Screen Alignment Problem - Tilt, TyTN II, MDA Vario III General

Coming from a P3600 I did read about the TyTN´s screen alignment issues. Nevertheless, I figured that it can´t be the TyTNII will have similar problems.
Well, mine does.....
Pressing one spot on the screen occasionally activates another. Easily recognizable when drawing: I just put down the stylus and instead of a dot I get a line.....
I´ve tried the bussiness card trick but no good. Will wait for the Brando screen protector to arrive and see if it helps. (Right now I have the HTC shipped protector installed, which is a rather poor solution)
edit: new findings:
1. only the left 25-30% (portrait mode) of the screen is affected
2. By pressing fairly hard on the screen I can duplicate the problem in 80% of the attempts
3. Have adjusted the registry value for screen sensitivity to 250......light to normal presses register correctly 95% of the time.
Using the finger instead of the stylus I have 100% success rate
4. Don´t really want to send it in yet for fear of the repair guys just doing a hard reset, testing for 5 seconds and sending it back

Hehe, i got scared at first, i'm pretty sure that's connected to the finger scrolling and is not a hardware issue. You can try to disable TouchFlo (in registry, i don't remember where exactly) and see if it helps, i'm pretty sure it will fix it
About the finger issue: even if we don't get the HTC Touch hardware that detects finger (or so they say) our Kaiser kinda detects finger too, at least i feel like it does, so this strengthens my point about this being connected to TouchFlo

Related

Screen Align not working? DOA?

Hi, Just got my MDA Vario III, and it appears the screen alignment that WM runs on first boot will not work. By that I mean its asks me to align the screen, but it will not register the taps with the stylus or fingers.
However, it does know when I touch the screen as it brings it out of powersave. I downloaded this Remote Screen Alignment program, which is able to skip the screen align process, but then when I have done that the taps from the screen are all over the place - because the screen hasn't been aligned. The keyboad works fine for navigation around the menu's.
Does this sound like a DOA device? Or am I missing something stupid?
foaf said:
Hi, Just got my MDA Vario III, and it appears the screen alignment that WM runs on first boot will not work. By that I mean its asks me to align the screen, but it will not register the taps with the stylus or fingers.
However, it does know when I touch the screen as it brings it out of powersave. I downloaded this Remote Screen Alignment program, which is able to skip the screen align process, but then when I have done that the taps from the screen are all over the place - because the screen hasn't been aligned. The keyboad works fine for navigation around the menu's.
Does this sound like a DOA device? Or am I missing something stupid?
Click to expand...
Click to collapse
It might be a simple loose connection or something trapped between screen and bezel. But I would not be even thinking about that, it would be going straight back under warranty. Thankfully, this is not a common problem with the Kaiser and I think you have just been unlucky.
I assume you have not put on any screen protector that might be causing this behaviour> Otherwise it is a DOA and nothing you can/should do other than return.
Mike
Thanks. I hope its not common! No screen protector, but I did try one first before first boot. I immediately removed it when the taps weren't working. I'll send it back tomorrow, thanks.
Dont tap. Just lightly drag the end of the stylus around each target until it proceeds to the next one.
It's common and should be fine.
Thanks unwired. Whilst that does get a response from the TyTn II, and moves the align crosshair, unfortunately it just loops the alignment process indefinitely. Arranged an exchange with T-Mobile without a problem
foaf said:
Thanks unwired. Whilst that does get a response from the TyTn II, and moves the align crosshair, unfortunately it just loops the alignment process indefinitely. Arranged an exchange with T-Mobile without a problem
Click to expand...
Click to collapse
If the future device does it, just try what I suggested but be as accurate as you can.
Unwired's method works for me as well. My Kaiser always seems to lose the ability to detect stylus presses (but finger pressure works) every time I use it on a plane which I assume is due to the cabin pressure. When the screen is reset, everything goes back to normal. Has anyone else noticed this, or do I have some defect that is only going to get worse?
I got the second Kaiser, and it happened again. But I immediatley used unwireds method, this time being extremely precise and only moving the stylus slightly. It works fine now, and stylus accurancy seems to be ok.
I still think it's strange, as I have had an HTC XDA before and a tap was sufficient on the screen align process. Furthermore it clearly states "tap screen" not "tap and drag".
My last three Wm devices (Prophet, Hermes and Tytn 2) have all been reticent to respond to alignment taps... but carefully moving the stylus around the target has always fixed it.
unwired4 said:
My last three Wm devices (Prophet, Hermes and Tytn 2) have all been reticent to respond to alignment taps... but carefully moving the stylus around the target has always fixed it.
Click to expand...
Click to collapse
For me it is more like 'tap-and-hold'. I make a firm tap on the '+' symbol, then keep the stylus pressed on the screen for one second, then release. The '+' then moves to the next alignment point.
Just for the record, I think the problem is common!
I've seen many people who have unresponsive touchscreens, and now I'm one of those unlucky people. And nothing works. And I don't have warranty because I'm in a different country than the purchase country and the reseller here only services phone bought in the Middle East. #[email protected]$#@$#@

Problem with the touch screen.

