Database Develop

Having to reset Qtek daily cause I don't hear the one I call

Hi
I have the newest firmware version installed on my Qtek 9090 (BA_WWE_14000_147_11200_Ship), and I experience a problem again which I had first when I bought my Qtek but was gone after I had installed Radio version 1.08.00:
Once a day I have to reset my Qtek because I can't hear the one I am calling - usually this happens when I call my mobile phone's answer phone. The phone gets connected but I don't hear anything. After a soft reset everything is fine again.
Is this a known issue? Any solutions to it? Ok - I know I can downgrade to 1.08 again but I dont really wanna do that. And yes, I can stop calling my anser phone ....
Anyone knowing what is causing the problem?
Reagrds,
A

I had the same problem with my Qtek 9090 until I stopped use the Bluetooth feature completely. Since then, everything is fine.

tot 1.12 radio has solved the "no sound" issue.

keeping_sg said:
tot 1.12 radio has solved the "no sound" issue.
Click to expand...
Click to collapse
I cannot verify this, i have an mda3, upped it to R1.12 but i had many "no sound" problems. Now i downgraded to R1.10 and had not a single no sound issue ..yet

ThExSenatoR said:
keeping_sg said:
tot 1.12 radio has solved the "no sound" issue.
Click to expand...
Click to collapse
I cannot verify this, i have an mda3, upped it to R1.12 but i had many "no sound" problems. Now i downgraded to R1.10 and had not a single no sound issue ..yet
Click to expand...
Click to collapse
i have tried 1.06 & 1.10, all are having that issue. that's why i have upgraded to 1.12 so far so good. umm.....................strange..

keeping_sg said:
ThExSenatoR said:
keeping_sg said:
tot 1.12 radio has solved the "no sound" issue.
Click to expand...
Click to collapse
I cannot verify this, i have an mda3, upped it to R1.12 but i had many "no sound" problems. Now i downgraded to R1.10 and had not a single no sound issue ..yet
Click to expand...
Click to collapse
i have tried 1.06 & 1.10, all are having that issue. that's why i have upgraded to 1.12 so far so good. umm.....................strange..
Click to expand...
Click to collapse
For me, radio 1.12 delivered:
- worse signal reception
- higher battery consumption
- still no sound issue.

flashed twice & still having the bloody "no sound" issue. really give up. i think the next thing to change is the motherboard. sigh.........................

I had never had this issues untill I upgraded my Radio to 1.12 and then I had it 5 times in one day, went back to 1.10, no more issues

Hmm. This is a really 'odd' problem. I didn't originally have this problem with my SX66. Then, it just 'popped up' one day, and I can't seem to get rid of it.
I have tried different ROM versions (currently 1.40), and my radio version is at 1.10.
I have NEVER used radio 1.12, so I know that's not the CAUSE.
We need to compile a list of people with the problem, and see exactly what combination of ROM and Radio they have, as well as the programs they have installed.

if you read the cingular forums, there are a few folks there that say they have had it all along so I am not sure where to start...

umm....... different ppl have different problem. seems like it's a integration issue.

If you go to some HK forums, you will also find a lot of people suffering from this.
To me, I seldom use it as a phone. I only use it to receive emails and website browsing. When I go overseas and I used it as a phone with a BT handsfree (shut down GPRS connection), everything is just fine. I only encountered once with no sound problem when I take away my BT handsfree on a plane....
It's definitely a bug since a long time ago with old and new versions.....
Sad....and disappointed......

Hi all,
I upgraded my phone to the 1.12 radio along with the 1.40 CE ROM and am always resetting due to the "can't hear caller" issue and I never had this problem before.
I'm going to do a hard reset and see if that helps (clear out all the apps and use it for a day or so). If this doesn't work, I shall revert back to the 1.10 as I had no problems with that.
ROM 1.40.00
Radio 1.12.00
EXT ROM 1.13.139 (with Updated CallerID [1.20] and older version of O2 Active [3.0])

This cant hear caller issue, is it cant AT ALL hear caler or caller is so faint I cant hear him.
I ask as sometimes I get calls that are faint however when the caller rings back it fine. Not sure if its crap reseption or the device.

