WAp for O2 XDA2s - MDA III, XDA III, PDA2k, 9090 Software Upgrading

does anyone know how to configure WAP for XDA2s PDA?

Do you mean WAP? Or GPRS? Either way, you'll find a file here which should help you out...

Do those cabs work on WM5 devices as well as WM 2003?

They have done for me (in both WM2K3SE and WM5), the only additional info needed is the DNS Server addresses...
193.113.200.200
193.113.200.201
and the Proxy Server Address
193.113.200.195
...other than that it all works fine!

Related

Need T-Mobile USA GPRS Settings to connect to the Internet

Does any of you know the GRPS configuration for the T-mobile MDA USA?
I lost them and i cannot connect to the internet
Please Help
Thanks
Settings I use . . .
T-Mobile settings
Internet:
Setup a GRPS modem using:
internet3.voicestream.com
or
wap.voicestream.com
I'm using internet 3 because I pay for the VPN service.
My Work Network
T-Mobile WAP
wap.voicestream.com
Proxy settings
Check this network connects to the Internet
Check this network uses proxy server
nothign in proxy server line
click on advanced
WAP 216.155.165.50:8080
MMS Configuration in Mail application
T-Mobile MMS
Gateway: 216.155.165.50
Port: 8080
Server address: http://216.155.174.84/servlets/mms
Connects to My Work Network
jt_armstrong posted the cabs for me in the Wizard forum. Is a little easier than doing it manually..
http://forum.xda-developers.com/viewtopic.php?t=55166
Steven
chow
if you have the t-mobile web plan, your APN is wap.voicestream.com
if you have total internet plan, your APN is internet2.voicestream.com
the t-mobile web is a lot cheaper, you can add the following proxy setting that allow you to get to most of the web, email, and sync with your company exchange.
Proxy setting: getmorespeed.voicestream.com port 8080.
no proxy if you pay for the total internet.
thank you. Worked for me as well.
Re: Settings I use . . .
Hi,
So did you get VPN to work on the phone? If yes, how?
telcontar said:
T-Mobile settings
Internet:
Setup a GRPS modem using:
internet3.voicestream.com
or
wap.voicestream.com
I'm using internet 3 because I pay for the VPN service.
My Work Network
T-Mobile WAP
wap.voicestream.com
Proxy settings
Check this network connects to the Internet
Check this network uses proxy server
nothign in proxy server line
click on advanced
WAP 216.155.165.50:8080
MMS Configuration in Mail application
T-Mobile MMS
Gateway: 216.155.165.50
Port: 8080
Server address: http://216.155.174.84/servlets/mms
Connects to My Work Network
Click to expand...
Click to collapse

