Related
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
is this housing http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260453968402&ssPageName=ADME:X:RTQ:US:1123 a FURTHER rip-off in quality as the OEM found here http://cgi.ebay.com/OEM-SONY-ERICSS...ries?hash=item2ea6dd8d1e&_trksid=p3286.c0.m14
i want to buy a new housing but i don't wanna buy one with less quality than the original
what are your thoughts on the pics there?
Judging by the pics both fascias seem identical. Although don't know why this big pricing difference. Maybe the first auction is for a replica housing? Don't have large pics as the second auction so we can tell for sure.
Also, at CNN http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html the housings are pricey. For me go for the second auction or buy from CNN, you will be 100% sure that the housing is the OEM.
yeah i was looking at the $24.00 on ebay too... someone should buy it and tell me how it is
i think im gonna let this pass and sell my x1 as it is, im thinking of leaning towards the touch diamond 2 i will miss my keyboard but what the heck
Yo!
I ordered the $24.00 last week... When I receive the housing parts, I will take pictures and spread the message....
Fingers crossed......
Damn the cracks....Its a pity to sacrifice a gd device just now that some gd new things are coming....senseUI....Leo...sure it'll come for d2 too.....but no KeyBoard there.....I have ur very same problem...but I'll try the case !!
Received the housings yesterday.
They're certainly not OEM (maybe the backcover is, the rest not). The outside looks quite nice finished, the set is quite complete (with some tools for the fitting). From the two sets I ordered, one has a large gluestain on the top part of the housing (below the LCD). This gluestain damaged the paint. So I decided to start transferring the phone in the other housing.
After dissecting the phone I started with the assembly of the screen part. The speaker fitted not quite nice, so took some feddling to get mounted. At last it fitted (the print on top of the speaker fitted just). Closing the top part of the housing was a mess. The snap-locks didn't snap (partly) and on one side the housing did not flush fit. The (original) screws did not fit in the thread bushings.... With some fiddling I sort of managed to fit them. Then on with the bottom part. The new chrome buttons do not fit in the new chrome housing part.......
This is were I give up for yesterday. I think I'm going to rebuild the old housing en give up on the new one....
So.....
Decide for yourself if it's worth the trouble.... The housing looks quit neat (not as good as OEM though) but the fitment process is quite troublesome. Delivery was fast and the package is complete (including self-adhesive rubber for screen and speaker fitment). I will get in touch with the guy from Ebay with my findings.... Maybe I'm doing something wrong....
Will post some pictures tomorrow or something....
thnx ur comments were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx, ur comment were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx dude, im waiting on mine to be delivered,
looking forward for more reactions...
@Fliptil
From a scale from 0-10, how hard was it to do?
Before starting myself, I want to know if i'm capable of doing this.
To be honest, I know how to fix stuff, but don't know if I can do this trick..
Thanks for sharing anyway
Does anybody know, where i can buy a non branded battery cover for my sliver x1?
It is branded with T-Mobile, but i would like to have it blank or non-branded.
An original one is 25 € in ebay Germany. That's too much. So a cheap one would be fine.
Thanks in advice for all tips!
Best regards
Jog
ebay dude, i purchased one 2 weeks ago for about 10 GBP
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170363212269
OK guys....
I managed to revive the Xperia tonight.... It has become a hybrid with the metal (original) front and black backside. The middle part is also left original. So the only part I ended up exchanging has been the back cover.
First of all; kudo's to HTC for making the Xperia somewhat sturdy (at least the inside is...). The amount of mechanical havoc tha has been put through the innards of the phone are substantial... And still everything functions!!
After the initial assembly attempt a few weeks ago, I was sure that I had wrecked my phone trying to assemble it with the new housing. Some parts did not fit really well, and the (original) screws did not quite fit the (new) threaded bushings. Halfway through the assembly process I ran into the new chrome buttons not fitting in the new chrome middle part and I gave up on assembly for the time being. After recharging myself for a couple of weeks I forced myself to take up the task of finishing the assembly of the phone tonight...
