sx 66 dead..please help - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hello, I am new to this site and the whole BA experience. I got my sx66 about a week ago and decided to upgrade the ROM to 1.33.51. Yes, from what I've gathered from reading it is also a little out of date, but I was trying to start out small. Well, at some point things went terribly wrong, everything seemed to be well, when all of a sudden my screen went blank and I was left with a screen that just says serial at the top and v 2.07 at the bottom. I have left the battery off for about 20 hours now, waitting on the backup battery to die(from what I understand my phone may be stuck in bootloader mode and this should fix it) Well, I just got home from work and the phone still says the same thing if I put the battery on. Any help or suggestion would be appreciated or even just a "Hey, your phones gone" would be as well, just curious to know what to do. Thanks!

Yes, you're in bootloader mode. It's now ready for upgrade.
If you put it in cradle, it will change from 'Serial' to 'USB', run the upgrade and do the (Record,Camera) reset with 'no,yes,yes' and press 'Mail' button.
Most of these are in the Wiki.

Related

Radio Upgrade rendered PDA2K useless! Newbie needs help!

Well, I took a chance and this is what I get. It's 10:46pm and I have a PDA2k that won't even turn on now. Removed the battery and the whole thing.
Here's what happened, I have a PDA2K from Expansys. I decided to upgrade my radio from .06 to .10. I read every article regarding this and backing up very well. I took the instructions from http://wiki.xda-developers.com/index.php?pagename=BA_Radio_1.12_Upgrade and proceeded with the backup. I did the soft reset, and put my system in the cradle. A hot-sync took place. I then went to my folder on my desktop, clicked BAupgradeut.exe and I got the screen that popped up. I followed the instructions and clicked ok. It read my old configuration and what was going to be changed, and I clicked next. Up popped a screen saying checking information on your device...then my Active Sync shutdown, XP detected a new device and said it was ready to use. I noticed that the power light (charge light) on my PDA2k went out (yet there's power to the outlet) and Active Sync never came back on. I thought "this can't be good" but proceeded to wait 20 minutes, tried to get active sync working again and it couldn't find my unit. I finally tried to kill baupgradeut (and it's still up and running with the same "checking your information" screen. I finally said screw it (after 25 minutes) and yanked my pda2k off the cradle. No power, can't do a hard reset...nothing works at all...its completely dead. Tried pulling the battery off for a couple minutes and that didn't help either.
I'm pretty stuck here and hope you guys can help me out. (Even though everyone is probably asleep.) So, I've got a really nice paper weight here. If anyone has any thoughts, pass them on over. I chose the 1.12.00 upgrade from the same page as I mentioned above if that helps. I guess my main concern is just being able to get some response from this thing. Right now I get NOTHING.
Thanks,
Tom
Now I feel like a silly twit! Turns out I had a grey screen and was in bootloader mode. Its not too bright in this room tonight and I didn't see that...could have something to do with the 4 Guinness I had. I noticed it when the light reflected off the screen. I checked the troubleshooting guide and discovered the "grey screen" problem.
I just finished the upgrade and am setting things up. Everything's just peachy.
Sorry about being such a baby. I have insurance on this too. I could have just run over it in my Land Rover and got a new one....those trucks really flatten things.
Question: I used Sprite to backup just before I did this. Can I restore without jacking anything up?
Thanks for what I'm sure would have been a lot of help and support.
Tom
twn2 said:
Question: I used Sprite to backup just before I did this. Can I restore without jacking anything up?
Thanks for what I'm sure would have been a lot of help and support.
Tom
Click to expand...
Click to collapse
Tom,
You might want to read this thread.
http://forum.xda-developers.com/viewtopic.php?t=20891
Hope this helps.
Hemant.
Hermant - Thank you very much for your reply. I just wish it came 13 hours ago.
I found it on the xda-developers somewhere that someone else posted. I was trying to find your link which I stumbled upon before. But alas, I found something. It required that I use GetData before the upgrade, which I didn't do. I followed the rest of the directions (which was similar to your link) and everything is perfect. My Radio and BT upgrades are still there. Thanks again for the help! I bookmarked it this time
Tom
Tom,
Actually even i had found this link here but now i have tried it many times and it is working perfectly.
Glad that i could help someone since i have learnt a lot from this site so now is the time to give back.
Hemant.