Can't get T-MobileWeb to work on Unlocked Tilt on T-Mobile

Did anyone successfully get T-MobileWeb to work on the Tilt to get internet access? I am able to send/receive email but cannot get PIE to connect tot he internet. I've setup the usual T-Mo proxy setting but is there another proxy in PIE somewhere? Is it an issue with PIE connecting through a WAP port?
Thanks.
__________________
I think therefore I am.... confused!!!
you need to search forums for tilt tmobile, thats what i had to do..how are your MMS working out... i cant get mine to work after i changed my proxy to get the $5.99 hack... i am thinking i might have to get the data plan.. let me know if you get it working...
these are the settings i am using;
Under Modem,Edit, needs to be wap.voicestream.com
under Proxy the setting needs to be, see below;
This network connects to internet, network uses a proxy server to connect, box need to be checked.. 216.155.165.50, then under advance
216.155.165.50 port:8080
216.155.165.50 port:1901
216.155.165.50 port:1901 or 03 worked for me
sockets, need to be blank
guys, i was able to get both working, however, not on the stock at&t tilt rom. first to get the mms working, i just went to settings-connections-connection setup, and let it setup ur settings for tmobile usa. this will not allow your mms to work. now go to the connections and modify the settings for the 5.99 plan (i posted the exact settings a while back, search for it).. all u pretty much gotta do is add the proxy. good luck
omar
ps..if ur using the tilt rom, i never got the mms working, and wasnt able to access the internet on the 5.99 plan. on the 19.99 plan worked fine tho
omaralt said:
guys, i was able to get both working, however, not on the stock at&t tilt rom. first to get the mms working, i just went to settings-connections-connection setup, and let it setup ur settings for tmobile usa. this will not allow your mms to work. now go to the connections and modify the settings for the 5.99 plan (i posted the exact settings a while back, search for it).. all u pretty much gotta do is add the proxy. good luck
omar
ps..if ur using the tilt rom, i never got the mms working, and wasnt able to access the internet on the 5.99 plan. on the 19.99 plan worked fine tho
Click to expand...
Click to collapse
Here's the setting:
5.99
start
settings
connections
connections
under proxy settings check: this network connects to the internet
check this network uses a proxy server to connect to the internet
proxy server should be :216.155.165.50
click advanced
http: 216.155.165.50:8080
wap: 216.155.165.50:9201
secure wap: 216.155.165.50:9201
socks (blank)
under modem, your access point name should be : wap.voicestream.com
name and password blank.
under advanced check use server assigned ip address
use software compression
use ip header compression.
T-Mobile Total Internet
The only differences is instead of wap.voicestream.com, its:
internet2.voicestream.com or internet3.voicestream.com
And instead of ports 9201 its 9203.
i did try those settings...(that is what they are set to now) my internet has no problems, but my MMS does not... so i cant understand the prob!
I've tried all the settings provided by we3zy but still can't get it to work. In PIE, it kept on saying "opening..." and then came back with the following error:
Error 502 - Bad Request
The server could not resolve your request for url: /
Any thoughts?
- Thanks.
OK, got it to work with accessing internet and email by adding a modem setting. However, I have to switch the two connections depending on which function I need.
Under Setting, Connections, Advanced button, Select Networks...I need to do the following:
In the Network Management screen I have a few choices but only the two settings in the top choice (Programs that automatically connect to the internet should connect using: ) need switching. When I click on to select the choices, I have setup one for accessing the internet and another to get email.
Is this normal or am I the only one that have this issue? Its kind of annoying to keep on switching the setting for the functions. Any way to combine the two connections or have the device auto choose and connect automatically?
