Turn the screen without sliding the keyboard - Tilt, TyTN II, MDA Vario III General

I have my TYTN II for a couple of days know, it replaced my good old MDA Vario.
I'm not really having problems, but there is one thing I can't find.
So here is my question:
Is there a little utility that wil turn the screen from portrait to landscape and back, without sliding the keyboard?
I used battery status on the Vario, but I'm afraid to try this because of the different processor in the TYTN II
any help is welcome

There is an icon that looks like ur phone with a stylus ....if u push that itll flip the screen to landscape.

I'm pretty sure that it wont matter...typically when you install software for your device you are installing it for a particular OS...not specifically for the processor (just like a PC). Obviously, if you are trying to overclock then this will be a different story.

Related

PDA2k Dead Touchscreen

Hello folks: sad day...
My PDA2k's screen started to not respond to touch all of a sudden. I tried a soft reset, and then a hard reset. This does not fix it. Of course, now I am stuck at the Windows Mobile start screen (the one that says "tap your screen to set up your Pocket PC"), and of course I cannot make it any further than that.
Any help you can think of? I am trying to get a hold of imate tech support, but the prospect of having to send it away for repair is really frightening.
Thanks in advance for any advice.
Fernando
i have the exact same problem now..
please help??????
did u manage to fix it?
Pockets of air under the screen protector and/or mis alignment of the screen protector can sometimes cause a touch screen to stop responding.
So if u have one applied, try taking it off to see if that fixes the problem.
tried that..not the case..still isnt working
Hay I have same problems litle diferents bat same.
Das anybody have idea vats happened. In my BA, half display doesn’t work (left) right side work.
Incense I perform hard reset system hold in tach scrin and cursor in right side work perfectly in left side work only
if I put pensile 5-6 sec. and again etc.System is that point hold and doesn’t work butscrin.
Thanks for your tips. My touch screen went dead on my BA over christmas. I was about to junk it until I peeled off the protector skin as suggested. Now it is working. Thanks mate
I got this problem yesteday, so i desided to try disassemble, my blue angel to check how deficult it would be to change the touch panel before i cheked the price on these panels. It showed to be a little hard to take it of, so i just assembled the "angel" agian, and miracules the touch now works fine, and I only adjusted the cable a little, but maybe this made the connection better. But on the hole I'm glad that I put it together agian before I bought a new panel.
Unfortunately I don't know exactly what did the trick. But it may be worthwhile to disassemble and try to make the cables sit a little better, and then just wish for the best outcome, of course if you are not sure how to disassemble divices like these do not do it, as it can make more damage to your blue angel, so even a professional technican can't save it.
suggestion
i had this problem but if you already back up your system in a sgt file on your pc then you can connect your BA with activesync and restore your system i don't know if you have backup file

Screen Align not working? DOA?

