Related
Hi I'm hoping someone can help me with what appears to be a unique problem based on all the searches I've done.
I've been able to install ROM updates with no problem for a long time with my Cingular 8125, however recently I'm getting stuck on the bootloader screen. It's a little strange, but here's what happens:
1) From Windows, if I try to flash ROM using USB it gets as far as rebooting the device and bringing up the bootloader multicolor screen, and it says USB on the bottom as it should. From there I can't get to the device at all and the installer fails with a device connection error. All I can do then is reset and get back into the OS like normal.
2) With the SD card method, I get to the bootloader screen but it never loads anything from there, and again I have to reset and just get back into the OS.
I'm running IPL/SPL 2.26, using Molski's latest ROM, but now can't install any other ROM because of this.
Any ideas?
Thanks in advance
groggrog said:
Hi I'm hoping someone can help me with what appears to be a unique problem based on all the searches I've done.
I've been able to install ROM updates with no problem for a long time with my Cingular 8125, however recently I'm getting stuck on the bootloader screen. It's a little strange, but here's what happens:
1) From Windows, if I try to flash ROM using USB it gets as far as rebooting the device and bringing up the bootloader multicolor screen, and it says USB on the bottom as it should. From there I can't get to the device at all and the installer fails with a device connection error. All I can do then is reset and get back into the OS like normal.
2) With the SD card method, I get to the bootloader screen but it never loads anything from there, and again I have to reset and just get back into the OS.
I'm running IPL/SPL 2.26, using Molski's latest ROM, but now can't install any other ROM because of this.
Any ideas?
Thanks in advance
Click to expand...
Click to collapse
Just for everyone's information: I was able to resolve this by re-running lokiwiz and doing a SuperCID unlock...
Greg.
How did you make to lokiwiz recognize qtek?
My qtek shows:
First (and only) screen shows 4 color (red, green, blue, white), so according to posts on HTC-forum that must be boot loader.
On right upper corner of screen stands RUU
Line bellow, in the upper left corner shows IPL 2.26
Approximately 3 lines bellow still in the left upper corner of the screen shows SPL 2.26
When connect USB cable to qtek on the left down corner shows USB
I can acces to qtek via Multi-port/USB TTY ver. 1.11a, but when I start lokiwiz, even after long period of time nothing happens?
Please give us a precise procedure, nothing else didnt help
Hi,
I just tried to flash a wm6 rom on my mda vario but at 99% my USB connection stopped so now I only see a red-green-blue screen when I put my mda on...
Does anyone know how to solve this problem?
I'm really desperate right now:S
Read this:
http://forum.xda-developers.com/showthread.php?t=298613
mfrazzz said:
Read this:
http://forum.xda-developers.com/showthread.php?t=298613
Click to expand...
Click to collapse
I tried what he says but it would'nt work....
The flash program cannot find my MDA so i couldn't flash the rom onto it
Do you think my mda is dead?
dantheman2004 said:
I tried what he says but it would'nt work....
The flash program cannot find my MDA so i couldn't flash the rom onto it
Do you think my mda is dead?
Click to expand...
Click to collapse
Ok, so you are on the bootloader... Whats the IPL / SPL showing (exactly what both numbers are). When you plug in the USB cord, do you see USB above the left softkey (if you do, then you can flash). Is your phone a G3 or G4?
What is the exact error you get when you try to flash to your phone?
Have you tried flashing on a different PC? Have you rebooted your PC? Pull out the SD card on your phone before turning it on and flashing it.
In the WIki there is a link to how to flash from your SD card, if all else fails you may have to try that (but that would be a last resort IMO. Also remember that in the current state, your phone will not charge, so you may have to look at getting your battery charged.
mfrazzz said:
Ok, so you are on the bootloader... Whats the IPL / SPL showing (exactly what both numbers are). When you plug in the USB cord, do you see USB above the left softkey (if you do, then you can flash). Is your phone a G3 or G4?
What is the exact error you get when you try to flash to your phone?
Have you tried flashing on a different PC? Have you rebooted your PC? Pull out the SD card on your phone before turning it on and flashing it.
In the WIki there is a link to how to flash from your SD card, if all else fails you may have to try that (but that would be a last resort IMO. Also remember that in the current state, your phone will not charge, so you may have to look at getting your battery charged.
Click to expand...
Click to collapse
The ipl is 1.01 and the SPL is 2.21
I don't get an error when I try to flash the phone, it just won't connect with the pc
dantheman2004 said:
The ipl is 1.01 and the SPL is 2.21
I don't get an error when I try to flash the phone, it just won't connect with the pc
Click to expand...
