Database Develop

thought I wasn't a newb, guess I was wrong.

Alright, so I've been lurking on this forum for quite some time now. I've flashed, reflashed roms. I thought I had a handle on everything but I guess I was wrong. I've been away from a Window's computer for quite some time now. And I recently saw the new 3.3 rom from the gods of xda. Well, I downgraded, to button's 1.01. and then here's where i screwed up. i forgot to go back up to a 2.xx rom. and went straight for the gold and went for the 3.3. yes i know i screwed up. well here's where I'm at now. still stuck with Button's 1.01 ipl/spl but i have the 3.3 OS. And now I'm not getting any active sync connection, my computer isn't recognizing my wizard. also. my 8125 is slow, i mean i tap the screen and i get nothing re-tap nothing eventually nothin happens, and it's stuck on the today screen. I should also mention it's G3, and yes, i unlocked it all the way. so now I'm basically stuck on the today screen with nothing to do. I foolishly finally tried to clear the storage and start from scratch, but now I'm stuck with no extended rom i believe, all the settings are wiped. am i screwed or what? Or does anyone know a way to at least get active sync back up and running, shouldi re-install it? alright so correction, I'm seeing that all the settings from the extended are showing up (i.e. the battery settings on the today screen, the one-touch voicemail/ 411 connect.) so any suggestions.??
edit--
also when booting up, it takes for ever. litteraly 2-4 minutes. And i tried soft rest via stylus, and then it went to button's boot screen shows ipl spl 1.01 and no radio rom but os was 3.3 and then it would reset showing the same damn beer mug, and then it would do it again. then the screen almost faded away and then it showed the same damn screen again. finally it will go to the crossbow splash screen. and no the battery meter at the bottom is showin -1%

you wizard is not dead yet
I did this...hurry...hurry, hurry but there's somethin' that you can do. Try flashing again button's rom by entering your ppc into bootloader, and then attach it to the pc. It will be recognized, and then you can start flashing.
Good luck. And from mistakes we all learn

hmmm
Well I took your advice, put the 8125 into bootloader. And then connected to the laptop. Still no active sync connection, however the 8125 does recognize it I suppose, when I plug into the laptop the USB appears at the bottom left of my 8125's screen.

also
sorry... i hit the edit button in place of quote.
faria

bootloader mode?
i haven't messed up any of my roms personally yet...but i've read in the past that there is a bootloader mode that you can try to enter and reflash your rom from there. maybe it'll work to try and reflash back to the 1.01 rom you started with?
gotta do a search on here to find it...i think it had something to do with holding the comm manager button and the voice dial button and hitting the small button on the right side of the phone between the voice dial and camera button...

waaait
It is how it's supposed to act. It shouldn't charge...it's in bootloader. Just after you hear the "device connected" sound start the button's rom upgrade. that's it. easy as pie
Or you can start with any 2.xx rom. i think it's going to work with that too.

Ok man, I'm such a spaz, alrigh, there's no active sync, but I am running the no id update utility. And it's running on the ppc, so hopefully, I'm making progress.

Exactly what I said
monkey_knight said:
i haven't messed up any of my roms personally yet...but i've read in the past that there is a bootloader mode that you can try to enter and reflash your rom from there. maybe it'll work to try and reflash back to the 1.01 rom you started with?
gotta do a search on here to find it...i think it had something to do with holding the comm manager button and the voice dial button and hitting the small button on the right side of the phone between the voice dial and camera button...
Click to expand...
Click to collapse
That's what I'm trying to tell him. I went thru that. It worked perfectly for me, so it should for him.

anichillus said:
That's what I'm trying to tell him. I went thru that. It worked perfectly for me, so it should for him.
Click to expand...
Click to collapse
It worked for me too.

