Database Develop

Error 114, help me please,I'm helpless.

Hi All
I have a SPV M2000.One day the phone stopped working. Everything was all right, it did ask for pin but then didn't even looked for network,was immediately saying NO SERVICE. I tried few sim cards - the same.
So then I wanted to reinstall the ROM, I downloaded the official from Orange UK , tried to install it,and it shows ERROR 114, Radio Rom Upgrade Error.
And the phone now is in bootloader mode and I can't do anything!
I downloaded different ROM from xda-developers ,at the beggining with a country error, but i managed to fix it and now with this ROM it's the same thing. ERROR 114. I tried everything, hard,soft reset, Pc reset etc. Nothing works!PPC still in bootloader mode!
Please tell me if you know what else can I try!

Guys,come on,really noone knows???

Have you read WIKI? Follow the first method to flash your ROM. Have you remembered to plug in your power supply to your cradle when you flash your device?
Heres another thread on NO SERVICE Plz help... No Service after radio upgrade. Happened to me. Read it and see the advise by MDAIIIUser and TheLastOne. If all else fails, bring it to the shop.

I had a very similar problem....
First I tried to update a whole package that means rom, extended rom and radio
The radio update is always the first one and there always upgrade error 114 occured.
So I updated every part seperately and it works except the radio. So I tried alot but it just didn't work..even downgrading was impossible. MDAIIIuser and happy goat tried to help me as well as they could but nothing had an effect.
So I read in another forum that asus mainboards have some problemes with these radio updates....I thought they were joking...but I tried the radio pdate at another pc and it worked!
I know it sounds a bit stupid but I was desperate and at last it worked!
You can read it here :
http://forum.xda-developers.com/viewtopic.php?p=89657#89657

TRied that method.Doesn't work
Any other ideas?
One more thing.Is it normal that in bootloader mode when I plug the power cable in the charging LED is not working?it was working before.
The battery is charged ,but shouldn't it show that the power is connected anyway?
EDIT: this is a reply to the first answer.
So you think I should try on another PC?I will today!Hopefully it will work.

So I managed to install new rom on a different computer! I think that there was a problem with active sync.I used the one that was installed from my old XDAII.Could that be the reason?Now i installed the one provided with a M2000.
But it doesn't work anyway
Still NO SERVICE message.
ANy other ideas different than taking it to Orange?

Hi rottie,
No Service could mean anything. Could your SIM card be faulty? Device SIM locked? Or hardware faulty? You cannot just use any ROMs you find at ftp. Try to flash your device with full shipped rom at http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade. Use the first method and upgrade using MaUpgradeUt_noID.exe to bypass the Country code error. Remember that you'd need to run MaUpgradeUt_noID.exe twice.
Read wiki carefully, it has alot of precious information. Cheers ^^

Before you update any version you should be sure that your radio is
compatible with your device. Usually all radio upgrades should be
independent off the language of the device but as I understood (could be
wrong) there are differences because of the servicenetwork frequency.
So you must be sure that the chosen radio is compatible and that your
device is not simlocked.
So perhabs you should chose an upgrade of your provider.
But perhabs itis better not to risk your guarantee of your provider by
using updates or components of other providers! Because there could be
the possibility that your device is damaged and you should bring it back!
Good luck!

Guys, you get me wrong.I'm not trying anything what I'll find.
1)One of the ROMs that I tried and the one that I left now is a ROM downloaded from orange.co.uk for SPV M2000. So there can't be any incompatibility, don't you think?
2)I have 2 sim cards,both from Orange,I was using both of them before in my M2000 which is sold only through Orange so there can't be any simlock problem,don't you think?
3)I used only that orange ROM, original and the I-Mate one.None of them were working good,always NO SERVICE.
I bought the phone second hand,with box,all accessories etc. But I don't have a receipt :? And of course have lost the guy's number.That's why I want to try everything before going to the service.

I think this phone is network blocked, probably been reported damaged or stolen, once the insurance or replacement is issued a block is put on the imei of the phone that was subject to claim.

PLEASE help - In urgent need of support

Hello
I have an XDAII1 PH10C
Ive had a few issues with TomTom etc and have downloaded an update or two - including the official O2 update.
Unfortunately me XDA keeps freezing and Im getting pretty upset with having paid £400 for nothing.
When I did the O2 upgrage I got the following :-
The file "rofs_target.zip" was not copied sucesfully. To re-install, you will need to get the source .cab file again. Continue with Setup?
Ive even let both batteries run down completely in the hope of restoring original O2 set-up - but I get a Country Error code when I re-install the upgrade.
My hardware settings are :
ROM 1.11.00 WWE
Date 01/27/05
Radio 1.04.00
Protocol 1337.42
ExtROM [this is blank]
Ive got the chance of returning to O2 support to try and sort problem, but I need original O2 set-up or they will charge me £96+vat for re-setting XDA.
PLEASE - does anyone have solution for solving [blank] ExtROM issue or the original O2 settings to solve the repair bill problem.
Thanks
Paul

what types of sd card are you using
sometimes i get that error as well but all i have to do is re run the no id app and it works 2nd time

I have a PQ1 1GB card, but dont have that inserted when I download updates or reset PDA.
Paul

re-run the O2 update if it errors with country ID error then just start it back up again it should then work.
It looks from the specs you posted your using the latest 1.04 radio. i assume you installed PUGs new update version ?