I got O2IIs from UK and had the same "No sound" problem. I have to SR about 5 times daily to sort it out. However, if I turn off Bluetooth (pairing with my Bluetrek G2) then everything's OK.
My ROM version is 1.31.00 WWE, Radio : 1.10.00, ExtROM: 1.31.139 WWE and BT 1.0.0 Build 3500
Had up to BT 3900 but wont help. Gonna up radio to 1.12. Will post the outcome soon.

I've only experience the problem once since the imate 1.40 upgrade.
Now, I must say that I don't use the phone THAT heavily.

I upgrade to 1.40 EX, it seems working fine, still the sound quality is not good enough...

people!
A guy called Derek has posted a possible solution to this problem here! http://forum.xda-developers.com/viewtopic.php?p=118364
It involves removing the Bluetooth for the startup because he believes that even with the bluetooth off, the unit is still trying to connect to a bluetooth headset.
I'm going to remove/unpair my Bluetooth Headset and see if that makes a difference. If anyone else can try this and post results I'm sure this would help loads of people.
Dom

Please confirm this and I will post it to wiki

@xdadom,
It's correct. As I mentioned in my post, when I "turned off" Bluetooth, everything's OK. The way I "turned off" Bluetooth is exactly the same with Derek did in his post, i.e. delete "Run_BTTrayCE" from Windows\StartUp\
However, I still need Bluetooth for my hand-free device. In my opinion, it's rather a trick, not a solution to kill "No sound" problem. Anyway, we can wait the updated BT version from supplier to sort it out.

PLEASE HEEELP!!!! NO SOUND on my BA on calls ... :(

I'm having the same problem for a week now...
I was on the street with my BA making calls and all went Ok. I use it for my work, so I do lots of calls a day. Suddenly, I realized, when I call, that the other can not hear me, nor can I hear them! The counter is running, the screen says "Connected". I haven't done anything to change the configuration, nor it have dropped it from my pocket.
I'¡m getting crazy. I don't know what I've done wrong.
Things tried unsuccessfully: Crying or Very sad
-Lots of device resets..... Between tryes and Updates.
- Reinstalled WM5 using a different ROM. Now I have TM 1.3. [http://forum.xda-developers.com/viewtopic.php?t=42632]
- Upgraded Radio to 1.15 (previously, I had 1.13)
- Used a Bluetooth headset. It worked, I could hear the sound from the phone, at least. Only thru the bluetooth headphone. Still, I could not hear any phone-sound from the loudspeaker when I turned off the headphone and the bluetooth headset were disabled, even with the Bluetooth signal ON, as suggested on other post. Each try with a new call. The weird thing is that I CAN hear the loudspeaker when I hear music or the system sounds... :?
- "Installed" the Unidirectional patch (copied the AudioGW.dll file over the old one successfully, reset, etc..)
- Turned off the device and leave it off for a while. Take off the SIM card, touch it (cosmic vibrations Embarassed) Sometimes, before, the SIM card went a little nuts if I resetted the device too much -maybe Confused- or if I got the battery off...
- Last, I've downgraded to the latest WM2003 ROM. Formatted the Storage Space and resseted the Registry Hive. No change. All else is working.
My options are finishing ....
Sorry if this has been posted before, but, at this point, when I've been tried almost (I think) everything, i couldn't find anything relevant using search.
Please, any help will be greatly appreciated!!! Maybe I can use at least a link to another thread..
Thanks