Boo yah, well I'm back at button.s rom, time to try again. Thanks guys, you've been a world of help.

eightysixfilms said:
Boo yah, well I'm back at button.s rom, time to try again. Thanks guys, you've been a world of help.
Click to expand...
Click to collapse
Also, it's not showing that the 8125 is charging either. On usb, or regular wall outlet. What have I gotten myself into?simply put the device in booloader mode and flash the latest aku2 rom from your provider...this will bring it to live again. due to an hardware flaw wizards cannot be charged with out a proper working OS ....if your battery has drained you need to find an alternative way of charging it and then only you can flash the rom.
ps
activesync is not needed once in bootloader ....

with pleasure
As i said...some mistakes come in handy
@ Faria ... man, I think that if you don't have active sync installed, it won't work... It installs some drivers, the first time it goes into bootloader(for an upgrade 4 example), but it's true that you don't need "active sync" ....course, it's verry possible that I'm wrong...but I had a motorola Mpx200 and it wouldn't recognize it for flash until I've installed active sync

anichillus said:
As i said...some mistakes come in handy
@ Faria ... man, I think that if you don't have active sync installed, it won't work... It installs some drivers, the first time it goes into bootloader(for an upgrade 4 example), but it's true that you don't need "active sync" ....course, it's verry possible that I'm wrong...but I had a motorola Mpx200 and it wouldn't recognize it for flash until I've installed active sync
Click to expand...
Click to collapse
yes you correct you need the driver ..... what i meant to say is you dont need activesync in runing state.......but you do need activesyc in the pc in order to flash.....

thanks guys
Hey, got everything up and running, thanks to all those that helped out, ever in chicago let me know, we'll go out for some beers. But the newrom is up and running and everything seems to be going good. And hey I wasn't torn apart buy the elite on here. So thanks for making me not look stupid. haha

faria said:
yes you correct you need the driver ..... what i meant to say is you dont need activesync in runing state.......but you do need activesyc in the pc in order to flash.....
Click to expand...
Click to collapse
Yeah I didn't know that either, I started to freak once i saw activesync wasn't picking up the 8125. But it's good to know that you don't necesarilly need it up and running.

Tilt Touch Screen failing after loading Dutts latest ROM

Hey there,
A bit new, just finished loading Duttys WM6.1.5.2.1972_Hybrid_V2_1_65.14.06[CubeV2] Rom. Seems great at first. Had to download Goodlink for the corporate stuff. It works fine for a bit, but as soon as an Outlook reminder pops up, suddenly the touch screen is completely dead. Tried all buttons etc on the front. The keyboard works and the buttons can be used as the menu choices, but it took a hard reset to fix it. Which then I had to reload Goodlink and it happened again.
Any patches or settings anyone can think of? Goodllink is the only add in I put in. Any other ROM's recommended perhaps? Thanks all!

Borg7of9 said:
Hey there,
A bit new, just finished loading Duttys WM6.1.5.2.1972_Hybrid_V2_1_65.14.06[CubeV2] Rom. Seems great at first. Had to download Goodlink for the corporate stuff. It works fine for a bit, but as soon as an Outlook reminder pops up, suddenly the touch screen is completely dead. Tried all buttons etc on the front. The keyboard works and the buttons can be used as the menu choices, but it took a hard reset to fix it. Which then I had to reload Goodlink and it happened again.
Any patches or settings anyone can think of? Goodllink is the only add in I put in. Any other ROM's recommended perhaps? Thanks all!
Click to expand...
Click to collapse
I notice this is your fisrt post so welcome. There is a great deal of helpful experience here to help but it does certainly pay to pose questions in the correct place. If you ever have a question about a ROM then post your question in that area and you will be far more likely to get the helpful anser that you want. People are also sometimes too quick to 'Flame' people making such errors - but not me so hopefully this will help:
I am on that same ROM and have noticed that after initial ROM installation that the touch screen is initially 'prone' to what appear to be freezes. In fact I noticed on my device that I had to press quite hard to get any interaction with the screen and sometimes it did not respond.
Cannot say why but this has now completely gone and did so with each ROM install. It took a few soft resets to see the screen working correctly but it is great now! So it may not be your additional software. Just try sticking with it for longer and some soft resets. You might also try tweaking the sensitivity of the screen.
Suggest you search within the correct area and you'll see few comments about this kind of thing (but not many).
Regards

Thanks Tony. My first time posting so wasnt sure where to put it. Have done all you suggested. Worse case, back to the ATT rom, oh well. Will search also and try posting in the right location. Thanks!