we3zy said:
Here's the setting:
5.99
start
settings
connections
connections
under proxy settings check: this network connects to the internet
check this network uses a proxy server to connect to the internet
proxy server should be :216.155.165.50
click advanced
http: 216.155.165.50:8080
wap: 216.155.165.50:9201
secure wap: 216.155.165.50:9201
socks (blank)
under modem, your access point name should be : wap.voicestream.com
name and password blank.
under advanced check use server assigned ip address
use software compression
use ip header compression.
T-Mobile Total Internet
The only differences is instead of wap.voicestream.com, its:
internet2.voicestream.com or internet3.voicestream.com
And instead of ports 9201 its 9203.
Click to expand...
Click to collapse
I used the 5.99 setting and this is exactly what my explorer's (PIE, Opera and email also says cant connect using this connection say.
"Error: Requested content 'www.google.com/m' cannot be accessed. You do not have access to the site. "
moddin said:
I used the 5.99 setting and this is exactly what my explorer's (PIE, Opera and email also says cant connect using this connection say.
"Error: Requested content 'www.google.com/m' cannot be accessed. You do not have access to the site. "
Click to expand...
Click to collapse
I really can't explain why your getting that problem. But visit www.yahoo.com and then visit google.com again. I had that problem on the iphone, don't know why.
Make sure you've checked:
use software compression
use ip header compression.
and all ports are 9201
the settings above worked to get ny internet browser up i am currently on google with the original at&t rom now im gonna check my emails and weather plug ins
we3zy said:
I really can't explain why your getting that problem. But visit www.yahoo.com and then visit google.com again. I had that problem on the iphone, don't know why.
Make sure you've checked:
use software compression
use ip header compression.
and all ports are 9201
Click to expand...
Click to collapse
They are all checked. I changed all ports to 9201 even the http and now when i open pie it says
"You do not have access rights to this site
URL=www.google.com/
Status=20(hex)"
Also it adds "wsp://" in front of any link i type in the browser. Maybe you didnt mean change the http port to 9201 but i gave it a shot. are you guys and XXwindowsXX using the 5.99 deal? and it works?
email routing issue + cannot download TM's w/ pics
Hi All ~~
It sounds like I may have found the right msg board! I am a T-Mobile customer using an unlocked AT&T phone with the original ROM (minus the bloatware). I currently have three msging accounts on the Tilt: text msging, a hotmail account and a work email account (which I check via Outlook on my PC). I am having two annoying problems:
(1) I keep getting TMs saying that I have received an email on my work account; however I cannot (a) get the text msg notifications to turn off, nor (b) get the emails to actually pull down into the account. So: I know I have a work email (even who from), but cannot read it. Any thoughts on how to resolve either or both of these issues?
(2) I cannot receive or send pic text msgs. Really annoying; I am curious to see how other T-Mobile Tilt users have their settings arranged for this.
Thank you in advance for any assistance you can provide ~~ Kim
TYTN/Hermes settings?
These settings in post four, would they be the same for the HTC TYTN/Hermes as well? After going into cnections, I notice that there isn't anything called connection settings. Just add new modem conection, proxy settings etc. I'd really like to be able to get this T-Zones up and running on my Hermes as well.
Thanks,
Cristobal
Cristobalm said:
These settings in post four, would they be the same for the HTC TYTN/Hermes as well? After going into cnections, I notice that there isn't anything called connection settings. Just add new modem conection, proxy settings etc. I'd really like to be able to get this T-Zones up and running on my Hermes as well.