Hi, Just got my MDA Vario III, and it appears the screen alignment that WM runs on first boot will not work. By that I mean its asks me to align the screen, but it will not register the taps with the stylus or fingers.
However, it does know when I touch the screen as it brings it out of powersave. I downloaded this Remote Screen Alignment program, which is able to skip the screen align process, but then when I have done that the taps from the screen are all over the place - because the screen hasn't been aligned. The keyboad works fine for navigation around the menu's.
Does this sound like a DOA device? Or am I missing something stupid?
foaf said:
Hi, Just got my MDA Vario III, and it appears the screen alignment that WM runs on first boot will not work. By that I mean its asks me to align the screen, but it will not register the taps with the stylus or fingers.
However, it does know when I touch the screen as it brings it out of powersave. I downloaded this Remote Screen Alignment program, which is able to skip the screen align process, but then when I have done that the taps from the screen are all over the place - because the screen hasn't been aligned. The keyboad works fine for navigation around the menu's.
Does this sound like a DOA device? Or am I missing something stupid?
Click to expand...
Click to collapse
It might be a simple loose connection or something trapped between screen and bezel. But I would not be even thinking about that, it would be going straight back under warranty. Thankfully, this is not a common problem with the Kaiser and I think you have just been unlucky.
I assume you have not put on any screen protector that might be causing this behaviour> Otherwise it is a DOA and nothing you can/should do other than return.
Mike
Thanks. I hope its not common! No screen protector, but I did try one first before first boot. I immediately removed it when the taps weren't working. I'll send it back tomorrow, thanks.
Dont tap. Just lightly drag the end of the stylus around each target until it proceeds to the next one.
It's common and should be fine.
Thanks unwired. Whilst that does get a response from the TyTn II, and moves the align crosshair, unfortunately it just loops the alignment process indefinitely. Arranged an exchange with T-Mobile without a problem
foaf said:
Thanks unwired. Whilst that does get a response from the TyTn II, and moves the align crosshair, unfortunately it just loops the alignment process indefinitely. Arranged an exchange with T-Mobile without a problem
Click to expand...
Click to collapse
If the future device does it, just try what I suggested but be as accurate as you can.
Unwired's method works for me as well. My Kaiser always seems to lose the ability to detect stylus presses (but finger pressure works) every time I use it on a plane which I assume is due to the cabin pressure. When the screen is reset, everything goes back to normal. Has anyone else noticed this, or do I have some defect that is only going to get worse?
I got the second Kaiser, and it happened again. But I immediatley used unwireds method, this time being extremely precise and only moving the stylus slightly. It works fine now, and stylus accurancy seems to be ok.
I still think it's strange, as I have had an HTC XDA before and a tap was sufficient on the screen align process. Furthermore it clearly states "tap screen" not "tap and drag".
My last three Wm devices (Prophet, Hermes and Tytn 2) have all been reticent to respond to alignment taps... but carefully moving the stylus around the target has always fixed it.
unwired4 said:
My last three Wm devices (Prophet, Hermes and Tytn 2) have all been reticent to respond to alignment taps... but carefully moving the stylus around the target has always fixed it.
Click to expand...
Click to collapse
For me it is more like 'tap-and-hold'. I make a firm tap on the '+' symbol, then keep the stylus pressed on the screen for one second, then release. The '+' then moves to the next alignment point.
Just for the record, I think the problem is common!
I've seen many people who have unresponsive touchscreens, and now I'm one of those unlucky people. And nothing works. And I don't have warranty because I'm in a different country than the purchase country and the reseller here only services phone bought in the Middle East. #[email protected]$#@$#@

Kaiser Touch Screen not responding.

