Related
Hey Guys....
I am still working on this DIY but this is how I was able to accomplish reverting back to my OEM Cingular 8125 state.
If someone could plase let me know how to replace the very first SPLASH Screen from "HTC" to CINGULAR, I would greatly appreciate it.
By following the steps below, you will have almost everything back to its original state.
Be sure to download all the necessary ROM files: OS ROM, Radio ROM, splash.bin
Place your OS ROM and Radio ROM inside the c:\sWizard\ROM folder.
DOWNGRADE YOUR OS AND RADIO ROM
1. Download aWizard 1.3b Beta Version (Attached File or Latest Version) from the following link: http://forum.xda-developers.com/viewtopic.php?t=37386&highlight=awizard
2. Unzip the folder to your root directory (C:\aWizard or D:\aWizard). You need to avoid having spaces your directory name. This is the reason placing folder in the root.
3. Make sure you have an active connection via Active Sync.
4. Run the aWizard.cmd file from C:\aWizard
5. Run "e" command FIRST !
6. Run "u" command. Your Wizard will reboot.
7. Run "w" command to update your ROM. You will get a prompt to choose your ROM. If you did not place a valid ROM inside the ROM folder, then you wont see it from this list. Also, if you placed your aWizard in other directory with spaces (i.e C:\ MY DOCUMENT) then you wont see it either. Just let it run. It will take close to 20 minutes. At the end, it will as you to hard reset.
8. Run "r" command to update your Radio ROM. Same as Step 7.
Replacing Splash Screen (Back to Cingular)
1. Place the splash.bin file inside the c:\aWizard\lib
2. Open up CMD and navigate to c:\aWizard\lib
3. Type in the following command "pdocwrite.exe -n 1 splash.bin 0x002d0000"
pdocwrite.exe = this program is located inside the LIB folder
splash.bin is a file that I converted.
4. Once completed, please reset your Wizard and now you will have Cingular's Splash (2nd Splash)
Updating the EXT ROM
1. I did this manually by utilizing Active Sync to copy over all the Cingular ROMs to the Wizard and running it individually.
2. Reset and you will now have all the programs Wizard came with.
FAQ
Q. My Wizard is stuck on a splash screen and it wont do anything.
1. Hard reset your Wizard
2. Hold onto Camera Button while turning on the Wizard and you will get the boot screen.
3. Plug in your USB Cable
4. Run one of the known ROM files with .exe extention. When this happened to me while downgrading,
I had to reload the latest iMate ROM.
5. Start the downgrade process again by following the above instruction.
reverting back to original cingular rom
Thank you for this.
Don't you have to REINSTALL original Cingular Rom or does this do that by removing imate updated ROM?
js
Re: reverting back to original cingular rom
urologyhealth said:
Thank you for this.
Don't you have to REINSTALL original Cingular Rom or does this do that by removing imate updated ROM?
js
Click to expand...
Click to collapse
When you install Cingular ROM, it will remove/overwrite the existing iMate ROM.
Be sure to place your ROM files in the the ROM folder.
If your running the aku2 imate rom, many people will have problems running awizard or lokiwiz to unlock the CID, I had to run the tmo uk rom update (.exe one) which replaced the imate, and then restore the rom files I had backed up for cingular, although the extended rom is still locked, thats annoying.
jvanbrecht said:
If your running the aku2 imate rom, many people will have problems running awizard or lokiwiz to unlock the CID, I had to run the tmo uk rom update (.exe one) which replaced the imate, and then restore the rom files I had backed up for cingular, although the extended rom is still locked, thats annoying.
Click to expand...
Click to collapse
can you please share how you change the very first splash screen on your 8125 ? its the only thing i wasnt able to do or know how to do.
thanks
FarSeide, I'm pretty sure that even the stock 8125's from Cingular showed the HTC screen first, the cingular screen second, and finally the Windows Mobile screen. If that's the case, then your 8125 is as good as new as far as Cingular is concerned.
Also, if anyone upgraded to the AKU2 I-mate ROM, you cannot do the process you described, because (as someone else mentioned) the lokiwiz program will not work. What you need to do is FIRST install a different ROM using an exe file (a good example would be the leaked AKU2 Q-Tek ROM exe file), and only after that entire upgrade process is completed, can you now use lokiwiz to unlock the SuperCID and install the Cingular ROM.
kingbear2 said:
FarSeide, I'm pretty sure that even the stock 8125's from Cingular showed the HTC screen first, the cingular screen second, and finally the Windows Mobile screen. If that's the case, then your 8125 is as good as new as far as Cingular is concerned.
Also, if anyone upgraded to the AKU2 I-mate ROM, you cannot do the process you described, because (as someone else mentioned) the lokiwiz program will not work. What you need to do is FIRST install a different ROM using an exe file (a good example would be the leaked AKU2 Q-Tek ROM exe file), and only after that entire upgrade process is completed, can you now use lokiwiz to unlock the SuperCID and install the Cingular ROM.
Click to expand...