First I had to disassemble the phone (I was halfway assembling it...) again. I decided to use the original front (had some scratch damage and a very small crack) to surpass the not-fitting thread bushings in the new part. This was a problem... One of the screws had settled in the not-fitting thread bushing and decided to not unscrew, but turn the bushing in the plastic instead. After trying careful and not damaging anything for some time I decided it was time for the hobby knife and screwdriver (as crowbar...). The new front cover did not survive this operation. The screw and the innards of the phone did however!! Reassembly using the old front cover was quite easy, as was reassembly of the back using the original middle part. In the new back part was the thread bushing missing for fixation of the speaker... I used the not-fitting bushing from the front cover as bushing for the speaker fixation. Off course after I made the bushing fitting by forcing the screw in the bushing using a sturdy screwdriver and a set of pliers. This bushing was hammered (carefully...) into the location where the bushing should have been.... This sort of worked. The new back cover does not fit as neat into the original middle part as the original back cover, but it did fit (with some force). The plastic lip that fixes the SIM card was a bit to long, so I had to cut of 0,5mm to make it fit the SIM card. And last but not least only one of the two new battery covers was able to get a grip on the phone...
Then came the thrilling moment to switch on the phone.... Everything worked as if nothing had happened!! So end good all good; I have a phone that looks quite neat (part brushed metal - part black) and functions.
If it was worth the hassle... I doubt it... When you've got a phone that is in pieces and you want spare parts to repair it (as cheap as possible and you like some hobbying) then go ahead and buy this housing. If you want a phone that looks as good as new (and you don't want to risk a heart attack or nervous break down) then I guess you're better off leaving this housing as it is.... For a phone that's worth a few hundred bucks I think this housing is not OK. For a scrapheap phone that needs revitalisation for a small amount of money than it's OK.... If I had to do it all again I think I would have gone for an OEM housing.... After all, I'm happy that my phone functions again so I can leave the TYTN at home. I was to stubborn to buy another housing...
This has become quite a story, hope it will be of any help to somebody. Now I must see if I can post some images....
Grreetz,
Ronald
Some pictures.... try if it works....
Hmm i've dropped my poor x1 on the concrete sidewalk as i got out of my car.
Amazingly it must be good quality because there are a only a couple of scratches on the front and some damage on the rubber around where the
stylus is, but otherwise everything works and is functional.
What this experience did, was got me lookin for spare parts in case I'd
ever need them. As a result I ordered from the same person on eBay 2 days ago
and I just now found this post. Needless to say, I'm damn scared that I've
wasted the money. You tried to fit the black parts on a silver X1, and mine is black,
so I'm crossing my fingers that for some unknown odd fantastical reason, it fits better on the black version. Also may ask whether your model is an x1i or x1a?
I'm guessing b/c its silver its an x1i but u can nvr be to sure. As for me, mine is
a black x1a. I'll post back if i have any updates.
Hi Nick.
I've got a X1i, as you had already guessed.... The mixing of the parts is also a bit of a risk.... The chrome middle part (original) has suffered some damages during my disassembly actions to start with... And has developed some new cracks in the use as a hybrid. Maybe I've overtightened some screws, or maybe the bottom part does not fit well enough so it develops to much tension I don't know...
I've decided to use the X1 till it dies, and to buy something else (no slide keyboard) a little bit more sturdy when it does. I am not going to do any repairwork on it. The design is simply flawed, I have had it repaired at SE once, when it came back it was broken again within two months. These stories can be found al over the internet, so I am not going to repair it again (just to get it broken again). I am not careful enough for a phone like this (however, my colleague also has a X1 that's broken and he is very careful...) I guess.
Just my two cents.
thanks fliptil I'll keep those things in mind.
Before i dropped my x1 for the first time. There was some kind of defect in the silver middle part. At first it was a slight crack so i thought nothing of it, until a piece fell right out of it. Until now i've never needed to go through the process
of getting something fixed and was my experience painful. I got mine through a carrier (Rogers) so I called them on the phone. I was on hold forever, and when I finally got through they told me I had to go to a rogers store to have someone
personally take a look at it.
I got to the store, got on their phone, and was on hold for 20 minutes. When I got through they told me they would connect me to a specific department.
Another 20 minute wait.
I got through and then gave the phone to a rogers employee there. He confirmed that it should be a defect as there were no signs of dropping it and then HE waited 20 minutes while the guy on the line called sony.
I waited all that time to find out that I cannot get it replaced through my carrier but had to go through sony themselves.