Hey guys I have flashed my Kaiser with a clean rom last night, everything went awesome, phoned work excellent just the way I wanted, and my hands were wet as the phone rang and now all of a sudden my Touch Screen doesnt work, nothing seems to be wrong with the phone itself, everything is still displayed on the screen.
Now I might need to send it back for repairs, but I reset to factory defaults couple min ago, and it says "Tap screen to begin" and I can't get any further?
Active sync or nothing works in that stage, how is it possible that I can flash my kaiser back to factory defaults if this is the case?
Isnt there a way of skipping that "Tap screen to begin" message?
Thanks a lot, any help is appreciated.
Gozzy69a said:
Hey guys I have flashed my Kaiser with a clean rom last night, everything went awesome, phoned work excellent just the way I wanted, and my hands were wet as the phone rang and now all of a sudden my Touch Screen doesnt work, nothing seems to be wrong with the phone itself, everything is still displayed on the screen.
Now I might need to send it back for repairs, but I reset to factory defaults couple min ago, and it says "Tap screen to begin" and I can't get any further?
Active sync or nothing works in that stage, how is it possible that I can flash my kaiser back to factory defaults if this is the case?
Isnt there a way of skipping that "Tap screen to begin" message?
Thanks a lot, any help is appreciated.
Click to expand...
Click to collapse
here you go:
http://forum.xda-developers.com/showthread.php?t=335568
Yo thanks man,
I have flashed my phone back to HTC's rom, touch screen still doesn't work, I can use the phone now again, I have skipped that process where it asks you to align the screen to begin with a program called Code Factory's Remote screen alignment (RSA)
Now I'm in Bahrain (middle east) at the moment, I bought the phone in South-Africa where I used to live, So I'm gonna have to use the phone for a while until I can send it in for repairs.
So just have one more problem, I can't seem to change the Main volume in the taskbar without using the touch screen, Is there any other way of changing the volume, coz I cant hear my phone when it rings at times.
Shot guys,
to adjust the volume, move the trackwheel up or down during a call, so you're gonna have to call someone.
as for vibrating, you've got me there
Man,that must be a pain that touch screen doesn't working.
Try googling MyMobiler, install on your PC, connect your PDA and it will autoinstall itself to your PDA too.
Run MyMobiler on the PC. Next thing you know you can control your PDA without even touching it at all ;-)
Cheers!
schizo said:
Man,that must be a pain that touch screen doesn't working.
Try googling MyMobiler, install on your PC, connect your PDA and it will autoinstall itself to your PDA too.
Run MyMobiler on the PC. Next thing you know you can control your PDA without even touching it at all ;-)
Cheers!
Click to expand...
Click to collapse
or get mDesktop form the net - it will give you remote desktop capabilities to your PDA + much more ....
yo guys, just wanna let u guys know, the problem sorted itself out, in the future if you guys experience the problem, put ur phone close to a TUBE T.V, and let the static fix it for u, I was busy trying to get this OLD t.v sorted out in the Hotel where we are living in Bahrain, and I couldn't see at the back, and I used my phone as a flash light to see what's going on lol, and then my Touch screen started working again.........anyone care to explain this..?
Phone is in complete working order again, happy flashing for me once again hehe.
Man, I had the same problem and I was quite desperate. I was going to replace my Vodafone 1615 (the brandized version of Tytn II) when I found your post.
I put the phone near a CRT Monitor and then magically the touch-screen was working again!
Thank you to disclose your experience.
Can anyone explain why this might work?
