Hi everybody,
I've got problems with connecting my Rikaline 6010 to the Car Kit. With the help of the forum I know now, wich pins I have to connect together. But I'm not be able to bring power to the Mouse. I have the +5V and GND connected but the LED on the mouse won't turn on. With a simple car adapter for the mouse and the xda it works perfect. I try to look inside the cable of the car adapter and it looks lite the cable, I build myself.
Maybe I have to short some pins inside the connector ??
Does anybody have a Rikaline 6010 successful connected to the xda car kit ?
thanks a lot
rob.
Make sure the switched power supply is connected.
I assume you are using the official XDA carkit.
I did some reverse engineering on this carkit and found that the GPS powerline is only working if the switched power line for the carkit is connected.
After disconnecting this line the GPS power will stay on for 1 hour and then automatically switch of.
Have you checked if there is power on the GPS connector of the carkit when nothing is connected? Maybe the current demand is to high? For pinlayout check www.vanhemert.biz
Francois
Hi Francois,
I think my problem is not the car kit. After it doesn't work with the carkit, I tried to connect my car-adapter-cable with the cable, I made myself to the gps-mouse. And also there, the mouse doesn't get power. So I simply put +5V and GND to the pins of the mouse-connection and it doesn't work.
Maybe GND must be connected to two pins or to the GND-pin AND the PS2-connector's metall ?
I think, I have to buy a H203e to make it work....
rob.
Pinlayout
I have looked at the data sheet (http://www.rikaline.com/pdf/gps-6010-manual-e.pdf) and it looks straightforward. Pin 2 and 4 should do the job but I can imagine that you need a correct RS232 signal to get the thing up and running. Are you sure that the LED is just an indication of power or does it only light if power and RS-232 is correct?
As you can see in the schematics on my website I had trouble opening the COM port on my XDA, Communication just did not start unless I pulled the DCD line (pin 6) to Vcc. This will activate Active sync in the same way as the original cable set I used to have.
Good luck,
Francois
Hi,
thanks for your reply. The LED on the GPS-Mouse have to turn on simply by bringing power to it. I've tried that by using my car adapter cable and simply connect the mouse to the cable and not connect the xda...and the LED turns on.
I've ordered today a Hi203E and I will try to conncet it as you described on your homepage....hope it will work (if not, I'll be back ;-))
thanks a lot
rob.
Hi Francois,
today I received my Hi203e and I will try to connect it to the carkit.
One Question:
Is the connector, which is shown on your homepage and labeled with "to gps" the female connector, which is wired to the gps-mouse or the male connector, which is wired on the selfmade cable between carkit and PS2-connector of the mouse ??
thanks
rob.
hi,
ok, my previous question is now obsolet. The connector, which is wired to the Hi203e, is male (at my Rikaline6010 it is female). So I have to buy a female connector and build new cable. I made a first test by bringing the +5V and GND of the carkit over an adaptercable to the gps-mouse and (yippie) it worked. The LED on the mouse turns on !! Looks pretty good.
...to be continued (if I have the new connector...)
rob.
Hi Francois,
I've got it now and it works perfect. Thanks again for the Info's on your webpage.
2 points:
I've got a low noise (frequently repeated) in the speaker, when the gps is active. Is there something to do against that ?
And how can I stop the activation of active-sync, when i put the xda into the carkit ?
Do you know that ?
thanks
rob
noise...
rob said:
I've got a low noise (frequently repeated) in the speaker, when the gps is active. Is there something to do against that ?
Click to expand...
Click to collapse
I would guess this is the speaker wire picking up the GSM signal, nothing to do with the GPS. Try re-aligning so that the wires relative to the antenna of the XDA. If that doesn't work, you could experiment with ferrite beads (these ugly black blocks on all modern cables) on the wires.
Same problem here, but...
I found that if I start serial communication with the GPS unit, i will hear some interferance via the speaker. It looks like the auto mute functions does not work immediatlly after inserting the XDA and "the connection is left open".
Workaround:
Pressing the red phone button to generate a tone (keypress) activates the automute and the interferance will disappear. (at least is does in my case)
Auto start of the active sync process:
This is caused by the DCD line pulled to Vcc. I first owned a standard GPS Y-cable (XDA/GPS/Lighter) and it showed the same behaviour. My first experiment was to not use the DCD line (just gnd, tx and rx)but at that time TomTom could not open the COM port. I did no further investigation but one of the forum members suggested to disable the IR connection and auto sync, this should free the com port to TomTom and not start active sync automatically. Again I have not tested it but if you will, i am interested.
