plz help me, stuck in bootloader - Tilt, TyTN II, MDA Vario III General

when i power up i het the tri-color screen
upper right says : RUUNBH
n the rest says:
KAIS1*0
SPL-1.56.0000
CPLD-8

i am NO Expert, but can you try and load a new ROM? Or back to the AT&T rom?

1.- Hard SPL
2.- Flash another ROM
***********
if it doesnt work.
Try flashing the original stock ROM
and then flash the Hard SPL

Don't do any of that until you know why. Get MTTY & folow MY instructions.
1. Disable A/S USB Connections (DO NOT KILL RAPI or A/S)
2. Run MTTY 1.42 & with your device in BL (Tri-Color) slect the USB port, change the flow control to RTS/CTS & select OK or the USB Button.
3. Hit the enter key on your KB until you see this: cmd>
4. Enter this exactly & only this: info 8 (It should look like this (cmd>info 8) mind the space between info & the number 8.
5. Post or PM me the resuslts reported on the MTTY screen.
From there I can tell you why you're stuck & how to possibly fix it. Never try force flashing another ROM. If you have bad blocks it can make things worse!
If you need help you can PM me or find me on MSN IM ([email protected])

i have got my one like this
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 1494 (0x5D6) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x8B40
Partition[3], type=0x4, start=0x9880, total=0x11A40
CE Total Length(with sector info) = 0x4C8C400
CE CheckSum Length(without sector info) = 0x4C40000
Cmd>
GSLEON3 said:
Don't do any of that until you know why. Get MTTY & folow MY instructions.
1. Disable A/S USB Connections (DO NOT KILL RAPI or A/S)
2. Run MTTY 1.42 & with your device in BL (Tri-Color) slect the USB port, change the flow control to RTS/CTS & select OK or the USB Button.
3. Hit the enter key on your KB until you see this: cmd>
4. Enter this exactly & only this: info 8 (It should look like this (cmd>info 8) mind the space between info & the number 8.
5. Post or PM me the resuslts reported on the MTTY screen.
From there I can tell you why you're stuck & how to possibly fix it. Never try force flashing another ROM. If you have bad blocks it can make things worse!
If you need help you can PM me or find me on MSN IM ([email protected])
Click to expand...
Click to collapse

Sorry I missed you guy.
I need to know what SPL version you have though.
If you have HardSPL (or 1.52 or 1.56) you want to do this:
cmd>set 16 0
cmd>boot
That should probably clear the bad block. You may have to repeat the step twice.
faruqsavar said:
i have got my one like this
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 1494 (0x5D6) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x8B40
Partition[3], type=0x4, start=0x9880, total=0x11A40
CE Total Length(with sector info) = 0x4C8C400
CE CheckSum Length(without sector info) = 0x4C40000
Cmd>
Click to expand...
Click to collapse

SPL
GSLEON3 said:
Sorry I missed you guy.
If you have HardSPL (or 1.52 or 1.56) you want to do this:
cmd>set 16 0
cmd>boot
That should probably clear the bad block. You may have to repeat the step twice.
Click to expand...
Click to collapse
SPL 1.81.0000
CPLD 8
How do i clear the bad block thank you

Related

Bad Block doesn't allow to flash any radio ROM

Hi, in the last month I tried to fix this problem but without results.
I have a Treo 750v Vodafone Italy.
In the bootloader screen I see:
CHEE100
IPL-0.20
CHEE100
SPL-1.40.OliNex
I completed the CheetahUnlocker step 1 but the 2nd step fails.
I tried the SD method using the CheetahPatched.nbh file that I found in the tempChe directory but the procedure hangs after a little completion of the progress bar.
Here you find some mtty 1.42 outputs:
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x228(552) is BAD block !!!
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1800
Partition[2], type=0x25, start=0x3100, total=0x16600
Partition[3], type=0x4, start=0x19700, total=0x21900
CE Total Length(with sector info) = 0x33AB800
CE CheckSum Length(without sector info) = 0x32E0000
Cmd>task 2a
Check block : 552 - Bad
Cmd>info 3
CID: Wait interpreter timeout
HTCSC
Cmd>info 2
HTCS00000000jR*¥HTCE
Cmd>getdevinfo
CID: Wait interpreter timeout
GetDevInfo: Get backup CID
HTCSCHEE100HTCE
Cmd>checkimage
IPL CRC checksum = 0x1BFDBB23
SPL CRC checksum = 0x83944A98
CE CRC checksum = 0xDEBAE4B
ExtROM CRC checksum = 0xA49957DA
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
The phone can load the OS (Win Mobile 6.1) but obviously there's no GSM.
Could anyone help me?
Many Thanks
You have bricked you treo...
There are a lot of ways to unbrick your phone, just search for my older posts, the same has hapend to me, and know my treo works great...
[[]]