I looked up some stories of experiences with SE's services and found that most (if not all) of the time they replace your x1 with a refurbished one, and I wasn't about to trade a perfectly brand new one with a minor ding in it, for
one that could be potentially scratched up and badly treated.
Now that I've dropped it though I fear that whether the defect gets worse or not I cannot get Sony's warranty on it. However, after what you've just told me I don't think I want to. Here's to hoping that i won't have to do x1
surgery anytime soon...
Hi,
Last night I knocked a small table and my girlfriends phone and a remote for the TV fell off.
We noticed that her phone now has a ring of black dots on the screen, mostly visible with a white background (E.G websites) but also from the home screen and the like.
We think she's cancelled her phone insurance, as she's never had a payment out to the company.
Can anyone tell me if its a Digitizer (What is one of these? Is it just the touch screen sensitive part of the phone?) Or the actual LCD Screen itself?
If you click on the photo it will load a larger image
Thanks for any assistance, kinda annoyed about this and wondering if I can repair myself with the parts on ebay. Or does anyone know how much HTC Charge to repair similar? Either in $USD, £GBP or €Eur, I can convert and get a ball park figure.
Hi
First of all is the phone still in warranty? If so take it back to an HTC dealer they should repair it for you for free. TD2 screens are not very good and it's a common fault. ( i had to have mine repaired after just only 3 weeks! )
The TD2 screen is made out of 2 parts, The touch screen or the 'digitizer' as you call it and a normal LCD screen underneath. You need to establish which has gone faulty.
If the touch screen still operates normally i.e the screen does not lock up or freeze and allows you to navigate normally then its the lcd screen below. If the touch screen is faulty one good way of checking is to put a piece of tape over the damaged area and try to lift it up a little to see if the marks / dots disappear and functionality can temporarily be restored.
Its hard to tell from your picture which it is..... sorry
I'm not sure how much a replacement by a dealer would cost, but i'm sure you can replace either yourself. ebay is a good place to look
Hope this helps.
I've had a reply from HTC UK who said the following:
That looks like there are a bunch of very small cracks in the screen. the black stuff is likely the Liquid Crystal from inside the display that has leaked out. If the dots get larger then it would definitely seem that the screen has got some cracks in it.
if this is the case, the standard charge for replacing the LCD is around £180 as sadly it is all one complete unit on the diamond 2, so it is not just the LCD underneath that needs to be replaced, but the whole screen assembly including the touchscreen layer and the actual LCD.
I hope this information helps you to make up your mind.
best regards,
Pete W
HTC
Click to expand...
Click to collapse
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Hi mate,
had the same problem...
the item you psetd from ebay is not the one you need to change.
you need a digitizer, not an lcd screen.
i got one from ebay (http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItemVersion&item=290376721935&view=all&tid=393718237019), it includes both the lcd and the digitizer, you can check ebay to find other auctions offering the digitizer only.
you can change the digitizer on your own if you don't mind loosing the waranty of your phone.
cheers
Hi,
I had already found this: http://cgi.ebay.co.uk/Touch-Screen-...UK_Mobiles_Accessories_RL?hash=item5882e7ef74
Will buy in a bit, funds are a bit short today.
The Touch Screen's functionality hasn't changed at all though, no sticking buttons or anything. So I suspect that its the LCD Screen thats damaged but will follow you're advise as you're going to have more experiance than me (and its the cheaper part to begin with!)
Scrap the above post.. my g/f has just told me that the dots on her phone are bigger/worse. Looks like its the LCD Screen afterall
i still believe it is not the LCD.
the digitizer is actually sitted on a glass, and the LCD is below that. it is very difficult to harm the LCD. i also though it was the LCD (at least i wasn't sure which was broken) so i ordered both of them.
if you disasseble the phone you will be sure if it is the LCD or not.
i vote for the digitizer
good luck, if you need any help, i'll be pleased to help you..
Just to update, A few days after I posted and got helpful advice on here.. she called me up to say the dots have disappeared, and they have still gone now a few days after.
She said she put it in the office where she works, under a printer paper tray, and the office was warm. Something has (maybe only temporarily) fixed it.
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Well F**K me! just bought a second hand diamond 2 to replace my xperia...