Thanks,
Cristobal
Click to expand...
Click to collapse
Yes, it should be. You'll need to add a new modem connection and edit the proxy settings. PM me if you can't get it to work and I'll try to help you.
Tilt Solution To Force Http Instead Of Wsp On Tmobile
Our good friends at ATT have two cab files in the \windows folder which install and remove a hidden proxy. By default, it funnels through the proxy.
​ BAD ATT! ​
If you are using T-mobile's 5.99 gprs plan and the HIDDEN proxy is enabled, all traffic will be routed through the hidden proxy and you will be forced to WSP:// pages. This will effectively lock you out of many of the sites that do not support the WSP protocol. Other carriers (Orange?) may be doing this too to drive WSP traffic.
To correct the problem, go to the windows folder and
1. run the restoreHiddenProxy4CWS_0522.cab
2. and then run the removeHiddenProxy4CWS_0522.cab file
3. Close your data connection and restart it. If you don't know how, just press the reset button.
After this is complete install the standard T-mobile GPRS settings and you should be in good shape. If you need a cab for t-mobile, search the board for the most current one or PM me. I keep one handy too.
liquidsilver said:
Our good friends at ATT have two cab files in the \windows folder which install and remove a hidden proxy. By default, it funnels through the proxy.
​ BAD ATT! ​
If you are using T-mobile's 5.99 gprs plan and the HIDDEN proxy is enabled, all traffic will be routed through the hidden proxy and you will be forced to WSP:// pages. This will effectively lock you out of many of the sites that do not support the WSP protocol. Other carriers (Orange?) may be doing this too to drive WSP traffic.
To correct the problem, go to the windows folder and
1. run the restoreHiddenProxy4CWS_0522.cab
2. and then run the removeHiddenProxy4CWS_0522.cab file
3. Close your data connection and restart it. If you don't know how, just press the reset button.
After this is complete install the standard T-mobile GPRS settings and you should be in good shape. If you need a cab for t-mobile, search the board for the most current one or PM me. I keep one handy too.
Click to expand...
Click to collapse
So after doing that, will I be able to browse regular HTML pages (without going through proxies) using the 5.99 plan ?
i have a ty tn II and t-mobile is my carrier and i have the 19.99 internet plan,so i would like to know what are the correct settings for the MMS cause i cant sent picture messages nor recieve them..please help me thanks
tm1125 said:
i have a ty tn II and t-mobile is my carrier and i have the 19.99 internet plan,so i would like to know what are the correct settings for the MMS cause i cant sent picture messages nor recieve them..please help me thanks
Click to expand...
Click to collapse
try this:
server name: call it whatever you want
Gateway: 216.155.165.50
Port: 8080
Server address: http://216.155.174.84/servlets/mms
Connect via: whatever you called the server name
Sending limit: 300k
WAP version: WAP 2.0
make sure you set this MMS server as default
The 5.99 plan requires a proxy. No exceptions that I'm aware of. The good news is that I've not found a page that I cannot browse. The speed isn't stellar, but quite acceptable. Additionally, since the power requirements for GPRS are low, I check email every 10 minutes.
There are a series of CAB files floating around here somewhere that have all the correct settings for each of the Tmo plans.
Same phone also ulocked for T-mobile Final solution
I suggest that you start afresh (Hard reset your phone)
then go to this link and download the cab
http://forum.xda-developers.com/showpost.php?p=1521768&postcount=70
download this cab
tmobyjoe599.cab
I had the same problem as you but that worked for me and im sure it will work for you.
Oh before i forget make sure that you disable automatic wireless configurator, that stuff is crap.
p.s note to be a pain in the ass. Next time search the forum even google will lead you to the answer of your question.

