vibe then ring - Tilt, TyTN II, MDA Vario III General

Under phone settings you can set "vibe then ring" as a ring type. Doesnt work...how come?

probably because of the ringtone delay.

What ringtone delay? I know there's a delay if you pick a MIDI, MP3, or WMA file. Only WAV files play immediately. But this shouldn't affect vibration.

Vibe Then Ring works fine on my AT&T tilt with Stock ROM, using an MP3 as the ringtone.

Related

Problem changing Ringtone

This is driving me mad! For the life of me my Kaiser won't let me change the phone's ringtone from the standard. When I open an MP3 in audiomanager then choose set as ringtone, I get the error message "there was an error copying the ring tone to \my documents\ my ringtones. The ringtone could not be set. Please verify you have enough room on your device and try again", i've even tried manually copying mp3's to the \my ringtones directory, I can view them but they don't play in the ringtone selection screen (they play OK in audiomanager), even if I select a different mp3 in the sounds and notifications screen and select OK, my kaiser defaults automatically back to the standard ringtone. Oh, there's loads of space free as well - about 47mb.
Any ideas?
mp3 extension
Did you change the program for the .mp3 extension?
I noticed the same behaviour when I assigned the mp3 extensions to MortPlayer:
my ringtone would revert back to the default and choosing the mp3 ringtone wouldn't work.
After unchecking the mp3 extension within MortPlayer, I could choose a mp3 ringtone again.
Thanks a lot dude - will give this a go.

Two questions on ring tone

I have 2 questions:
1)I've note that for apply the ring tone for the calls, the format must be only mp3, instead for the notification the format must be only wav. Is there a program that resolve this problem? I would apply an mp3 file for the notification and a wav file for the ring tone. moreover when i choice vibrate and ring, the vibration work continuosly, in other cel the vibration work at regular interval. What i resolve this problem?
2)The volume of ring tone are very low, but i up his at max. Is there an registry or file hack for increase the volume?
Thanks for the attention
I would be intrested to know the answer to this also, it would be worth having the sound increased if possible. at the moment i am having to normalise the mp3 in a sound editing program before sending to the phone.
Sean
2) For ring tones, are you using mp3's that you ripped from another source?
If so, can you compare the volume of these mp3's to built-in ringtones, such as "Capri?"
I ask b/c I find the volume of my Tilt to be very satisfactory; In fact, when using Capri ringtone I usually turn it down a little b/c it is very loud.
Usually when I rip mp3's, though, they turn out at a much lower volume than the included ringtones and I use Audacity (a free audio editor) to bumb up the db of the mp3.
If there is a volume hack, it will likely be system wide which may have unwanted side effects.
Hope this helps some.

Ringtone stops then continues...

Hi all,
I've got a Diamond with a wav ringtone.
When the phone rings, the ringtone starts, then stops for about 1/4 second then continues to play correctly...
The file is stored on the in the My Device / My Documents folder.
The file is about 2.5MB.
The file plays correctly when using media player and when previewing the ringtone in the notifications setup.
Any idea how to get it to play correctly when I receive a call instead of the slight stutter / pause?

Song As My RingTone

Hi all,i wanna set my song as the ringtone for my Diamond....
anyone know how?do i need a software?
thanks
Music will ring up to 30 sec. Use program on Diamond to extract from music on phone, or copy your own to Ringtones in My Device, then Settings to select your ringtones.
Go to the chosen music by explorer, press until it appears “define like ring tone” and that is all.
got it....thanks....

ringtone bug of wm 6.5.x or just of mightyrom impact?

been using mightyrom impact for a while. the os is wm 6.5.3.
i find that mp3 or wma ringtones for incoming calls work just fine until you launch wmplayer. once the wmplayer is launched, any mp3 or wma ringtones for incoming calls fail to work.
If you go to phone-menu-option-sounds, you'll find that when a wma file is selected, it shows "the file is either interrupted or unavailable"; when an mp3 file is select, it plays no sound...
the only way to make them work again is to do a soft reset.
those problem will not happen if you choose a wav file.
what's more, the htcvolumecontrol.dll is updated to 2.1.1922, the former version built in the previous taskbar.cab fail to work. when you press the volume keys, all you get is the original ugly control interface.
bugs also take place when using G-Alarm. it makes no sound when wmplayer is launched.

Categories

Resources