Borg7of9 said:
Thanks Tony. My first time posting so wasnt sure where to put it. Have done all you suggested. Worse case, back to the ATT rom, oh well. Will search also and try posting in the right location. Thanks!
Click to expand...
Click to collapse
i just reviewed the software online and i can make several predictions why this is conflicting with the rom. 1) htc home
go to settings>personal>today>items>and uncheck htc home.
let me know if goodlink works thereafter if not I have a few more predictions to why it doesn't operate correctly.
Oh, and i just noticed you had a cube version, which could also be conflicting.

Thanks for the input Red. Tried that to no avail. Even tried soft reset afterwards. It is dead before goodlink even starts. BTW, this will be worth a Pint or two if you get me working.
I thought it might be the Cube version so after several hard resets(storage clearing), I went ahead and flashed it with Dutty's Non Cube version just to see if that was it and it wasn't. I tried tuning the touch screen too, bumping sensitivity up to 200, didnt help either. Tried loading the tweaks program, but nothing there either helped(actually cant even use it when frozen). The keypad, buttons all work, but the touch screen is dead. Hard reset fixes it, loading Goodlink, which I have to have for its a corp phone, kills the touch screen. I believe it worked for a few minutes, then locked up. I need to reverify that just to make sure it didnt happen immediately with Goodlink install. Very strange.

Tilt very very unresponsive today.

Its not letting me receive any calls. Because by the time I press "Accept" it becomes unresponsive for like a couple of mins and the call has already ended.
Its taking forever to load any apps too. It takes forever to open the Programs folder or the Settings folder. Everything takes like a min on the phone now.
I don't know what has caused this. It was working fine yesterday. I haven't installed any new apps either.
I have the HTC stock ROM downloaded from this website. I've had it installed for a few months now without a problem.
Can someone please help me in understanding whats causing this?

I've restarted the phone a few times now. The boot time is around 15 mins for some reason. It stays at the Window Mobile 6 screen for 15 mins before starting up.

Hard reset anyone?

Is that the only solution?
I'm sick of this and slowing turning anti-windows.

Some times things need to be refreshed. Don't be scared, it will be ok.

ashoooo said:
Is that the only solution?
I'm sick of this and slowing turning anti-windows.
Click to expand...
Click to collapse
I know the feeling
Somebody please explain to us that this slowness/unresponsiveness is unique for the TYTN II?! Should I expect the same from a HTC Touch or a Samsung?

ashoooo said:
Its not letting me receive any calls. Because by the time I press "Accept" it becomes unresponsive for like a couple of mins and the call has already ended.
Its taking forever to load any apps too. It takes forever to open the Programs folder or the Settings folder. Everything takes like a min on the phone now.
I don't know what has caused this. It was working fine yesterday. I haven't installed any new apps either.
I have the HTC stock ROM downloaded from this website. I've had it installed for a few months now without a problem.
Can someone please help me in understanding whats causing this?
Click to expand...
Click to collapse
Have you, by chance, been experimenting with network folders? I saw something similar with the file explorer, after I had connected to a network drive at home. It was trying to reconnect while I was away from the home network.

You should expect it from any electronic device like this. Maybe not 100% of the time and not 100% of them, but things like this do happen. There are too many things trying to live in harmony and not step on each others feet for there to never be a problem.
Do a hard reset and see what happens. If it doesn't solve your problem then it's time to look into a warranty claim. If you can use the phone, just backup your numbers and then reset. It's really easy and doesn't take much time to get things back to normal.

Have you, by chance, been experimenting with network folders? I saw something similar with the file explorer, after I had connected to a network drive at home. It was trying to reconnect while I was away from the home network.
Click to expand...
Click to collapse
I didn't touch any of the system folders. In fact, nothing was done to the phone since yesterday except send/receive phone calls and play Solitaire.

If you don't reset it then don't complain.
Click to expand...
Click to collapse
I've done this (hard reset) before and I have every right to complain. Not trying to be a troll, but sometimes I feel I should've bought an iP***e instead.
Right now I'm trying to take a backup of my files on the Storage card, but Total Commander is unresponsive (trying to copy 5 files for the past 30 mins).
I know I'll eventually hard reset this thing, but I'm just pissed right now.