HELP!my kaiser seemed locked

My kaiser like this now!
Cann't into OS.when power on ,restart repeatly!only display "smart mobility" NOT display R/G/D.
Can flash offical ROM under enginerring mode.
when I flash "RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship" ROM. diaplay:
KAIS130
SPL-1.56.0000
CPLD-8
when I flash "Kaiser_hTC_ASIA_HK_CHT_3.34.708.2" ROM. diaplay:
KAIS130
SPL-3.34.0000
CPLD-8
I use mtty.exe
info 2
level=0
info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 1359 (0x54F) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x900
Partition[2], type=0x25, start=0xF40, total=0x9F00
Partition[3], type=0x4, start=0xAE40, total=0x10480
CE Total Length(with sector info) = 0x5777200
CE CheckSum Length(without sector info) = 0x5720000
I think my phone is locked,and I have not find the Original ROM.
I cann't into OS,how to SPL?
help me! thanks!
NO one can help me ???
Issue now here: http://forum.xda-developers.com/showthread.php?t=481937
Closed.
Dave

HELP! HTC Tilt stuck in Bootloader... nothing seems to work

Hi!
I'm kinda desperate ....
My phone ceased to work completelly today regardless the methods that I have tried.
First of all, after I ran out of battery, when I restarted the phone the Bootloader (tricolor) screen appeared:
These are the following lines:
KAIS1*0
SPL-3.02.0000
CPLD-8
RUUNBH
If I plug the USB cable , on the white zone of the screen the USB message replaces Serial BUT the computer gives me the "USB device not recognized" message.
I have tried on a different computer, I even unnistalled the WMDC from my computer and reinstalled.
Nothing works.
Please! Heeeelp!
Hi there,
Check here http://forum.xda-developers.com/showthread.php?t=423486
Update: I have tried the SD version 1 hour ago but the phone gets stuck at "Loading..." it's now 20 minutes since it's stuck like that...
I have tried with these files as KAISIMG.NBH:
RUU-SPLolipof1-nostuckinboot-forceusb.zip
RUU-329-patch-nostuckinSPL.zip
None of them worked :\
psvictor said:
Update: I have tried the SD version 1 hour ago but the phone gets stuck at "Loading..." it's now 20 minutes since it's stuck like that...
I have tried with these files as KAISIMG.NBH:
RUU-SPLolipof1-nostuckinboot-forceusb.zip
RUU-329-patch-nostuckinSPL.zip
None of them worked :\
Click to expand...
Click to collapse
Flash your stock rom.
UPDATE EDIT
UPDATE in progress...
I get the update complete message but when I soft reset the phone it goes back to the tricolor mode :\
UPDATE:
I have extracted RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe, renamed KaiserIMG_CINGULAR_WWE_3.57.502.0_radio_sign_25.88.40.05_1.65.21.14_Test0.nbh to KAISIMG.nbh and copied it on my SD card.
I ran the SDcard in and the installation was again complete but after the soft reset it returns to the Bootloader showing:
KAIS1*0
SPL-3.56.0000
CPLD-8
Now the computer can see the device but active sync doesn't
I have tried MTTY but it does not show the USB port but COM1 and COM2 only.
Any other suggestions?
I have managed to make the computer sort of recognize the device...
If I pull out the battery and insert the USB plug in the computer sees the device but I still cannot connect through MTTY.
The only ROM that I can fully install (as soon as it's completed it returns to tricolor mode) is the very first version that the device has been shipped with.
Forgot to add that it's an ATT Tilt.
is it possible that the damage can be a permanent one or should I keep praying?
you have done a good advance, regarding your last issue you can check here http://forum.xda-developers.com/showthread.php?t=420683:)
Mr. Clown said:
you have done a good advance, regarding your last issue you can check here http://forum.xda-developers.com/showthread.php?t=420683:)
Click to expand...
Click to collapse
First off all, thank you for all the patience and advices Mr. Clown
I think that I have tried all the possible combinations with both KaisdiagSD and a SPL but all of them get stuck in the same white screen with "Loading..."
I have also tried the Diag and Flash via USB but that didn't work either.... same story, same Loading screen.
Since I bought a battery like 2 weeks ago, I tried replacing with my old one , I shorted the terminals (I guess I did it well since the phone rebooted) but that didn't seem to work out either.
I guess I should take it to a mobile phone service, unless another ideea pops out.
UPDATE:
I think I have managed to make some progress...
While scrolling and google-ing all day long I have managed to find a driver for my Win 7 x64 USB that makes my phone visible to MTTY ...
Here it is for those having trouble with their Tilt/Tytn/whatever.
Atm I could make only two of the commands respond and this is the result:\
info 0
Platform Model ID:KAIS1*000
Platform HW Board ID:31, PVT1
Cmd>info 2
HTCSCWS__001Ùü¤HHTCE
Later edit:
I flashed a new Stock ROM via SD card...
while using MTTY:
Cmd>set 14 0
HTCST ÚÈÒHTCE
Cmd>set 16 0
nothing happends
Update:
Installed the "primordial" ROM for my Tilt which I found on the forum...
http://forum.xda-developers.com/showthread.php?t=327482
Now the phone does respond to the Boot command in MTTY and this is what I get as a result:
The phone however now shows some scrambled colors on the screen alongside the Tricolor mode
__________________________________________________________________
Cmd>boot
Fill RSVD information for block 288 to 309
Storage start sector=0xAB80, total sector=0x10740
Storage start block=707, total block=1053
Total Bad Block in CE: 0
Erase physical block from 995 to 2032
formatstorage Bad block found: 1458
si backup: Erase physical block from 2032 to 2048
No card inserted
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage crc of Mini-Kernel:0x872BBCB8
OEMLaunchImage 80000000
Jump to Physical Address 10300000
_________________________________________________________________
info 8 results:
_________________________________________________________________
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 1170 (0x492) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x9E40
Partition[3], type=0x4, start=0xAB80, total=0x10740
CE Total Length(with sector info) = 0x5615C00
CE CheckSum Length(without sector info) = 0x55C0000
______________________________________________________________
KAIS 1*0 MFG
SPL 1.50.1000
CPLD-8
Conclusion...I think it's broken
UPDATE:
I think that the phone actually has a HW problem after all....
I started it this morning (after a week of silence) and on the screen "TEST ONLY" "NOT FOR SALE" appeared and the AT&T logo
Trying now with the last software update and maybe I can make it work again