try downgrade your RADIO to 1.13

I've allready upgraded to 1.15 because of this problem. Anyway, I've downgraded just now and nothing same problem..... also: I can not get the handsfree-loudspeaker mode (pressing the "call" button for a while). Just nothing happens
Let's hope mamaich or other cracks read this post
Thanks for ur answer
indra9110 said:
try downgrade your RADIO to 1.13
Click to expand...
Click to collapse
HEEEEEEEEEEEEEEEELPPPPPPPPPPPPPPPP ((

ow... DONT PANIC !!! try flashing once again ... including ROM & RADIO

Rom & Radio flashed again. At no avail
I've used, lastly, the "standard" Rom posted on I-mate website (www.clubimate.com) [ROM: 1.40.00 WWE; Radio: 1.12.00; Protocol: 1337.42], just to checkout and everything (regarding this problem) remains the same.
I've, however, noticed that, before, when I used the volume slider up, first the PDA-volume went up, later the phone-volume. Now it only fully moves up the PDA-volume. I think this have something to do...
Again: Please, help me!!!
Thanks for your answer!!
indra9110 said:
ow... DONT PANIC !!! try flashing once again ... including ROM & RADIO
Click to expand...
Click to collapse

Still the same after 3 flashing sessions
Two days ago, I've sent an e-mail to I-Mate. They have answered me yesterday telling me to hard-reset :?:evil: and if that doesn't work, to send the device to France or Portugal for fixing. Here on Spain there's no place where to send it.
I think it should be a software problem (maybe) that's why I'm asking help here.. Also, the problem with the volume slider up only occurs on W2003, not on WM5
What should I do??
Anyone?? HELLOO?

i've had this problem for a long time, and tried so many different patches non worked, but there is a way to deal with this issue u need to keep ur bluetooth on all da time or remove the file BTTrayCE from this directory
Mydevice>windows>start up
and copy this file to ur storage card if later u want to use ur Bluetooth so wat removing of this file does is that the icon in of bluetooth in tray bar will not appear automatically after u restart ur machine .
hope this helps

At no avail , but many thanks anyway.
I've seen this solution on other posts and I've tried it before. Without luck
Even the 'bluetooth on all the time' alternative. Without luck
Also, I'm now on TuMa 1.3 (WM5). The file relative to bluetooth on the startup folder is "BTIcon", wich I have moved as you stated. Without luck
Maybe the file you tell is for WM2003 ?? Could it be? Is the file named 'BTTrayCE' on WM2003 and 'BTIcon' on WM5?
I'm really desperate.
arran83 said:
i've had this problem for a long time, and tried so many ...
Click to expand...
Click to collapse

umm yeah i'm sorry, mine is running WM2003, maybe u should try downgrading to 2003 as well since i've done it and now i'm having less problems, i really don see much of advantage in using 2005, good luck.

ok here is a patch that is supposed to fix this problem but hasn't worked on mine, i just attach it here it might work on urs, or u might already have used it.

Sometime back, I had come across a post on a similar problem. I think what you have is a erratic headphone jack..I believe there is a micro (?)switch in there which connects headset and disconnects speakerphone.
I had a similar problem sometime back, and just put the headphone jack in there, jiggled it a bit and it started working. basically released the switch. your symptoms point to a similar problem...does not have anything to do with Radio ROM. Has not given me problem since then

here you go..
http://forum.xda-developers.com/viewtopic.php?t=33207

Yup, I've seen this forum before. If it has to do with a headphone problem, then It shouldn't be heard anytime, and I CAN hear music and such from the device when it isn't in a call. Anytime I put the device on the "call" state (dialing, connected, hold, etc..) the sound goes out. :-S
So, it should not be a headphones problem.... should it??
deepakr said:
Sometime back, I had come across a post on a similar problem. I think what you have is a erratic headphone jack..I believe there is a micro (?)switch in there which connects headset and disconnects speakerphone...
Click to expand...
Click to collapse