...seemed to work great checking it out... went home with the phone in my pocket... and as soon as I turn it on the touch screen doesn't work
dissected the whole phone only to discover the digitizer is glued to the bezel!
I ordered this from Ebay, will update if I got it working with the brand new housing + digitizer: http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=380166349182&ssPageName=STRK:MEWNX:IT
fingeres crossed
Please report back here on this thread if it works
fluke said:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Can any one help with this matter?
fluke said:
Can any one help with this matter?
Click to expand...
Click to collapse
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
jodeltje said:
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
Click to expand...
Click to collapse
Thanks for the reply as I said previously:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Also the LCD didn´t had any marks at all, but i´m going to buy the TS+LCD and replaced by parts first the lcd because it´s a lot easier to replace then if the problem persists the TS.
I will post the result later when i get the parts to replace.
Superman_1122 said:
I've had a reply from HTC UK who said the following:
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Click to expand...
Click to collapse
Can anyone confirm the above link as being both Lcd and Digitizer? I'm sure it doesn't mention it in the listing but the picture looks like it's showing both connectors.
Most likely only the LCD that's my conclusion if you look at the sellers store.
But to be sure e-mail the seller and ask.
http://stores.shop.ebay.co.uk/Elect...QQ_sidZ195653022?_nkw=diamond+2&submit=Search
Soooooo, as I've already posted here, My digitizer was busted on the phone I just bought... what I didn't tell was that I ordered a digitizer, then checked if I could remove it easily...came to the conclusion that I couldn't... and ordered a digitizer+housing so I could easily fit it on.
the mail brought me the digitizer today, and while knowing a better solution was on it's way I couldn't resist and try if I could make it work.
Turns out it super easy to seperate the digitizer from the bezel using a hairdryer (softening the glue) and a knife:
Take your phone apart, just the 4 screws, click the plastic center off it. Remove the digitizer cable, the touchscreen cable and the speaker cable.
now you are able to remove the green plate which holds all chips and stuff.
underneath that is the screen, lift it up gently going under it from the gap the removal of volume buttons leaves, put it away safely.
Now remove the speaker, the buttons under the zoom bar, and the power button(don't forget the the power button, and rubbery thingy that falls out of the bottom, the hole needs to be at the bottom when putting it back in).
your phone should be completely empty by now... just the front and the digitize glued together.
make the front of the phone reaaaaaaaaaallllly hot, put the knive between the metal and the digitizer (I started at the part where the zoombar is) and gently push it between the two parts... (from the inside of the phone to the oudside). Now just keep the whole thing above the dryer to keep it warm and slowly slice your way around the phone (no secret wires are there that you can cut through).
I used some random glue I had lying around to glue the front back to the new digitizer... perfect!
so the screen is like new now
ps bought this digitizer: http://cgi.ebay.nl/Touch-Screen-Dig...wItemQQptZPDA_Accessories?hash=item45eed6effc
Thanks for that jodeltje.
It sounds exactly the same as when i replaced the digitizer on an Omnia. Really not as hard as one might imagine. Taking your time and being careful are the most important things.
Hey guys,
I came into same boat last night.
Dropped my T-Mobile MDA Compact V from 2.5ft table, Backwards (Not towards LCD) and now it has black dots on screen. I guess the LCD has pressed backwards by chip sets.
Here is a screenshot.
I think its LCD damaged but I don't have cash to replace nor device warranty.
Do you think the problem solves eventually? Coz once I had dropped sony mobile and it too had same issue but solved after many days.
Hopefully it solves.
BTW; does LCD affixed to Digitizer? by seeing service manual, it doesn't look like it is. And I afraid to get cheap hongkong LCD screens for about 30$ since they won't be true quality display. i.e blueish.
Thanks...
Best Regards
hello CRACING,
sorry about what happened to you...
from the picture i can say that you have a problem with the digitizer...
your LCD is ok.
i tend to have this problem over and over again the last 1,5 years... i replace the digitizer (or the glass on which the digitizer is attached to) every 3-4 months..
yes the ones you get from ebay are not that good quiality, but well it keeps the phone working...
if you need assistance on replacing the digitizer, i can help you, by providing pictures and istructions...
cheers
Hi to all,
Before you ask, yes!, I did use the search and found some related posts to my issue, but a little outdated and I read so many things that I think I'm more confused.