So you don't think people have to hard reset their iphones? I laugh in your general direction.
If you can't make or receive calls, send or receive text messages, or access email or the web
Check the cell signal indicator in the status bar at the top of the screen. If there are no bars, or if it says "No service," try moving to a different location. If you're indoors, try going outdoors or moving closer to a window.
Check to make sure you’re in an area with network coverage. Go to your carrier's website to see network coverage areas.
Make sure airplane mode isn't on. From the Home screen choose Settings, then turn Airplane Mode off.
If that doesn't work, turn airplane mode on, wait 15 seconds, then turn airplane mode off again.
Make sure to include an area code for every phone number in your contacts list that you use to send or receive text messages.
If that doesn't work, turn iPhone off and turn it on again. Press and hold the Sleep/Wake button on top of iPhone for a few seconds until a red slider appears, then slide the slider. Then press and hold the Sleep/Wake button until the Apple logo appears.
Note: If you enter the SIM PIN incorrectly three times, you may need to contact your carrier for a Personal Unlocking Key (PUK) to enable your SIM card again.
If that doesn't work, there may be an issue with your wireless service. Call your carrier or go to your carrier's website.
If that doesn't work, restore the iPhone software. See this document or see "Updating and Restoring iPhone Software" in the iPhone User's Guide.
Click to expand...
Click to collapse

So you don't think people have to hard reset their iphones? I laugh in your general direction.
Click to expand...
Click to collapse
Come on now. You know what I meant. I wasn't trying to imply that at all. I was just venting. Sorry if it offended anyone.

is it possible that its just having trouble reading the sd card (if you have one?) maybe the file system is becoming corrupt on the card and its constantly trying to read it?..

is it possible that its just having trouble reading the sd card (if you have one?) maybe the file system is becoming corrupt on the card and its constantly trying to read it?..
Click to expand...
Click to collapse
I thought about this. I tried using the phone without the SD card. But the behavious was the same. Currently I'm hard resetting it

So how did it go?

Just finished hard resetting it. The phone works now. Fortunately I had an export of my contacts in an XML file (using a .NET utility that I wrote.) Unfortunately, I haven't written the import part of the utility yet
The phone works, but my docs and pics are gone. The SD card works fine. Thanks for your help guys.

Outlook works nice for backing up contacts and there is also a program you run from your phone that does the same thing. I think it's PIM backup

use cleartemp from now on to clear unneeded items on every start up

it is pim back up
its the BEST
ChumleyEX said:
Outlook works nice for backing up contacts and there is also a program you run from your phone that does the same thing. I think it's PIM backup
Click to expand...
Click to collapse

jahrami said:
use cleartemp from now on to clear unneeded items on every start up
Click to expand...
Click to collapse
More junk to cause this sort of problem.

Bootscreen WTF?

Okay, ive seriously tried about every possible thing on here to get my stupid phone to work but heres my situation.
The ATT Tilt i have was working great up until a couple months ago. At one point it just shut off and then went straight to the RGB screen with
KAIS1*0
SPL-1.56.000
CPLD-8
and "serial" on the bottom
Some of you might say "download HardSPL " or whatever and flash from the computer. Problem is I dont have ANY of the software or hardware that came with the phone. All i have is the phone and its charger. Thats it.
Ive tried flashing through the SD card, and it goes to the loading screen. I've used Dutty's, HyperDragon, and the original ROM as a test base. Hyper and Dutty's i renamed the RUU.nbh to KAISIMG.nbh and it goes to "Loading" and thats it. Ive even tried naming it KAISDIAG.nbh and still nothing. Stays there for a while but doesnt go anywhere. I dont know how long exactly its supposed to take to load the damn thing but every post ive seen makes me think that its just "It loads, flashes and you're done"
The furthest i got was with the original ROM i downloaded that was shipped with the phone. Not sure whether or not the version was correct but then again i have no idea what vers. my phone is or where to find the rom that works with it. Anyways, i used the shipped rom, named it KAISIMG.nbh loaded it, said Checking, then says "Not Allow" with some numbers n **** on the top (0028002), then resets back to the boot screen.
No, its not named KAISIMG.nbh.nbh im sure of it.
Its not a kingston sd or none of that.
Ive formatted, used fat32. (however, i cant make it allocate to 512. windows gives it a "default" allocation size which is unknown to me and i cant change it)
Whats wrong with this stupid phone.
Help me please.
ps. Ive searched the archives frivolously and havent really found anything that completely answers my question.