Yes, I will, for nth time... No solution yet... I will apply the Unidirectional patch again on WM2003 to see... Keep you posted..
arran83 said:
umm yeah i'm sorry, mine is running WM2003, maybe u should try downgrading to 2003 as well since i've done it and now i'm having less problems, i really don see much of advantage in using 2005, good luck.
Click to expand...
Click to collapse

OK, I've tried, for nth time, going back to WM2003SE (112 T-Mobile) and applying the unidirectional patch I've found here (I think is the same posted on the I-mate site I've tested before) and NOTHING changes...
Still the same problem.
Any clues?

hi !
try like me... in bt setting-->accessibility-->disable all access options..
to me this little trick cut off every problems on use the phone....
hi

OK, I'll give a try :? (Again going to WM2003, as I think is that what you have right?)

No Sound on BA
Hi there. Have pda2k, rom-1.40.00, radio-1.12.00. Have previously lost sound during call. Can be heard but cannot hear. Phone have been exchanged under warrantee, but new phone developed same problem after using BT to connect with PC. Currently I turn on the speakerphone in order to converse. Any help?

Re: No Sound on BA
I can not turn on the speakerpone.....
pjax said:
Hi there. Have pda2k, rom-1.40.00, radio-1.12.00. Have previously lost sound during call. Can be heard but cannot hear. Phone have been exchanged under warrantee, but new phone developed same problem after using BT to connect with PC. Currently I turn on the speakerphone in order to converse. Any help?
Click to expand...
Click to collapse

I also have a similar problem - when in phone mode, other side can hear me but i cannot hear them, if i plug a headset with microphone the other side hear me and i also have sound from other side.
if i unplug the headset, i cannot hear the other side but the other side can hear me.
are there microswitches inside the headset plug for both microphone and speaker (two microswitches) ?
thanks, yol.

Problem when upgrading from TuMa v1.3 to Helmi, no phone?

Hey All-
Rather then adding to the large Helmi thread, I figured it would be best to start my own...
In short today I upgraded from TuMa v1.3 to Helmi's new ROM: Helmi_BA_WM2k5_AKU_2.3_32mb_v1.rar
Everything went fine during the upgrade, I set the Operator Code to T%CID? which was retrieved by using GetDeviceData.exe and the upgrade went smoothly... but now the phone functionality doesn't work at all. I've tried with two different SIM's, one being a T-Mobile and the other a Cingular. Both just show no service when inserted, although if I place those SIM's into other phones everything works properly without issue and I get 'full bars' (I have another Cingular 8125 and a T-Mobile SDA).
Here is what I have done so far:
- Reupgraded the Radio to the latest rev 1.15
- Recreated the nk.nbf again with retyping the operator code
- Reupgraded to the ROM to Helmi's
- Reunlocked SIM with xdadev_all_unlock-v1.5.exe
... and still no phone service.
Any suggestions on how to get the phone functionality to work properly? Its pretty much useless right now...
Thanks!
tempie23

I'm not sure that T%CID is right for an operator code... I know for O2 UK it's O2___001 and I'm sure a T-Mobile code isT-MOB101, both of these are 8 digits... check you're devicedata output again and use the setoperator.bat to set it properly, then try again
It's all good clean fun

spkr4thdd
I have the same operator code T%CID? but only on WM5. When i use 2003SE it is DANGA001.
tempie23
I had such error on TuMa 1.4 but reinstalling the ROM helped for a while. Then I tried helmi's ROM and the problem gone. But a couple of days ago it appeared once and reflashing did not help. What I done is downgraded to 2003SE, did a hardreset and reinserted SIM. The phone came back to work. Then installed helmi's ROM again. Now it is working for a day without any trouble, HOPE it's gone forever.