My HD2 works without problems with the broken screen...but unless i have tape on it, i I'll cut my fingers...so after almost a year i decided it's time to repair it!
For that, I WANT to buy an LCD+Digitizer Glass Replacement (because i hear some are made of plastic). Because there are at least 3 different versions (so i heard) of HD2 LCD and hundreds of listings on ebay, I'm afraid to buy the wrong part.
Correct me if I'm mistaken:
There are 2 types of connection, solder or socket type. Mine is definitely socket (60H00300), correct?
Every socket version (60H00300) is the one that the LCD is better, right?
If i purchase any LCD+Digitizer combo that states as "for HD2 T-Mobile T8585 solderless/version 2/socket" will it be ok? Even without the T-Mobile logo on top? ...I ask this because I know for a fact that the US T-Mobile version has a slightly larger screen/digitizer!
Plus, I would also appreciate if someone pointed out an original screen replacement (meaning scratch resistance glass digitizer) that i could buy with confidence! :highfive:
Here's my sad HD2...i had to put tape on it, or the top right corner would fall in pieces..
Your TMOUS LCD & Digitizer is 100% same size as any other model HD2.
size difference is in the casing below the buttons & is about 1.5mm to allow for different antenna setup on mainboard.
Any 300 type will fit & work fine but you are indeed correct in assuming issues on quality & materials used.
Buying complete LCD/Digitizer does not mean you will get better quality parts & to be honest it maybe worse as the quality of tape used on some of these is poor.
If your LCD is fine I would make the effort to remove the Digitizer & thus just replace digitizer.
Can be done by warming it up with a quality hair-dryer & using a few new razor blades to loosen the bond, time & care is the key here.
Tapes for rebuild can be found on eBay from poland with worldwide shipping.
Digitizer for TMOUS is this one:
http://www.ebay.co.uk/itm/230897875502?
You would be advised to use a film on lens as even the glass ones can scratch as not as hard as original.
Trying to find original is a pain & high cost for possibly no gain ...
Most important part is learning good repair steps & using good care when stripping & rebuilding as without that a good or poor quality digitizer will be just as useful as a beer mat.
Mister B said:
Your TMOUS LCD & Digitizer is 100% same size as any other model HD2.
size difference is in the casing below the buttons & is about 1.5mm to allow for different antenna setup on mainboard.
Any 300 type will fit & work fine but you are indeed correct in assuming issues on quality & materials used.
Buying complete LCD/Digitizer does not mean you will get better quality parts & to be honest it maybe worse as the quality of tape used on some of these is poor.
If your LCD is fine I would make the effort to remove the Digitizer & thus just replace digitizer.
Can be done by warming it up with a quality hair-dryer & using a few new razor blades to loosen the bond, time & care is the key here.
Tapes for rebuild can be found on eBay from poland with worldwide shipping.
Digitizer for TMOUS is this one:
http://www.ebay.co.uk/itm/230897875502?
You would be advised to use a film on lens as even the glass ones can scratch as not as hard as original.
Trying to find original is a pain & high cost for possibly no gain ...
Most important part is learning good repair steps & using good care when stripping & rebuilding as without that a good or poor quality digitizer will be just as useful as a beer mat.
Click to expand...
Click to collapse
The main reason for me to buy the LCD+Digitizer is that i cant afford to be without my HD2 for more than a couple of days...and if I mess up ending the relationship between the LCD and its digitizer....I may end up with two (or three) broken "hearts"!
I'll risk in buying an LCD+Glass Digitizer "300 type" (+film protector) and then attempt to recover the original LCD for a "future repair" as you suggest!
Thank you for your reply, it really answered my issues! (I pushed the thanks button...but for some unknown reason to me it didn't work )
Shwanz said:
The main reason for me to buy the LCD+Digitizer is that i cant afford to be without my HD2 for more than a couple of days...and if I mess up ending the relationship between the LCD and its digitizer....I may end up with two (or three) broken "hearts"!
I'll risk in buying an LCD+Glass Digitizer "300 type" (+film protector) and then attempt to recover the original LCD for a "future repair" as you suggest!
Thank you for your reply, it really answered my issues! (I pushed the thanks button...but for some unknown reason to me it didn't work )
Click to expand...