I solved my own problem.
The file i downloaded called "Tilt_RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
Fixed it.
Well sorta.
Since it was an exe i knew i couldnt use it, so i opened the whole thing with winrar, removed the RUU file, renamed it to KAISIMG.nbh and it worked fine!
Well thanks for all the good info throughout the site though. a MAJOR help for someone who thought their $600 phone took a **** on them.

afrodude said:
I solved my own problem.
The file i downloaded called "Tilt_RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
Fixed it.
Well sorta.
Since it was an exe i knew i couldnt use it, so i opened the whole thing with winrar, removed the RUU file, renamed it to KAISIMG.nbh and it worked fine!
Click to expand...
Click to collapse
Only problem is you still have your original 1.56 SPL but now have a WM 6.1 ROM so don't expect plain sailing until you properly update it fully (or have it reverted back to a full WM 6.0 installation).

afrodude said:
Some of you might say "download HardSPL " or whatever and flash from the computer. Problem is I dont have ANY of the software or hardware that came with the phone. All i have is the phone and its charger. Thats it.
Click to expand...
Click to collapse
Heres the software you can download, its all you really need.
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/activesync45.mspx
Microsoft ActiveSync 4.5 is a new software update release for Windows Mobile powered devices that provides a great synchronization experience with Windows-powered PCs and Microsoft Outlook.
Note: Microsoft ActiveSync works only with Windows XP SP3 or earlier. If you have Windows Vista, your synchronization settings will be managed through the Windows Mobile Device Center. Windows Mobile Device Center is available through the Windows Mobile Device Center page.
Supported features
ActiveSync acts as the gateway between your Microsoft Windows-powered PC and Windows Mobile powered device and allows you to synchronize Microsoft Outlook information, Microsoft Office documents, pictures, music, videos and applications to and from your device.

Flying Kiwi said:
Only problem is you still have your original 1.56 SPL but now have a WM 6.1 ROM so don't expect plain sailing until you properly update it fully (or have it reverted back to a full WM 6.0 installation).
Click to expand...
Click to collapse
****.
Yeah. You're right.
My problem now is that once ive reset the tilt after the update, it goes right back into the RGB screen.
What gives now?
I just want the phone to work. Is there a WM6.0 i can download??
If so where?

Go here and just go ahead and upgrade your HardSPL you will be happier in the long run
http://forum.xda-developers.com/showthread.php?t=433835

F2504x4 said:
Go here and just go ahead and upgrade your HardSPL you will be happier in the long run
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Doesnt work for me. I DONT have hardSPL on my phone already, PLUS, i dont have the cables n things to flash it on my computer. I just want it to work normally!
Did you even read my post?
The screen STAYS on the tri-colored screen. Once i turn the phone on, it goes straight to it, and stays like that. I cant even power it off. I have to take the battery out. Soft Reset, just does that; Resets. Ive even managed to get a nbh. file that reflashes it to the original rom. Once prompted for the power button to reset, i press it and it goes right back into the boot screen.
I need a way to COMPLETELY redo my phone through SD.

afrodude said:
Doesnt work for me. I DONT have hardSPL on my phone already, PLUS, i dont have the cables n things to flash it on my computer. I just want it to work normally!
Did you even read my post?
The screen STAYS on the tri-colored screen. Once i turn the phone on, it goes straight to it, and stays like that. I cant even power it off. I have to take the battery out. Soft Reset, just does that; Resets. Ive even managed to get a nbh. file that reflashes it to the original rom. Once prompted for the power button to reset, i press it and it goes right back into the boot screen.
I need a way to COMPLETELY redo my phone through SD.
Click to expand...
Click to collapse
Wow, all that yelling screams I DON'T REALLY WANT SOMEONE TO HELP ME.
Look at the wiki. You can fix it there. YOU'RE WELCOME.