Click to collapse
Eli,
thank you for the info. I wanted to put this together because when I tired to do this, there were information but scattered all over all forums. just wanted to help others so that they dont go through the same thing i did.
i was following these instructions and i got a
NOTIFICATION ERROR
cannot execute repllog.exe
so what i had to do was hard reset, boot screen , re-installed imate, ...
i guess i will try it again, what do you guys think
hmmm... sorry to say but my 8125 only ever showed the cingular splash. No HTC, no WinMob. I had assumed that Cingular somehow replaced all 3 splash screen with theirs.... In fact, I never even knew there was more than one splash screen until I upgraded to the Qtek rom.
I'm in trouble
I tried to downgrade the ROM and now I'm hung in the i-Mate SPLASH SCREEN. I tried the hard reset and it hangs every time. I can't get a connection through active sync obviously so what are my options. How can I get a working device.
I'm freaking out.
Please HELP!!!!!!!!!!!!!
Re: I'm in trouble
hellomoto_25 said:
I tried to downgrade the ROM and now I'm hung in the i-Mate SPLASH SCREEN. I tried the hard reset and it hangs every time. I can't get a connection through active sync obviously so what are my options. How can I get a working device.
I'm freaking out.
Please HELP!!!!!!!!!!!!!
Click to expand...
Click to collapse
relax... i was exactly where you were...
first, hard reset your device.
Hold the Com Manager, Voice Command and press the soft reset with your stylus.
before you turn the device back on, hold the camera button then turn on the power. you will receive the boot screen. Plug in your USB Cable and kick off the EXE file. Load one of the known ROMS like the iMate ROM.
reload and try again. I am willing to bet that you disconnected the USB Cable while updating to Cingular ROM.
Good luck and dont worry.
does anyone have the exe for the original Cingular ROM ?
my colleague tried to update his 8125 with my imate rom.....and did not unlock it first.
all he has is the bootloader now, the update gives the well known Error: Invalid Vender ID
Any help is greatly appreciated
Thanks !!
Get a copy of the proper ROM on a SD card, and reload it that way.
This is the easiest way out of that box......
Thanks,
but how to get the Rom reloaded from the SD card onto the device using the bootloader ?
dirty_harry said:
Thanks,
but how to get the Rom reloaded from the SD card onto the device using the bootloader ?
Click to expand...
Click to collapse
THAT part is easy.
Note that the SD card image is NOT a file. You have to raw write it onto the card, which will destroy the filesystem - so back up the card first! psdwrite will do the job. You also need the image (PREVIOUSLY copied from a SD-made backup with "psdREAD")
To restore it, insert the card, hold the CAMERA button, and power on. The phone will tell you to press VOICE to restore the SD image (it looks to see if there's a valid one in there)
Note that with 1.x bootloaders this will happen with the BACKLIGHT OFF, and you only have 3 seconds or so to press the key - so have a flashlight handy. 2.x bootloaders turn the backlight ON.
Hit VOICE. The image will be verified (checksummed) and if it is good, it will be loaded.
That's it. Takes about 2-3 minutes. When it finishes it will tell you to press any key, and when you do you'll end up at the tricolor screen.
Power off and back on, and the phone will cold boot the new image.
This will work even if you can't run an RUU loader, so long as you can get that first prompt up. It is a VERY effective rescue method.
IMHO before you hack on the firmware in these things you should make an SD card backup just for this reason.
Which tools is best option for ROM backup to Mini SD?
Hi,
Just read your message about writing ROM to Mini SD card.
I'd like to do just that.
I want one or two ROM's for safekeeping stored somewhere instead only a backup or official copy on my pc.
As i've read restoring from SD is safer and faster..
I don't intend to use the SD card for anything more than just that.
In the Prodigy Service Manual (Prodigy Service Manual -XA(0813-2005).pdf) HTC uses mtty.exe. There are also instructions in the PDF.
Since HTC uses this, it should do exactly what i want, i guess?
Or is there a better tool?
Thanks,
Allegro.
P.S: Will a restored ROM from Mini-SD look fresh to HTC?
Or will they see it's a self restored copy instead of a official HTC restore?
Will it reset "everything"?
I was able to fully restore CIngular 8125 ROM, EXTROM, All Splash Images using the SD Restore.
100 Cingular OEM Spec has been restored...
I hv updated T Mo custom ROM..but now can't downgrade even by Awizard utils....can any one throw some light on this?
Hope you guys can help me out. I disassembled my Cingular 8125 to try and improve the earpiece speaker. I put the device back together and turned it on and it sticks on the boot screen.
When I try to do a hard reset, I get to the point where I have to press send (green button), but then displays the following for a second and then goes back and freezes on the boot loader screen:
format FAT partition
format is complete
I've read some stuff about being able to recover from this using the SD card, but I'm not sure how to do it. If it is possible to recover from SD card, can someone please upload the appropriate files to the ftp site?
Please HELP!!! My ROM versions are below:
IPL: 2.16
SPL: 2.16
GSM: 02.07.10
OS: 2.16.9.1
Thanks!!!