Click to collapse
Good luck, hope it works out fine ...
hi
my display was broken, but have worked for a year or so.
now it is frozen/ unresponsive and i have purchased a full display.
just found a very easy way to replace the whole display in just 3 minutes by accessing it from the front side..
i am not yet allowed to post the link, but if you google this
IMPEXTROM CAMBIAR TROCAR DISPLAY HTC HD2
you will see the 3 minutes video
but it seems too easy to be possible ...
any hints?
thanx &cheers
That been set up for the video as you can see it been off before & the chassis the lcd is bonded to is clean of all bonding tape :-/
Also original has signal interference tape runing down sides across all 3 layers.
also if you heat the front first thing to seperate is the digi from LCD as the lcd to mid chassis is a strong bond.
Best way is popping them out of rear cover, fitting a pre built lcd/digitizer is not hard, just use quality adhesive to hold lcd to centre chassis & buy pre cut black foam tape for the top & bottom digi glass edges or rebuild is next to pointless without this done well.
I've done a good 30 odd HD2 screen & mainboards & no way I could do it to my standard via that video.
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
gunemalli said:
I'm in the same boat as you. Dropped my G2 while getting off pickup truck and the digitizer is kaput. I have no touch response anywhere on the screen. But the LCD is working really well. No damages to that.
So i'm looking for a digitizer as well to replace it.
Click to expand...
Click to collapse
i am looking for the LCD and digitizer assembly. but i am trying to find OEM part
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
housing is not an issue
Lttlwing16 said:
When my wife broke the digitizer on her n4, I was in the same boat. I searched earnestly for TRUE OEM parts. What I discovered was this site:
http://www.etradesupply.com/catalogsearch/result/?q=LG+VS980
They are the most expensive, but to my knowledge it is TRUE OEM.
Due to time constraints, I ended up getting a screen on Amazon that claimed to be OEM, and while the screen and digitizer assembly I could tell were brand new OEM parts, the housing had been recycled, as it was missing some adhesive for the board components. While her screen works fine now, it lacked the filter for the led notifications light (as it was a recycled housing) and was more difficult to replace due to the fact I had to conserve the adhesive film off the old housing and transfer it to the new housing. If I had to do it again, I would pay the extra and get the TRUE OEM brand new from etradesupply.com
Good Luck!
PS. If you need a good youtube video for the repair, I recommend this guy: https://www.youtube.com/user/LE55ONS
Click to expand...
Click to collapse
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
i bought one
squee666 said:
I bought from ebay one of the ones claimed to be an origiginal oem screen. Works perfect and do blemishes etc.
Click to expand...
Click to collapse
i did buy one from ebay today, after been an annoying person with lots of questions hahaha. i refused to buy from anyone below 99% profile credential on ebay. here are the questions i asked lol
Is the LCD screen manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store? if not, is the same Quality, TRUE IPS LCD with Gorilla Glass 2 digitizer?
Is this LCD part brand new or refurbished from reclaimed old parts?
Digitizer – Is the Touch Panel manufactured by the same company that I would find on brand new in box phone that I purchased from an authorized store?
Digitizer – Is the Touch Panel new or refurbished, or reclaimed from old parts?
and if I bought a brand new in box sealed G2 from LG, the part I’m asking about would be 100% identical with no differences in quality or condition?
does it work on D800 model, if not do you have one that works with D800 that is a genuine OEM?
is it OEM (Original equipment manufacturer), does it have part number on the flex cable, and LG display co,ltd label ?
only one seller, answered all of them concisely, without political correctness or avoidance. lots of them stopped talking to me, and some only answered vaguely. i had one hilarious response, who said the the screen is OEM but not genuine, i insisted for him to elaborate, he said OEM but not original. all of us know that OEM stands for Original equipment manufacturer. i sent him a response, that it does not make sense to be OEM but not original. he replied back OEM for them is, Optical equipment manufacturer lol, heck i do not even know what does that mean lol. i took a screenshot of the definition and sent it to him, he never replied back hahaha. many shady seller on ebay
P.s once i receive the part and install it, i will update on the condition/quality
can post the link for the seller you bought the assembly?
thank you!
Link
noris08 said:
can post the link for the seller you bought the assembly?
thank you!
Click to expand...