Click to collapse
1) Your IPL is 1.01. DO NOT flash WM6 on this phone. You have to be running IPL / SPL of 2.xx for WM6 to work or you will have all sorts of problems / weird issues.
2) What do you mean "it just won't connect with the pc"? When you are at the bootloader Activesync will not connect, but if you see USB above the left softkey on your phone then they ARE connected. You just run the RUU and it will flash (trust me).
3) Based on your IPL / SPL you have 3 choices...
a) Try flashing the Button ROM and get that working. Then do the CID Unlock procedure and follow every single step and verify everything is exaclty as that thread says it should be:
http://forum.xda-developers.com/showthread.php?t=285435
b) Flash an official ROM. Once you are done, you may or may not have to do the CID Unlock (hard to say with your current IPL / SPL situation). Personally I'd do the CID unlock again to be safe.
c) Flash the Wizard Love ROM (if a and b don't work). Once you do that, then do a to do the CID Unlock.
If this still doesn't help, then you need to be very precise (no more short answers) with exactly what you are doing and what happens when you do it. Its hard to debug this situation when you don't tell us everything. Also you dd not answer any of my previous questions to you. Please do that.
I am having the same problem with a Cingular 8125. I used buttons 1.05 rom to downgrade from the original 2.25 so that I could use the Lokiwiz 0.2b. When that was complete I had IPL 1.01 and SPL 2.25 (similar to dantheman). After that I ran faria's WM6 RUU. All seemed to install well, but after reboot I got error "\Windows\Autoconfig.exe not found". Searching a forum on HTCWizardWeb someone had the same problem and the advise was that he should have used ShellTool to install the WM6 rom, so I did that. All seemed to install well, but after hard reset (as instructed) the device stays on the IPL/SPL screen with the beer mug. No USB message shows above the left softkey when USB is connected. The only time the PC seems to recognize a USB device connected is when I have uninstalled ActiveSync, rebooted, re-installed activesync and plug the wizard in not powered up. Then the taskbar shows USB device found, then your device is ready. I try the 1.05 rom after is says device is ready and it does not detect the wizard (Error 260:UpdateError, The update util cannot connect...) Noted that when I plug the wizard in powered on to the IPL/SPL screen the USB device connected message does not appear. I can only get to that screen and connectivity seems limited.
At this point when i do a hard reset I get "format failed" error and back to IPL/SPL screen.
mmain said:
I am having the same problem with a Cingular 8125. I used buttons 1.05 rom to downgrade from the original 2.25 so that I could use the Lokiwiz 0.2b. When that was complete I had IPL 1.01 and SPL 2.25 (similar to dantheman). After that I ran faria's WM6 RUU. All seemed to install well, but after reboot I got error "\Windows\Autoconfig.exe not found". Searching a forum on HTCWizardWeb someone had the same problem and the advise was that he should have used ShellTool to install the WM6 rom, so I did that. All seemed to install well, but after hard reset (as instructed) the device stays on the IPL/SPL screen with the beer mug. No USB message shows above the left softkey when USB is connected. The only time the PC seems to recognize a USB device connected is when I have uninstalled ActiveSync, rebooted, re-installed activesync and plug the wizard in not powered up. Then the taskbar shows USB device found, then your device is ready. I try the 1.05 rom after is says device is ready and it does not detect the wizard (Error 260:UpdateError, The update util cannot connect...) Noted that when I plug the wizard in powered on to the IPL/SPL screen the USB device connected message does not appear. I can only get to that screen and connectivity seems limited.
At this point when i do a hard reset I get "format failed" error and back to IPL/SPL screen.
Click to expand...
Click to collapse
Your phone isn't unlocked. How are you hard resetting? And you are sure you have a G3?
--M
You didn't follow all the directions for downgrading. Go back and reread Dr P's sticky, but after you do lokiwiz, you have to flash the button rom again so that both IPL/SPL are 1.xx. Then you HAVE to upgrade to an official 2.xx rom to get IPL/SPL to both be 2.xx.
Only after that is complete can you flash WM6 or other custom roms.
Thanks for your help...
You guys are right, I didn't follow all the directions correctly (or at least wasn't reading the correct set of directions, not sure). But for those that made the same mistake that I did here is how I got it going again.
It actually cost me $50, but it was worth it. I found a post about a fix using an SD card, but the phone had to be CID-unlocked (which apparently was the reason the ROM update I tried failed). And another post told me the only way to unlock my phone from the bootloader screen was to use the www.imei-check.co.uk website to unlock it. It cost $40. After i did the CID unlock via that website go to the forum post -
http://forum.xda-developers.com/showthread.php?t=276963&highlight=splash+screen+freezing
I had to buy a 512mb miniSD at wal-mart last minute and paid $20. Anyway that's what fixed it for me, even though it cost me some money.