Update:
I'm able to get to the mutli-colored screen by holding the Camera Button prior to starting the Wizard back on. I plug in my USB to my computer, but my computer says "USB Device Not Recognized". How can I get a new ROM on to my device? I tried running the ROMUpdateUtility.exe from a ROM, but it obviously wouldn't work because my computer doesn't see my phone. Please help!!
Thanks!!
Update #2:
When connected to the computer, I got to device manager and see an unknown device under USB. I uninstall the device and do a scan for hardware changes. This finds the phone, but it still shows up as an unknown device. It does say that device is ready to use, but when i try to run the ROM update utility, it still cannot find my phone.
Do I need special USB drivers for the phone to be recognized?
Please guys, any help would be greatly appreciated!
Thanks!!!
you shouldnt need any special driver for your computer to connect to Wizard.
did you install ActiveSync at all ? perhaps its using the driver from that installation....
What OS are you using ?
Yes, I've previously installed ActiveSync 4.1. I am using Windows XP. Would it help to try to uninstall/reinstall ActiveSync? I may give that a try. Will keep you posted. Any other suggestions?
EDIT:
Just tried to uninstall/reinstall ActiveSync and it still says USB device not recognized
it looks like a dead ROM, hope it has nothing to do with the hardware.
Anyway, you try looking through this forum, there are some people who've got stuck on the boot screen, and did a flash (via the bootloader screen, e.g. the multi colour one) on the ROM and seems to fix the problem. Probably you want to put this option last. Mean while, wait for others to repsond, and you may well start looking on how to flash the ROM from bootloader screen.
hanmin said:
it looks like a dead ROM, hope it has nothing to do with the hardware.
Anyway, you try looking through this forum, there are some people who've got stuck on the boot screen, and did a flash (via the bootloader screen, e.g. the multi colour one) on the ROM and seems to fix the problem. Probably you want to put this option last. Mean while, wait for others to repsond, and you may well start looking on how to flash the ROM from bootloader screen.
Click to expand...
Click to collapse
Thanks for responding. I'm ok with having to reflash, but the problem is that my computer doesn't seem to recognize my device when i'm at the multi color screen.
Isn't there a backup battery in these devices? I had my Wizard disassembled for 4 hours. I guess the backup battery could have died during this span, but even if it did, what implications would that have?
You still have hope
Get it to the bootloader screen. Connect via USB to your PC (make sure you have active sycn installed) and run an RUU to replace your ROM. I had to do this after trying to downgrade to the original Cingular ROM on my 8125. Scared the S*!T out of me when it hung on the Splash screen and wouldn't load. I thought it was toast but using the Bootloader and an RUU it put it back to normal again.
It won't look like the PC is recognizing the device but it will as long as its in Bootloader.
Let us know if you get it fixed.
Re: You still have hope
hellomoto_25 said:
Get it to the bootloader screen. Connect via USB to your PC (make sure you have active sycn installed) and run an RUU to replace your ROM. I had to do this after trying to downgrade to the original Cingular ROM on my 8125. Scared the S*!T out of me when it hung on the Splash screen and wouldn't load. I thought it was toast but using the Bootloader and an RUU it put it back to normal again.
It won't look like the PC is recognizing the device but it will as long as its in Bootloader.
Let us know if you get it fixed.
Click to expand...
Click to collapse
Thanks for the reply. The problem is that when I plug the device into my computer, I get a USB device not recognized error. I try to proceed with ROMUpdateUtility.exe anyways, and get this error:
"The update utility cannot connect to your PDA phone..."
Seems like updating via USB is not going to work for me. Can I write a backup to the SD card from the PC, put the SD card in the phone, and then boot from there? I've read some posts along these lines, but detailed steps would be very helpful. THANKS!!!
You need an SD card dump image.
This is NOT a file in the sense of a file on the SD card. Its a RAW image. You need someone who has dumped their firmware in that fashion to send you the SD image.
You then write it onto the SD card using something like "psdwrite" (which will, by the way, DESTROY the filesystem on the SD card - don't have anything on there you care about!) and then insert it into the phone with the power off. Hold the CAMERA button and turn it on; when it asks if you want to restore the image, hit VOICE.
Note that for 1.x IPLs/SPLs the backlight will be OFF during this procedure, so you have to pay attention and/or have a good flashlight handy.
Genesis3 said:
You need an SD card dump image.
This is NOT a file in the sense of a file on the SD card. Its a RAW image. You need someone who has dumped their firmware in that fashion to send you the SD image.
You then write it onto the SD card using something like "psdwrite" (which will, by the way, DESTROY the filesystem on the SD card - don't have anything on there you care about!) and then insert it into the phone with the power off. Hold the CAMERA button and turn it on; when it asks if you want to restore the image, hit VOICE.
Note that for 1.x IPLs/SPLs the backlight will be OFF during this procedure, so you have to pay attention and/or have a good flashlight handy.
Click to expand...
Click to collapse
Genesis3,
Thanks for your wonderful insight. I really appreciate your help.