Click to collapse
http://www.ebay.com/itm/251591046010?_trksid=p2060778.m2749.l2649&ssPageName=STRK:MEBIDX:IT
working
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
sdcaliber said:
update,
as i provided previously with the link of the LCD/Digitizer, i promised to update after purchase and assembly.
i self repaired myself, took me about an hour and Half give or take. it works like a charm, no problem whats so ever.
advise, before attempting to do it yourself, find a youtube video of how to disassemble and reassemble, including how to apply the adhesive (took most of the time).
i can confirm, and take my words for it, the one i bought is an OEM LCD digitizer.
cheers,
Click to expand...
Click to collapse
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
jamracer said:
Can you provide any info on how u got the screen to securely cit in the frame, like what adhesive did u use and how u did it?
I did the repair my self the phone works great except the bottom ov the screen, sticks out abit n I can see the back light, very annoying
Click to expand...
Click to collapse
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
sdcaliber said:
absolutely,
keep in mind the following things,
i used 3mm double sided adhesive tape, you can find them on ebay for 2 dollars give or take. the hard part laying out the tape in correct manner. you have TWO WAYS to do it that i know of using the tape, whatever that suits you. first one, most people will place the tape on the housing (if you did that, avoid placing the tape over the proximity sensor, camera, the usb, and the connection ports. or it will be a pain to remove them and damage maybe imminent in such situation ). the trick part, is the tape in vertical position around the edges where the bezels of the screen will sit (if its done incorrectly, you will have the problem you have described). therefore i will share the second method, my method :
check if the screen and digitizer works correctly before finally putting the adhesive;
WARNING: if you are not sure what you are doing, please consult with phone technicians for a professional fix. this is only my method/my opinion and in no way constitute a professional advise.
it is separated in to three parts
1 - use 3mm tape to tape the bottom and top of the housing, i repeat do not tape, the proximity sensor, camera, the ports, or the usb, use common sense or youtube to see which one is which .
2 - use the 3mm tape and tape the edges behind of the screen under the bezel (on the screen/digitzer assembly itself, not the housing). it is a narrow spot to tape, that where most people end up with popping out screen at the bottom edges and seeing the light. due to the narrow edges, use a small tweezers to place it.
3- use the 3mm tape and tape the edges of the housing where the bottom of the screen will sit (optional). in my case, i did that also
now peel the double sides 3mm tape, using tweezers will make it easier, much much easier.
once done, take your screen/digitizer assembly, and insert the bottom flex cables first into the housing (they are two cables, be careful, they are fragile), make sure the bottom part sit perfectly and all the cables are sitting correctly into the housing, before you insert the top flex cable (longer thinner cable).
insert the flex cable (the top one, into the housing slowly, while checking around with your eyes, that everything is aligned with the housing. once the flex cable in, double check and see if the flex cable is seated perfectly. check around the phone edges, and if everything is perfect, press gently on the edges, until the adhesive makes contacts. if you find that the screen is not sitting correctly, gently lift the phone slowly, and position it correctly before the adhesive sticks (takes about two minutes before the adhesive taking effects, keep that window in mind).
after the everything is sitting where it suppose to, place everything back inside the phone, turn it on and check again if its working along with the digitizer (i recommend checking whether the screen and digitzier works before placing the adhesive). once you check everything is working fine, turn the phone off, and unplug the battery cable from the motherboard.
use hair dryer (on low) or heat gun (use low temperature), hair dryer is safer if you are not sure what temperature to use with the heat gun and heat around the edges of the screen (keep it moving and do not stay in one place) this is for the final seal, about 30 to 40 seconds of heating. now the screen is sealed shut. leave the phone to cool down for a minute (optional: use a rubber band around the top and bottom for added pressure, not too tight though). plug the battery cable in and reassemble the phone.
cheers
Click to expand...
Click to collapse
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
jamracer said:
thanks alot of the info,
i did the repair and all, the screen and digitizer works well, its just the bottom of the screen sticks up, i went ahead n ordered a roll of 3m 300lse double side tape, the dounble side tape i hav is just the regular black tape, dont think its strong enough, i will go over everything with a fine tooth comb when it arrives, i hav a sprint g2 on its way as well, do u know if the d800 and the ls980 frame is compatible??
thanks for the info really detailed
Click to expand...