Greetings.
I have spent the past couple days searching for a solution to unlock an MDA. I have got all of the different versions of lokiwiz, wizardunlock, lokiwizMsl, etc. and the mda refuses to be unlocked. I believe I am following the directions step for step, but even the forums where people have the same problems as I (internal read/write error, can't find specified path, etc.), none of the solutions are working for this device. From my searching I believe it is a g3 MDA. The stats for the device are as follows:
IPL 2.26
SPL 2.26
GSM 02.25.11
OS 2.26.10.2
I have tried downgrading the firmware to no avail (the ftp site doesnt have the file), and the phone doesn't want to be DOWNgraded anyway. If ANYONE out there is cyberspace can assist, my gratitude will be pouring forth from their screen!
[email protected]
So have you followed this thread? It has valid links to get the Button ROM so you can do the downgrade and points you to the threads that will help you do this unlock:
http://forum.xda-developers.com/showthread.php?t=298613
In a nutshell, downgrade to the button rom (just execute the file and follow the directions). Your IPL will be 1.xx at this point and then you can use lokiwiz .2b to do the CID unlock. all of this is outlined in the excellent guide by Dr. P (which the above link will take you to). Then get your SPL down to 1.xx, then upgrade back up to 2.xx. Then you can start flashing custom roms.
If you still have issues, let us know exactly what you are doing and exactly what errors you see (or what your phone does or doesn't do).
Greetings mfrazzz.
I have indeed downloaded and attempted the button ROM. The installer started and then after about two minutes told me that the phone wouldn't let me Downgrade the ROM. I am currently downloading (70% done) the button ROM again and will see if it has the same problem. If so, I will of course seek the help of the experts here. Thanks for the quick reply!
gtw said:
I have indeed downloaded and attempted the button ROM. The installer started and then after about two minutes told me that the phone wouldn't let me Downgrade the ROM.
Click to expand...
Click to collapse
Let us know the exact error you get (I assume the error is on the PC side) and then what the behavior of the phone is after you do this. Also, at what point does this error happen (has it actually started loading the rom or is it before it gets to that point and where its just checking your phone?)
Another option would be to try putting on the Wizard Love rom and then downgrading to button. Shot in the dark but worth a try.
Also remove your SD card when you try to downgrade. Try from a different PC if you can, or reboot your current pc before attempting this again.
Good luck!
Greetings again.
After downloading and executing the button ROM updater, it went to the status bar screen and stayed there for about a minute before displaying the following error message:
Error [296] : UPGRADE ONLY
This is (I believe) the same error I got previously. I was using RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship (which is the file that I downloaded from http://forum.xda-developers.com/showthread.php?t=298613 under the link button ROM (step g3.3).
ALSO... the phone is stuck in the multicolored ROM screen. (the red green and blue) On the screen (from top to bottom
IPL 2.26 RUU
SPL 2.26
USB
gtw said:
This is (I believe) the same error I got previously. I was using RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship (which is the file that I downloaded from http://forum.xda-developers.com/showthread.php?t=298613 under the link button ROM (step g3.3).
Click to expand...
Click to collapse
Nope, thats the Cingular 2.25 ROM. Thats why you are getting the error (since you aren't CID Unlocked it won't let you load that).
The ROM you are supposed to be loading is this one:
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
Thats the Button ROM (and the one I show being in that link on that page). Please download that, and run it. You should make more progress
Since you are on the bootloader screen (Rainbow screen you described) just run the button rom when you get it downloaded (active sync will not connect, but since you see USB above the left soft key you have the connection to do this).
I see....it would make a difference if I got the right program! Rapidshare says I have ten minutes before I can download another file, so after I download http://rapidshare.com/files/18212239...WWE.exe.h tml, I will try it and post the results here! Thank you so much for your help, mfrazzz!
Greetings.
After downloading and installing (onto the phone) http://rapidshare.com/files/18212239...WWE.exe.h tml, the stats for the phone are
ROM: 2.26.10.2 WWE
Radio Version: 02.25.11
Protocol: 4.1.13.12
ExtRom: 2.26.10.105
After executing lokiwiz, lokiwizMSL, wizardunlock, and a few different versions of each (after I put the enableRapi onto the phone), the phone still won't unlock. It either gives me a "Cannot find the specified path" error, or the "Internal read/write error".
Im not sure that the file I downloaded was a 'down'grade, so if anyone sees a solution, please post!
Thank you
Did the flash of the Button ROM work? Your IPL should have changed to 1.xx after doing that flash (and your splash screen would be a photo with a mug of beer in the foreground). Since your IPL and SPL still show 2.26, it appears the flashing of the button rom didn't happen.
Not sure what else to tell you. It should be as simple as running the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe file, and letting it flash to your phone to do the initial downgrade. But you have to be a 1.xx for IPL before the lokiwiz .2b will be able to work (so there is no point in doing anything else until the steps before that complete. Again, follow to the letter (including checking the results) the thread by Dr. P on CID Unlocking. You should never try to do steps before the previous step is complete).
mfrazzz said:
It should be as simple as running the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe file, and letting it flash to your phone to do the initial downgrade.
Click to expand...
Click to collapse
I thought it would be that easy too. I clicked on the file, it went through the flash, and those are the stats that showed up. I am currently trying the flash again. One difference I noticed this time is that the version it says is going to be installed is 1.xx this time, last time it said 2.XX. It looks like its going ok, though. Ill post again once it is done.
Greetings.
THANKS FOR YOUR HELP MFRAZZZ! Not only did your prompt responses brighten my otherwise gloomy, MDA filled day! Your patience with my noobitude on this device (its not mine) has been a blessing beyond anything I could have hoped for. The device is now UNLOCKED!!! After the last flash, the beer mug showed up and all was well. Lokiwiz worked like a charm and your help, as I said, was much needed! THANK YOU!
gtw said:
Greetings.
THANKS FOR YOUR HELP MFRAZZZ! Not only did your prompt responses brighten my otherwise gloomy, MDA filled day! Your patience with my noobitude on this device (its not mine) has been a blessing beyond anything I could have hoped for. The device is now UNLOCKED!!! After the last flash, the beer mug showed up and all was well. Lokiwiz worked like a charm and your help, as I said, was much needed! THANK YOU!
Click to expand...
Click to collapse
Very cool. Just make sure you get the SPL down to 1.xx before you move back up to a 2.xx Official rom and you will be golden.
Congrats, and glad I could help
mfrazzz you are amazing
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Adding additional info
My phone is a G3, CID and SIM are unlocked, desktop is using Windows XP, SP2 and ActiveSync is Ver. 4.5.0
phone isnt bricked, your getting into bootloader fine. you need to turn it on, get it into bootloader i mean. if needbe press camera and soft reset (power button) then plug it in USB. You then need to flash your phone with the operator ROM, or the ROM you want to flash it with. Your phone is by far bricked, G3 ones are really difficult to ruin. I learnt that first hand
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
jphuffs said:
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Click to expand...
Click to collapse
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
akashastrega said:
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
Click to expand...
Click to collapse
hi
i have read ur situation at thread u have mentioned here,well i can assure u it's not bricked,cuz as sometimes it's able to go to bootloader mode.
The only problem to me seems the usb connectivety problem.
does it charge ?,if not then clearly it' a usb connectivity,if u can manage to get another usb cable and check out,hope it wud clear this doubt
zabardast_1 said:
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
Click to expand...
Click to collapse
I just had this happen to me as well, I got stuck a 29%
Now when I get to bootloader it shows the IPL 2.26 and SPL 2.26 and also a RUU in the top right hand corner. Plug in USB and I get USB at the bottom left but then when I try to launch the RUU with the rom I want to flash I Invalid update tool, download new tool... It wont "Verify information on the device"
**EDIT
Nevermind, I just got Titanium to take... I may be ok... I think the RUU in the vanilla download I got is messed up or something...
Currently ripping through the rom update now. Damn I just got this phone yesterday I was gonna be pissed if I killed it.
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
ok when u swith on the phone what happens ?
does it go to bootloader mood ? or u force it to go bootloader by keeping camera button pressed and doing soft reset ?
well,after geting to bootloader mode,don't reset again just establish usb connectivity and when it show usb in the lower part of the bootloader screen launch ruu and start the flash.if it still stops with an error,post that error,then it means u had a bad flash or no flash at all.are you pretty sure you got it CID unlocked ?
tell you what you do,go to this link download WST tool and apply it,than post the data info it gives here,this will give the present status of your phone,ok
http://forum.xda-developers.com/showthread.php?t=329170
read this sticky:http://forum.xda-developers.com/showthread.php?t=298613
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
download the wizar-love rom
flash it using the ruu provided..
ftp://xda:[email protected]_Novii+CF2.rar
it should work.....
read this sticky
http://forum.xda-developers.com/showthread.php?t=298613
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Crashed during flash
It has been suggested that I download Wizard Service Tool. OK, I did that. The Wizard Service Tool says to connect to ActiveSync. Can't do that. Phone is locked in Bootloader. It boots up into Bootloader. Any action requiring ActiveSync won't work as long as the phone is locked in Bootloader. Any suggestions as to procedures at this point. Remember, that trying to flash the ROM at this point, I get a message 300 that says I need to get a newer update utility.
Crashed during update
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
jphuffs said:
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
Click to expand...
Click to collapse
go to the G4 section and look for the HardSPL thread. Once there get the MUNRUU file from first post and use it with the ROM you wish to flash as it might do the trick of the ERROR 300
crashed during flash
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
(mestrini;1565518]this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796)
My phone is a G3. These links are pretty adamant about being for G4 only
jphuffs said:
My phone is a G3. These links are pretty adamant about being for G4 only
Click to expand...
Click to collapse
I'm talking about the, so called, 'MUN RUU' which are the files used to upload the nk.nbf. You just have to replace those for the ones you're using now; NOT THE nk.nbf, just the others...
zabardast_1 said:
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
Click to expand...
Click to collapse
What is "Official Rom from carrier official site"?
The SIM card was removed.
Hope this helps
jphuffs said:
What is "Official Rom from carrier official site"?
The SIM card was removed.
Click to expand...
Click to collapse
For instance, if you are (like me) with TmobileUS, go to the Tmo site and go to the page that gives you the download to rom 2.26. I have that rom, if you are with Tmo, but won't be able to upload it until later...
http://tmobile.infospace.com/tmweb/...wnloadCenter/DeviceDownloads.aspx?deviceID=24
THAT^^^ is for TMOUSA...it is the official Tmo rom. If you are with cingular/att, you need to access their website and download their official rom, etc.
I just got a att tilt.. I have tryed to unlock it using the kaiser sim unlocker. At first it would just go to the load screen and it would say 0%... a white screen. so i looked for a posting with that. And i found this ------HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)-----
on that i got all the way up to 95% and then I got a err message.. now all it will do is go to the load screen (white) and show 0% and then I follow the instructions.. and when I go to restart the phone it show the red,green,blue,white screen.. top left show
kais1*0
spl-1.56.0000
cpld-8
top right show
ruunbh
what happen please help.. this is the first time this ever do this to me.. i have ren unlocked programs from hear befor with np..
bikepilot said:
I just got a att tilt.. I have tryed to unlock it using the kaiser sim unlocker. At first it would just go to the load screen and it would say 0%... a white screen. so i looked for a posting with that. And i found this ------HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)-----
on that i got all the way up to 95% and then I got a err message.. now all it will do is go to the load screen (white) and show 0% and then I follow the instructions.. and when I go to restart the phone it show the red,green,blue,white screen.. top left show
kais1*0
spl-1.56.0000
cpld-8
top right show
ruunbh
what happen please help.. this is the first time this ever do this to me.. i have ren unlocked programs from hear befor with np..
Click to expand...
Click to collapse
It shows you are using the 1.56 SPL, which is the Stock AT&T SPL.
Download the official AT&T 6.0 Shipped Rom here:
http://rapidshare.com/files/55298724/RUU_Kaiser_CINGULAR_WWE_.exe
Take out your SD card and flash this ROM. After you have a successful flash and your phone boots up normally, post back and we'll go from there.
bengalih said:
It shows you are using the 1.56 SPL, which is the Stock AT&T SPL.
Download the official AT&T 6.0 Shipped Rom here:
http://rapidshare.com/files/55298724/RUU_Kaiser_CINGULAR_WWE_.exe
Take out your SD card and flash this ROM. After you have a successful flash and your phone boots up normally, post back and we'll go from there.
Click to expand...
Click to collapse
Ok I tried that it go to 1% and then it go to say
ERROR[294] : INVALID VENDER ID
this update untility cannot be used for you pda phone pleas check you Update utility
bikepilot said:
Ok I tried that it go to 1% and then it go to say
ERROR[294] : INVALID VENDER ID
this update untility cannot be used for you pda phone pleas check you Update utility
Click to expand...
Click to collapse
You could try this
More specifically, might want to read this whole thread and search it for RUUNBH.
MTTY should be able to help as long as you use the proper commands.
bengalih said:
You could try this
More specifically, might want to read this whole thread and search it for RUUNBH.
MTTY should be able to help as long as you use the proper commands.
Click to expand...
Click to collapse
Ok got it back to all origanal...now every time i take the battery it go back to the colar screen ( now what