Database Develop

GPRS and 3G stopped working?

Since this afternoon my phone will not connect to either GPRS and/or 3G anymore.. it will just keep trying and after 2 tries it gives me an error that the connection has failed...
Does anyone know whats going on?
i tried soft-resetting and reconfigure my provider settings with the htc provder wizard..
help??

I cant enable WLAN either..!! chip fried? i drove my car today and it was VERY hot (no airco)
changing the radio to 1.65.20.29 also didnt work..

How hot are we talking? My tilt has been in 90d Fahrenheit cars without ill effects.
Did you try a hard reset?

just tried a hard reset and it still doesnt work! omg..
i think around 115F / 45C
*edit; it seems that my provider has some problems. lets hope it will be over,
Wifi is fixed with an other commanager..
Code:
Cmd>task 32
Cmd>info 2
HTCS00000000jR*¥HTCE
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0x7DC0
Partition[3], type=0x4, start=0x8B40, total=0x12780
CE Total Length(with sector info) = 0x45E5A00
CE CheckSum Length(without sector info) = 0x45A0000
Cmd>getdevinfo
GetDevInfo: Get backup CID
HTCSKAIS1300HTCE
Cmd>

Who's your provider ?

My guess would be Vodaphone

i feel very stupid, it was my provider.. well it was strange because my phone acted weird at the same as well, AND because my commanager was broken wlan couldnt be activated via commanager, so i kinda freaked out i guess..
problem solved!

bootloader mode only?

When soft reset my Tilt will go into Bootloader mode if not plugged into USB charger only. Plugged into USB to PC goes to Bootloader when soft reset and as soon as plugged in the screen freezes and is unresponsive to any type of input/buttons. Nothing plugged in goes to Bootloader on soft reset. Won't synch, PC doesn't see it.
Got some help from GSLEON, but his solutions didn't work. I flashed his Jump spl and his Hard spl, worked, kinda, for a day or two, now it's as described above. I think GSLEON grew too busy, or disinterested, he did try but doesn't respond anymore.
Anyone else got a clue? Anyone know how to erase/delete the bad block shown below?
The screen reads;
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
running info 8 via mtty yields;
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 221 (0xDD) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x7B80
Partition[3], type=0x4, start=0x88C0, total=0x12A00
CE Total Length(with sector info) = 0x44A4600
CE CheckSum Length(without sector info) = 0x4460000
Any help would be appreciated.
Thanks,
Ed
Tilt running Blackwood rom and radio 1.27.14.0

sorry, but GSLEON knows what he is talking about and if he won't reply anymore I would only assume you weren't following his steps correctly and he got tired of spoon feeding "maybe". Sounds like you keep flashing back an incompatible radio or ROM which would cause it to recurre. If you can get the phone to sync with the PC then I would flash back the original ROM and start back at the beginning, maybe some Wiki reading would help.

I'm assuming he got busy, as he was when we started. Please don't assume I did anything wrong, even if you are sorry.
I followed his steps exactly, as we were on chat at the time. It seemed to work for a day, then went south. There isn't any bad rom or radio on it, they've been working for months. Suddenly a block went bad, hence the problem, according to GSLEON.
I find it hard to believe he is the only person on this site with that kind of knowledge willing to help. He is a good guy, and he doesn't assume incorrectly, he finds the facts.
I've read just about everything in the Wiki pertaining to the Kaiser, and done extensive searching on the problem. I only ask as a last resort, knowing, and understanding why, that newbs get flamed for not doing the research first.
If I could only get it to synch, I could live with it the way it is, alas the problem.
Thanks for your attempt at helping. I appreciate anything coming my way.
Ed
KDKobes said:
sorry, but GSLEON knows what he is talking about and if he won't reply anymore I would only assume you weren't following his steps correctly and he got tired of spoon feeding "maybe". Sounds like you keep flashing back an incompatible radio or ROM which would cause it to recurre. If you can get the phone to sync with the PC then I would flash back the original ROM and start back at the beginning, maybe some Wiki reading would help.
Click to expand...
Click to collapse

My Kaiser's playing dead! just boots to boot loader screen

Hi folks,
I wonder if anyone knows the answer to...
I had it flashed with 'Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06', which seemed to be working OK.
Then I soft reset it earlier today and it got to loading my today screen, screamed the battery was dead (it was nearly fully charged) and turned off.
I turned it back on and it was as though it was booting after the soft reset, or like I'd taken the battery out (I hadn't).
I couldn't get this to change, so I flashed it with Sleuth v3.0, one ive used very successfully before - then it had no sound at all once it had booted.
I tried another hard-reset and now it only shows the tri-colour bootloader screen, with the following details:
KAIS130 MFG
SPL-1.0.0.oliPoF
CPLD-8
USB
Anyone know what I can do?
Thanks in advance
'tunes

Check out this thread on MTTY. But be careful! One slip with MTTY and you could forever kill your phone.