Hi
Yes I tried Pugs version, and the ExtROM was still blank.
So, Ive gone back to an O2 version - and the ExtROM is still blank.
I need to reassure myself that I have ONLY O2 software on the XDA before I send it in for repair as it will be free - if they find any other stuff on there they will charge me c£100.
Paul
PS Im still having major TT5 issues. Today it froze and I had to hard reset and then tried to re-install TT5. Only to be told it was already there and did I wish to overite. When I said yes, the today screen came up and theres no sign of TT5 anywhere.
Bloody XDAIIi is doing my head in.

Have you downloaded the latest O2 ROM from the XDA2i mini site?
When you are installing it have you got your anti-virus software turned off?

Yep - O2 download.
Yep - AntiVirus, Internet Security & Anti-Spam all Off.
Ive just done the download again and still got the rofs_target.zip message.
Paul

Hi there, have you tried unlocking the extended rom by any chance? This will cause the storage to be locked and cause the extended rom to stop installing past a certain point (Happened to me). There are instructions on this site on how to unlock it, do a search for unlock and my screen name (pug).
Hope this works.

Pug
I found the link you refer to and downloaded the exttools.200.exe and ran it on XDA.
I then tried the official O2 update again and the XDA has FROZEN !!!!
It is now stuck on Serial v1.01 and WILL NOT alter no matter what I do.
Ive soft-reset, hard-reset and done the soft-off-action button thing - and nothing.
When I place in cradle, the PC plays a tune as if to say it knows the XDA has been connected, but I cannot get activesync to recognise the XDA.
Now what can I do please ?
Im particularly worried that I now cant remove the exttools.200.exe from the XDA and will have to return it for repair with that dodgy software on there - they will definately be charging me for a repair now.
What can anyone suggest please ?????
Paul

New Rom 2.24 for Wizard/Mda

Hi folks
i have found this new rom for mda some where else but i have tried it and it is good
so if any one is interested but like i always says
TRY THIS AT YOUR OWN RISK ... ANYTHING WRONG WITH UR PHONE I WILL BE NOT BE HELD RESPONSIBLE .. i did not made it i found it on the net so sharing with everyone
http://www.mininova.org/tor/328000
it is a torrent link please can someone upload it for everyone in here
Thanks

this says for testing only not for resale when u bootup ..eh ill wait for a custom one of this

This is courtsey of straightgeek and chesney09 on hofo (torrent thanks to straightgeek). I'm putting it in the uploads section now won't have time to try it for a few days =/
Specs (from demota on hofo) :
ROM Version: 2.24.10.1
ROM date: 4/17/06
Radio version: 02.25.11
Protocol version: 4.1.13.12
ExtRom version: 2.24.10.101
OS is 5.1.195 (Build 14955.2.3.0)
Java midlet built in
Don't forget this is completely untested
ftp://xda:[email protected]/Uploads/Wizard/ROMS/Untested t-mo 2.24 beta/

Works great so far. I posted some info on it so far on Hofo.
http://www.howardforums.com/showthread.php?t=924866&page=1&pp=15

anybody else tried this rom?

Possibly stupid questions but I'm kinda new to this alternate rom buisness.
Assuming I don't let it do the customisations and then put in the custom cabs for the GPRS, MMS etc from my existing EXT_ROM would there be a problem installing this on a UK MDA (on the UK T-Mobile network) ?
And would I be able to reinstall the UK shipping rom if things wern't to my liking ?
Cheers

i have a updated it and so far it works gr8 and yes the credit goes to the original uploader for this rom
but more feed backs are always welcome from everyone who will be tryin it out

ruined said:
OS is 5.1.195 (Build 14955.2.3.0)
Click to expand...
Click to collapse
So we've previously had it confirmed by a Microsoft Employee (in a blog post regarding displaying of that retarded builtin battery meter on the today screen) that when we look at the above line from "About" in Settings -> System -> About that the last 3 digits indicate the AKU version. So this means that this ROM has AKU v2.3

Anyone know how I can extract just the Radio rom from this? or can someone post it please as an EXE. I am so sick of 99% of all my calls being ended at or around hte 7 minute mark and again at 14 minutes about 50 percent of time i lose signal and the call and it comes back in a minute or two. the radio on this device is lackluster at best.
any help would be great.
im using the 217 rom with the 112 radio and its the same as the 217 radio pretty much love to try this new radio to see if its better.
thanks
Don

A2DP ???

New Rom
I flashed my wizard with this Rom and everything seemed fine. After about 30 mins of use and once I had re-installed my apps (pocket plus, tomtom, voice command , total commander) i noticed very poor startup times on applications.
To start TomTom it took 55 seconds.
Anyone else have this problem?

rookery said:
A2DP ???
Click to expand...
Click to collapse
It is so easy to add, why is it an issue?