I had the same problems. Touched yesterday mine htc kaiser with wet fingers and the touch screen did not respond. I thought that is the same problem with humidity that I had in Amazonia. That time it got solved by heating the phone with notebook. Pillow - kaiser - notebook for few hours :-D
But this time heating did not work... With doubt I approached old CRT tv and static energy from it SOLVED mine problem too. I am happy that I did not throw it away after buying LCD one. This is the time when new technology needs some old school energy :-D
rdee said:
With doubt I approached old CRT tv and static energy from it SOLVED mine problem too. I am happy that I did not throw it away after buying LCD one. This is the time when new technology needs some old school energy :-D
Click to expand...
Click to collapse
Did you have the phone off or on , did you touch it to the screen or side of tv, and how long did you hold the phone there, this would be awesome if it works, I've been freaking out the last couple of days.
me too! i brushed my phone around the tv for 30 seconds.. no luck...
ardley216 said:
me too! i brushed my phone around the tv for 30 seconds.. no luck...
Click to expand...
Click to collapse
I think we were fooled.
bwnotredame06 said:
I think we were fooled.
Click to expand...
Click to collapse
Static can kill touch screens
I killed my old WM2003 device by sliding down a plastic slide with my kids at the park.
Hi folks!
I had the same problem: change my at&t tilt rom/radio/spl to htc.
result: touch screen does not working!
The only way that i found is undo changes:
1º - installing and using: Remote screen Alignment to skip the first screen calibration. Just power on Tilt and wait until activesync are connected, so, run "remote screen alignment" and click skip, if the phone does not restart, do a soft reset.
2º - In the next power on, use activesync to copy JumpSPL1.56-KAIS.exe to your phone.
3º - use the buttons to navigate and execute JumpSPL1.56-KAIS.exe on the phone. (to execute JumpSPL1.56-KAIS.exe file use the ENTER key of the sliding keyboard).
4º- now just replace RUU_Kaiser_CINGULAR_WWE_.exe (OEM ROM i think)/ bootloader spl1.93.0/1.56 (maybe the screen problem occurs due the wrong spl/rom combination or newer spl like 3.28/3.29 ).
After these steps my AT&T Tilt touch screen is back to work!
Now i'm ready to try others roms again !!
PS: Sorry for poor english, if anybody don't understand anything just ask!
parmito said:
Hi folks!
I had the same problem: change my at&t tilt rom/radio/spl to htc.
result: touch screen does not working!
The only way that i found is undo changes:
1º - installing and using: Remote screen Alignment to skip the first screen calibration. Just power on Tilt and wait until activesync are connected, so, run "remote screen alignment" and click skip, if the phone does not restart, do a soft reset.
2º - In the next power on, use activesync to copy JumpSPL1.56-KAIS.exe to your phone.
3º - use the buttons to navigate and execute JumpSPL1.56-KAIS.exe on the phone. (to execute JumpSPL1.56-KAIS.exe file use the ENTER key of the sliding keyboard).
4º- now just replace RUU_Kaiser_CINGULAR_WWE_.exe (OEM ROM i think)/ bootloader spl1.93.0/1.56 (maybe the screen problem occurs due the wrong spl/rom combination or newer spl like 3.28/3.29 ).
After these steps my AT&T Tilt touch screen is back to work!
Now i'm ready to try others roms again !!
PS: Sorry for poor english, if anybody don't understand anything just ask!
Click to expand...
Click to collapse
thank you so much for taking the time to post your solution! My kaiser was dead after it got soaked in vinegair..keys were sticky, device wouldnt charge or even turn on..
what i did is put the kaiser in a bowl of water and let it rest for a few hours. Then i took it out and put it in a bowl of uncooked rice (rice sucks up water!) and let it rest overnight. My kaiser came out great with everything working fine except....the touchscreen wouldnt respond. I flashed several roms but all to no avail.
I then followed your instructions and miraculously this strange at&t rom brought my touchscreen back to life!
So thanks again