Tried a few things...
I tried downgrading and then reupgrading, but it still is stuck. No phone service. Interestingly enough the LED for the phone doesn't even come on anymore.
Interestingly enough when I select the phone settings from the upper menu I'm getting a Popup message stating "The phone is not ready. Wait 15 Seconds and try again." Obviously waiting 15 seconds does nothing...
Any other ideas?
Thanks!
tempie23

sometimes (happened to me) the operator info corrupts when upgrading to WM5
copy the files attached to the update directory and run 'MaUpgradeUt_noID.exe'

spkr4thdd said:
I'm not sure that T%CID is right for an operator code... I know for O2 UK it's O2___001 and I'm sure a T-Mobile code isT-MOB101, both of these are 8 digits... check you're devicedata output again and use the setoperator.bat to set it properly, then try again
It's all good clean fun
Click to expand...
Click to collapse
No it is not, it sounds like he has the same SX 66 that I have.
The ID is = AT%CID?
I posted this in this thead Here

read my above post, it can happen to anyone when upgrading to any wm5, mine happened the very first time i upgraded (TuMa 1.3), i dont know how it happens, but it seems to be permanent even with further reflashes (haven't tried 2k3)

NO Service
Midget_1990 said:
read my above post, it can happen to anyone when upgrading to any wm5, mine happened the very first time i upgraded (TuMa 1.3), i dont know how it happens, but it seems to be permanent even with further reflashes (haven't tried 2k3)
Click to expand...
Click to collapse
HI.
Sorry for my post, but I did not "get" how to fix the "NO Service" error:
This is what I've done today with Helmi_BA_WM2k5_AKU3.5_v1.4.CF2 by baniaczek:
Hi all.
Today finally spent some time, trying to upgrade my Qtek 9090.
Everything went fine:
1st) Did a SD backup of my current settings;
2nd) Updated ROM with SetOperator to my Operator (got from getdevice.txt);
2nd) Updated without problems;
Then used the Qtek by 5 minutes (inclusively i did a phone call), after that could no longer get the "phone" working - exactly when I received a call, the phone "gone out" and never more. After several soft resets and hard resets the phone was always with "no service" message (but strangely, I could go to settings phone, and look for "the broadcasting" networks).
I swaped the SIM to another phone and it was working, never the less I got another working sim, but the problem continues (btw, I always have the PinCode disabled, and I remember now that I forgot to test enabling PinCode request!!!).
Then, just in case I downgraded the phone to W2003SE, again, and everything was working fine.
My radio was 1.12. So upgraded radio to 1.15, and started over again but with no sucess.
When I downgraded once again, the Qtek works fine with either RADIO versions or sims.
Has anyone got this "nice feature"?????
Is there any overcame solution? (My only missing test is to enable Pincode, and test if it works?)
tks for any help

I'm having the same issue here as well, tried the comm manger on and off and disable and enable it. Still makes no difference, someone please help me out, I can't get anyone to help me

PLEASE HELP!! cant connect to the network :(

Hey everyone ..
i was using my Blueangel normaly and so happy with it until i faced this problem before 2 days ..
I was texting my gf while i was out and kept on even though the battry gave me a warrny that its really low .. i ignored and kept SMS's her until it went off.
i went home charged my device but its not connecting to the network. it shows either "No Service" (where it shows X beside the signal tower) or "Searching" (where it shows ! beside the signal tower).
Please anyone knows how to turn it on im really in a bad situation here.
Note: just to let you know im using WM5 Hemi's rom and upgraded it today to Xplode's rom just hoping it would help.

Well when i tried another sim on my blueangel it worked and my sim card on another mobile it worked also. im really losing my brain

44 views no one have a slight idea..
anyways thanks alot everyone for visiting

Hi,
All I can suggest is to re-install radio rom! prob 1.15.
If not that then ensure flight mode is NOT active, and battery's fully charged
Also when you reset BA, on first screen does the R show a none?
If so reset, twice, its a common problem with BA and WM5, it isn't able to intialise the radio rom before WM5 boots.
It seems wierd that another sim worked on your BA, must be a faulty/damaged sim.
I also note you've tried the non-working sim on another phone and that works! Wierd that too!
Hope that helps,
Sunny