afrodude said:
Doesnt work for me. I DONT have hardSPL on my phone already, PLUS, i dont have the cables n things to flash it on my computer. I just want it to work normally!
Did you even read my post?
The screen STAYS on the tri-colored screen. Once i turn the phone on, it goes straight to it, and stays like that. I cant even power it off. I have to take the battery out. Soft Reset, just does that; Resets. Ive even managed to get a nbh. file that reflashes it to the original rom. Once prompted for the power button to reset, i press it and it goes right back into the boot screen.
I need a way to COMPLETELY redo my phone through SD.
Click to expand...
Click to collapse
Wow and you expect to get help form a community by this kind of response ?
Look you are the one who brought a phone that has developed problems and came here for help...
I cannot help that you do not have what you need, that said go buy the $10 dollar cable BTW it is a commonly used cable so you might all ready own one if YOU SEARCH for it ,
download the proper software that was told to you .
GO SEARCH if this is the kind of response that you are going to give to others that might try to help...
good luck with your phone troubles....

afrodude said:
PLUS, i dont have the cables n things to flash it on my computer.
Click to expand...
Click to collapse
Uh, don't tell us you don't have a standard mini USB cable anywhere... you get one with pretty much any computer device you'd buy. You don't need anything more. As said, do an effort or find your way yourself.

Align screen by-pass

My phone does not suceed on aligning screen and therefore the set-up does not go through.
This happens with any rom I install. I assume is more a harwdware than a software problem, because I noticed some problems in the screen touch even before.
Is there a way to by-pass it and to force WinMo to complete the set-up process?
Thanks

tecmobility said:
My phone does not suceed on aligning screen and therefore the set-up does not go through.
This happens with any rom I install. I assume is more a harwdware than a software problem, because I noticed some problems in the screen touch even before.
Is there a way to by-pass it and to force WinMo to complete the set-up process?
Thanks
Click to expand...
Click to collapse
What problem do you have? Is the aling screen proces start all over again after finishing all five steps? Sometimes I do the screen alingnment over four times. You should press right in the center of + with your stylus, and do not shake even a little bit because it will start again when you finish.
If this isn't the problem, hope someone else could help you, even that I don't believe it is possible.
Good Luck!
Cheers!

tecmobility said:
My phone does not suceed on aligning screen and therefore the set-up does not go through.
This happens with any rom I install. I assume is more a harwdware than a software problem, because I noticed some problems in the screen touch even before.
Is there a way to by-pass it and to force WinMo to complete the set-up process?
Thanks
Click to expand...
Click to collapse
not sure if it will work on x1 but worth a shot.
turn off device
plug in usb cable with PC
start device
when active sync is loaded, go to main storage\windows\startup\ and delete welcome.lnk
lev phone on like that for a good tem min. then softrest

agent_47 said:
not sure if it will work on x1 but worth a shot.
turn off device
plug in usb cable with PC
start device
when active sync is loaded, go to main storage\windows\startup\ and delete welcome.lnk
lev phone on like that for a good tem min. then softrest
Click to expand...
Click to collapse
Should work, but if i'm not getting this wrong this will also not let you run auto customizations

killer8nl said:
Should work, but if i'm not getting this wrong this will also not let you run auto customizations
Click to expand...
Click to collapse
he din mention he did a hard rest. :S....sometimes it may ask for allignment all of a sudden....my x1 did once
but if he has already done a hard rest then he has to wait 10min....should work or he could use the app (whose name i 4got ) to go into reg and delete the reg that triggers customization
PS: ill give more details when i get home n check out the app n the reg

tried to delete as you instructed.
Unfortunately he tells that I "cannot delete file welcome: access is denied"
any way to overcame it? tried also to rename or move, but with no avail

tecmobility said:
tried to delete as you instructed.
Unfortunately he tells that I "cannot delete file welcome: access is denied"
any way to overcame it? tried also to rename or move, but with no avail
Click to expand...
Click to collapse
I had the same issue tried even deleting files via third party applications and skipping align screen but once u do it your screen doesn't react for any thing you do. you cannot configure neither ur buttons too sometimes doesnt work. the best way which I found that you try any of the original ROM version ..either UK or NAM which actually resets the radio and brings back in normal stage...hope it works for you.. then you may tryu doing hard SPL and install any of the cooked rom.

I have installed indeed the uK offical version...