O2 don't support Diamond

Hi,
I have just purchased a web browsing bolt on for my O2 pay and go account. When I tried to get settings from O2 I was told by them that they have no settings for HTC mobiles - in fact that they didn't support any HTC models. Is this true or are any of you using 02 P&G to access web and email on the Diamond?
Any help would be much appreciated.
Thanks,
Richard
Its true! I cannot receive and send MMS and there is no GPRS conection.
O2 suxx! I'm going to change the operator.
Tesco Mobile do not have any problems with HTC
I am running my Diamond fine with GPRS etc on O2.
Also there are several O2 bundle deals for Diamonds at Expansys (http://www.expansys.com/nc.aspx?i=163250#o2).
When I set up my Diamond it offered an auto-configure settings after first booting which included O2 even though I bought this as standalone sim and contract free from play.com.
ACtually - not sure it will work with Pay & Go - didn't see that bit.
O2 connection settings are here BTW:
http://www.filesaveas.com/gprs.html
I am with o2 on simplicity, I also have the internet bolt on, didnt have to confirgure anything, it downloaded my settings (auto config) and havent had to do a thing. Upgraded firmware to Elite 3 and exactly the same. GPRS EDGE HSDPA all work fine and dandy. I'm in the uk and loving the combination.
Is there any way to run the auto-configure again without a hard reset?
Thanks,
Richard
ziggyred said:
I am running my Diamond fine with GPRS etc on O2.
Also there are several O2 bundle deals for Diamonds at Expansys (http://www.expansys.com/nc.aspx?i=163250#o2).
When I set up my Diamond it offered an auto-configure settings after first booting which included O2 even though I bought this as standalone sim and contract free from play.com.
Click to expand...
Click to collapse
They "don't support" HTC because they sell them under XDA name And o2 in Germany already got XDA Diamond.
Sorry to bump this, just got a Diamond, Im on o2 PAYG (UK)
Tried loads of the settings being banded about online.....
I can access o2's website on the Diamond but nothing else.
Im seriously considering changing provider, but.... I have £75 credit and its been my number for years, I like the extras I get with o2 (texts, rewards etc.)
Has anyone on UK o2 PAYG got it working?
Regards
After weeks of messing I managed to get a friends PDA working on O2 UK PAYG GPRS full internet not just O2 crap its all in the proxy setting i will get them off him and post later.
Tim
There is a way to fool the server into connecting to the web via the WAP APN. Possibly O2 have 'fixed' the workaround, possibly not. It may be worth a try! Be aware that this was published for a previous version of WM, but the settings ought to be similar still:
To setup the XDA on PAYG for internet:
Go to Settings, click on the Connections tab & click on "Connections"
In the first dropdown, "When needed, automatically connect to The Internet using these settings:" select "New..." and give the connection a name (Mine's O2 Wap)
On the "Modem" tab, click on "New..." to create a new modem specification. Give the specification a name (Mine's O2 PAYG GPRS). For the Modem selection, use Cellular Line (GPRS) and set the Baud Rate to 57600 and click on Next.
For the Access point name, use payandgo.o2.co.uk and click Finish
Next, click on the Proxy Settings, and put a check in both the boxes & click Advanced.
Use the following server addresses & ports:
HTTP: 193.113.200.195 port 8080
WAP: 193.113.200.195 port 8080
SOCKS: 193.113.200.195 port 1080 (not sure if this works as I've never had to use it)
OK your way back out to the today screen and launch Internet Explorer
When launching any website for the first time, you'll be asked for a username, password and domain.
Username: payandgo
Password: password
Domain: <empty>
Cheers Tim, that'd be fantastic.
Johnston4111 - Ill give that a shot shortly - menues are pretty similar.
Johnston411 said:
There is a way to fool the server into connecting to the web via the WAP APN. Possibly O2 have 'fixed' the workaround, possibly not. It may be worth a try! Be aware that this was published for a previous version of WM, but the settings ought to be similar still:
To setup the XDA on PAYG for internet:
Go to Settings, click on the Connections tab & click on "Connections"
In the first dropdown, "When needed, automatically connect to The Internet using these settings:" select "New..." and give the connection a name (Mine's O2 Wap)
On the "Modem" tab, click on "New..." to create a new modem specification. Give the specification a name (Mine's O2 PAYG GPRS). For the Modem selection, use Cellular Line (GPRS) and set the Baud Rate to 57600 and click on Next.
For the Access point name, use payandgo.o2.co.uk and click Finish
Next, click on the Proxy Settings, and put a check in both the boxes & click Advanced.
Use the following server addresses & ports:
HTTP: 193.113.200.195 port 8080
WAP: 193.113.200.195 port 8080
SOCKS: 193.113.200.195 port 1080 (not sure if this works as I've never had to use it)
OK your way back out to the today screen and launch Internet Explorer
When launching any website for the first time, you'll be asked for a username, password and domain.
Username: payandgo
Password: password
Domain: <empty>
Click to expand...
Click to collapse
Looks like it worked, you can set the username and password in Proxy settings on the Diamond Menaing no need to enter it at first connection.
This will use my bolt on. correct?
BTW, THANKS!!!!
As far as i know it does.
If not you'll soon notice your credit evaporating.
OggyUK said:
This will use my bolt on. correct?
Click to expand...
Click to collapse
yep it just uses your bolt-on my mates been using these settings for 3 months now with no problems.
Tim
Yeah, bolt on.
Are you lot able to use Remote Desktop? I cant use Live services, Youtube or RD.
This close to taking a contract out with another provider that suport this phone
XDA Ignito is listed as a future handset on O2 UK intranet - all I can say.
So yes, we do support it.
I've got a Diamond and can use picture messages and the internet as well as Live Messenger and Youtube. I don't use RD but I presume it'll work.
I'm on a staff simplicity tariff with the unlimited web bolt on and it all works fine.
Care to share details? do you have different logins?
Youtube loads but videos dont play, I get a synchronisation failed error on Windows Live.
Connection name: mobile web
Modem: Celluar Line (GPRS, 3G)
Access point name: mobile.o2.co.uk
Username: O2web
Password: password
Those work for me, create a new connection in Connection settings. The auto setup tool did it all for me though.
That works for you as you are on a contract.
You won't get wlm etc... on the wap work around on pay as you go. Not sure about remote desktop but i guess it's all related to the proxy.
Remote desktop and messenger both use secure connections so how about trying entering 193.113.200.195 in the WAP Secure section in proxy and try it the following ports numbers 8080,9201,443.
Its only a guess but worth a try I think
Tim

