with phone is 1amp most secondary chargers are 500ma
I think the phone is really dead now.
I´ve put my friend´s battery in my phone and nothing happened. (no signs)
My battery worked with my friend's phone too...
What are the solutions now? A new motherboard?
vdalesandro said:
I think the phone is really dead now.
I´ve put my friend´s battery in my phone and nothing happened. (no signs)
My battery worked with my friend's phone too...
What are the solutions now? A new motherboard?
Click to expand...
Click to collapse
I've just reread your initial post and i think you're both guilty and unlucky. Guilty for acknowledging the RUU warning about using a charged battery (check boxes) and unlucky because the flashing might have stopped while writing to the IPL zone.
So i do think that new board is the only solution here. Sorry.
Where are cheap boards for sale?

Problem with startup 6515 - need advice

Chaps
Yesterday my 6515 stopped cooperate with me! Totally!
- I didn't dropped him or physically damaged,
- The battery was charged in 85% just before it was switched off itself
- Back cover closed with no gaps between cover and body
- Was fully functional when suddenly switched off
- I didn't upgraded anythihng before.
Symptoms:
- Ipaq is not reacting on start button
- Not reacting on reset
- Not reacting on hard reset
- The left diode blinking red during charging via usb cradle when I’m pressing power up button
- The same happens with regular charger
- During charging with regular charger when I’m opening the back panel the diode stop blink and become flash continuously in red.
I have already tried almost everything to start it up:
Changed the battery,
Open, close the back battery panel
With and without SD card
Appreciate any HELP!
small update
Ok I have made some progress..
Now I can see the bootloader screen and that's it.
What to do next ???
Im not sure what blinking red means but when you remove the backcover, the red led will lite up.
Try to do a hard reset, and see if it restarts without going to bootloader. Otherwise, you will probably need to upgrade the firmware from the bootloader screen. Download the latest rom updates from hp.
cluurk said:
Im not sure what blinking red means but when you remove the backcover, the red led will lite up.
Try to do a hard reset, and see if it restarts without going to bootloader. Otherwise, you will probably need to upgrade the firmware from the bootloader screen. Download the latest rom updates from hp.
Click to expand...
Click to collapse
Thanks for reply
Indeed! When I opened back cover the led become flash continuously!
I have tried to apply the rom update from HP unfortunately all of the updates have to be done through Active sync!
It is impossible in current situation because of pressing Power+Joystick+Reset the ootloader screen appear but then nothing This is happens only when PDA is charging with regular charger. Using USB charge or battery power I can't even start the bootloader screen.
From where can I download the SD bootable image or how to make it?
And again small step ahead:
Hi
And again small step ahead:
In craddle there is another input for power so I managed to power it up and connect.
I had to switch of firewall (otherwise i have error 601 - unable to connect the device or something simmillar) and reinstall Active sync back to 3.8
Got bootloader screen USB and hp logo and v 021
by running romupdate utility downloaded from hp site ( whatever the version is ) I finally recognized my model version: it is 6515c
Next
Found valid version from HP site for 6515c ( i think 1.21) and successfully upgraded. No breaks, no other issues just successfully uploadede into finish.
Then hard reset and......
The system starts, screen flashes up, system start loading and the screen fading out. ... and again ..... and again ...... and again and the nothing!
I have tried again to pull out back cover, remove batery, put it back after some time, place back the cover and again.
Nothin' Nada Null %$#@%!$#ing piece of junk.
BTW it is happening only where PDA it is connected to AC power. On battery system is not booting, no booloader nothing!
Any suggestions? Pleeeeeeeease!
After you upgraded the firmware and it started up, was this done with the pda on AC or battery power? If its on battery and it starts fading, your battery is probably screwed. Did you also know there are 2 batteries in the IPaq?
Oh and if its a battery problem, you will need to leave the battery+pda connected to the AC for a while before it can startup and probably into booloader. Run your firmware upgrade again and power it on with the AC connected! If it boots up fine, then monitor the battery status bars in the Power settings and see if both the LiIon and NiMh batteries are holding charge. Hopefully from here you can find a dead battery.
Another thing you could try is to reset the battery when in bootloader mode once you are certain its the battery
http://blogs.unbolt.net/index.php/brinley/2006/08/02/howto_reset_discharged_battery_for_ipaq_6515
Battery reset? Could might be the issue?
Hi
I really appreciate your response.
The whole upgrade and the other stuff have been done with inserted battery and AC connected.
I plugged the PDA into the cradle which was connected to PC via USB and I plugged also AC into the cradle AC input.
It is fading just after reboot only when the iPAQ is connected to AC power (of course battery is inserted otherwise it will not startup anyway.)
On pure battery power it doesn’t giving any signs of living whatever button has been pressed.
The link you provided might contain very valuable directions to me. The man is learning within whole life and dying still being stupid.