I bought my HTC tytn II about a week ago and I am having a problem with the touch screen. Sometimes when I touch for example on the start or on the ok button with the stylus it doesn’t respond from the first time and I must touch again to respond. I have align the screen so that’s not the problem because most of the time it works ok. Can someone please help me with this? Thanks.
Sometimes the corners just need a firmer press where the digitizer layer is held more firmly. So you would need to check whether yours really needs two presses or just a firmer one.
Mike
The problem is not just the corners but the whole screen. Sometimes it just doesn’t respond from the first touch.
After further usage of the device I think it’s not the touch screen that has the problem because when it’s not responding it freezes for about 2-4 sec. and then it’s normal again. Is anyone experiencing this strange behavior? What can it be wrong it drives me crazy! Can please someone help?
My ATT Tilt is doing the same thing. Right now im running the stock ATT Rom with the ATT autoload crap disabled after a clean hard reset.
I notice that when my touch screen stops responding so do the soft keys and function buttons. The device appears to hang-up and **** the bed every once in a while. Its often enough to also drive me crazy as well.

Touch Screen Freezing

I have an un-locked TyTn II that has an annoying screen problem. At least once a day, the touch screen will stop working. The device continues to function normally using buttons and/or the keyboard, but the touch screen function is dead.
In every case, I have been able to revive the touch screen by using buttons to navigate to the screen alignment settings and then use my finger to scroll around the screen till it comes back to life. Once the screen alignment program comes back to life, I align the screen and go about my business.
I have a fair amount of Spb software installed, but I had the same problem before installing any of the Spb software, so on the surface, I'm ruling that stuff out.
I have Kaiser Tweak and Paul's Tweak installed.
Any idea's would be greatly appreaciated.
Maybe this thread will help?
http://forum.xda-developers.com/showthread.php?t=337979
Thanks for your reply.
The thread you provided appears to be focused about "complete" freezing. My device continues to work as long as I use buttons and/or the keyboard. Once I align the screen, the device goes back to normal operation.

Screen Alignment Problem URGENT

I just replaced a screen in a Trinity (Dopod D810). The touchscreen initially wasn't calibrated correctly so I ran the alignment tool in the settings, and after a few attempts, I calibrated it properly and the touchscreen was working perfectly. Now the touchscreen is not working properly. The top half of the screen responds to touch, but no matter where I press in that region, the screen thinks I'm pressing the top-right corner. When I run the alignment again, it responds to all the touchpoints but it never successfully calibrates and it keeps bringing me back to the alignment screen.
The current settings in the registry entry for touch calibration are as follows:
484,558 244,286 263,815 750,820 707,295
I've found a few other threads here (the most helpful being http://forum.xda-developers.com/showthread.php?t=355010) and I've tried the settings from that thread. The screen seems more responsive, but still not correct because the bottom half hardly responds and the top half seems to respond when it feels like it.
Can someone please post their D810 touchscreen settings so I can try it? I've tried the settings from my Touch Cruise, but the screen is still doing weird things.
This is a customer's phone so I need to have this fixed ASAP.
I'm thinking that it may be a faulty digitizer, but that won't explain why it worked perfectly when I first calibrated it.
UPDATE: NOT FIXED yet, but now the backlight is dead. I just turned it off, and then turned it on again, but I can only see the screen content if I shine a torch onto the screen. The LCD hasn't leaked. The backlight just died and the connectors in the phone are fine. Perhaps this was a dodgy screen.
Any ideas?!
since the device has a recessed screen, take the cover off to get at it.
take a soft cloth or something and clean off all the garbage on the digitizer and back of the plastic. make sure everything around the lcd is free of dirt.
usually, if there is something pushing down on the digitizer while you calibrate it, it will totally bork the alignment over the course of 10 minutes to an hour.
my kaiser is currently having this issue, though i put it though alot more hell then i should have... so i suspect its suffering from other issues.