Have you tried to manually select the network in the "Phone" settings screen? I've heard of similiar problems being fixed by that.

well after i asked here and there and got disappointed with I-Mate people.. they know nothing at all
an IT in my company told me the problem is with my sim card. its damaged cause of the change in the battry power (as he says) it damaged the frequency that my mobile use to read the sim so there for it would work on any mobile except mine.
so i would change the sim but it needs me ages to get free and do that.
THANKS ALOT TO EVERYONE ATLEAST READ MY THREAD OR TRIED TO HELP
YOU GUYS HERE ARE THE BEST

By the way
sunny: the Radio is already 1.15 from ages. but thanks alot for trying to help me.
Fraser: I tried to manualy select the network but it says there is no network which is funny cause there is 4 networks in my area.. actuly im working with the same operator so im inside the tower LOL. the signal streth is the best here.
Thanks alot mates

No problem!
Thats what we're here for!
Regards

Same problem
I once had the same problem. Now I'm no genius when it comes to these phones and it actually took me a whole week to get an idea of what the hell happened to my phone. Basically, these phones are Quad Band (GSM 850/900/1800/1900) and for some reason after I upgraded I lost my signal. I found a little application that let me reselect my band (its not built into windows for some reason) and that solved my problem. I just selected "Auto select" and the problem was solved after a soft reset.
Now, I can not remember what that application was but maybe that can give you an idea of what to search for.

No Service issue
sunnyd24 said:
Hi,
.......
Also when you reset BA, on first screen does the R show a none?
If so reset, twice, its a common problem with BA and WM5, it isn't able to intialise the radio rom before WM5 boots.
...........
Hope that helps,
Sunny
Click to expand...
Click to collapse
Hi, is there more 'democratic' way to resolve this issue than reseting BA twice?
After installation of xplode's R4 for noobs an old version of R 1.06 was left on BA. Thinking that this was a reason for No Service of the phone I dumped latest R , but double f..reseting necessity still persists ...
Is that a normal thing to reset twice such an advanced device when you want even just to call smbdy? Thanks

there is a lil bug in my roms, after totally draining both bateries when you power it on it says NONE for radio you have to soft reset it again in order to work. I have never had a band selection problem but it is possible reason for this

xplode said:
there is a lil bug in my roms, after totally draining both bateries when you power it on it says NONE for radio you have to soft reset it again in order to work. I have never had a band selection problem but it is possible reason for this
Click to expand...
Click to collapse
Hi hi there! First of all please accept my deepest appreciation for such a great work you have done to make us - PPC ordinary users - little bit more happy Just one small note - is it possible to upgrade your downlodable R4 file with all necessary ROMs - Radio, etc., etc. With the intention that every Noob trying to upgrade his/her BA, should do it in a push of one button - not searching for separate latest ROMs and HowTo instructions? Thanks for your time!
P.s. Sorry it seems came out little bit off topic....

well it is possible but i have no time to do it. or you can try to copy the radio nbf file into the folder of the nk.nbf and run the upgrade utility

Any solution on this matter ? I am using Helmi MW6 ROM with radio 1.15.00 and i'm having the same problem.
I've searched the forum but found no solution yet.
JP

help! phone isn't working properly :(

Hi all, had my Kaiser a while now and have been using a few different ROMs in this time which have all worked great! The last ROM I used was HyperDragon III. It worked fine for a few days, then started playing up massively. It intermittantly works - Some times I won't receive anything for 3-4 hours, then receive loads of texts and missed calls at once.
T-mobile checked the network, etc. and everything was fine. Re-flashed it back to the original ROM from on here (T-Mobile UK) and it's still playing up the same!
When I put my SIM in a different phone, it works perfectly.
What else can I do/try? I *think* I flashed back to the right radio too but not 100% sure. How do I check what radio/rom versions are currently on the phone?
Thanks!