I thought that I read the info from the site you suggested but I probably missed the meaning of the post regarding battery reset. That might be this. I will check and update you very soon.
I did the steps from above link. The iPAQ rebooted, started to load the os and again faded out….
Question to everybody:
During bootloader screen appear should I have any diode flashing blinking or whatever
I’m asking because of mine is blind!
Nothing is flashing, blinking, beaming or shining. Just two, completely dead diodes.
Hi, I've just found out what flashing red means
"green blinking means GSM coverage, yellow blinking - missed reminder or alarm clock signal, permanent yellow - recharging, green - the battery is full, red blinking means greatly discharged battery, pale blue blinking - Bluetooth is on"
I think one of your batteries is dead, and if you have already replaced to LiIon battery then you'll probably have to try to replace the NiMh one inside. I cant think of anything else to try
Battery????
Damn!
I think I have a hardware problem! I have 2 batteries: one brand new and the old one. Both not working! Moreover they're not charging! They suppose to charge when I put PDA into the craddle or directly plug to AC charger but they aren't.
No diode is flashing during charging. Damn.
I will try to borrow one battery from one of my friend just to check if this is it!
I will let you know later on.
If I recall correctly, the charging led does not light up in bootloader mode. I maybe wrong though. I think you should try to check the voltage in the LiIon battery to determine if they are being charged.
Also you never mentioned checking the backup NiMh battery. I believe that the NiMh battery is required to power up of the ipaq as well so it may be the cause of your ipaq dying after starting up.
NiMh backup battery
Fortunately I know someone who can charge the battery for me. There will be no problem with that.
From the other side I'm worry about the phone charging....
Why I can't charge the battery using iPAQ?
Next you mentioned about "NiMh battery". I'm sorry for my ignorance but what is that?
Is it secondary battery ?????
Is there any way to charge or replace it? Is it pluggable battery? Where is located?
Yes there is a secondary battery. However, I do not know where it is either.
Here is an example from a different PDA
http://paulstravelpictures.com/HP-iPAQ-HX4700-PDA-Backup-Battery-Replacement-Guide/index.html
If you want to open up your IPAQ do it at your OWN RISK!
cluurk said:
Yes there is a secondary battery. However, I do not know where it is either.
Here is an example from a different PDA
http://paulstravelpictures.com/HP-iPAQ-HX4700-PDA-Backup-Battery-Replacement-Guide/index.html
If you want to open up your IPAQ do it at your OWN RISK!
Click to expand...
Click to collapse
You don't need to touch that one, this battery is designed for save your data when you exchange the main battery.
commanddos said:
Damn!
I think I have a hardware problem! I have 2 batteries: one brand new and the old one. Both not working! Moreover they're not charging! They suppose to charge when I put PDA into the craddle or directly plug to AC charger but they aren't.
No diode is flashing during charging. Damn.
I will try to borrow one battery from one of my friend just to check if this is it!
I will let you know later on.
Click to expand...
Click to collapse
Commadnnos,
Sound like your 6515 has battery charging problem. If the charging failed, even you have brand new battery, it won't be charged at all.
Since you have two batteries, you might want to buy a external battery charger to prove those two batteries are good.
I think the charge circuit is in the second PCB board which under the keyboard inside your 6515; if those batteries are good, you might want to buy a dead 6515 and replace it by yourself...
Cheers,
watchsat said:
Commadnnos,
Sound like your 6515 has battery charging problem. If the charging failed, even you have brand new battery, it won't be charged at all.
Since you have two batteries, you might want to buy a external battery charger to prove those two batteries are good.
I think the charge circuit is in the second PCB board which under the keyboard inside your 6515; if those batteries are good, you might want to buy a dead 6515 and replace it by yourself...
Cheers,
Click to expand...
Click to collapse
Well Well Well ..... it is getting wormer. Many thanks to everyone who are still trying to help me out. Thanks again.
Is that mean the secondary battery is located under the keyboard? I saw the photos from unassembled 6515 and it looks like the secondary battery. To replace it you have to first remove 3 screws, unplug the LCD and remove whole main board.
Is that means that the charging circuit has been built in the keyboard plate?
Thank You all. Patient died......
I would like to thank everyone for help. I think we can close this thread over here.
My beetle just went out into the "digital heaven".
The HP support specialist ensured me (without any tips or hints from my side) that mainly there is a problem with passing the power from the charger to the battery which means no more no less like ".... dude your motherboard is screwed. You have to get the new one or whatever...!"
So now it is a time for selling the rest of the parts on auctions......
R.I.P (Rust In Peace)
if the red light blinks
1 your battery has problem
or
2 your battery cover has problem. The plastic part on the back of your battery cover may have broken which touchs the microswith on the mainboard.
if that microswitch is not triggered , the hw65xx,hw69xx will not turn on.