Screen get's messed up with Helmi BA WM2k5 AKU2.6 during charging

Hi,
I have a Qtek9090 which I upgraded yesterday to Helmi BA WM2k5 AKU2.6 Beta (v.1.1.2 Beta).
Everything went fine and I do like it (apart from the usual problems with WiFi, BT,...).
However I got into a shock-state when I turned it on this morning after leaving it in the craddle during the night for charging:
It would turn on, but the screen was completly f..ked up!!!
I did a Softreset -> screen still messed up
I did a Hardreset -> screen still messed up
I did reflash the upgrade -> screen still messed up
I took out the battery for half an hour and put it back -> still the same
After many resets and so on, suddenly I got the color stripes again and the phone booted normaly. I did not even loose any data.
Next I put it to charge again and after a while (the screen went off meanwhile), I turned it on and guess: scrambled screen again.
This time, I did the Reset this way: battery-notch off, kept the Softreset pressed and simultaneously put the battery-notch on again.
Is this a known problem (shouldn't be - I searched the forum!)?
Why does this happen?
Any ideas???
Also, I have these questions:
- What is this selection one has to do after the upgrade for (2. and 3. item YES)? What should the first item be: YES or NO? Can this be the cause for my problem?
- Would it be wise to downgrade again? (In case this is a defect -> so I can try to claim warranty, if things get worse...)
- What is the patch for energy management for? Where can I download it, as the link in the Wiki does not work? (Has this to do with my problem?)
Thanks,
vma
The problem remains.
It does not seem to depend on the charging, but happens when the device is turned off for some time.
When I turn it on it will either work fine, or funtion with a wild flickering screen.
Arrggghhhh!!!
Am I the only one with this problem?
Cheers,
vma
Hi,
Some month have passed on this issue. The reason I did not post about it, was because I had to send my BA for repair and one never knows if the "enemy" is listening... Now the warranty has expired anyway and mey BA is fully working.
It may have been a coincidence, but one day after the upgrade the screen went mad and totally messed up. Only 1 Hardreset in about 100 tries would bring it back to normal for some period of time and even reflashing it with WM5 or 2003SE would not make it work normal again.
The screen would get messed up suddenly for no particular reason, normally during a standby.
At the end I had to send it in for repair, which was actually a good thing, as I complained about the loose stylo and bad working hardkeys, all within warranty.
I got a new key-pcb, backside and they reflashed the device with 2003SE.
I am almost sure that I must have done something wrong with the upgrade to WM5.
Strangely I was able to flash 2003SE onto it, though it did still not work properly: hours with messed screen and sometimes out of the blue I would turn it on and the screen was OK again for a few hours.
Could it be a bad cable connection, which got repaired as well? Was it just a software problem?
One of the things I was in doubt with: when you enter this menu to format the device, the instructions say to switch two options, but the menu on my device had three options. Sorry - I do not exactly recall the details.
Anyone with an idea, why my device went mad?
As a side-note: while WM5 was great, while it worked during the one day it worked. I specially liked to be able to turn the device completly off or being able to remove the battery without loosing data.
However: not having my beloved BA fo two weeks made me reconsider doing experiments on it. Since I have it back I did not reconsider flashing it again.
But I would like to understand what had happend...
Cheers,
vma
May I assume from the lack of replies, that this was a pure coincidence on my device?
Nobody else experimented this weird problems after upgrading to WM5?
I am considering upgrading my phone again, essentially because I am tired of being afraid of discharging the battery and thus losing all data...
Cheers,
vma

Did I do what I hoped I wouldn't?

Well, after hours of research and searching and reading, I finally decided to flash my T-Mobile Wing. Yay! First, I did Hard-SPL from HERE and followed the instructions to the point. The CanonYang splash screens came up and my Wing loaded into Windows Mobile just fine. From there, I installed ASerg's policies again and ran Itje's Touch-IT Lite for the Wing "1__UPGRADE_ROM.bat" and followed the instructions it prompted me with. An error screen came up on my phone saying "Unknown Status" but I just left it alone. After about 10 minutes, Itje's RUU completed and I hard reset my phone.
Now, only the first CanonYang splash screen comes up and my phone locks up there. Did I just brick my phone? What do I do to fix this?
Any help is greatly appreciated.
*EDIT* In my haste and fear of the "brick", I chose to post a thread rather than do the obvious that many will most likely state. If it helps my situation, please note that it's nearly 5am in Chicago, I have not slept yet, and I'm pretty much terrified I just made a $300 paper weight. I'm certain many of you would do the same.
Yes, I did fix my problem... and yes, I found my answer by searching the forums... and yes, I will buy you all cookies! Itje gets a candy bar though
lol soz
press the camera button and at the same time use the stylus to push the reset ..... a colourful screen will come up ...... connect it to your computer and run a official rom..... you can either look from some or get windows mobile 6 from htc.com if you sign up to the eclub and just find it from there.
hope this helps