Now can someone help me with getting an SD image? What constitutes an image file? Is it simply the .nbf file? Do I just use psdwrite and copy the nbf file onto the card? Is there something on the FTP site I can use? My configuration as mentioned in the original post is:
IPL: 2.16
SPL: 2.16
GSM: 02.07.10
OS: 2.16.9.1
I had a similar problem and reflashing the rom using the usb is possible. Don't use a flasing utility, though.
Find a self contained rom upgrade from the FTP. As long as you see USB on the bottom left side of your screen, it should work. After that, reflash with whatever rom you want. Hope it works. Nothing worse than an the feeling you have holding an expensive paper waight.
wireless_one said:
I had a similar problem and reflashing the rom using the usb is possible. Don't use a flasing utility, though.
Find a self contained rom upgrade from the FTP. As long as you see USB on the bottom left side of your screen, it should work. After that, reflash with whatever rom you want. Hope it works. Nothing worse than an the feeling you have holding an expensive paper waight.
Click to expand...
Click to collapse
Thanks for the reply. I'm not sure what you mean by "self contained rom". In the past, I've used K-JAM_WWE_216901_2169101_020710_ship.zip from the FTP site, and ran the ROMUpdateUtility.exe without any problem. Now, since I cannot make a connection to the computer via USB, I am unable to run ROMUpdateUtility.exe. Is there an alternative "self contained" file I can use that will work in spite of the unknown USB device message?
Thanks in advance...
try to DL this file: RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe. Its on the FTP. Follow this link:
http://wiki.xda-developers.com/index.php?pagename=BA_FTP_Site
click on the FTP Root link, navigate here:
ftp://ftp.xda-developers.com/Wizard/Roms/Qtek/ and download the file. Put the phone in bootloader, attach to PC (make sure the phone has USB shown in the bottom left corner, and run the file.
Ignore any references to ActiveSync or any connections period. Just run it all the way through the installation process. When all is done, you can upgrade, down grade, etc using the appropriate method (I use aWizard) Let me know if this helps.
Wireless One
wireless_one said:
try to DL this file: RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe. Its on the FTP. Follow this link:
http://wiki.xda-developers.com/index.php?pagename=BA_FTP_Site
click on the FTP Root link, navigate here:
ftp://ftp.xda-developers.com/Wizard/Roms/Qtek/ and download the file. Put the phone in bootloader, attach to PC (make sure the phone has USB shown in the bottom left corner, and run the file.
Ignore any references to ActiveSync or any connections period. Just run it all the way through the installation process. When all is done, you can upgrade, down grade, etc using the appropriate method (I use aWizard) Let me know if this helps.
Wireless One
Click to expand...
Click to collapse
Thanks for your reply. I've tried the course of action that you've suggested, but i cannot get through the installation process because of inadequate connectivity between the phone and my PC. I see the USB in the bottom left hand corner, plug into the PC, and immediately see a USB Unknown device error. I ignore that and try to run the ROM anyways and it fails and I get an Update Error:
"The Update Utility cannot connect to your PDA Phone. Please check that your USB/cradle is connected..."
That's why I think I got to go the SD card route, so anyone with an image file that i can put on my SD card, I really could use the help!
It is NOT a NBF file.
The problem with the 8125 is that if you are somehow not CID unlocked the wrong SD image will actually hurt you more than it helps.
You need to find someone with a Cingular 8125 SD image - I have one for the T-Mobile MDA but not for the Cingular "as-shipped" ROM.
Genesis3 said:
It is NOT a NBF file.
The problem with the 8125 is that if you are somehow not CID unlocked the wrong SD image will actually hurt you more than it helps.
You need to find someone with a Cingular 8125 SD image - I have one for the T-Mobile MDA but not for the Cingular "as-shipped" ROM.
Click to expand...
Click to collapse
Genesis3,
Thanks for confirming it's not a NBF file. I had previously CID unlocked using awizard and then installed a newer IMATE ROM:
IPL: 2.16
SPL: 2.16
GSM: 02.07.10
OS: 2.16.9.1
I did not install the IMATE Extended ROM or Cingular customizations after upgrading to the IMATE ROM. Do I still need a Cingular 8125 SD image, since i've already upgraded my ROM, or do I now need an IMATE SD image to match my current configuration? Or does the type of image file really not matter?
Thanks in advance!
I really hate to beg, but I am desparately seeking an SD image file backup. I'm going out of town in a couple of days, and would love to have a working wizard for my trip.
Can any one of you kind souls please upload your SD image file backup to the FTP site? It really is my last ditch effort before having to send the phone back.
I truly appreciate all the help and all the responses I have received to date.
THANKS!!!
sunil23 said:
I really hate to beg, but I am desparately seeking an SD image file backup. I'm going out of town in a couple of days, and would love to have a working wizard for my trip.
Can any one of you kind souls please upload your SD image file backup to the FTP site? It really is my last ditch effort before having to send the phone back.
I truly appreciate all the help and all the responses I have received to date.