Click to collapse
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
sshark said:
I bought EB40 battery for Atrix HD through Etradesupply's Amazon store. I haven't had any issues with battery and lasted as promised.
Whole purpose of that project was to put battery from Droid Maxx into Moto Atrix HD and bump up capacity from 2100mah to 3300 mah.
May be different buyers have different experience or I just got lucky.
Click to expand...
Click to collapse
yeah maybe, all depends of course. most of these products are subject to opinions if there is doubt about their OEM legitimacy. but for me, i will not buy non OEM for battery again, it scares the hell out of me. let's say i had a horrible experience before. i had Note 3, and bought a battery for it. the extra capacity made me drools lol, so i went with it. days later, i found the phone in total meltdown, literally. woke up from my sleep, and the phone is melting/fire.... scary scary experience. the good thing, i do not sleep while my phone next to me. it was on my table, charging.
side not: the original battery of Note 3 malfunctioned
OEM
sdcaliber said:
lots of ebay products claims to be OEM, but i smell knock off (aftermarket). my guts tells me i will regret buying from most of the obeyers who claims OEM/new .. of course their prices are tempting, for example most of them offering a range from $63 - $69..
if you bought a screen, let me know where did you buy it from, and how good it is?
what do you recommend, such as going after used ones that are pulled from previous one etc?
thanks
Click to expand...
Click to collapse
I bought it on Ebay and now it´s working fine, nice!!.. First I bought only the digitizer and it was faulting, but now this assembly is really working fine:
http://www.ebay.com/itm/281280382756?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Regards,
Just posting to share my experience. I bought a replacement lcd\digitizer for my G2. Once installed, i had white lines going up and down the screen.
Some devices use different panel hardware (JDI instead of LGIT) and you will have white lines after using patched kernel. You must use those kernel with "_jdi" in its name. More info:http://forum.xda-developers.com/show...&postcount=122
After flashing the new kernal the phone works great. The phone does get noticeably hotter, unfortunately, which is a little worrisome.
The kernal issue and the heat lead me to believe that what i bought was not oem.
Sent from my LG-D801 using XDA Premium 4 mobile app
Is D800 frame compatible with LS980?
sdcaliber said:
3m 300lse double side tape should be fine, as long as you use it correctly.
in regards to the frame, well that i am not sure about it. however, the LCD/digitizer i ordered was labeled OEM LS980 (sprint) VS980 (Verizon) and compatible with D800 (att- that is mine) and D801. so far, it fits perfectly. make sure it is OEM, if its not, the cut maybe off, that results discrepancy in fitting with the frame. also, double check with the seller, if the its compatible with your phone.
cheers
Click to expand...
Click to collapse
I was just working on a frame lcd assembly swap on an LS980 rev 1. The frame I bought was a Verizon LV980 and the vibrator was off buy at least 3mm, I didn't mind losing the vibrator to gain a good lcd. Then the proximity detector layout was different, the LS980 had an extra piece that fit in a hole, but it could be removed. About 5mm below that is a ground connector for the motherboard on the LS980 but not on the VS980 and the tab holding the antenna coax hit the motherboard making the frame about 0.5mm too small causing the mobo not to seat.
All of these could be amended. Shave 0.5mm of the soft metal chassis, very easy, mobo grounds in at least six other places and proximity sensor had a removable tab.
But the bottom of the chassis where the dock port/usb board sits was just too different, the LS980 daughterboard wouldn't seat, it was larger. It could be forced but only at an angle that made the usb port off-center and not parallel to the opening. My repair stopped and re-assembled the phone with the LS980 chassis complete with my damaged lcd.
-----attached pics of proximity sensor, and ground connector area, didn't take more, I was getting mad.
sdcaliber said:
i looked at etradesupply, but i searched on google on them and there are many allegation they are not OEM, and their delivery time/shipping are not something you want to deal with. been said that, i am only looking for LCD and digitizer assembly as i can assemble them into the housing myself, i have already took apart the older screen out of the housing without a problem.
Click to expand...
Click to collapse
Actually I bought an LCD from this company. I am very happy with it. It is true HD and the it was shipped for me in 3 days as they said. At first I was very worried with the comments but I took the risk and I am satisfied with it. I don't know why others complain about it but I recommend them.