Any Merit To What I've Done? "Crashed" Tilt2

Hi All,
While on a business trip last week, my Tilt 2 (at the time, running the April 14 Energy ROM), my phone--for lack of a better word--crashed on me.
Everything had been working fine, I was sitting there with my phone connected to my laptop via a USB cable, and out of the blue, for no apparent reason, my phone re-booted, and never came back up. It would get to the splash screen, start loading the OS, reboot mid-stream, and get stuck in a loop. Weirder still, if I pulled the battery, let the phone sit, then put the battery back in, hitting the power button did nothing--even with the phone plugged in to power. On top of that, even if the phone was off, after a few minutes, it would power itself back on randomly, and get stuck in the re-boot loop. Very weird.
So, when I got home, before heading to the AT&T store and asking for a replacement, I thought I'd try to restore the phone myself.
At first, I pulled the battery, then stuck it back in, and sat there holding the volume down button, waiting to put the phone into bootloader mode. That worked, but even in bootloader mode, it would randomly re-boot. So, I started the process again, and immediately plugged the phone into my computer while in bootloader mode and ran the Task 29 tool. That completed properly.
At this point, I popped in another battery I had laying around and just let the phone charge for a few hours. Then, for the heck of it, I re-ran the HardSPL tool. Re-Flashed to the .91 radio (it was already on the phone), and then flashed to the latest Energy ROM.
Since then, my phone has been better than ever. Seems faster, battery life is better (Went three days without having to charge it), no dropped calls, and no weirdness with the latest ROM (that I've found so far).
Does it pay to REALLY start fresh from time to time, and re-flash everything on the phone?
Thanks for any input.
I have no idea, but hopefully the WinMo experts will see this and have an idea, so here's a bump for you. Most of my computer expertise revolves around Unix, Linux, and a bit of Windows, not so much these phones.
I do know that task 29 is awesome, though. It seems like DBAN for your phone...
DBAN=Darik's Boot and Nuke. Look it up.
I don't know what happened with your phone, sounds like something broke in the area of booting.
I don't think you should need to re-flash HardSPL radios just for the sake of it, but I'd strongly recommend task29 every time you flash a new ROM.
bricked my TP2
My TP2 seems to have a similar problem which I haven't been able to fix it just yet. The bootloader reboot loop is too short to succesfully run task 29 and flashing it using the microSD gets stuck around 40%
during bootloader mode there's an unreadable errormessage since it's on the same line as some of the usual information.
any thoughts/suggestions would be very welcome since i can't afford to send it to the factory.
cheers.

[Q] Can ANYONE help me fix my bricked Pure?!?

By the way my phone is a HTC Pure, that was security and sim unlocked, at the time it went down was running the latest Energy.TOPAZ.29022.Sense2.5.Cookie.2.0.GTX.Jul.04.7z ROM. With no recent updates or installs.
Ok my phone was in my pocket for the morning and when I pulled it out it was dead and wouldn't turn back on. Plugged it in to charge and once charged it will only boot to the white screen with the little red numbers in the bottom. It takes very little time to get to this point and once here it is unresponsive to any buttons pushed. I can leave it like this and it will just get hot and wear down the battery, I have only left it like this for ten minutes, just to see if it would come out of this stage.
After searching and reading all the brick / won't boot posts I could. I tried to hard reset, which works and I can get to the bootloader screen(striped screen). Then re flashed to the newest hard spl and have flashed three different versions of Energy, currently trying MaxSense. But nothing has gotten it past the boot screen. All flashes were done with the USB through my computer and the SIM and SD cards have not been in it.
I just don't get how it bricked in my pocket, it had worked fine for a month on the same Energy ROM with no issues and I had not downloaded or installed anything new recently.
Just miss my phone now, any help would be greatly appreciated.
Did I post this in the wrong area? 3 days 50 or so views and nothing, this sucks!
I take it this is the wrong area for this post as it has gotten a few views, but no responses. I should probably move it and see if that helps.
This sucks and I am disappointed, I'm done with this post, I give up!!!
I have a paperweight for a phone and I hope no one else has this issue, because no one on here can help.

Categories

Resources