THANKS!!!
Click to expand...
Click to collapse
Sunil,
i apologize for not responding your PM sooner but wasnt available due to travel plans.
I am trying to upload the files to the Upload folder now and i iwll let you know when i am done.
Thanks
getting permission denied when i tried to upload the documents.
is there another password i should be using besides xda/xda ?
Hello gays!
I hav a problem with my Mda.
In my mda was windows 05 and i want to upgrade to 06
And im download rom from thiece site:
http://forum.xda-developers.com/showthread.php?t=305125
And i Upgrade rom thiece method :
ANOTHER FLASH METHOD :
If you have the chinese WM6 rom, downgrade to some WM5 with official RUU, then:
download this:
http://rapidshare.com/files/29098553...fixed.zip.html
Once you unpack it, please put the nk.nbf (charmer wm6) into the Shelltool folder. Open shelltool.exe. Click Get Rom info, then click Extract OS. Wait until its finished and you'll receive a file called 8004000-OS.nb (save it for later).
Download the xbeta Chinese WM6 rom : http://rapidshare.com/files/27671349...eta.exe. html
Extract it and put that 8004000.OS you saved before in the XBETA directory. In the itsutils folder of xbeta rom you will find enablerapi.cab and cert_spcs.cab. Copy them to your device, install them on Device Memory, then soft reset.
run xbeta.cmd and choose the 8004000OS.nb file to flash (you should be connected with AS and have your radio module turned off).
When the screen goes green and the flashing is finished make a HARD RESET!. Press Camera and Voice Dail buttons (hold them). Put and hold the stylus in reset button for 2 seconds. Release it. Wait until you see some white fonts on black screen. Then release those 2 buttons. Push the green dial button.
I choose thiece method becouse the first method in the rom subject doesnt work.
But after im instal new rom i have Era rom and when im complete upgrading to wm6 the phone is restart and im see era splash screen and its strange for me :/
So the problem is it is in startup screen showin Era splash screen and he STOP! i tried to hard reset but it gives fat partition error.
Please HElp me!
sounds like your device is CID locked at the time you flash it.. which gives you the same splash screen. However, the fat partition error (I presume it said format fail), is a big problem that AFAIK, it has no solution.
What you can do (at least) now is to put your phone in to bootloader mode and flash it (check the wiki, I think there is a section on this).
I turn on boot loader and i upgrade to another rom Era name and still thiece same Can you give me link with rom ?? to my phone ? Yes i dont unlock the cid
http://www.tm-phonedownloads.com/download_manager_mda_com2.html
Now i download my Net is so slowly :d when im download and upgrade i write and good luck to me ;]
Rom t mobile Doesnt work. Other minds?? But the splash screen is T mobile ;]
ipl 2. 06
spl 2.06. 0000
gsm 02.19.21
os 2.6.2.27
meybe Rescue Rom like i wizard ?? do you now where i can find it??
the splash screen indicated that it has already flashed, but, as I've mentioned above, the partition failure are more complicated than that and may not be fixable yourself. I can't help anymore now, you can try to find some other solution. Good luck.
How to unlock cid ?? can you tell me what i hawe g 3 or g 4
at the top section of this screen, there is this "XDA-Wiki", go in to the 'Wizard' section. G3 G4 CID unlock info is there.
Raptorgda said:
I turn on boot loader and i upgrade to another rom Era name and still thiece same Can you give me link with rom ?? to my phone ? Yes i dont unlock the cid
Click to expand...
Click to collapse
""Splash screen freezing -> SOLUTION !!! DIY
--------------------------------------------------------------------------------
Damn... I walked around and around and solution was all near me and able to do it myself...
Ok here´s how I done it.
First, I must explain what was the problem.
After update the firmware (not actually upgrade, I had the phone full of trash, so I decided to reflash same firmware v2.18 PTG), the Qtek 9100 / HTC Wizard freezed at 2nd splash screen (the one that shows OS versions IPL version, ect). Tried many different versions, upgraded to 2.24, 2.25, downgraded even to 1.6.7.3, but always same problem, freezed on second splash screen. I read many topics on xda-dev, and seen some people with same problem. Apparently there was 2 solutions. 1- send phone back to warranty. 2- write backup ROM from SD in bootloader.
Passed more then 15 hours asking for this SD backup everywhere, and COULDN´T find any help. Apparently no one had this "SD dump ROM Backup".
So here´s how I solved my problem
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
Thanks to all and hope this helps more people with this problem""
In Wizard forum
Oszi link doesnt work Do you have other??
Doesnt work sesion like that :
r2sd all
Get_BitData
***** user area size = 0x7A80000 Bytes
R2SDBackup() - Download type = 6
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512 And stop hiere
You have Wizard but i have mda 2 compact do you now?? ;]
But i have a idea can you give me backup files?? on cd card ?? i will put it on my sd card
Raptorgda said:
Doesnt work sesion like that :
r2sd all
Get_BitData
***** user area size = 0x7A80000 Bytes
R2SDBackup() - Download type = 6
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512 And stop hiere
You have Wizard but i have mda 2 compact do you now?? ;]
But i have a idea can you give me backup files?? on cd card ?? i will put it on my sd card
Click to expand...