[Q] Screen sensitivity

I am not sure whether it is my mind playing trick with me or not, but I feel like my phone is less sensitive after I did the hard reset (power+volume down). Sometimes I need to press 2-3 times because the first light tap was not detected.
So is there anyway to increase the sensitivity?
I have the same problem, but no idea that is the hardware or only software problem.....
Fresh owner of this Optimus 2X in France, in our community, frandroid.com, we encounter the same problem , I think this is a software issue.
Did someone already contact LG??
Maybe they should include this into the bug list thread.
May I know were you guys having this problem since it is out of the box? or after reset?
I have the same problem started from day 1 till now
I have the same issue and already thought I'd be the only one having this problem.
I would not say it's a problem with sensitivity, but it feels like the touchscreen goes into some kind of sleepmode where then you need to press a second time, to wake it up.
Continuous touching is no problem. (like when typing rapidly on the keyboard)
This video is not from me, but it shows the problem.
Have a look at 13:28 and 13:37. The reviewer tries to hit the "Ackermann" entry, but the touchscreen does not recognize the touch. At 13:37 the guy has to press another time to get the entry selected.
http://www.youtube.com/watch?v=VRid-Yhu7Gg&feature=player_embedded
Yes! The touchscreen is definitely less sensitive than my old HTC Hero, and gets quite frustrating sometimes when a scroll misses the first part of the movement or a click is missed.
Sent from my LG-P990 using XDA App
just in case, are you guys using 20110218 baseband too?
The same problem here. If I unlock the screen and then tap on any on screen apps, I need to touch again for it to open. Only the first time though, after that it function ok. I think this is a bug and needs to be fixed... I have my pc for double-click.
Yep, count me in. Same problem here. Sometimes screen taps aren't registered. Will do some research later on, but I think it's a software problem. (maybe you have to tap 2x as fast )
Hi,
same problem here!
Potentially a driver issue. A Nexus S user had a similar issue in this thread: http://forum.cyanogenmod.com/topic/18431-tuning-driver-to-deal-with-unresponsive-touchscreen/
He managed to tweak the driver and it works fine now. Need to know C++ (I think?) to understand though.
9mmBullet said:
Potentially a driver issue. A Nexus S user had a similar issue in this thread: http://forum.cyanogenmod.com/topic/18431-tuning-driver-to-deal-with-unresponsive-touchscreen/
He managed to tweak the driver and it works fine now. Need to know C++ (I think?) to understand though.
Click to expand...
Click to collapse
I see, then probably they will fix it on the next update/gingerbread?
Same issue here.
Correct me if I'm wrong, but the problem seems to be that the screen has zero tolerance when it comes to tapping and swiping together. If you tap and slide your finger a bit directly after the tap, the tap is ignored. In other words your tap has to be a steady tap when you click on a button or an app. Right on the spot and with no swiping or sliding afterwards. I can't reproduce this on any of my other devices.
Ergo, it seems that the natural tapping I'm used to isn't working on the x2. It seems like I have to adjust my tap. I think that this could in principle be solved with a setting somewhere, because clearly the x2 is capable of registering this in for example a web page.
The great thing of this is that you can safely tap and swipe in the app drawer to scroll up and down or left and right. The downside is that a tap with a little swipe isn't registered at all. I would say that LG has choosen here for a wrong setting.
My personal experience about screen sensivity.. can you confirm if it's the same for your device?
I noticed a strange touch response.. and after some tests, I can say that the touch screen and icons are influenced by the surface where the phone was put!
with the phone in my hands, it's all ok (only sometimes - rare - I need to tap more than once).
If I put the phone over a glass surface (like a glass table) without touching it with both hands, the touch and the icons not respond!! NEVER!
If I put the phone on my scanner the touch screen works ok, but the icons not (or only few and rare taps was detected).!
If I put the phone over my big Onkyo amplifier.. It works like in my hands.. or better!! even without touching with hands.. only with a finger!
Put it back on my glass table.. and all stop working again. If I put a aluminium foil under the phone (between phone and table).. the touch and the icons works again !!
If I put it on the bed.. it don't work.
LG support say that they have tested the phone about this issue after my report.. but no strange response was detected by them. I don't know if they really tested it..
Try it and let me know what you think about!
tested on glass surface, I can press and swipe through pages with a finger without problem.
it is true that my device is not so responsive, but aint reaching that level yet
i read about a similar behaviour on other devices because some devices need a proper grounding for the capacitive screen to work correctly. You can find this problem via google.
Some devices have problem in a car-mounting, for example.
But i think thats not the problem the thread-opener talked about?
Guys I'm looking to get this phone and after reading Engadgets review of the X2 where they mention that the screen is not as sensitive to the touch as other phones I got a bit worried and started googling which lead me here!
Is this true? The screen isn't very sensitive and you have to apply more pressure than other capacitive phones?
I know that the OP is talking about a different issue but I reckon LG will get that sorted out via software update, or at least hope so!
Please do post your experience about the screen sensitivity of the X2 as this is putting me off. I currently have the Motorola Milestone 2 which is very sensitive to the touch even with a screen protector on it.
Cheers

Categories

Resources