Touch screen not responding after hard reset..hardware problem?

I have searched for solutions for the past 2 days but cant find one, if i missed it or this post is redundant , i apologize in advance.
Now my tilt is driving me crazy. It started last week when The touch screen wasnt working, but i fixed it by doing a couple of soft resets. then all the sudden, everytime i slide my keyboard out, the touch screen would stop responding. this went on for a day, then yesterday, when i tired to use the keyboard, the screen went blank, like the light died or something. but when i put it back on portrait, the screen would light up again.
A few moments later, the touch was responding, tried to use the keypad then the screen went blank..tried soft resets about 5 times and uninstalled all recent added programs (skyfire) ..finally the screen was working but the touch still wasnt working.
So this morning, i had the bright idea to do a hard reset....dumbest idea ever cos now its stuck at the screen where i have to "tap the screen to set up your wm device" and guess what..the touch screen isnt responding
plz i really need help with this. all so , i have a broken tilt.., well lcd screen is cracked...can i try to dismantle both tilts and replace the screens?
Ok, i used Code Factory's Remote screen alignment to bypass the alignment, but if i cant use the touch screen or the keyboard, the phone is pretty much useless for sending any information or making calls..is there a way to fix this?
I have had this same issue with my tilt. I could use the scroller on the left side of the unit to navigate but no touch screen. Both times that this has happened to me I removed the screen protector that I had on and restored a backup that I had on my storage card (I run a backup weekly). This has always fixed my issue. You could try another hard reset, not sure if that will help but do you get any lights on the keyboard when you slide it open? Is your tilt less than a year old because there is a manufacturer's warranty too.
Jim
when i slide the keyboard, i do get lights on the keyboard but not on the screen...it just goes dead..but when i slide it back in, the screen comes to life.
I cant do another hard reset cos i have to input the "1,2,3,4" code.
Also , the phone just got out of the 1yr warranty this month...awesome
I want to buy a replacement screen with a new digitizer but i need to be sure that is the problem.. ive searched for this keyboard problem but still have no answers
Now I'm having the same issue, touch not responding. I first noticed it about two days ago, when I slide the keyboard out, I could type just fine, but when I went to send the message the touch screen wouldnt work, so I'd close the keyboard and it would work. well yesterday it stopped working all together, so i used my d-pad and did a sprite restore and it started working again. But then On my way home i hit the lock button, and it stopped working after that, and I couldn't get it unlocked. I used the inner soft key to hit the first part of unlock, but then I couldnt ever figure which button to hit to get the on screen part of the unlock. So I had no choice but to do a hard reset, and just like highoct now I'm stuck on the stylus setup , and the touch still doesnt respond. does anybody esle have any suggestions ? Thanks in advance.
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Oh yeah, I did manage to do a hard reset again, but now the screen is just white. I can hear the sound of it booting up but it still has a white screen. I tired going to the Bootloader screen ( Camera and power at the same time)...still have the white screen. I believe its a hardware problem but i don't know what it is...any ideas?
Ok now I've done a hard flash, using the same HTC kaiser rom 6.1 and it fixes the problem for a little bit, until the first time I slide out the keyboard , then the screen stops working again, any suggestions ?
iPhone 3G Screen Repair...finally an affordable answer
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Does this look like an apple website? did i say i had an iphone? GET OUT OF HERE!!!
Ninety Four said:
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Click to expand...
Click to collapse
And thats his only post, its spam. jerk him outta here
Tilt Touch Screen
highoct said:
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Click to expand...
Click to collapse
I know this thread is a bit old but was searching d forum for possible solutions cos yesterday i developed the same exact problem on my kaiser for no apparent reason!..flashing it hasnt helped and now im stuck on the wm setup screen..when u say u still have the same tilt with the original problem do you mean that the repair was unsuccessful? have you tried reparing it yourself? Thanks
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
grayfoxmg1 said:
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
Click to expand...
Click to collapse
same thing happened to me 3 days ago. touchscreen has just stopped responding.
it still worked when i slided my keyboard out, but only when it was out. then i realized it won't work at all (!) after soft reset. however, i could make it work again like that when i did the soft reset with the keyboard out. weird.
i tried searching, and decided to make a hard reset, flash a new rom, etc, etc., but no more touchscreen. at all. the device doesn't feel any touch in any case. nothing. i bypassed the beggining tap here with the storage card trick. (i've read it somewhere on the forum).
now i can only use my kaiser with the hw buttons, the keyboard, and that's it. no touch. really weird. please if anyone has any updates, solutions, anything, post. sniff sniff
mine doesn't have anything on the screen unless i slide it out, if i have it closed anymore, it just doesn't work at all.
try this:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
se1988 said:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
Click to expand...
Click to collapse
well, i tried both tips, but they didn't work. i'd like to say a big thanks anyway!
then i grabbed the kaiser service manual and took my device apart into pieces. i reconnected pretty much all the cables and stuff, but still no touchy. any further ideas?
you should try replacing the screen. im happy to say that this screen from this seller on eBay worked for me: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250539984183
look here for dissasembly video: http://www.fonlogix.tv/tiltlow.wmv
(to save it to desktop right click link and "save target as")
thanks for your help, i've just ordered a new screen! phew, i hope it's gonna work

touch screen not responding

Well ive had my phone for a while with hyperdragon iv iolite working completely fine without any hardware or software issues for months. Today i took out the battery of the phone, and put it back in and turned it on, but when the phone turned on, the touch scrren is not responding to anything. everything works fine with all the buttons and keyboard, but the touchscreen isnt working. What could have gone wrong just by taking out the battery. I also havnt dropped or damaged the phone in anyway so i dont see it being a hardware problem. Thanks. I really need help
I have heard of people who has been able to solve this problem by hard resetting the devise. I have had not such luck....comes to be that from sliding wear and tear the connector to the screen gets damaged. My screen is completely disable, I found someone that was able to buy a second hand phone on ebay and was able to switch the connector. Looks like to much of a hassle to me, so Im sticking with this until I switch phones.

Categories

Resources