Good luck,
francois
hi,
Been reading this thread with alot of interest...
can someone help me with a problem, I have the O2 carkit installed in my car, and i also have a rikaline 6010 that i would like to attach it.
I have found the GPS connector that i need to attach the GPS reciever to but when i check the connector for +5v its not there...
Does anyone know where i can connect it to... looks like the person who connect my carkit could'nt be bothered about connecting up the GPS connector properly...
and also the colour of wires that everyone mentions, mine are a different colour...
i have the following from my rikaline reciever, 4 in total...
red
black
green
white
does anyone know what connects to what????
Many Thanks
Zetex
Rikalinegps 6010 with cables - from eBay
This receiver is available with cable for XDA via eBay (see link below), but you guys have got me worried. I'm thinking of buying the Rikaline 6010 but am I going to have to do all this business of rewiring etc? What's the economical way of buying all the other bits that I need (Software, Car Kit etc)?
I'm looking for some easy to follow advice. Keep it simple please.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=4668&item=3094896604&rd=1
:? :? :?
Hallo, I'm from germany and i've got an Laptop-GPS with RS232 and PS/2 conectors and i would like to know if there is any possibility to built an adaptercabel?
Then i don't have to buy a new GPS antenna.
Thanks for answering
If your gps is made by Haicom or similar, the adaptor lead containing power and data connections are only £15 here in UK, lot less trouble than obtaining an xda connector and trying to solder the connections, if you get power in the wrong place you have no xda or gps.
Hello,
my GPS is build by GARMIN. It's a GPS 35-LVS. I don't know, if it is similar to a Haicom. Maybe anyone else knows it.
You can use a serial cable + null modem adapter which is no problem.
The biggest problem for you is how to power the GPS.
I understand it is normally powered by PS2 so you need to find an adapter so that you can power it in car or use batteries.
You may be better off buying another GPS.
Hi PC-Mobile,
thanks for your answer, thats the way i supposed. In my opinion i can use a powersupply that makes 5V out of 12V. Than i get power for both, the XDA and the GPS.
Thats the cheapest way for me, the null-modem cabel i can build myself and seriel cabel is easy to buy.
Look here.
Regards, Tore
Can anyone help ???
I am trying to connect my GPS receiver to my car kit. There is a 9 pin connector which is not described. Does anyone know the pins for txd/rxd &gnd.
jester said:
Can anyone help ???
I am trying to connect my GPS receiver to my car kit. There is a 9 pin connector which is not described. Does anyone know the pins for txd/rxd &gnd.
Click to expand...
Click to collapse
Take a look at
http://www.vanhemert.biz/Car_Kit_GPS_Connection.htm
HTH
Stefan
hi
i lost my USB for PC cable for jabra bt 8010.
please help me, show me what cable i can buy to replace it,
it seems that it can use some other cable to replace.
could you help me
so thanks
could i use the USB for PC cable for BT330/BT500/BT800/JX10/BT 8040 for BT8010.
or could i use universal usb cable which has the same size for this one?
because I tried to find out cable but failed, no one sells that.
please help me to answer this question.
thanks so much
hi, just like you i also need usb cable for my 8010. ive googled high & low but to no avaiL? especially as im in the Philippines . . maybe by this time you have new info? pls help & thanks
Its just a usb-to-micro-usb cable.
thanks, but the micro usb's available on ebay are for motorola & looking at the pics -> - > they look different . .
Micro usb is micro usb. Its a standard.
usb may be a standard, but ...
... apparently the cable ends are not. I've have three different Jabra headsets in the past several years, all of which used a usb charging cable and none of the usb cable ends on the headset side were compatible with each other. I made the mistake of ordering off ebay and the cables I received did not fit my 8010. My advice: Don't buy a usb cable unless the seller can confirm that the cable works with your particular headset.
@kihoalu
thanks very much. if you get wind of a supplier, pls post. im sure there are others who also need this cable
I wish I knew why yours are all different, my 8010 came with a standard micro-USB port. The charger and the computer sync cable are quite normal.
i have kaiser at&t us vertion
i need to use Headphone on it
can any one help me
plug in a headset or buy a bluetooth one.
You need an adapter. Take a look here:
http://store.wmexperts.com/att-tilt-headset-adapters.htm
Good luck.
Headphones
It really depends upon what type of headphones that you have.
There are headphones available that will plug directly into the Kaiser's serial port.
But if you have the headphones that have a round plug, then you would need to purchase an adapter in order to use it.