K-Jam upgrade
:x Please can someone tell me how to get around the following issue:
When im trying to upgrade my phone it goes through the normal steps and then i get an error msg saying something about invalid vendor id.
Please help, i would like to upgrade my firmware. For some reason my phone decided to stop playing sound. I can only hear somebody or the phone tones if i plug in the headset. Once plugged out there's no sound. It vibrates only.
Please HELP!!

Re: K-Jam upgrade
anti-kjam said:
:x Please can someone tell me how to get around the following issue:
When im trying to upgrade my phone it goes through the normal steps and then i get an error msg saying something about invalid vendor id.
Please help, i would like to upgrade my firmware. For some reason my phone decided to stop playing sound. I can only hear somebody or the phone tones if i plug in the headset. Once plugged out there's no sound. It vibrates only.
Please HELP!!
Click to expand...
Click to collapse
For your first issue, search the Forums for CID Unlock, LokiWiz or aWizard...
For the sound issue, I've read posts where other users have experienced hardware failure of the 'switch' indicating that you have a wired headset plugged in. Without the headset attached does the headset graphic appear on the phone dialer screen? (might have to call voicemail to be sure)

Re: K-Jam upgrade
anti-kjam said:
:x Please can someone tell me how to get around the following issue:
When im trying to upgrade my phone it goes through the normal steps and then i get an error msg saying something about invalid vendor id.
Please help, i would like to upgrade my firmware. For some reason my phone decided to stop playing sound. I can only hear somebody or the phone tones if i plug in the headset. Once plugged out there's no sound. It vibrates only.
Please HELP!!
Click to expand...
Click to collapse
Your phone is probably locked. You need to unlock it first. Read this:
http://forum.xda-developers.com/viewtopic.php?t=41453
downlad lokiwiz 0.2b here http://forum.xda-developers.com/viewtopic.php?t=33796

Sound Issue
Ok, i have phone my voicemail but do not see any headset icon. But normally there's no icon on my phone. I cannot enable speakerphone. It was working this morning. I then plugged my headset in and after i unplugged it the sound was not working. Any ideas??

Unlocking
:x Now when i choose unlock cid the phone reboots after finished, but when i want to upgrade i still get the vendor id problem. Ideas?

Re: Unlocking
anti-kjam said:
:x Now when i choose unlock cid the phone reboots after finished, but when i want to upgrade i still get the vendor id problem. Ideas?
Click to expand...
Click to collapse
Are you already running one of the 2.x Roms? CID unlocking does not work on them. You will need to downgrade to an earlier 1.x Rom, CID unlock and then upgrade. {Gentle nudge} all if this info is avaliable by reading the unlocking threads.

Anyone have an idea where I can get this Radio Rom i have been looking all all day but have come up empty.
thanks

I think this is a modify/updated version of the US ROM as it has alot of US ralted cbs in the Ext. ROM and also it's missing some of the EU features.
But it's fast and it's stable, add some of the EU specific features and I'll have the perfect ROM. Please TMo, do hurry.

Forcing Bootloader Mode

Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!

this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm

Thanks buddy!
I'm happy that worked for ya!
Take care!

I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?

Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse

My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.

I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.

Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse

It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse

Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.

In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?

Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse

Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....

Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse

I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)

Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.

Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.

Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.

Worked great. Back to T-mo she goes!!!

BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.

Hang in bootloader

Hi @ all,
**** happens, yesterday i tried to upgrade my rom on charmer (mda compact 2).
During installation system hangs on and didn´t finish.
So now i have only the startscreen and can reach the bootloader.
Tried now to flash an original rom, the ruu says error 294 invalid vendor id.
Otherwise the ruu (for no id) ended with error 238 file read.
My bootloder shows IPL 1.12, SPL 1.12 and USB connected.
I have read a lot of threads but cant find a answer for that.
Has anyone a good idea?
Thanks a lot for helping.
I wish all users in that great forum a happy new year
ronni

Hi Ronni,
same problem here. Do you found any solution?
Is it right, that your Device not charging and USB is not recognizing too?
Bg
Joy

Are you trying to flash WM6 ROM to your charmer? Because WM6 required IPL and SPL level at least 2.xx.
Did you tried this method to bring charmer back to life?

wow, thank you for your quick response. Hmm, I´m not shure, it´s a PDA from a Collegue, I don´t know, what he do with it. (I know only he try to flash something) Next week he take it to our office, then I try your solution
Thank you again
Joy

Bootloaderhang
Today i tried to update my rom... while the update i had an error.
i had updated the http://forum.xda-developers.com/showthread.php?t=363882
after the hardreset the phone hang by the first screen. I can press everething but nothing happens.
now I tried to flash a nother rom but it is unpossible because it can´t connect with windows mobile center on the pc.
Has anyone a good idea?
Thanks a lot for helping.
I wish all users in that great forum a happy new year
didi500