Radio version can be found @ bootup R: , remeber that the recomended radio may not apply to you as there region specific, so the best bet is to look @ people sigs in your area and see what radio they are using?
Your in the UK try 1.70.19.09 on cooked ROM it's what i always use

R:1.27.15.32
G 22.51.88.13h
D 156.00.00
That's what I got on startup.
For some reason too, when I restart the phone, before it comes to that screen it shows the Hyper Dragon screen first!
I'll try a different radio and ROM then I'm worried it's not a fault with the actual phone..

never mind, advice already given

Well I've upgraded to 1.70.19.09 Radio and Anryl Ultimate Release 3.
Phone seems alright after 20 minutes, but it'll need a few days of testing.
It's not looking good so far - I've just soft-reset my phone and it set the time back to 13:32.. Which certainly isn't the time! It was doing this before when it wasn't working properly too.
This ROM seems incredibly buggy too! Opera keeps closing itself, as well as a few other programs.. randomly!
Help please! I'm frustrated.

jamiepyrite said:
Well I've upgraded to 1.70.19.09 Radio and Anryl Ultimate Release 3.
Phone seems alright after 20 minutes, but it'll need a few days of testing.
It's not looking good so far - I've just soft-reset my phone and it set the time back to 13:32.. Which certainly isn't the time! It was doing this before when it wasn't working properly too.
This ROM seems incredibly buggy too! Opera keeps closing itself, as well as a few other programs.. randomly!
Help please! I'm frustrated.
Click to expand...
Click to collapse
Some times if you don't do a hard reset right after flashing successfully, before the phone set up, things will act buggy. Make sure you do the hard reset.

jamiepyrite said:
Well I've upgraded to 1.70.19.09 Radio and Anryl Ultimate Release 3.
Phone seems alright after 20 minutes, but it'll need a few days of testing.
It's not looking good so far - I've just soft-reset my phone and it set the time back to 13:32.. Which certainly isn't the time! It was doing this before when it wasn't working properly too.
This ROM seems incredibly buggy too! Opera keeps closing itself, as well as a few other programs.. randomly!
Help please! I'm frustrated.
Click to expand...
Click to collapse
This should do the trick. I think the recent Hyperdragon Roms are WM6.1 and the radio you had listed is for WM6.0. This can cause all sorts of hangs/volume problems etc. Also check which SPL version you have - A WM6.0 SPL can also cause hangs etc if used on a WM6.1 rom.
EDIT: sorry, only read the radio bit of the fix.
Make sure you get rom/radio and SPL all matched ie WM6.0 or WM6,1. Most of the latest roms are WM6.1. If you find Anryls rom buggy, just try another one - I love the Garmin series.

Thanks for the advice How would I check which SPL I'm on?
Unfortunately I've hard reset it with Anryl and still running terribly. Lost the network this morning too so I received a text a few hours late.
I think I'm just going to go with a ROM that's as lite as possible now!

Sorted - I've upgraded to Hard SPL 3.28 and I'll flash the ROM to something lighter. Thanks guys

It appears to be working fine except I'm still having the problem of it changing the time!
Just checked the phone and it's saying 16:50.. Although half an hour ago it read the correct time. Any ideas?
I'm using Galarm 1.4 if it makes a difference. Running Athine Lite now.

Sorry everyone - Phone still isn't working properly. On the correct SPL, correct radio and correct ROM.. done a hard reset.. And it still just keeps losing network! Think my phone might be broken in some way?
I *assume* it's under warranty.. I got it under a year ago, but got it due to an insurance claim of my Hermes, they replaced it with a Kaiser.
When I phoned T-Mobile, they said although I got it from the t-mobile store, I'd need to speak to my Insurance company.
BUT I'd need to put it back to standard for Warranty purposes! I've no idea what I'd need to go back to..
thanks everyone

bump - anyone?

jamiepyrite said:
BUT I'd need to put it back to standard for Warranty purposes! I've no idea what I'd need to go back to..
thanks everyone
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs