Hi All
Thanks for creating such a great site - its become a total lifeline for me with my XDA.
I need some help on setting up my sat nav. I have Tom Tom 5 put on a 1gig SD card, and I'm using a fortuna GPS U2 receiver which has a USB connector one end, a connector to the PDA in the middle and a PS2 connector to the GPS antenna on the other end.
Been trying to configure it in Tom Tom, I know I need to set the baud rate to 4800 as per fortuna's website, but does anyone know what I should tell the system the GPS is connected to? I have a number of options:
Com9
Serial Cable on Com 1
Serial on USB
Infared Port
Serial cable on Com 2.
I've sat out in the car an played around but can't get it to pick up a signal and I'm ondering whether its me setting it up wrong that isn't helping.
Please...can anyone help me?
Simon
try this
on your phone go into settings then connections then beam and untick beam then in tomtom go into change preferences then show gps status then into configure select other gps receiver then select com1 try this if you search wallaby forum there is lots of post on this
jay
try this
on your phone go into settings then connections then beam and untick beam then in tomtom go into change preferences then show gps status then into configure select other gps receiver then select com1 try this if you search wallaby forum there is lots of post on this some of these cables don't work i got one off ebay said it would work but never had to change the wiring look at thishttp://wiki.xda-developers.com/index.php?pagename=Connectors
jay
Thanks Jay - after lots of swearing and soldering I have now reassigned the pins and so far all seems well. The only thing I'm not getting at the moment is audio out of the speaker - however I do get audio when the headset is connected. Does anyone have any ideas?
audio
turn the audio on in tomtom its in the settings
Related
Sorry to bother this forum whith even more questions about my car kit and TomTom GPS
I am trying to conect my TomTom GPS Mouse to my O2 CarKit.
I have found the pin configuration from another post on this site for the O2 Carkit connector.
RTS - Purple
DCD - Red
DTR - Blue
CTS - Yellow
RXD - Green
TXD - Orange
GND - Black
+5.5 V - Brown
(I hope this is correct)
But what the pin configuration for the TomTom GPS Receivers RJ11 connector is - I have no idea.
Please help anybody who knows which pins connect with which.
Thanks...
Yeah this one took me a while too....
Ok this is how to do it:
This is how to install a Leadtek GPS-mouse on the original O2 Carkit.
(The mouse shipped with Tom Tom Navigator is a Leadtek)
First of all you only need the cable with the RJ11 plug and the gps mouse on it. The 12V adapterplug you don't need anymore.
Preparation:
On the Carkit is a weird looking black connector for the gps.
Cut that off...
Now connect a connection block(I don't know the english word for it, but i mean the white blocks with screws in them so you can connect wires with other wires) to the following wires:
Brown
Black
Orange
Green
Now you can start:
Now you can choose to connect the mouse directly of you can make a removable connection. When I installed my carkit I used a fixed connection, but when I helped a friend out installing his carkit I used a standard phone connection box. You need a box where you can plug in a RJ11 connector. This is a better option because jou can easely unplug the gps mouse en use it again with the 12V adapter. This may come in handy if you want to be able to navigate in an other car too (Rental car on vacation).
I will explain how to make a fixed connection, so mounting a box in between will be fairly easy.
1) Cut off the RJ11 plug from the mouse
2) Strip the wires
*********
Note: The color codes of Leadtek mouse change all the time!
*********
In my case it where the following colors:
[Red](VCC +5)
[Wit] (RX)
[Black] (TX)
[No isolation] (Aarde)
3) Connect [Red] with (Brown)
4) Connect [White] met (Green)
5) Connect [Black] met (Orange)
6) Connect [No isolation] met (Black)
This should work!
PS
It may be wise to mount a switch between the radio-mute cable, because it mutes when you start TomTom.
You might want to listen to music when driving and navigating long distances.
do you know the pin numbers on the rj11 connector incase my wires are different colours...
No but you can see the wire witch no isolation as Pin 4
You're welcom, by the way....
Thanks for your help - my sat nav is now working through the xda car kit.
I was a bit nervous when i pluged it in for the first time - but nothing blew up and it is now all working - i would recomend this setup to anybody.
It took me a few minutes to juggle all the volume settings around untill i found a combination that had phone calls and sat nav voice prompts all at the same level but once that was done everything is fine.
maxlw said:
No but you can see the wire witch no isolation as Pin 4
Click to expand...
Click to collapse
Can you help me please????
when i connect the adaptercable from my gps system the xda stells me that the com1 port can't be found.
The tomtom software works, but the gps mouse is not recognised.
What can i do??
Thxs in advance,
rene from holland
Im sorry - i cant help - when i connected it all up it just worked first time - i had no error messages so have no experience in sorting them out...
check here http://www.pdashop.nl/support/1732/79 for a pin diagram for the rj11 connector for the leadtek gps mouse and check your wiring is the only thing i can suggest.
The connections should be as follows...
A1 to Black
A2 to Orange
A3 to Green
A4 to Brown
Hope this helps...
roycruse said:
Im sorry - i cant help - when i connected it all up it just worked first time - i had no error messages so have no experience in sorting them out...
check here http://www.pdashop.nl/support/1732/79 for a pin diagram for the rj11 connector for the leadtek gps mouse and check your wiring is the only thing i can suggest.
Click to expand...
Click to collapse
I just heard from another member. The solution is simple: if i turn out the irda port it should be ok.
I'm gonna trye first thing tomorrow.
thxs,
rene
I am having a problem with the xda not charging properly in ther O2 cradle whilst the GPS mouse is connected - its almost as if the GPS mouse is using most of the available current.
Im thinking of adding a resistor in series with the +Ve feed to the GPS mouse to limit the current it can take hoping this will leave more for charging the xda.
Does anybody else have any experience with this... what value resistor should I use...
Im thinking of adding a resistor in series with the +Ve feed to the GPS mouse to limit the current it can take hoping this will leave more for charging the xda.
Click to expand...
Click to collapse
Don't do that!!!!
It should work fine without...
Can you help me please????
when i connect the adaptercable from my gps system the xda stells me that the com1 port can't be found.
The tomtom software works, but the gps mouse is not recognised.
What can i do??
Click to expand...
Click to collapse
IF COM1 can't be found you have installed it correctly!
Hook everything up like before and then disable beam connection in [settings],[connections],[Beam]
This is a known problem with navigating on a pda!
After that you will see that it works.
Just don't don't add anything yourself you'll probably mess up your hardware!!!
Here are the instructions in Dutch....
http://forum.pocketpc-club.nl/showthread.php?s=&threadid=12421&goto=nextoldest
Hi,
Just wondering if anyone has successfully hooked up a Garmin E-Trex to an XDA. It should be possible using the serial connector from both (null-modem!?!). If so what software was being used on the XDA.
Cheers
Jeff
Garmin eTrex - XDA
The eTrex and XDA make a great combination even with Pocket Streets: the eTrex gives you the vector to your destination and the XDA shows you where you are on the map at zilch cost. The draw back is that you can find your target destination on PStreets but there doesn't seem to be a way of extracting the coordinates to feed into your eTrex.
So I got the TomTom Citymap of London to try that out and after a poor user experience when the supplied gps driver locked the XDA up and I had to download another, plus no explanations of various 2.06 driver features plus finding that parts of the M25 London orbital were chopped off, I have the best of both worlds. It only cost me 10UKP.
Oh yes, connections. You can buy a TomTom power/gps cable for the XDA that is meant to take the TomTom gps mouse via a 4 connector phone type socket. So all you have to do is come up with a 4 connector phone type plug leading off to you eTrex. If you have the eTrex car cable for power and RS232, which you might want to use with a laptop, you will not want to cut this. So get a cheap RS232 cable and chop the appropriate end off for your phone type connection. Marry everything up, ignore the wife's complaints about wires and delayed departures while you fiddle with the eTrex and XDA, and you are off.
The TomTom cable phone socket housing can be taken apart briefly to check which are the Common, TX and Rx wires, and the tiny circuit board even tells you which is which. If you want I can give you the pin outs but at the risk of misinterpretation.
Etrex GPS
Managed to get it to work with Navigator and am well impressed.
Got a cable from http://pc-mobile.net/gps.htm. However had a few problems to start off with. The XDA ground to a halt (I have updated the ROM to the latest O2 release and apprently TomTom 1.4 has a problem with later version). Updated TomTom to 1.51 and still no joy. Change the interface from Garmin to IMEA 4800 baud on both GPS and TomTom and had a great weekend driving up and down the motorway and country roads in Derbyshire.