done it - same thing!
I'm starting to get worried!
I've kept searching and tried everything I've found, with no rteal luck.
What I have found though, is that if I connect using MTTY, and use 'boot' - my phone boots and works just fine!
However, if I reset te device at all I just end up back at the boot loader screen.
Because I've tried all sorted, Here's the output of a few things from MTTY, it might help:
The tri-color screen doesnt show "RUURUN" or similar
########################################
Cmd>task 32
Cmd>info 2
HTCS00000000jR*¥HTCE
Cmd>getdevinfo
GetDevInfo: Get backup CID
HTCSKAIS1300HTCE
###########################################
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 43 (0x2B) is bad block
BLOCK 46 (0x2E) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0x8700
Partition[3], type=0x4, start=0x9480, total=0x11E40
CE Total Length(with sector info) = 0x4A8A400
CE CheckSum Length(without sector info) = 0x4A40000
############################################
Cmd>boot
InitDisplay: Display_Chip=1
Card inserted
Cmd5 CMD_TIMEOUT
SD 2.0 LC card
SD Init OK
SDFATChkConf: RhOpenFile() failed KAISCONF.txt
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
Anyone got any recommendations.....pleease?
A huge thanks in advance,
'tunes
Added details to a thread already discussing this:
http://forum.xda-developers.com/showthread.php?p=2244462&posted=1#post2244462
Feel free to remote this thread
'tunes

HELP!!!! - tytnii doesn't boot

Hi all, I'm getting out of ideas on how to solve this... please help me....
My Tytn II powers on, appears the first screen ( Smart Mobility ) and after ~5 seconds it powers off. It nevers shows the R/G/D versions...
Recently I had to open the device because of white screen - usually it is the flat cable that comes lose and you have to tighten it...
Maybe it is related!
It looks like it is missing the bootloader.
The output from mtty says I don't have corrupt blocks in memory:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 830 (0x33E) is bad block
BLOCK 922 (0x39A) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x8C80
Partition[3], type=0x4, start=0x99C0, total=0x11900
CE Total Length(with sector info) = 0x4D2CE00
CE CheckSum Length(without sector info) = 0x4CE0000
Cmd>
ON THE OTHER HAND, he cannot communicate with the mainboard properly:
Cmd>info 7
CPLD ID=0x8
Cmd>
This output should be much more complete, I believe.
I have an original SPL, and never flashed any ROM in the device.
What I've tried:
-flash original HTC rom from SD card - it will start loading, but in the end says "not allow"
-tried to do hard-reset but the outcome is the same - after the smart mobility, turns off
WHAT COULD BE the next step? Is there any thing that I'm not seeing?
Please advise, experts, as I really need the device up and running...
Thanks in advance,
LM

It looks like a battery problem to me, have you try another battery? Maybe that's causing the problem.

[Q] Can't get a hard SPL to take.

Hi,
I am trying to update my Kaiser, so for the last few weeks, I have read LOADS of threads, FAQ's, and Tutorials on the subject.
I am very well versed in PC Hardware, and a bit of a technogeek, but this is the first smart phone I have had (a cast off from a friend of mine).
I have followed the many threads on the upgrading process, and have managed a few bits of the process, but I am now stuck at burning the Kaiser-HardSPL-3.56-Hard2.nbh.
(BTW I picked this because it seemed to be the latest version, and as I will be going to Win 6.5, I just thouight it "best" to start with).
I start up the PDA, wait for the OS, connect the USB cable and sync.
When that is finished, on the PDA, I run explorer and then run JumpSPL1.94-KAIS.exe from device memory.
The PDA reboots to the tri coloured screen and shows:
Security Unlocked
KAIS130
SPL-1.94.0000
CPLD-8
USB
I unplug the USB cable, wait for 15 secs, plug the cable back in.
On the PC, I un-tick 'Allow USB Connections', then I run KaiserCustomRUU.exe (with the .nbh file in the same folder).
The PC reports back that it is checking the information on the PDA, then the progress bar appears on the PC and the PDA.
They both jump to 100% in about 1 sec, then the PDA reboots itself. When I check the information on boot up, or with a 'camera-stylus' reset, the information displayed is exactly the same as it was before the procedure.
I've tried it on an XP (x32) machine using Active Sync, and a Win 7 (x64) machine using Windows Mobile Device Center, and I get the same results every time
I have performed many soft and hard resets of the Kaiser, many reboots of the PC's, and much cursing....
At the moment -
On boot-up, I have:
R 1.70.OliNex
G 25.65.30.04H
D 3.28.00.00
At the tri coloured screen, I have:
Security Unlocked
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
USB
Output from Mtty 1.42:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 648 (0x288) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0xAA40
Partition[3], type=0x4, start=0xB7C0, total=0xFB00
CE Total Length(with sector info) = 0x5C3BE00
CE CheckSum Length(without sector info) = 0x5BE0000
Cmd>
The OS is Windows Mobile 6.1 Pro
CE OS 5.2.19212 (Build 19212.1.0.3)
Am I being thick here ? or should the "SPL-1.0.OliPof" on the tri-coloured screen change ?
Please can someone give me a bit of guidance.
Thanks & Regards,
Paul

its done silly

ljohnson1981 said:
its done silly
Click to expand...
Click to collapse
So why doesn't the "SPL-1.0.OliPof" on the tri-coloured screen change to "HardSPL-3.56-Hard2" or something similar ?
Regards,
Paul

Moving to General. Hardly Development related.