Help !!!!! Kaiser 4550

I followed a procedure mtty: set 16 0, task 8, task 0 result:
Power and blank screen with vibration. (thus, not in bootloader after power-up)
But when I put it in bootloader goes like this:
KAIS130
SPL-1.181.0000
CPLD-8
(no longer the RUUNBH)
I tried again from sd with KAISIMG KAISDIAG and remains in loading.
From Sd with official rom: Loading, checking, with over 00280.. Not Allow
Pc with official rom comes to 1% and reboots back to the white screen with vibration.Will post with mtty info 2 and 8 info:
info 2
HTCST-MOB005¼ôàŠHTCE
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 1105 (0x451) is bad block
OS NOT FOUND !!!
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
No card inserted
OSSIPreLoad ++
OSSIPreLoad failed, CE is NONE
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
FMD_ReadSector+, bad block no=0x15C40, status:0x0
FMD_ReadSector+, bad block no=0x15C40, status:0x0
FMD_ReadSector+, bad block no=0x15C40, status:0x0
IPLMSG:0x2:ERROR: Failed to open storage partition.
then I followed this procedure, see Annex:
Is there a solution to this problem?
Thanks in advance
Hi, last week I had the same problem. I solved it the next way:
1. I change hard-spl (v3.56) to the Kaiser
2. Install Android
3. Put back WM original
4. Do again hard-spl (v3.56) and put to the Kaiser a cooked rom.
Sorry for my bad english, I'm hungarian. Good luck,and if you have questions while you are doing the procedure, ask me.
I will post a guide post?
I remind you that the cell does not make me install anything, and also the mobile device center, I did not recognize. : (
you have read the attached txt?
ps. sorry for my English but I am using a translator because I'm Italian.
nobody can give me a solution??
Thanks

Need help kaiser, OS NOT FOUND !!!

Dear Guys,
I got problem with my kaiser after install and reinstall android. Now my bootloader just :
KAIS130
SPL-156.0000
CPLD-8
1. can not connected to laptop by activesync because activesync not detect the device.
2. USB detected by MTTY
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
No card inserted
OSSIPreLoad ++
OSSIPreLoad failed, CE is NONE
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
IPLMSG:0x2:ERROR: Failed to open storage partition.
and
Cmd>info 2
HTCSDOPAS601.¿OHTCE
3. I tried to HardSPL as on many thread but always stuck at 0% white screen.
4. flashing with cingular at 16% then reboot to whitescreen..
5. Flashing ROM from SD just got stuck loading.. on white screen..
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 8 (0x8) is reversed block
OS NOT FOUND !!!
Any Suggestion? Please.. and Thanks

Categories

Resources