Wizard wont start after Low battery

After I googled around i found that Wizard have a problem. So when the battery gets low and the phone got shutdown because that reason, i must use a new battery (or do some hijacking with the cables) to power up the old battery again.
Seems that the usb connector cant charge the current battery if its Windows is not started. This is very weird and stupid, so i dont belive it, can some one confirm ?
Btw, my phone startups until the "Windows" screen when loading and nothing more.
It is indeed true, if your charger is not strong enough. You MUST use a WALL CHARGER, not a USB connection on your computer with an output of 1AMP in order to charge a completely dead Wizard battery.
the interesting part is that... i met one of my friends and he take a look of the battery (i dont know much about electricity things). So the battery was 80% charged...a hard reset finished the job, but took me 1 day for searching for new battery and searching for fix. Seems that the problem was from windows mobile, but i will go and buy a wall charger for any future case
10x for the fast reply
yes, impossible to charge while the battery is completely dry ...
When the battery goes dry the only way (known by me) to recharge it is that I pull out the battery and make contact on the battery using needles to make contact from 5 Volt charger to battery (don't do it if your not sure which one is + ) for about 1 minute and thats enough to wake up the ppc.
this is not the best way, for sure ,,, but it works.
Try the PC reset trick. Take the battery out and unplug the USB. Hold down the reset pin for 20 to 30 seconds. Put the battery back in and try to power it up.
I don't know if it will work. On a PC the circuitry gets some sort of internal power loop going on in the capacitors. Removing all the power and holding the power button on for 20 to 30 seconds will short out the condition. Then everything works fine.