Jeff
Jeff,
Cool, isn't it! Perhaps you can enlighten me about Navigator. Not knowing much about TomTom I rather expected voice prompts on the citymap thingy I downloaded. Question: what do you have to do to get the voice prompts invoked (spend more money probably) and can you hear them from the XDA? :?:
Ken
Navigator Talking
I have Navigator 1.51 installed (downloaded from Tom Tom site) only you need at least a previous version as otherwise there are no maps.
When you do a route plan (rather than just have it in map mode), it does the "300 yards turn right......turn right.....find the next convenient place and turn round"
Not sure what happens with previous versions as I had 1.4ish on before and that interfered with Windows as I had upgraded PPC2002 to a newer version and it odesn't like that too well.
Cheers
Jeff
Hi guys, do you know if the connector for the Garmin Geko 201 is the same as the Etrex? I was looking at buying the Geko and the cable from the site listed above but they don't say specifically for the Geko. I put an email question in to the cable guys but you never know how long it will take to get an answer. It's definitely a flat connector and not a round pin type. Thanks - Jim
Hi,
I've bought a Fortuna U2 GPS receiver with an O2 XDA lead.
I've downloaded some software (GPSeasyCE), but when I try and connect to the GPS unit, I get "unable to open COM1".
Any suggestoins please?
I have tuned my keyboard driver to IR & serial, and I think I'm using the correct com port settings (4800bps, NMEA 0183).
I'd really like to just check that the hardware is working.
Can I download some free demo software that will do that?
What's best?
Thanks in advance, for any help anyone can offer,
Muddy
You have to turn off the IR port.
Muddy said:
Hi,
I've bought a Fortuna U2 GPS receiver with an O2 XDA lead.
I've downloaded some software (GPSeasyCE), but when I try and connect to the GPS unit, I get "unable to open COM1".
Any suggestoins please?
I have tuned my keyboard driver to IR & serial, and I think I'm using the correct com port settings (4800bps, NMEA 0183).
I'd really like to just check that the hardware is working.
Can I download some free demo software that will do that?
What's best?
Thanks in advance, for any help anyone can offer,
Muddy
Click to expand...
Click to collapse
disable your infra red port under setting, connections/beam, it will then work. A point about cables to work with gps, if you get a serial xda cable, and you also have a pc serial cable that links to your gps, all you need to do is get a 9 pin male to 9 pin male null modem adaptor, or make one, you need to join pin 2 on one to pin 3 on the other, pin 3 to pin 2 and pin 5 to pin 5, plug your xda lead one end, gps lead the other, and away you go.
I want to connect my Garmin Geko GPS to my PocketPC Phone Edition. It seems that regardless of what I do there's no receiving any data. It's only a three wire interface, so how hard can it be? The Geko puts out a NMEA format at 4800 baud, that's what the Pocket Streets application wants.
Q1: The Pocket Streets GPS Configuration screen shows that I have available COM2, COM3, COM8 and COM9. I thought I saw a COM1 in there before, but right now this is the list I see. Which COM port is wired to the connector?
Q2: I've heard that I may need to disable IR, a keyboard driver, or ??? to get this to accept input. Help out a newbie and tell me exactly how to turn off these features (it's not obvious to me).
Q3: I've loaded ZTerm on the PocketPC Phone Edition and used a serial cable to type back and forth with Hyperterminal on my XP system. This even down to 4800 baud. So I know it's possible to exchange data via serial port. Since it's only a three wire interface from the GPS, I've connected the Tx,Rx, and Gnd to the phone, but no data to the application or to ZTerm. I've tried tying the CTS, RTS and DSR lines together on the phone and made sure there was no handshaking, but still no data to ZTerm (or Pocket Streets). Wuzzup with this?
Thanks in advance! Bewildered with some cool toys :?
Ok I had a similar problem with TomTom.
Ok to disable IR go to Start/Settings the do to the connections.
Select Beam there should be a tick box labelled Receive all incoming beams.
Then go to pocket streets start it up and you should be able to select com1
Hope this helps, Just for information if the received all incoming beams is selected then it acts as your comm1, until this is de-selected you cant talk use the seial port on your bottom connecter.
Hi Chaps
Great web site !! I wonder if any body can help.I have Tom Tom Nav 2 and have just picked up a GPS receiver from ebay with a dual power/data cable. I pluged in both XDA and res and it seems to power up the receiver OK. I started Nav application tried to set up receiver with no luck...I have tried most settings .ie Serial on Com 1 this comes back with no Com 1, USB on serial etc..it still cannot see the receiver.
The receiver came with no instuctions..it could ge a Mitec (Blue small mouse like)
Could anybody Help
Thanks David
Assuming the receiver has the correct XDA cable and you have the GPS connected to a 12v power source, untick 'Receive all incoming beams' in Start | Settings - Connections/Beam.
You should then be able to configure COM1 in TTNav. Use 'NMEA 0183v2 4800' as the Port Speed.
Once you have unchecked the recive beams box you will find that choosing tomtom gps on com 1 will work for most gps mouse that run 4800 nmea.
Thank you to both for the help. The sat nav is working GREAT!!
Thank you again
David
thanks guys, i had the same problem and now satnav works perfectly!!
I have recently "upgraded" from xdaII to xdaIIs and I'm having a few problems. I have upgraded the BT stack to 3500 but I still can seem to connect to my tomtom gps. Device sees it but tomtom 3 cant. I'm completely confused by the connection wizard- none of the profiles seems to fit gps. I also dont seem to be able to send or receive files from my old xdaII. What am I doing wrong?
I'm also a little confused about roms. Do I need to upgrade my rom? Is there a simple way avoiding anything too technical (I've read about "country codes" and other wierd stuff). My current config is:
ROM: 1.12.62
Radio: 1.02.00
Protocol: 1337.32
ExtROM: 1.12.178
Could someone please help! I only have a few days to decide if I want to keep it or stick with my xdaII...
Gps's use the serial profile to transmit the data over - its like a virtual serial connection - so you need to tell tomtom to look on a com port AFAIK,.
For eample in my Tomtom list of connections there is one called 'BT on Com6, ' which is the bluetooth comport on my unit.
But there are also listed more com ports...
Com5
Com4
Bluetooth Serial port Com7
The XDA only actually has 1 com port (com1) so any other are virtual ports created by various software, you just need to find out which one is the one for the GPS...
So in "tomtom gps v3.07" I go to the gps tab and by default its set to infrared port. I change to "BT on com6" and click OK. When I restart the program it always resets to "infrared port" even if I try a different port. Really am stuck- never had any problems with my xdaII- just put in BT port and it picked it up automatically...
The problem is it's not always the same com port for different devices - firstly does your unit have the widcoom stack version of are you on the microsoft stack..
Whichever you have you need to find where the BT com port is configured..
On my widcomm i go to 'bluetooth setting' ; 'services' ; "serial port'; 'advanced'
in there it says...
inbound com port : 6
outbound com port : 7
so the incoming com port on my bluetooth is 6 hence the 'BT com port on 6' listed in my tomtom gps.
so you need to find your BLuetooth com port and find out which com port number it is set to. Not sure as to why tomtom gps does not save your settings, the only thing I can think of is becuase it never gets a valid signal from the comport select, and does not save the change unless it does.
Also: I assume the gps unti has a pairing with your XDA unit?
So does the widcom stack work on the xdaIIs? If so where can get it?
Sorry: I cannot be certiain the widcomm works with the IIs, but is can be downloaded from this site if you are willling to try, just do a search oin widcoom, and you will find a lot of entries...
For the MS BT stack; look under start, settings,System tab. There is a icon labeleld Bluetooth settings in there you can see/set the com ports for the bluetooth link. they also need to be enabled witch a check box before they will work...
So on "bluetooth seetings" serial port/advanced I have inbound COM port 5 and Outbound COM port 6. Below it says "Default device for outgoing serial connections: TomTom Wireless GPS. Display the device selection screen the next time an outgoing serial connection is attempted" next to a ticked box. I have tried bt com 5 and 6 in the gps settings and it wont save or recognise either. I can, however, pair and connect to the device in my BT manager but Tomtom doesnt recognise it...
Hmmm - all sound ok to me but I currently use a wired GPS, so I have not actually done it. I'm afraid I'm as stuk as you are now...
Sorry bro- I have sorted this now. Thanks...
For me, I just selected Comm 5 from the GPS status drop down and it works like magic!