Click to collapse
Yes I know!I have MDA cII to and not wizard!
You must other MDA cII !your pda is dead you must other mda cII and save the rom the new mda cII.
He say maybe work other Pda (mda c,mda cII,prophet and more)
(sorry my bad english)
I will put Sd card with backup from my own wizard meybe it is will be work if not i take backup from my firend (he have mda 2 c ) Sory for my bad english!
I will put Sd card with backup from my own wizard meybe it is will be work if not i take backup from my firend (he have mda 2 c ) Sory for my bad english!
Format Is Failed (!?)
Hi. I know that the focus is now on the new ROM, but I am having a problem with my MDA Compact II after following the alternative flashing method. Original details:
IPL 1.12, SPL 1.12.0000, GSM 01.11.20, OS 1.12.2.23
All seemed to go ok, following step by step as per http://forum.xda-developers.com/attachment.php?attachmentid=39129&d=1179243687 and I got to the end step with ‘Congratulations’. I had no error messages. However upon hard reset I got the message: FORMAT FAT PARTITION, FORMAT IS FAILED (oops!)
The screen then showed the same details as before, but with OS now 10.2.0.8.
I’ve done some searching on the Forums & tried restoring the phone via bootloader using both “MDAc2_ROM_Johnnnnnnnnnny_v1.0” (stalls at 99%) and “RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship” (this completes 100% & reverts the OS to 1.12.2.23, but I get the same FORMAT IS FAILED message).
Any further suggestions how I can revert to the original state, or update to WM6?
(My wife has an MDA II as well – I’ve checked my battery in her phone & it is fully charged).
PS Ignore the details at the bottom - I also have an MDA COMPACT (I)
Chameleon846: if you read carefully, you would know that you need at least bootloader in ver. 2.x to flash WM6. And seeing you have 1.x, no wonder it didnt flash poperly. GO find an official HTC Prophet rom and flash it with RUU. It will help.
no problem with this, this happen time after time on every ppc, it's random flashing error.
http://forum.xda-developers.com/showthread.php?t=307332
please, read forums before asking, this was mentioned many times...
vlodeck, thanks. A little knowledge... I stupidly missed the 2.x bit...
I've tried the RUU method with an official ROM. It completes all 100%, but will not go any further. I've seen bits about a restore from an SD card, but can't find the exact method (copying the nk.nbf file to SD & running bootloader doesn't do anything. If I manage to sort this am I able to upgrade the bootloader to 2.x?
Thanks.
Chameleon: not charmer official ROM. Prophet ROM!
Need a favours over here. Recently, i bricked my trinity. P3600 more precisely Dopod D810 (i flashed wrong ROM -> Unpacking cooked rom for trinity but i merge it with -Hermes cmd in NBMerge! houh... so stupid! ). Soo... just not what i expected, Rom flashing stop on half, SR my trin and tada.... 3Color screen bootloader popup! haaarggg, i try flashing another rom using any rom that has same CID *official or cooked rom* (some are 100% thru, but someother not) but like usual it won't start the windows (just blank/black screen with green led[ always on!) Never been like this before! Have been flashing several times using any cooked rom by great chef on trinity but this time! :doh: damn it! my bad.
i found solution on the forum *Unbricking Trinity Stuck on Bootloader* but since my usb port can't be detected on my vista/xp machine, whether i disable AS and changed my usb cable it doesnt work at all, on mtty too! so i can't use that utility. i try run install sspl olipro 1.3 but it never changed my spl at all. now i can't use my trin at all cuz allready dead.
btw this is the info on trin 3color screen bootloader:
IPL 1.00
SPL 3.20 OLIPRO
anysolution for bringing back my trinity from the death? maybe a tools/utility to unbrick trinity from SD or something like that, which not involved any pc connection, without bring this devices to htc center of course.
I hope any expertise on this forum would helped me sort out this probs.
Sorry for my english and thanks for reading my post.
Read this :http://forum.xda-developers.com/showthread.php?t=308691 download splxploit-windows.zip (935.1 KB, 7619 views) put phone in bootloader run splxploit when bootloader change
After this download full rom here is link:http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
Then flash full rom bat do not disconnect usb cable in any step.
Before use any step disable active sync.
Usb are dead
Gsmhacks thanks for ure reply. I have tried that one, and lot read ing on wiki. But since i cant use the usb i cant use that splexploit whether on live linuxcd, or .Net version even win version. The usb port cant be opened . I think i broke the usb pin. From the beginning everytime i flashed my trin i never used ruu utility, i always do the sd card method and that is the best and easiest method and it works for me.
I just curious perhaps can anyone or is there any utility to unbrick trin via sd card. I knew a lot a people has bring their trinity life from dead by using htc stackflow splexploit. I hope that was work for me too! Too bad my usb are dead. Damn!