Another brick in the Wall... :-( Needing help with Wizard

Shortly: I flashed a new rom (not so new... Mameli 2.0 with WM6.1) and the upgrade process stuck on 99%, computer saying "All Done"
No so... trying to reboot the Wizard gets up the bootloader screen... no problem, will you say BUT... I was in a hurry so I leave the USB cable connected and go away for a few hours (I suppose the USB cable may keep powered the device but now I guess no... )
So, when I came back, the Wizard was turned off.
First try was soft resetting the device with no success: screen remains black.
Then I try to connect the power supply and nothing happened...
Then I pull off the battery and keep it off for a few seconds... I was googling with the device in this state when the bootloader screen pops up for not more then 15 seconds then blank again...
No way to enter bootloader mode or to hard reset the device...
I suppose the battery goes almost flat... and I've not a cradle... is there any way to charge the battery? or a way to build up a cradle-substitute?
May be the issue due to battery flat?
Thanks, Pino
Try plugging in to the original charger, not a USB cable, with the power off.
After about a minute you should see the orange LED turn on.
At least that has worked for me when my battery has been dead.
Nothing... It was already done... I suppose the charging doesn't happen if the OS didn't load... even if I read about some stating that if the charger supplies 1.0A the charge happens...
Now I'm trying to charge the battery with "alternatives" methods...
Thank you for your interest
and so?!?!?
So much lurking... noone writing?
Ideas welcome....
I've done something similar to this too, i.e., where battery gets so low that phone cannot start charging cycle.
Here is what I have done. Take note on the battery of the positive and negative terminals (clearly marked on battery). Use a regular 9V battery and some wire (or 9V connector) and connect the 9V to the phone battery (+ to + and - to -). Allow the phone battery to recharge some from the 9V. I suggest connecting for about 1 minute or so and then disconnecting again for 1 minute or so, and repeat this cycle a dozen times or (or more) using this 50% duty cycle charging. (not sure about charging current, nor heating of battery and don't want to overheat or damage the phone battery).
After giving the phone battery some (re)charging, then try plugging phone in to see if charging cycle comes on. (try first without trying to turn on the phone. If no response then try turning phone on while plugged in to USB). Generally makes no difference whether using USB plugged into computer, original charger or after market, ... phone does not, nor cannot discriminate between different 5V 'USB' sources.
If this doesn't work then the next step is to carefully touch the 9 V to the battery while in the phone and connected to USB (and to play this safe use charger, and not computer USB ... don't want to risk damage to computer). I would only try this if you feel extremely comfortable with electronics and voltages (albeit this is very low voltage) and as a last resort. KEEP IN MIND YOU WILL BE DOING THIS AT YOUR OWN RISK, and I don't want to be blamed for anything that may go wrong with the phone or otherwise by you trying this. This has worked for me on several occassions, but I am an engineer who has experimented with electronic ciruits off and on for 16 + years and so feel comfortable doing stuff like this. (again remember + to + and - to -, battery to battery).
Good Luck
First of all... Thanks for replying...
The problem isn't due to battery too much empty (it's a frequent issue, with mobile phones too...)
I suppose the Wizard needs be correctly initialized to start charging the battery and mine was in bootloader mode.
Sometimes I am able to power up the system for a little while and the bootloader screen appears but the battery doesn't charges so I cannot disconnect the power supply... this is why I suppose I'd get better times if I got a cradle.
Now I'm trying to arrange a flying connection between the battery and my kaiser's desktop charger to give the battery a bit of charge and verify my ipotesys (uh-oh... it's correctly spelled? sorry for my bad english....)
OK, wish me luck
stay tuned...
OK, no more bricked
The issue, as I supposed, was due to a flat battery!!!
I tried unsuccessfully to charge it back using the external charger for my Kaiser, probably the unsuccess was due to difficult to obtain a stable contact between charger pins and battery leads...
After that I remembered I had another battery. It wasn't used for a bit of months (I use the wizard just as backup, when the Kaiser is out of order) but luckily I stored it full charged so the battery was able to make my wizard power up (strange thing, I needed to keep the power button pressed as the device powers down as soon as I release the button!!!)
I tried to update the rom again but it failed at 99% so now I reverted to an old rom but the device is still alive...
Maybe I'll try again the update but not before having fully charged both batteries
See You and thanks to everyone tried to help...
Pino

Categories

Resources