O2 PAYG Web bolt on

I've bought a HTC S730 from expansys.co.uk and a UK O2 PAYG sim with the unlimited web bolt on, Benig a bit of an O2 & S730 novice I just assumed that all I would need to do is simply inset the sim into the handset and I would be free to browse the Internet.
Sadly that didn't work. I've tried all the known APN settings for 02, I've also contacted O2 but as they dont support the handset they couldn't help.
Does anyone here have this handset on O2 PAYG and can access the internet? What settings do I need to enter?
Regards
danb
They wouldnt help a paying customer? Thats really crappy especially since your not asking for "support" on the handset, but the network itself.
Have you used them in the past or do you have a friend with a phone on their network? You should only really need the GPRS configuration stuff to get it connected to their network.
I am not familier with O2 at all but I hope that the following helps, it was what I came up with.
O2 GPRS settings (WAP):
Homepage: http://wap.o2.co.uk/
APN address (PAYG): payandgo.o2.co.uk
Gateway (IP) address : 193.113.200.195
Username : payandgo
Password: password
Session type: Continuous / permanent
Authentication: Normal
Security: Off
Port number: 9201
O2 GPRS settings (Email/Web):
Homepage: http://pda.o2.co.uk/
APN address: mobile.o2.co.uk
Username: mobileweb
Password: password
Session type: Continuous / permanent
Authentication: Normal
Security: Off
Email servers (POP): mail.o2.co.uk
Email servers (SMTP): smtp.o2.co.uk
DNS Servers: 193.113.200.200 and 193.113.200.201
Key that in under Settings > Connections > GPRS > (Either make a new one or edit an existing one (for each I believe)...)
10332007 said:
They wouldnt help a paying customer? Thats really crappy especially since your not asking for "support" on the handset, but the network itself.
Have you used them in the past or do you have a friend with a phone on their network? You should only really need the GPRS configuration stuff to get it connected to their network.
I am not familier with O2 at all but I hope that the following helps, it was what I came up with.
O2 GPRS settings (WAP):
Homepage: http://wap.o2.co.uk/
APN address (PAYG): payandgo.o2.co.uk
Gateway (IP) address : 193.113.200.195
Username : payandgo
Password: password
Session type: Continuous / permanent
Authentication: Normal
Security: Off
Port number: 9201
O2 GPRS settings (Email/Web):
Homepage: http://pda.o2.co.uk/
APN address: mobile.o2.co.uk
Username: mobileweb
Password: password
Session type: Continuous / permanent
Authentication: Normal
Security: Off
Email servers (POP): mail.o2.co.uk
Email servers (SMTP): smtp.o2.co.uk
DNS Servers: 193.113.200.200 and 193.113.200.201
Key that in under Settings > Connections > GPRS > (Either make a new one or edit an existing one (for each I believe)...)
Click to expand...
Click to collapse
Thanks man,
This is the settings for contract sims, either way i've tried it, I found all the APN setting on line, but my problem is that I cant get it to work on this handset.
Does anyone use ON PAYG with HTC's Wings?
Regards
Dan
only other thing I can suggest is are you sure your account has access to the GPRS networks with a data plan or are you trying to see if they will dock minutes / charge you per KB... Hope you get it fixed

T-Mobile Settings? MMS

Anyone have a cab to install all t-mobile settings (mms, web, etc.)? I really just need the MMS to work. I don't care about the web. Thank you!
Server Name
T-mobile MMS
Gateway
216.155.165.50
Port Number
8080
Server Address
http://216.155..174.84/servelets/mms
Connect Via
The WAP Network
Send limit
600K
I have internet connections if you need them
Ricky4723 said:
Server Name
T-mobile MMS
Gateway
216.155.165.50
Port Number
8080
Server Address
http://216.155..174.84/servelets/mms
Connect Via
The WAP Network
Send limit
600K
I have internet connections if you need them
Click to expand...
Click to collapse
whoa, how did you get the 600k limit? i only got the 300k one -__- btw, thanks!
You're welcome, I believe it came standard with the phone. Unless they updated it recently.
yes please... internet settings too
Ricky,
i'd sure like to uptake on your offer for the internet settings too, please.
I've read various opinions on the APN to use...wap.voicestream.com, internet2....., epn...
So far wap... is working for my mms, but how i got it to work is akin to the monkey typing randomly method.
Also do you happen to know if these work for Fuze too?
thanks much much
chris

Categories

Resources