Here what you need bat only work if you have hard spl
If you install hard spl before brick trinity you can use SD CARD to flash trinity. YOu need to formate sd card to FAT32 with Card Reader donwload full rom here is link: http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
then extract and file RUU_Signed.nbh rename to TRINIMG.nbh and copy it to the root folder of your miniSD card.
Here is full instruction again also first format sd card to FAT32 !!!! VERY IMORTANT to format sd card to FAT32 or all other step will not work THEN:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (or you can also use winrar via wine).
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
and you will flash and unbrick trinity bat this only work if you install before this hard spl i mean cid unlock trinity. if not you must fix usb port.
That will work? I hope so
Ok then i'll try flashing using that rom. Oo, i have install hardspl btw and so far flashing using sdcard method no probs. But after i bricked my trin flashing doesnt smooth like be4. Always gave me error 0018003 update fail on the halfway, i guess because i have bad nand on trin and probably cuz cooked rom.
Can u give me another link, perhaps on xda ftp. rapids so slow 4 me. Btw i have download dopodasiawwe official rom on xda ftp *twice but still when i tried to run the package it gave me corrupt archive integrity fail w!f.
Thanks gsmhackerns, i downloading the package now!
Perhaps you can find a way to make a goldcard for Trinity?
See http://forum.xda-developers.com/showthread.php?t=437996
That's what i looking for! Thanks.
Humm, superb. Yay, great! Thank you stepw. Even its for elf with a little mod i hope this will work. Once again thank you.
Stepw, i have tried making the gold card, everything went ok. I have temp. cid *supercid* but the probs now is i can't download http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.execan someone uploaded to somewhere else. Rapidshare crap! perhaps on xda ftp.
thanks!
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
cmonex said:
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
Click to expand...
Click to collapse
Indeed. Youre right cmonex, it doesnt make any difference at all 4 my trin. After several tried using and making goldcard 4 trin, finally i made working goldcard4trin, but gosh it still stuck when i tried to update the os (update os fail) humm anyone.
Sorry for wasting your time with Goldcard, I have overlooked that you have a hard spl on your Trinity. In this case goldcard doesn't make a lot of difference.
And there's no trindiag.nb to the best of my knowledge that could be used instead of SSPL cmonex is suggesting to run from SD.
Back to the topic, sounds like you have some "bad" blocks in flash and OS can't be flashed. Bad blocks can be reset with "task 2a" command, see this thread for more details:
http://forum.xda-developers.com/showthread.php?t=330496
The question is how to run it without USB and I don't have an answer for you
Some people have previously mentioned they managed to flash smaller OS images when larger images failed, perhaps if you try flashing some minimal vanilla ROM, it will succeed?
Bad NAND, Yup!
Ya... as i mention before yup i do have bad nand block on my devices. Using manila rom with smaller img size the flash went 'OK'. But it doesn't boot at all infact just black screen with green led on.
Okay the only solution probably use mtty and do task 2a if i'm not mistaken. But like you said "The problem is the USB port". I think the port is ok cuz i already tested it connecting my usb to my trin without inserting the battery and the red led *magenta* is on. humm, weird!
But if something can make it working without involving any pc connection it would be a great achievement. hahah! well i supposed i have to put my trin on bunker before someone can make it happens
I asked SEA in my country and they recommend me to changed the machine it self and they charge me around US $160 ho...ho.. too "wideeeeee" for college boy like me
Same problem, i flashed the rom
RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship
and after that i tried to flash a new radio!
power+cam and the cell phone did not show usb, then i used sspl to rum the radio but it locked at 0%
after that it is stucked at bootloader screen
ipl 1.0
spl 3.20 .....
but no usb and no sd card !!
did i lost the cell phone?
there is no jtag ou something like that ?
so now... you still want this SSPL? i'm thinking of patching one up to automatically run task 2a maybe. or just restore stock spl for warranty service if that's what you have in mind. but you didn't really reply to that offer?
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Needed!
Cmonex, sorry for longtime haven't seeing this thread again. okay i really need your help btw if you willing to help me. The spl your talking about perhaps can sort out the probs (i hope) at least we tried. as for task2a cmd to clear the bad nand block is none usefull for me since usb conn. are definitely drop dead.
how about patch the SSPL to do task2a cmd to solve the bad NAND block first.
dinizbruno said:
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Click to expand...
Click to collapse
no usb, no sd, no chance sorry. jtag it or get it serviced or get another phone.
as for jtag, hermes jtag has been worked out by scholbert. trinity is probably the same, but you will have to find the pins. the rest of the process will be the same.
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
The O.S is more important to these operations than can be stressed - for a 99% safe flash Win XP is your best bet , I have had nothing but error 260,270 halfway flashed roms and usb faults running on vista and since I had my original bricking episode - NOTHING , I repeat NOTHING including genuine roms has flashed without a recovery or at least without doing something strange in the process - SPLXPLOIT has been a saviour here , without it I would've been lost.
Cant the O.P simply use another machine to test out the USB theory ?
ALIVE AGAINnnnnnnnnnnnn!!!!!!!!
My p3600 was stucked att bootloader, and wont give "usb" and do not read TINIMG.NBH (tried on elf with ELFIMG.nbh and the card was great)!
I did a golcard with the post on elf about it and the cell with the gold card inside was the same, no trinimg.nbh and no usb.............
BUT..............
with the goldcard inside, turned OFF, i placed it on the usb cable off the pc and the device booted to the bootloader screen, but this time he got "USB" , before flashing anything i removed the card , and putted switched off in the usb, booted with "serial" with card and pressing power and then placing usb still "serial" message!
I putted the card, did not switched on , placed on the usb and waited for it to boot for it self , and for my surprise "usb".
Flashed stock rom, and it booted nice!!!
Please try!
saved my day!
sidekraouf95 said:
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
Click to expand...
Click to collapse
I have to know how to repair my phone please... nobody can explain precisely how to put my phone on bootloader using my sd card directly from my computer under vista...???
(I'm not 100% sure this is the correct forum, but since it is very ROM related it didn't feel all wrong to put it in here...)
Hi guys. After som serious flashing of cooked ROMs I decided for some unknown reason that I should try to restore a stock ROM. Now, being very tired as I was, i completely forgott that its probably a good idea to flash a new Stock ROM on the unit BEFORE flashing it with a signed SPL....so I just flashed the Signed SPL to the device. That in it self seem to have gone ok, because when I start the unit it say "SPL-1.15.0000". Problem is though that it also says "Upgrade ROM error, please try again"
Now, what should I do? Have tried put both signed and unsigned SPLs on the storage card and started up via the volume down/pwr button thingy, but that does not seem to do anything. I have also tried to attach the unit to a USB port when in tricolor mode ("USB" shows up on the screen) and tried the CustomRUU program. It finds the device and starts to "upgrade" (grey screen on the device with 0%) but then it just doesnt seem to get any further...
As the device was working fine with a custom ROM before I started all this, I suspect that the main problem proably is that I now have a Standard SPL with a cooked ROM, and that they collide sort of. I, as well as the Blackstone, is now stuck and I am all out of ideas what to do? Have also tried Hard and Soft resets, but that doesnt seem to change anything.
Help!
try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps
You can try USPL on your HD and flash a custom or stock ROM with it.
PapaDocta said:
try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps
Click to expand...
Click to collapse
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).
improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success. Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
Click to expand...
Click to collapse
just do uspl it will work
improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).
Click to expand...
Click to collapse
bootloader mode is when you power off the device and hold the volume button down and press power till you get the tricolor screen...
so here is what you need to do .
1. remove the sd card
2. go into the tricolor mode connect your device to the pc and make sure it says (USB) at the bottom
3. run the stock shipped exe from you pc
if that didn't work then you should try the USPL version.. and there is a guide if you are using vista.. i just tried and worked fine.. here it is
http://forum.xda-developers.com/showpost.php?p=3331078&postcount=153
and the reason i'm asking you to remove the sd card because if you have a rom (blacimg.nbh) it won't let you do anything it will try to flash from the sd card and right now you don't want to do that.
and you shouldn't put any rom into the internal storage of the phone..
PapaDocta said:
and you shouldn't put any rom into the internal storage of the phone..
Click to expand...
Click to collapse
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?
nicelad_uk said:
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?
Click to expand...
Click to collapse
i don't think anything would happen... the file will get deleted when you flash as the rest of the files in the internal memory
Thank you everyone! The USPL thing solved it, when I did it from a XP machine! The once bricked Blackstone is not alive an kicking again!
About USPL, I saw the workaround for Vista, but downgrading a few components to make it work just doesn't seem like a safe way to do it. And I cant help but to think that it might have unwanted side affects, ie affecting system stability. But maybe I am wrong?
Going back to shipped ROM without bricking?
Hi,
After reading this thread I am now a bit worried and, as a newbie, would appreciate maybe a "simple" answer to my question.
I''ve been experimenting with various cooked ROMs after following the guide in the WIKI for installing HardSPL and then putting the ROM file (BLACKIMG.nbh) on my SD card and installing it using the power on + volume down button method.
However, I now want to revert back to the original "shipped" ROM, which I have downloaded from the list of shipped ROMs via the WIKI (I downloaded the one which closely matched what was originally on my HD - as I didn't know how to backup the actual ROM on my HD at the time).
So, my question:
How should I put the downloaded original/shipped ROM:
RUU_BlackStone_HTC_WWE_1.14.405.3_Radio_52.49a.25.26_1.09.25.14_Ship.exe
into my HD without bricking it?! Do I just run it on my PC with ActiveSync enabled or do I need to do something to remove the HardSPL or something first?
Sorry if this has been answered previously but I get confused when a thread just makes loads of references to SPLthis and SPLthat etc.!
if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..
PapaDocta said:
if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..
Click to expand...
Click to collapse
Brilliant! Thanks for the simple answer Worked no problem!